Assessing the Efficiency of Antimicrobial Plant Extracts from Artemisia afra and Eucalyptus globulus as Coatings for Textiles.

This study aimed to assess the antimicrobial activities of plant extracts from Artemisia afra and Eucalyptus globulus when used as coatings for textiles. A pulsed ultrasound-assisted extraction method (PUAE) was employed to obtain methanolic and hexanoic extracts from both plants. Eucalyptus globulus methanol extraction exhibited the highest yield at 22.76% (±0.61%), while Artemisia afra demonstrated lower yields. Phytochemical screening identified various secondary metabolites in the extracts, including phenols, quinones, and steroids. Antimicrobial tests against Staphylococcus aureus and Escherichia coli revealed varying degrees of susceptibility, with Eucalyptus globulus hexanoic extracts showing the highest activity against Staphylococcus aureus at an average percentage growth of 18.74% (±0.26%). Minimum inhibitory concentration (MIC) values were determined for the extracts, but complete inhibition did not occur at concentrations below 500 µg/mL. The extracts exhibited varying effects on Staphylococcus aureus and Escherichia coli growth, with some extracts promoting bacterial growth. Coating textiles with Eucalyptus globulus methanolic extracts demonstrated antibacterial activity against Staphylococcus aureus with the highest zone of inhibition observed in cotton-coated samples (258.4 mm2). Polyester-coated samples exhibited smaller inhibition zones, with the lowest observed in Eucalyptus globulus methanolic extract coating (65.97 mm2). Scanning electron microscope (SEM) analysis revealed visible surface morphology changes in coated fabrics, depicting fine, cluster, lumpy, flaky, and fragment-like morphologies. Laundering effects on coated fabrics were investigated, showing a significant decrease in antimicrobial activity after washing. Fourier-transform infrared spectroscopy (FTIR) identified functional groups in the extracts associated with antimicrobial properties. The complexity of the bioactive compounds suggests potential antimicrobial efficacy, resting on factors such as geographical location, climate, and extraction methods. Notwithstanding the limitations, this study contributes valuable insights into the use of plant extracts as antimicrobial coatings for textiles.

Wearable Loop Sensor for Bilateral Knee Flexion Monitoring.

We have previously reported wearable loop sensors that can accurately monitor knee flexion with unique merits over the state of the art. However, validation to date has been limited to single-leg configurations, discrete flexion angles, and in vitro (phantom-based) experiments. In this work, we take a major step forward to explore the bilateral monitoring of knee flexion angles, in a continuous manner, in vivo. The manuscript provides the theoretical framework of bilateral sensor operation and reports a detailed error analysis that has not been previously reported for wearable loop sensors. This includes the flatness of calibration curves that limits resolution at small angles (such as during walking) as well as the presence of motional electromotive force (EMF) noise at high angular velocities (such as during running). A novel fabrication method for flexible and mechanically robust loops is also introduced. Electromagnetic simulations and phantom-based experimental studies optimize the setup and evaluate feasibility. Proof-of-concept in vivo validation is then conducted for a human subject performing three activities (walking, brisk walking, and running), each lasting 30 s and repeated three times. The results demonstrate a promising root mean square error (RMSE) of less than 3° in most cases.

Evaluating the fire resistance and durability of cotton textiles treated with a phosphoramide phosphorus ester phosphate ammonium flame retardant.

The phosphoramide phosphorus ester phosphate ammonium (PPEPA) flame retardant was synthesized by phosphorus oxychloride and ethanolamine, and its structure was characterized by nuclear magnetic resonance and Fourier transform infrared spectroscopy (FTIR). Cotton textiles treated with 20 wt% PPEPA (CT-PPEPA3) would have high durability and flame retardance. The limiting oxygen index (LOI) of CT-PPEPA3 was found to be 46.5 %, while after undergoing 50 laundering cycles (LCs) following the AATCC 61-2013 3 A standard, the LOI only decreased to 31.4 %. Scanning electron microscopy and X-ray diffraction analyses suggested the penetration of PPEPA molecules into the interior of cotton fibers, resulting in a minor alteration of the cellulose crystal structure. The excellent durability, FTIR, and energy-dispersive X-ray of CT-PPEPA3 provided evidence for the formation of -N-P(=O)-O-C- and -O-P(=O)-O-C- covalent bonds between the PPEPA molecules and cellulose. The -N-P(=O)-O-C- bond exhibited a p-π conjugation effect, leading to enhanced stability and improved durability of the flame-retardant cotton textiles. Vertical flame, thermogravimetric, and cone calorimetry tests demonstrated that the CT-PPEPA3 underwent condensed-phase and synergistic flame retardation. Additionally, these finished cotton textiles retained adequate breaking strength and softness, making them suitable for various applications. In conclusion, the incorporation of the -N-P(=O)-ONH4 group into the phosphorus ester phosphate ammonium flame retardant demonstrated effective enhancement of the fire resistance and durability of treated cotton textiles.

Antimicrobial Coatings for Medical Textiles via Reactive Organo-Selenium Compounds.

Bleached and cationized cotton fabrics were chemically modified with reactive organoselenium compounds through the nucleophilic aromatic substitution (SNAr) reaction, which allowed for organo-selenium attachment onto the surface of cotton fabrics via covalent bonds and, in the case of the cationized cotton fabric, additional ionic interactions. The resulting textiles exhibited potent bactericidal activity against S. aureus (99.99% reduction), although only moderate activity was observed against E. coli. Fabrics treated with reactive organo-selenium compounds also exhibited fungicidal activities against C. albicans, and much higher antifungal activity was observed when organo-selenium compounds were applied to the cationized cotton in comparison to the bleached cotton. The treatment was found to be durable against rigorous washing conditions (non-ionic detergent/100 °C). This paper is the first report on a novel approach integrating the reaction of cotton fabrics with an organo-selenium antimicrobial agent. This approach is attractive because it provides a method for imparting antimicrobial properties to cotton fabrics which does not disrupt the traditional production processes of a textile mill.

Wearable Neuromuscular Electrical Stimulation on Quadriceps Muscle Can Increase Venous Flow.

Neuromuscular electrical stimulation (NMES) of the quadriceps (Q) may increase venous blood flow to reduce the risk of venous thromboembolism. This study assessed whether Q-NMES pants could increase peak venous velocity (PVV) in the femoral vein using Doppler ultrasound and minimize discomfort. On 15 healthy subjects, Q-NMES using textile electrodes integrated in pants was applied with increasing intensity (mA) until the first visible muscle contraction [measurement level (ML)-I] and with an additional increase of six NMES levels (ML II). Discomfort using a numeric rating scale (NRS, 0-10) and PVV were used to assess different NMES parameters: frequency (1, 36, 66 Hz), ramp-up/-down time (RUD) (0, 1 s), plateau time (1.5, 4, and 6 s), and on:off duty cycle (1:1, 1:2, 1:3, 1:4). Q-NMES pants significantly increased PVV from baseline with 93% at ML I and 173% at ML II. Frequencies 36 Hz and 66 Hz and no RUD resulted in significantly higher PVV at both MLs compared to 1 Hz and 1 s RUD, respectively. Plateau time, and duty cycle did not significantly change PVV. Discomfort was only significantly higher with increasing intensity and frequency. Q-NMES pants produces intensity-dependent 2-3-fold increases of venous blood flow with minimal discomfort. The superior NMES parameters were a frequency of 36 Hz, 0 s RUD, and intensity at ML II. Textile-based NMES wearables are promising for non-episodic venous thromboembolism prevention.

Hands on Biofilm! Utilizing a public audience in a citizen science project to assess yield variability when culturing kombucha pellicle.

The pellicle biofilm generated during the Kombucha tea fermentation process has, when dried, textile-like properties that may have real-life applications. However, pellicle yield can vary depending on inoculation and incubation conditions, which affects research investigations on the properties of the pellicle. To generate data on variability to help define optimum pellicle growth conditions, as part of a public engagement event about biofilm, a citizen science activity was hosted whereby visitors to a science festival were invited to select incubation conditions and inoculate different media with liquid or solid (pellicle). More than 220 samples were inoculated (in excess of 1200 visitors, mainly in family groups). The most popular incubation conditions were coconut water or tea medium, 30°C/room temperature and liquid inoculum. The most productive/reproducible in terms of yield and variability were tea medium, 30°C, and liquid inoculum, which reflect some of the conditions most used in the domestic setting for kombucha culture. The event provided both useful research data and generated public interest in a research area of which many will have been unaware. Interest in the results of the activity, available several weeks after the activity, was sustained using email contact and FlickR for the dissemination of images and data.

Magneto-Responsive Textiles for Non-Invasive Heating.

Magneto-responsive textiles have emerged lately as an important carrier in various fields, including biomedical engineering. To date, most research has been performed on single magnetic fibers and focused mainly on the physical characterization of magnetic textiles. Herein, from simple woven and non-woven textiles we engineered materials with magnetic properties that can become potential candidates for a smart magnetic platform for heating treatments. Experiments were performed on tissue-mimicking materials to test the textiles' heating efficiency in the site of interest. When the heat was induced with magneto-responsive textiles, the temperature increase in tissue-mimicking phantoms depended on several factors, such as the type of basic textile material, the concentration of magnetic nanoparticles deposited on the textile's surface, and the number of layers covering the phantom. The values of temperature elevation, achieved with the use of magnetic textiles, are sufficient for potential application in magnetic hyperthermia therapies and as heating patches or bandages.

Plants and Other Materials Used for Dyeing in the Present Territory of Poland, Belarus and Ukraine according to Rostafinski's Questionnaire from 1883.

BACKGROUND: Traditional dyeing methods are practically forgotten in Poland. Józef Rostafinski included questions on the use of dyes in his ethnobotanical survey from 1883. METHODS: 126 questionnaires contained information on dye plants. They were identified by the respondents using folk names or sometimes even Latin names. Folk names were analyzed by comparison with other literature. Several voucher specimens were also present. RESULTS: 74 plant taxa were identified to genus or species level. The most commonly used were: onion (Allium cepa), brazilwood (Caesalpinia brasiliensis or Paubrasilia echinata), winter corn (mainly rye Secale cereale), black alder (Alnus glutinosa), safflower (Carthamus tinctorius), apple (Malus domestica), birch (Betula pendula), oak (Quercus robur), and violet flowering spring flowers (mainly Hepatica nobilis and Pulsatilla spp.). CONCLUSIONS: Most species are well known in the literature about plant dyeing, but the paper provides extra details on the picture of dyeing traditions in Eastern Europe.

Electronic textiles: New age of wearable technology for healthcare and fitness solutions.

Sedentary lifestyles and evolving work environments have created challenges for global health and cause huge burdens on healthcare and fitness systems. Physical immobility and functional losses due to aging are two main reasons for noncommunicable disease mortality. Smart electronic textiles (e-textiles) have attracted considerable attention because of their potential uses in health monitoring, rehabilitation, and training assessment applications. Interactive textiles integrated with electronic devices and algorithms can be used to gather, process, and digitize data on human body motion in real time for purposes such as electrotherapy, improving blood circulation, and promoting wound healing. This review summarizes research advances on e-textiles designed for wearable healthcare and fitness systems. The significance of e-textiles, key applications, and future demand expectations are addressed in this review. Various health conditions and fitness problems and possible solutions involving the use of multifunctional interactive garments are discussed. A brief discussion of essential materials and basic procedures used to fabricate wearable e-textiles are included. Finally, the current challenges, possible solutions, opportunities, and future perspectives in the area of smart textiles are discussed.

Durability Study of Thermal Transfer Printed Textile Electrodes for Wearable Electronic Applications.

Textile-based electronics hold great promise because they can endow wearable devices with soft and comfortable characteristics. However, the inherent porosity and fluffiness of fabrics result in high surface roughness, which presents great challenges in the manufacture of high-performance fabric electrodes. In this work, we propose a thermal transfer printing method to address the above challenges, in which electrodes or circuits of silver flake/thermoplastic polyurethane (TPU) composites are prefabricated on a release film by coating and laser engraving and then laminated by hot-pressing to a variety of fabrics and textiles. This universal and scalable production technique enables fabric electrodes to be made without compromising the original wearability, washability, and stretchability of textiles. The prepared fabric electrodes exhibit high conductivity (5.48 × 104 S/cm), high adhesion (≥1750 N/m), good abrasion/washing resistance, high patterning resolution (∼40 µm), and good electromechanical performance up to 50% strain. To demonstrate the potential applications, we developed textile-based radio frequency identification (RFID) tags for remote identification and a large-sized heater for wearable thermotherapy. More importantly, the solvent-free thermal transfer printing technology developed in this paper enables people to DIY interesting flexible electronics on clothes with daily tools, which can promote the commercial application of smart textile-based electronics.

Antimicrobial and Antiviral Activities of Durable Cotton Fabrics Treated with Nanocomposite Based on Zinc Oxide Nanoparticles, Acyclovir, Nanochitosan, and Clove Oil.

In this study, cotton fabrics based on zinc oxide nanoparticles in situ synthesis, acyclovir, nanochitosan, and clove oil were treated. The treated cotton fabrics were examined by FTIR, HR-TEM, FE-SEM, EDAX, and the surface roughness processing of FE-SEM images. The obtained characterization data emphasized the nano-size of nanocomposite with high homogeneity of particles in spherical shape as well as affirmed the deposition of nanocomposite onto the textile fibers with concluded that the deposition of nanocomposite was increased parallel with sonication time. Antimicrobial and antiviral activities of treated cotton fabrics were evaluated. Results revealed that treated cotton fabrics exhibited promising antibacterial activity toward Gram-positive higher than Gram-negative bacteria. Likewise, treated cotton fabrics are still effective as antibacterial after washing for 100 cycles. Moreover, treated cotton fabrics exhibited potential antifungal activity against Candida albicans, Aspergillus niger, and Aspergillus fumigatus. The antiviral activity significantly depended on the type of virus. The treated cotton fabrics showed antiviral activity against tested viral particles (HSV-1, Adeno, and CoxB2) with viral inhibition of 95.9, 76.4, and 86.9% respectively, while in the case of coated cotton textile with acyclovir, it only exhibited viral inhibition of 49.9, 41, and 22.3% respectively.

Bioactivity of Chitosan-Based Particles Loaded with Plant-Derived Extracts for Biomedical Applications: Emphasis on Antimicrobial Fiber-Based Systems.

Marine-derived chitosan (CS) is a cationic polysaccharide widely studied for its bioactivity, which is mostly attached to its primary amine groups. CS is able to neutralize reactive oxygen species (ROS) from the microenvironments in which it is integrated, consequently reducing cell-induced oxidative stress. It also acts as a bacterial peripheral layer hindering nutrient intake and interacting with negatively charged outer cellular components, which lead to an increase in the cell permeability or to its lysis. Its biocompatibility, biodegradability, ease of processability (particularly in mild conditions), and chemical versatility has fueled CS study as a valuable matrix component of bioactive small-scaled organic drug-delivery systems, with current research also showcasing CS's potential within tridimensional sponges, hydrogels and sutures, blended films, nanofiber sheets and fabric coatings. On the other hand, renewable plant-derived extracts are here emphasized, given their potential as eco-friendly radical scavengers, microbicidal agents, or alternatives to antibiotics, considering that most of the latter have induced bacterial resistance because of excessive and/or inappropriate use. Loading them into small-scaled particles potentiates a strong and sustained bioactivity, and a controlled release, using lower doses of bioactive compounds. A pH-triggered release, dependent on CS's protonation/deprotonation of its amine groups, has been the most explored stimulus for that control. However, the use of CS derivatives, crosslinking agents, and/or additional stabilization processes is enabling slower release rates, following extract diffusion from the particle matrix, which can find major applicability in fiber-based systems within ROS-enriched microenvironments and/or spiked with microbes. Research on this is still in its infancy. Yet, the few published studies have already revealed that the composition, along with an adequate drug release rate, has an important role in controlling an existing infection, forming new tissue, and successfully closing a wound. A bioactive finishing of textiles has also been promoting high particle infiltration, superior washing durability, and biological response.

Light-Emitting Textiles: Device Architectures, Working Principles, and Applications.

E-textiles represent an emerging technology aiming toward the development of fabric with augmented functionalities, enabling the integration of displays, sensors, and other electronic components into textiles. Healthcare, protective clothing, fashion, and sports are a few examples application areas of e-textiles. Light-emitting textiles can have different applications: sensing, fashion, visual communication, light therapy, etc. Light emission can be integrated with textiles in different ways: fabricating light-emitting fibers and planar light-emitting textiles or employing side-emitting polymer optical fibers (POFs) coupled with light-emitting diodes (LEDs). Different kinds of technology have been investigated: alternating current electroluminescent devices (ACELs), inorganic and organic LEDs, and light-emitting electrochemical cells (LECs). The different device working principles and architectures are discussed in this review, highlighting the most relevant aspects and the possible approaches for their integration with textiles. Regarding POFs, the methodology to obtain side emissions and the critical aspects for their integration into textiles are discussed in this review. The main applications of light-emitting fabrics are illustrated, demonstrating that LEDs, alone or coupled with POFs, represent the most robust technology. On the other hand, OLEDs (Organic LEDs) are very promising for the future of light-emitting fabrics, but some issues still need to be addressed.

In situ synthesis of silver or selenium nanoparticles on cationized cellulose fabrics for antimicrobial application.

In this study, we developed a method to prepare inorganic nanoparticles in situ on the surface of cationized cellulose using a rapid microwave-assisted synthesis. Selenium nanoparticles (SeNPs) were employed as a novel type of antimicrobial agent and, using the same method, silver nanoparticles (AgNPs) were also prepared. The results demonstrated that both SeNPs and AgNPs of about 100 nm in size were generated on the cationized cellulose fabrics. The antibacterial tests revealed that the presence of SeNPs clearly improved the antibacterial performance of cationized cellulose in a similar way as AgNPs. The functionalised fabrics demonstrated strong antibacterial activity when assessed using the challenge test method, even after repeated washing. Microscopic investigations revealed that the bacterial cells were visually damaged through contact with the functionalised fabrics. Furthermore, the functionalised fabrics showed low cytotoxicity towards human cells when tested in vitro using an indirect contact method. In conclusion, this study provides a new approach to prepare cationic cellulose fabrics functionalised with Se or Ag nanoparticles, which exhibit excellent antimicrobial performance, low cytotoxicity and good laundry durability. We have demonstrated that SeNPs can be a good alternative to AgNPs and the functionalised fabrics have great potential to serve as an anti-infective material.

Textile-integrated polymer optical fibers for healthcare and medical applications.

With ever growing interest in far-reaching solutions for pervasive healthcare and medicine, polymer optical fibers have been rendered into textile forms. Having both fiber-optic functionalities and traditional fabric-like comfort, textile-integrated polymer optical fibers have been advocated to remove the technical barriers for long-term uninterrupted health monitoring and treatment. In this context, this paper spotlights and reviews the recently developed textile-integrated polymer optical fibers in conjunction with fabrication techniques, applications in long-term continuous health monitoring and treatment, and future perspectives in the vision of mobile health (mHealth), as well as the introductory basics of polymer optical fibers. It is designed to serve as a topical guidepost for scientists and engineers on this highly interdisciplinary and rapidly growing topic.

Multifunctional Electronic Textiles Using Silver Nanowire Composites.

Textiles represent an appealing platform for continuous wearable applications due to the exceptional combination of compliance, water vapor permeability, and comfortableness for long-term wear. We present mechanically and electrically robust integration of nanocomposites with textiles by laser scribing and heat press lamination. The simple and scalable integration technique enables multifunctional E-textiles without compromising the stretchability, wearability, and washability of textiles. The textile-integrated patterns exhibit small line width (135 µm), low sheet resistance (0.2 Ω/sq), low Young's modulus, good washability, and good electromechanical performance up to 50% strain, which is desirable for wearable and user-friendly electronic textiles. To demonstrate the potential utility, we developed an integrated textile patch comprising four dry electrophysiological electrodes, a capacitive strain sensor, and a wireless heater for electrophysiological monitoring, motion tracking, and thermotherapy, respectively. Beyond the applications demonstrated in this paper, the materials and methods presented here pave the way for various other wearable applications in health care, activity tracking, rehabilitation, sports medicine, and human-machine interactions.

Development of a Function-Integrative Sleeve for Medical Applications.

Function-integrative textiles bear the potential for a variety of applications in the medical field. Recent clinical investigations suggest that the application of a function-integrative fabric could have a positive impact on currently applied diagnostic procedures of a specific type of tumour. In this context, the fabric should enable local warming of a patient's upper extremity as well as blood flow measurement. Existing solutions comprise a warming a warming system but lack a measuring apparatus for blood flow determination. With regard to the quality of results of current diagnostic procedures, the local warming of the patients' upper extremity and the simultaneous determination of the blood flow plateau are crucial. In the present paper, the development process of a function-integrative sleeve is introduced. Besides the development of an adaptable sleeve-design, the manufacturing process of an integrated warming system was also addressed. Furthermore, the identification of crucial physiological effects, using a Laser Doppler Perfusion Monitor, is introduced. During testing of the function-integrative sleeve, modulation of the desired physiological effects was observed. The results support the initial assumptions and dictate further investigations on increasing user-friendliness and cost-efficiency during adjusting and determining the physiological effects in the course of tumour diagnosis.

Onion (Allium cepa L.) Skin: A Rich Resource of Biomolecules for the Sustainable Production of Colored Biofunctional Textiles.

The aqueous extract of dry onion skin waste from the 'Dorata di Parma' cultivar was tested as a new source of biomolecules for the production of colored and biofunctional wool yarns, through environmentally friendly dyeing procedures. Specific attention was paid to the antioxidant and UV protection properties of the resulting textiles. On the basis of spectrophotometric and mass spectrometry analyses, the obtained deep red-brown color was assigned to quercetin and its glycoside derivatives. The Folin⁻Ciocalteu method revealed good phenol uptakes on the wool fiber (higher than 27% for the textile after the first dyeing cycle), with respect to the original total content estimated in the water extract (78.50 ± 2.49 mg equivalent gallic acid/g onion skin). The manufactured materials showed remarkable antioxidant activity and ability to protect human skin against lipid peroxidation following UV radiation: 7.65 ± 1.43 (FRAP assay) and 13.60 (ORAC assay) mg equivalent trolox/g textile; lipid peroxidation inhibition up to 89.37%. This photoprotective and antioxidant activity were therefore ascribed to the polyphenol pool contained in the outer dried gold skins of onion. It is worth noting that citofluorimetric analysis demonstrated that the aqueous extract does not have a significative influence on cell viability, neither is capable of inducing a proapoptotic effect.

Mild extraction methods using aqueous glucose solution for the analysis of natural dyes in textile artefacts dyed with Dyer's madder (Rubia tinctorum L.).

Madder (Rubia tinctorum L.) has been widely used as a red dye throughout history. Acid-sensitive colorants present in madder, such as glycosides (lucidin primeveroside, ruberythric acid, galiosin) and sensitive aglycons (lucidin), are degraded in the textile back extraction process; in previous literature these sensitive molecules are either absent or present in only low concentrations due to the use of acid in typical textile back extraction processes. Anthraquinone aglycons alizarin and purpurin are usually identified in analysis following harsh back extraction methods, such those using solvent mixtures with concentrated hydrochloric acid at high temperatures. Use of softer extraction techniques potentially allows for dye components present in madder to be extracted without degradation, which can potentially provide more information about the original dye profile, which varies significantly between madder varieties, species and dyeing technique. Herein, a softer extraction method involving aqueous glucose solution was developed and compared to other back extraction techniques on wool dyed with root extract from different varieties of Rubia tinctorum. Efficiencies of the extraction methods were analysed by HPLC coupled with diode array detection. Acidic literature methods were evaluated and they generally caused hydrolysis and degradation of the dye components, with alizarin, lucidin, and purpurin being the main compounds extracted. In contrast, extraction in aqueous glucose solution provides a highly effective method for extraction of madder dyed wool and is shown to efficiently extract lucidin primeveroside and ruberythric acid without causing hydrolysis and also extract aglycons that are present due to hydrolysis during processing of the plant material. Glucose solution is a favourable extraction medium due to its ability to form extensive hydrogen bonding with glycosides present in madder, and displace them from the fibre. This new glucose method offers an efficient process that preserves these sensitive molecules and is a step-change in analysis of madder dyed textiles as it can provide further information about historical dye preparation and dyeing processes that current methods cannot. The method also efficiently extracts glycosides in artificially aged samples, making it applicable for museum textile artefacts.

Exposure of women to trace elements through the skin by direct contact with underwear clothing.

Heavy metals pose a potential danger to human health when present in textile materials. In the present study, inductive coupled plasma mass spectrometry (ICPMS) was used to determine the concentrations and the identity of extractable inorganic elements from different brands of women undergarments. A total of 120 samples consisting of 63 cottons, 44 nylons and 13 polyesters manufactured in 14 different countries having different colors were analyzed for their extractable metals contents. Elements analyzed were Ag, Al, As, Ba, Be, Bi, Ca, Cd, Co, Cr, Cu, Fe, Hg, K, Li, Mg, Mn, Na, Ni, Pb, Sb, Se, Sr, Ti, V and Zn. Cotton undergarments were rich in Al, Fe and Zn, nylon undergarments had high levels of Cr, Cu and Al, while polyester fabrics contained higher levels of Ni and Fe compared to cotton or nylon. With respect to manufacturing countries, China, Egypt and India showed the highest concentrations of metals in all fabrics. With respect to the color, black garments were characteristic by high concentration of Fe, blue colors with Cu, brown garments with Fe and Cu, green garments with Cu and Fe, pink garments with Al, purple garments with Al and Cu and red garments with Cr, Zn and Al. The consumer should be made aware of the potential dangers of these metals in their clothing.