Assessment of medicinal plants colonizing abundantly on metal-enriched fly ash deposits: phytoremediation prospective.

Heavy metal-enriched fly ash (FA) deposits are recognized as hazardous contaminated sites on the earth, which pollute our ecosystems. Consequently, the present investigation was carried out to explore the phytoremediation potential of naturally growing medicinal plants in the FA dumpsite. This present study chose two native medicinal plants i.e., Bacopa monnieri and Acmella oleracea found to be naturally colonizing abundantly on FA dumpsite to assess heavy metal accumulation. FA sample of B. monnieri thriving sites found to have metal content in order Mn (216.6)> Cr (39.27)> Zn (20.8)> Ni (16.1)> Cu (15.03)> Co (6.7)> Pb (5.43) whereas for A. oleracea FA dumpsites, the order of metal availability was Mn (750.3)> B (54.5)>Cr (37.2)>Zn (31.33)> Cu (18.7)> Ni (16.93)> Co (7.7)>Pb (4.23). In B. monnieri, higher concentrations of Cr and Mn were observed in the shoot in comparison to the root, indicative of its potential as a hyperaccumulator plant. Conversely, in A. oleracea, greater amounts of Pb were detected in the shoot relative to the root. Hence, it is recommended that B. monnieri and A. oleracea grow on such heavy metal-enriched substrates should be avoided for medicinal purposes; however, these plants can be used for phytoremediation purposes.

Fly ash phytoremediation through natural colonizer plant species is limited.Native colonizing plant species on fly ash has a pivotal role in phytoremediation.Naturally colonizing medicinal plants were dominant over the Fly ash dumpsites.Bacopa monnieri and Acmella oleracea have phytoremediation potential on fly ash.Indeed, fly ash-grown medicinal plants should not be used by local communities.

Preparation of phosphorus containing products by co-incineration of sludge ash and calcium-based additives: Focusing one-step and multi-step method.

Due to the irreplaceable nature of phosphorus (P) in biological growth and the shortage of P rock, it is necessary to recover P from waste, such as sludge ash. P-containing products were prepared using sludge ash and calcium-based additives (CaCO3 and eggshell). In addition, the effects of different incineration methods (one-step method (OSM) and multi-step method (MSM)), additive doses, and incineration temperature on the P content and species in the products were investigated. The results indicated that as the dose of calcium-based additives increased, total P (TP) content in P-containing products reduced, apatite P (AP) content increased, non-apatite P (NAIP) content declined, and P solubility in citric acid content decreased. The amount of AP increased, NAIP reduced, and P solubility in citric acid decreased as the incineration temperature climbed. Although P in P-containing products prepared by OSM and MSM changed in a similar way at different additive doses and temperatures, P-containing products prepared by MSM had at least a 6.1% increase in P solubility in citric acid. Compared with OSM, MSM could save 10% of calcium-based additives when reaching the maximum AP value. Additionally, pure materials were employed to investigate how P species changed during the incineration procedure. The advantage of the MSM-prepared product over the OSM-prepared product may be explained by the high concentration of Ca3(PO4)2 and low concentration of amorphous calcium bound P (Ca-P). Overall, MSM is an effective method to reduce the dose of calcium-based additives and increase the bioavailability of P in P-containing products.

Characterization and mechanical removal of metallic aluminum (Al) embedded in weathered municipal solid waste incineration (MSWI) bottom ash for application as supplementary cementitious material.

Municipal solid waste incineration (MSWI) bottom ash, due to its high mineral content, presents great potential as supplementary cementitious material (SCM). Weathering, also known as aging, is a treatment process commonly employed in waste management to minimize the risk of heavy metal leaching from MSWI bottom ash. Using weathered MSWI bottom ash to produce blended cement pastes is considered as a high-value-added and sustainable waste disposal solution. However, a critical challenge arises from the metallic aluminum (Al) in weathered MSWI bottom ash, which is known to induce detrimental effects such as volume expansion and strength loss of blended cement pastes. While most metallic Al in weathered MSWI bottom ash can be removed with eddy current separators in metal recovery plants, the residual metallic Al, owing to its small particle size, cannot be removed with the same technique. This study is dedicated to addressing this issue. An in-depth analysis was conducted on residual metallic Al embedded in weathered MSWI bottom ash particles, aiming to guide the removal of this metal. This analysis revealed that mechanical removal was the most suitable method for extracting metallic Al. The specific processes and mechanisms underlying this method were elucidated. After reducing metallic Al content in weathered MSWI bottom ash by 77 %, a significant improvement in the quality of blended cement pastes was observed. This work contributes to the broader adoption of mechanical treatments for removing residual metallic Al from weathered MSWI bottom ash and facilitates the application of treated ash as SCM.

Use of municipal solid waste incineration fly ash as a supplementary cementitious material: CO2 mineralization coupled with mechanochemical pretreatment.

The use of municipal solid waste incineration fly ash, commonly referred to as "fly ash", as a supplementary cementitious material (SCM), has been explored to mitigate the CO2 emissions resulting from cement production. Nevertheless, the incorporation of fly ash as an SCM in mortar has been shown to weaken its compressive strength and increase the risk of heavy metal leaching. In light of these challenges, this study aims to comprehensively evaluate the influence of CO2 pressure, temperature, and residual water/binder ratio on the CO2 uptake and compressive strength of mortar when combined with fly ash. Additionally, this study systematically examines the feasibility of mechanochemical pretreatment, which enhances the homogenization of fly ash and augments the density of the mortar's microstructure. The results indicate that the use of mechanochemical pretreatment leads to a notable 43.6% increase in 28-day compressive strength and diminishes the leaching of As, Ba, Ni, Pb, Se, and Zn by 17.9-77.8%. Finally, a reaction kinetics model is proposed to elucidate the CO2 sequestration process under varying conditions. These findings offer valuable guidance for incorporating fly ash as an SCM and CO2 sequestrator in mortar.

Novel surface-treatment for bottom ash from municipal solid waste incineration to reduce the heavy metals leachability for a sustainable environment.

Unconventional treatments can provide a modification to convert ash waste into valuable materials that can be used in various applications. This study focuses on bottom ash (BA) collected from a local incineration plant and characterizes its chemical composition before and after pretreatment by coating with polymers. The toxicity-characteristic leaching procedure (TCLP) was used to identify selected heavy metal leaching after treatment with vinyl-terminated polydimethylsiloxane (PDMS) of different molecular weights. BA coatings were incorporated in two ratios, 0.5% and 1%, by milling to avoid heavy metal leaching. The results showed that all the coating batches had reduced concentrations of copper (Cu), manganese (Mn), and zinc (Zn), whereas the concentrations of chromium (Cr) and cadmium (Cd) showed higher amounts of BAV34 (0.5%) and BAV25 (1%). The treated BA with GP demonstrated percentages of reduction of 70%, 65%, 80%, 75%, 90%, and 80% for Cu, Mn, Ni, Zn, Pb, and Cd, respectively. The milling procedure reduced the particle size of the coated ash. Hydrophobicity was observed in all coating batches compared to untreated BA. The thermogravimetric analysis (TGA) results showed variations between BA and treated BA, which confirmed that PDMS caused surface modification. These features have potential significance for extending the use of coated ash as a sustainable material for construction applications.

Examining the residual radiological footprint of a former colliery: An industrial nuclear archaeology investigation.

Nuclear industrial archaeology utilises radiation mapping and characterisation technologies to gain an insight into the radiological footprint of industrial heritage sites. Increased concentrations of naturally occurring radioactive materials at legacy mine sites are the result of elemental enrichment during coal mining and subsequent combustion. Public safety is of concern around these sites, and therefore, an increased understanding of their associated hazard is essential. Using coincident laser scanning and gamma detection technologies, this study sought to assess the radiological legacy of a coal mine located in Bristol, UK. From this, we can increase our understanding of the residual footprints associated with the local coal mining industry. Samples taken from inside the site were characterised using high resolution gamma spectrometry, wherein the radionuclide content and activities of samples were then quantified. An area of elevated low-level radioactivity was observed at and around buildings believed to belong to the colliery, while Th, U, and K are confirmed at the site from photopeak's of daughter radionuclides. Activities of the radionuclides K-40, U-238, and Th-232 were further quantified during subsequent laboratory analysis. Results highlight an enrichment of naturally occurring radionuclides when compared with global averages for unburned coal. Employing these techniques at further legacy sites would enable an increased understanding of the lasting traces of the coal mining industry, with a focus on NORM enrichment in residual fly ash.

Coal fly ash application as an eco-friendly approach for modulating the growth, yield, and biochemical constituents of Withania somnifera L. plants.

The solid waste known as fly ash, which is produced when coal is burned in thermal power plants, is sustainably used in agriculture. It is an excellent soil supplement for plant growth and development since it contains some desired nutrients (macro and micro), as well as being porous. The present study was done to evaluate the effect of different fly ash levels on Withania somnifera. The present study aimed to assess the impact of various fly ash (FA) concentrations on growth, yield, photosynthetic pigments, biochemical parameters, and cell viability of W. somnifera. The results showed that FA enhanced physical and chemical properties of soil like pH, electric conductivity, porosity, water-holding capacity, and nutrients. The low doses of FA-amended soil (15%) significantly increased the shoot length (36%), root length (24.5%), fresh weight of shoots and roots (107.8 and 50.6%), dry weight of shoots and roots (61.9 and 47.1%), number of fruits (70.4%), carotenoid (43%), total chlorophyll (44.3%), relative water content (109.3%), protein content (20.4%), proline content (110.3%), total phenols (116.1%), nitrogen (20.3%), phosphorus (16.9%), and potassium (26.4%). On the other hand, the higher doses, i.e., 25% of fly ash showed a negative effect on all the above parameters and induced oxidative stress by increasing lipid peroxidation (33.1%) and hydrogen peroxide (102.0%) and improving the activities of antioxidant enzymes and osmolytes. Compared to the control plants, the plants growing in soil enriched with 15 and 25% fly ash had larger stomata pores when examined using a scanning electron microscope. In addition, according to a confocal microscopic analysis of the roots of W. somnifera, higher fly ash concentrations caused membrane damage, as evidenced by an increase in the number of stained nuclei. Moreover, several functional groups and peaks of the biomolecules represented in the control and 15% of fly ash were alcohols, phenols, allenes, ketenes, isocynates, and hydrocarbons. Gas chromatography-mass spectrometry analysis of the methanol extract of W. somnifera leaves cultivated in soil amended with 15% fly ash shows the presence of 47 bioactive compounds. The most abundant compounds in the methanol extract were cis-9-hexadecenal (22.33%), n-hexadecanoic acid (9.68%), cinnamic acid (6.37%), glycidyl oleate (3.88%), nonanoic acid (3.48%), and pyranone (3.57%). The lower concentrations of FA (15%) can be used to enhance plant growth and lower the accumulation of FA that results in environmental pollution.

Accumulation of pollutants from fly ash in Pleurotus ostreatus and a substrate based on coffee grounds by elemental analysis using the ICP-OES method and photometric method.

The substrate mixtures were created in the study, using spent coffee grounds for Pleurotus ostreatus cultivation with the addition of straw and fluidized bed ash at 5 and 10 percent by weight relative to the total weight of coffee grounds. In order to determine the ability to accumulate heavy metals and the possibility of further waste management, analyses of micro- and macronutrients, biogenic elements, as well as the metal content of fungal fruiting bodies, mycelium and post-cultivation substrate were performed. The addition of 5 percent resulted in slower growth of mycelium and fruiting bodies, and with the addition of 10 percent, the growth of fruiting bodies was completely inhibited. The accumulation of elements such as (Cr), (Cu), (Ni), (Pb) and (Zn) was reduced in the fruiting bodies grown on the substrate with the addition of 5 percent fly ash, compared to spent coffee grounds without additives.

High performance C-A-S-H seeds from fly ash-carbide slag for activating lithium slag towards a low carbon binder.

In this work, one-step synthesis of high-performance C-A-S-H (calcium alumina silicate hydrate) seeds from low-calcium fly ash (FA) and carbide slag (CS) by 7 days of mechanochemical mixing was proposed and used to activate lithium slag (LS) cement. The results showed that the seeding effect of C-A-S-H seeds was increased with the increasing Ca/Si (i.e. from 1.0 to 1.5), i.e. the mortar compressive strength of 1 day and 28 days were increased by 67% and 29% with the addition of 1.0% C-A-S-H nano-seeds at Ca/Si = 1.5 in the presence of polycarboxylate superplasticizer (PCE), respectively. Moreover, the chloride resistance of lithium slag cement was improved significantly, i.e. the electric flux was decreased by more than 30% than that of plain lithium slag cement mortar. The performance difference of various C-A-S-H seeds is mainly attributed to their high proportion and polymerization degree, more stretch and three-dimensional foil-like morphology at high Ca/Si. This study provides guidance for obtaining low-cost and high-performance C-A-S-H seeds from wastes and the highly efficient utilization of LS as supplementary cementitious materials (SCMs) in the future.

Cycling of phosphorus from wastewater to fertilizer using wood ash after energy production.

Quercus wood was used for thermal energy production, and wood bottom ash (WDBA) was used as a medium for water purification and soil fertilizer in accordance with the recently proposed food-water-energy nexus concept. The wood contained a gross calorific value of 14.83 MJ kg-1, and the gas generated during thermal energy production has the advantage of not requiring a desulfurization unit due to its low sulfur content. Wood-fired boilers emit less CO2 and SOX than coal boilers. The WDBA had a Ca content of 66.0%, and Ca existed in the forms of CaCO3 and Ca(OH)2. WDBA absorbed P by reacting with Ca in the form of Ca5(PO4)3OH. Kinetic and isotherm models revealed that the results of the experimental work were in good agreement with the pseudo-second-order and Langmuir models, respectively. The maximum P adsorption capacity of WDBA was 76.8 mg g-1, and 6.67 g L-1 of WDBA dose could completely remove P in water. The toxic units of WDBA tested using Daphnia magna were 6.1, and P adsorbed WDBA (P-WDBA) showed no toxicity. P-WDBA was used as an alternative P fertilizer for rice growth. P-WDBA application resulted in significantly greater rice growth in terms of all agronomic values compared to N and K treatments without P. This study proposed the utilization of WDBA, obtained from thermal energy production, to remove P from wastewater and replenish P in the soil for rice growth.

Blending bauxite residues with multiple byproducts improves capping materials for tailings storage facilities.

Amelioration and management of large volumes of tailings resulting from alumina refining is a major challenge owing to the high alkalinity and salinity of residues. Blended byproduct caps are a potential new and more cost-effective approach to tailings management, where tailings are blended with other local byproducts in order to reduce pH, salinity and toxic elements. Here, alkaline bauxite residue was blended with four byproducts (waste acid, sewage water, fly ash and eucalypt mulch) to create a range of potential capping materials. We leached and weathered materials in the glasshouse with deionized water over nine weeks to investigate if byproducts on their own or in combination improved cap conditions. Combining all four byproducts (10 wt % waste acid, 5 wt % sewage water, 20 wt % fly ash and 10 wt % eucalypt mulch) achieved lower pH (9.60) compared to any byproduct applied individually, or un-remediated bauxite residue (pH 10.7). Leaching decreased EC by dissolving and exporting salts and minerals from the bauxite residue. Fly ash addition increased organic carbon (likely from non-combusted organic material) and nitrogen, while eucalypt mulch increased inorganic phosphorus. Addition of byproducts also decreased the concentration of potentially toxic elements (e.g., Al, Na, Mo and V) and enhanced pH neutralisation. Initial pH with single byproduct treatments was 10.4-10.5, which decreased to between 9.9-10.0. Further lowering of pH and salinity as well as increased nutrient concentrations may be possible through higher addition rates of byproducts, incorporation of other materials such as gypsum, and increasing leaching/weathering time of tailings in situ.

Value-added application of cattle manure bottom ash for phosphorus recovery from water and replenishment in soil.

This study addresses ways to circulate the flow of phosphorus (P) from water to soil to improve water quality and provide a sustainable supply of P into soil. Here, bottom ash (BA_CCM), the byproduct of the combustion of cattle manure, which is performed for obtaining energy, was used to remove P in wastewater. Next, the P-captured BA_CCM was used as P fertilizer for rice growth. BA_CCM was primarily composed of Ca (49.4%), C (24.0%), and P (9.9%), and the crystalline phases of Ca were calcium carbonate (CaCO3) and hydroxyapatite (Ca5(PO4)3OH). The mechanism of P removal by BA_CCM involves the formation of hydroxyapatite by reacting Ca2+ with PO43-. A reaction time of 3 h was required to achieve P adsorption to BA_CCM, and the maximum P adsorption capacity of BA_CCM was 45.46 mg/g. The increase in solution pH reduced P adsorption. However, at pH > 5, the P adsorption amount was maintained regardless of the pH increase. The presence of 10 mM SO42- and CO32- reduced P adsorption by 28.4% and 21.5%, respectively, and the impact of the presence of Cl- and NO3- was less than 10%. The feasibility of BA_CCM was tested using real wastewater, and 3.33 g/L of BA_CCM dose achieved a P removal ratio of 99.8% and a residual concentration of <0.02 mg/L. The toxicity unit of BA_CCM determined for Daphnia magna (D. magna) was 5.1; however, the BA_CCM after P adsorption (P-BA_CCM) did not show any toxicity to D. magna. BA_CCM after P adsorption was used as an alternative to commercial P fertilizer. Rice fertilized with a medium level of P-BA_CCM showed better agronomic values for most agronomic traits, except root length, than that seen with the commercial P fertilizer. This study suggests that BA_CCM can be used as a value-added product to address environmental issues.

Biogenic sunflower oil-chitosan decorated fly ash nanocomposite film using white shrimp shell waste: Antibacterial and immunomodulatory potential.

A new sunflower oil-chitosan decorated fly ash (sunflower oil/FA-CSNPs) bionanocomposite film was synthesized using the extract of Litopenaeus vannamei (White shrimp) and evaluated as an antibacterial and immunomodulatory agent. Fly ash-chitosan nanoparticles were produced by using chitosan (CS) isolated from white shrimp extract, glacial acetic acid and sodium tripolyphosphate solution as cross-linkage. The ultrafine polymeric sunflower oil-CS film was fabricated by treating fly ash-chitosan nanoparticles with sunflower oil in glacial acetic acid under continuous stirring for 24 h. The nanostructure of the fabricated polymeric film was confirmed and characterized by different microscopic and spectroscopic approaches. The surface morphology of pre-synthesized bionanocomposite film was found to be homogenous, even and without cracks and pores. The crystallinity of formed bionanocomposite film was noticed at angles (2θ) at 12.65°, 15.21°, 19.04°, 23.26°, 34.82°, and 37.23° in the XRD spectrum. The fabricated film displayed excellent stability up to 380 °C. The formed sunflower oil/FA-CSNPs bionanocomposite film showed promising antibacterial towards Bacillus subtilis with highest zone of inhibition of 34 mm and Pseudomonas aeruginosa with zone of inhibition of 28 nm. The as-synthesized bionanocomposite film exhibited highest cell viability effect (98.95%), followed by FA-CSNPs (83.25%) at 200 µg mL-1 concentrations. The bionanocomposite film exerted notable immunomodulatory effect by promoting phagocytosis and enhancing the production of cytokines (NO, IL-6, IL-1ß, and TNF-α) in macrophage-derived RAW264.7 cell line.

Magnetite/ß-cyclodextrin/fly ash composite as an effective and recyclable adsorbent for uranium(VI) capture from wastewater.

As a novel adsorbent for the separation of uranium(VI) from wastewater, Magnetite/ß-cyclodextrin/fly ash composite (Fe3O4/ß-CD/FA) was first prepared via a chemical coprecipitation technology. The characterization results indicated that Fe3O4 and ß-CD had been successfully loaded on FA, which had brought abundant oxygen-containing functional groups, providing numerous adsorptive sites for the removal of uranium(VI). At pH = 5.0 and T = 25 °C, the maximum uranium(VI) removal efficiency and capacity of Fe3O4/ß-CD/FA were higher to 97.8% and 444.4 mg g-1, respectively. Pseudo-second-order and Langmuir models fitted better with the experimental data, illustrating that chemical adsorption dominated the uranium(VI) removal process. In addition, Fe3O4/ß-CD/FA showed good anti-interference ability and recoverability. After five cycles, the removal rate of uranium(VI) on Fe3O4/ß-CD/FA was still higher to 90.4%. The immobilization of uranium(VI) on Fe3O4/ß-CD/FA was mainly ascribed to the synergism of redox reaction, complex reaction, chemical reaction and electrostatic interaction. Given the above, Fe3O4/ß-CD/FA would be regarded as an efficacious, green and promising adsorbent for uranium(VI) separation from wastewater.

Investigation of mineral commodity residues based on alkalinity, solubility and other physicochemical aspects aiming the management of amazonian acidic soils.

The large amounts of mineral residues generated by the bauxite-alumina industries in the Amazon - with a production scale in the same order of magnitude as their source commodities - have been seen as new sources of raw materials (secondary mines) and/or an inseparable part of a sustainable production system, i.e., a source for the generation of co-products within a circular economy system. In the present study, two alkaline residues from this mining-metallurgical industry were assessed for their potential to amend productive acidic Amazonian soils, namely, (1) insoluble solid residue from the Bayer process (bauxite residue, BR) and (2) ash from energy production from coal (coal combustion residues, CCRs: fly ash, FA, and bottom ash, BA). A physicochemical investigation was performed to evaluate the possible benefits that these residues can offer to the soil‒plant system. The alkalinity of the residues was adjusted "to a value of pH 8-10" by leaching with H3PO4 using a central composite experimental design. The chemical analyses indicated high levels (total and soluble) of essential elements such as Ca and S in the CCRs. All residues showed a high cation exchange capacity (CEC). Regarding the water holding capacity (WHC), FA showed a higher value than the other residues (68.6%). After pH adjustment, available P increased significantly for all residues, and the Ca and S contents remained high for the CCRs, while in BR, there was a decrease in available Na, and aluminum (Al3+) was not available because the potential acidity (H + Al) < 0.6. Finally, complementary analyses showed that with respect to mineralogy, BR is composed mainly of iron oxyhydroxides and aluminosilicate phases, while carbonate, sulfide and silicate phases dominate the CCRs. The neutralizing character, the presence of nutrients in the CCRs and the unavailability of Al3+ in BR are positive physicochemical characteristics for the management of Amazonian acid soils; the use of this residues would add to the circular economy and sustainability of the Amazon.

Regulation of ash slagging behavior of palm oil decanter cake by alum sludge addition.

Combustion of palm oil decanter cake (PODC) is a propitious alternative waste to energy means. However, the mono-combustion of PODC prompt severe ash slagging behavior which give rise to reduction in heat transfer and also shorten the lifespan of combustion reactors. In this study, alum sludge (AS) was introduced at different proportion of 30%, 50% and 70% to revamp the slagging characteristics of PODC during combustion. The addition of AS improved ash fusion temperature of PODC during co-combustion as ash fusion temperature increased significantly under high AS dosage. Slagging and fouling indices showed that at 50% AS addition, slagging tendency of the co-combustion ashes can be ignored. The predictive model for PODC-AS combustion showed good correlation coefficient with 0.89. Overall, co-combustion of PODC and AS is an ideal ash related problem-solving route. The proposed PODC slagging preventive method by AS was based on: (1) limited amount of aluminum content in PODC-AS system resulted in development of refractory ash (2) reduction in proportion of basic oxide which act as ash bonding glue played important role in the regulation of slagging (3) reduction of cohesive bond by formation of spongy and porous structure which prevented ash slagging.

Thermal and mechanical properties of coal gasification slag based foam concrete.

Foam concrete possesses low density and excellent thermal insulation properties and has been widely used in construction industry. Considering the recycling and reusing of coal gasification slag (CGS), a solid waste product in the coal chemical industry, CGS was used as the supplementary cementations material to prepare foam concrete (CGS-FC) in this work. The influence of the CGS content and water-binder ratio on the pore structure, mechanical and thermal properties was investigated. The results show that the CGS content and water-binder ratio directly impact the fluidity of the slurry, which affects the internal pore structure of the specimens after molding. And a CGS-FC with a compressive strength of 6.89 MPa, thermal conductivity of 0.24 W/m K, and a bulk density of 867 kg/m3 was successfully produced when the CGS content was 30% and water-binder ratio was 0.5. In particular, the utilization of CGS to prepare foam concrete product has recycling efficiency and environmental benefit.

[Availability Changes in Different Exogenous Selenium Fertilizers in Soil and Their Effects on Selenium Accumulation in Wheat].

In order to understand the differences in the uptake and accumulation of several common exogenous selenium fertilizers by crops, a wheat pot experiment was conducted to study the availability changes in different selenium fertilizers (potassium selenate, potassium selenite, EDTA-chelated selenium, selenium powder, fly ash, and selenium-enriched straw) in soil and their effects on wheat growth and selenium uptake and distribution. The results showed that the change in availability of different exogenous selenium types in soil was different. During the whole growth period of wheat, the soil available selenium proportion of selenate, selenite, and EDTA-chelated selenium treatment was significantly higher than that of the control (CK), respectively, but there was no significant difference between the other treatments and the CK treatment. In the early stage of wheat growth, the soil available selenium proportion of selenate, selenite, and selenium powder treatment decreased gradually and tended to be stable in the later growth stage of wheat; however, the soil available selenium proportion of other exogenous selenium treatments showed a dynamic change of decreasing in the early period and increasing in the late period. The available selenium content in soil significantly affected the selenium uptake by wheat, and there was a significant positive correlation between them. Selenate application significantly increased the grain and leaf biomass of wheat, but other selenium fertilizers had no significant effect on wheat growth. The accumulation capacity of different exogenous selenium fertilizers for wheat followed the order of selenate>selenite, EDTA-chelated selenium>selenium powder, fly ash, and selenium-enriched straw. There was no significant difference between the selenium powder, fly ash, and selenium-enriched straw treatments and the CK treatment. Selenium was more easily transferred to and accumulated in the stems and leaves of wheat after the application of selenate, whereas selenium was more easily transferred to and accumulated in grains after the application of selenite and EDTA-chelated selenium.

Environmental Impacts of Coal Combustion Residuals: Current Understanding and Future Perspectives.

On-site solid-waste impoundments, landfills, and receiving water bodies have served as long-term disposal sites for coal combustion residuals (CCRs) across the United States for decades and collectively contain billions of tons of CCR material. CCR components include fine particulate material, minerals, and trace elements such as mercury, arsenic, selenium, lead, etc., which can have deleterious effects on ecosystem functioning and public health. Effects on communities can occur through consumption of drinking water, fish, and other aquatic organisms. The structural failure of impoundments, water infiltration, leakage from impoundments due to poor construction and monitoring, and CCR effluent discharges to water bodies have in the past resulted in harmful environmental impacts. Moreover, the risks posed by CCRs are present to this day, as coal continues to account for 11% of the energy production in the United States. In this Critical Review, the legacy of CCR disposal and the concomitant risks posed to public health and ecosystems are assessed. The resiliency of CCR disposal sites in the context of increased frequency and intensity of storm events and other hazards, such as floods and earthquakes, is also evaluated. We discuss the current state of knowledge on the environmental fate of CCR-derived elements, as well as advances in and limitations of analytical tools, which can improve the current understanding of CCR environmental impacts in order to mitigate the associated risks. An assessment of the 2015 Coal Ash Final Rule is also presented, along with needs to improve monitoring of CCR disposal sites and regulatory enforcement.

Application of aluminum oxide nanoparticles in asphalt cement toward non-polluted green environment using linear regression.

In order to decrease the greenhouse gas emissions generated by regular Portland cement (OPC), additional cementitious ingredients have been frequently employed, even while building road bases. OPC's susceptibility to moisture and lack of flexibility make it ineffective for stabilizing road bases. This research used alkali-activated materials (AAM) with fly ash to investigate the mechanical properties of cold asphalt binder (freeze-thaw cycles) including the compressive, flexural strength, workability and porosity of cement. Dry specimens and specimens in distilled water have both been used in the experiments to study these temperature correlations. One sample was tested at 20 °C, and the other was frozen and thawed five times at a temperature of -5 °C (cold region environment). The resulting mixtures' morphologies and microstructures were analyzed via SEM images. During the 7 to 28-day curing period, the mixture's growth ratio rose. The combination registered both the greatest and lowest robust elastic modulus. The total compressive strength of the material decreased as the water-to-cement ratio increased due to the greater amount of free water accessible with a higher cationic asphalt emulsion (CAE) content. The moderate loss of flexural strength with increasing CAE concentration after 7 and 28 days of curing was seen. There is not a major impact on flexural strength in the materials by looking at the very modest gaps in flexural strength between 7 and 28 days curing periods. Due to the particle shape and size of this precursor, FA's inclusion allowed for a lower water to binder rate while maintaining a similar level of workability. The porosity and water absorption values rose with FA substitutions. Further studies might clarify the lower flexural strength observed in this study by adding other hybrids plus fly ash such as lime or nanoparticles.