Study on swelling, compression property and degradation stability of PVA composite hydrogels for artificial nucleus pulposus.

Artificial nucleus pulposus (ANP) replacement as an alternative to the treatment of cervical spondylosis aims to relieve pain and restore the normal cervical motion. In this study, the PVA/PVP and PVA/Pectin composite hydrogels (CH)s with different concentrations were prepared by the freezing-thawing process, and their performances were tested. The effect of different concentrations on both kinds of PVA CHs were evaluated and analysed. The results demonstrated that both kinds of CHs had good swelling property (¿190%), compressive stress-strain characteristic response and stable performance, and they were not easy to degrade (¡9%). The elastic modulus of the PVA/PVP CH was close to that of nucleus pulposus prosthesis, and the weight loss ratio of the PVA/PVP CH was lower than that of PVA/Pectin CH under load condition. Further, the experimental results showed that the PVA/PVP CH with 15 wt% solute and 1 wt% PVP content had the best comprehensive performance, which may provide significant advantages for use in future clinical application in replacing nucleus pulposus.

Elastic shell theory for plant cell wall stiffness reveals contributions of cell wall elasticity and turgor pressure in AFM measurement.

The stiffness of a plant cell in response to an applied force is determined not only by the elasticity of the cell wall but also by turgor pressure and cell geometry, which affect the tension of the cell wall. Although stiffness has been investigated using atomic force microscopy (AFM) and Young's modulus of the cell wall has occasionally been estimated using the contact-stress theory (Hertz theory), the existence of tension has made the study of stiffness more complex. Elastic shell theory has been proposed as an alternative method; however, the estimation of elasticity remains ambiguous. Here, we used finite element method simulations to verify the formula of the elastic shell theory for onion (Allium cepa) cells. We applied the formula and simulations to successfully quantify the turgor pressure and elasticity of a cell in the plane direction using the cell curvature and apparent stiffness measured by AFM. We conclude that tension resulting from turgor pressure regulates cell stiffness, which can be modified by a slight adjustment of turgor pressure in the order of 0.1 MPa. This theoretical analysis reveals a path for understanding forces inherent in plant cells.

A lightweight strain glass alloy showing nearly temperature-independent low modulus and high strength.

Fast development of space technologies poses a strong challenge for elastic materials, which need to be not only lightweight, strong and compliant, but also able to maintain stable elasticity over a wide temperature range1-4. Here we report a lightweight magnesium-scandium strain glass alloy (Mg with 21.3 at.% Sc) that meets this challenge. This alloy is as light (density ~2 g cm-3) and compliant as organic-based materials5-7 like bones and glass fibre reinforced plastics, but in contrast with those materials, it possesses a nearly temperature-independent (or Elinvar-type), ultralow Young's modulus (~20-23 GPa) over a wide temperature range from room temperature down to 123 K; a higher yield strength of ~200-270 MPa; and a long fatigue life of over one million cycles. As a result, it exhibits a relatively high, temperature-independent elastic energy density of ~0.5 kJ kg-1 among known materials at a moderate stress level of 200 MPa. We show that its exceptional properties stem from a strain glass transition, and the Elinvar-type elasticity originates from its moderate elastic softening effect cancelling out the ever-present elastic hardening. Our findings provide insight into designing materials that possess unconventional and technologically important elastic properties.

Photobiomodulation Therapy Affects the Elastic Modulus, Cytoskeletal Rearrangement and Migration Capability of Human Osteosarcoma Cells.

Photobiomodulation (PBM) therapy utilizes low-power lasers to modulate the viability of living human cells and leads to changes in proliferation, differentiation, adhesion and gene expression, even though the rearrangement of cytoskeleton was not previously studied. The present study aims to evaluate the photobiological effects on the elastic behavior of human osteosarcoma cells (MG-63) and their morphological changes. Fluorescence staining, confocal imaging and atomic force microscopy (AFM) topography were performed to study the effects of PBM therapy with the exposure of 532 nm-25mW, 650 nm-3mW, 650 nm-150mW and 780 nm-70mW beams following the 5-min continuous irradiation. The area of each beam was 3.14cm2 with a source-surface distance of 20 cm. Besides the cell proliferation assessment, the migratory potential of MG-63 was determined with the wound healing technique. The results indicated an increase in stiffness and shape index of radiation-induced cells 24 h after exposure along with the obvious F-actins changes. But, cell stiffening was not observed 72 h after 532 nm laser irradiation. Also, a decrease in the migration rate was seen in all of the groups after 72 h of irradiation except cells treated with 532 nm wavelength. However, 532 nm laser beams increase the migratory potential 24 h after exposure. Within 72 h after irradiation, the cell proliferation was only affected by applying 532 nm and 650 nm-150mW laser beams. It was concluded that applying photobiomodulation with wavelengths of 650 nm (at both utilized powers) and 780 nm alters the migration capability and provides a quantitative description of cytoskeletal changes. Moreover, membrane stiffening can be considered as the biological marker of PBM treatments.

Atomic Force Microscopy (AFM) Applications in Arrhythmogenic Cardiomyopathy.

Arrhythmogenic cardiomyopathy (ACM) is an inherited heart muscle disorder characterized by progressive replacement of cardiomyocytes by fibrofatty tissue, ventricular dilatation, cardiac dysfunction, arrhythmias, and sudden cardiac death. Interest in molecular biomechanics for these disorders is constantly growing. Atomic force microscopy (AFM) is a well-established technic to study the mechanobiology of biological samples under physiological and pathological conditions at the cellular scale. However, a review which described all the different data that can be obtained using the AFM (cell elasticity, adhesion behavior, viscoelasticity, beating force, and frequency) is still missing. In this review, we will discuss several techniques that highlight the potential of AFM to be used as a tool for assessing the biomechanics involved in ACM. Indeed, analysis of genetically mutated cells with AFM reveal abnormalities of the cytoskeleton, cell membrane structures, and defects of contractility. The higher the Young's modulus, the stiffer the cell, and it is well known that abnormal tissue stiffness is symptomatic of a range of diseases. The cell beating force and frequency provide information during the depolarization and repolarization phases, complementary to cell electrophysiology (calcium imaging, MEA, patch clamp). In addition, original data is also presented to emphasize the unique potential of AFM as a tool to assess fibrosis in cardiac tissue.

Comparative effect of lumbar myofascial release with electrotherapy on the elastic modulus of lumbar fascia and pain in patients with non-specific low back pain.

OBJECTIVES: Low back pain is a major health issue in most industrialized countries. Lumbar fascia is supported as a potential source of pain in the lumbar region. Myofascial release is a manual therapeutic approach that focuses on restoring altered soft tissue function. On the other hand, one of the most commonly used physical therapy methods for low back pain is electrotherapy. The purpose of this study was to compare the effect of lumbar Myofascial release and electrotherapy on clinical outcomes of Non-specific low back pain and elastic modulus of lumbar myofascial tissue. DESIGN: Randomized, clinical trial. SETTING: Outpatient Low back pain clinic. SUBJECTS: 32 subjects with low back pain. INTERVENTIONS: Subjects were randomized into the myofascial release group (n = 16) and electrotherapy group(n = 16). Subjects in the myofascial release group received 4 sessions of myofascial release in the lumbar region, and the electrotherapy group received 10 sessions of electrotherapy. MAIN MEASURES: Low back pain severity, and elastic modulus of the lumbar myofascial tissue were assessed before and after treatment. RESULTS: An independent sample T-test was used to compare baseline variables in both groups (p > 0.05) (effect size≥0.83), Paired T-test was used to compare within-group changes after performing myofascial release and electrotherapy (p ≤ 0.023) (effect size≥0.56), and the GLM Anova test was used to Comparison of Changes in the Elastic Modulus of the Lumbar Spine and Low Back Pain between-group (F (10,21) = 12.10, P < 0.0005) (effect size = 0.86). CONCLUSION: The improvements in the outcome measures suggest that lumbar myofascial release may be effective in subjects with non-specific low back pain. Data suggest that the elastic modulus of lumbar fascia and the severity of low back pain are directly linked. Decreasing the elastic modulus after myofascial release can directly affect reducing low back pain.

Thermal therapy induced fluid pressure and stress reductions in a solid tumor.

This paper presents an investigation on the interstitial fluid pressure and stress reductions in a vascularized solid tumor using a thermal therapy approach. The solid tumor is modeled as a fluid infiltrated poroelastic medium with a pressure source subjected to spatial heating. The distributions of temperature, interstitial fluid pressure, strains and stresses in a spherical tumor are obtained using a thermoporoelasticity theory in which the extracellular solid matrix and the interstitial fluid have different coefficient of thermal expansion (CTE). The numerical results for a solid tumor subjected to uniform spatial heating indicate that the CTE of the solid matrix of the tumor plays a crucial role in the reductions in the fluid pressure and effective stresses caused by the thermal therapy. The pore pressure and effective stresses are reduced when the CTE of the solid matrix is higher than that of the interstitial fluid. The reductions in fluid pressure and stresses may become significant depending on the difference between the CTEs of the solid matrix and interstitial fluid. The reductions reach the maximum at the tumor center and decrease with increasing radial distance from the tumor center. Finally, the thermally induced fluid flow is directed from the surface towards the center thereby potentially improving the microcirculation in the solid tumor.

Characterization of Chlorhexidine-Impregnated Cellulose-Based Hydrogel Films Intended for the Treatment of Periodontitis.

Periodontitis comprises a chronic inflammation that is initiated by microbiota biofilm. If left untreated, periodontitis may lead to permanent tooth loss. Herein, we propose to design and improve a localized form of therapy comprising a chlorhexidine-impregnated hydrogel. Hydrogel films were prepared by varying the ratio between cellulose (MCC) and carboxymethylcellulose sodium (CMC) using the crosslinker epichlorohydrin (ECH). The hydrogel was loaded with chlorhexidine. Increasing the CMC ratio led to a reduction in the number of pores, an increase in their size, lower glass transition temperature (T g ), decreased Young's modulus, and increased film stretching and affected the time of release. Bacterial and fungal zones of inhibition showed similar activity and were not affected by the CMC and MCC ratio. Hydrogels loaded with chlorhexidine prevented the growth of S. oralis and C. albicans microorganisms and may provide a promising local delivery system for treating periodontitis.

Mechanical Anisotropy in Two-Dimensional Selenium Atomic Layers.

Two-dimensional (2D) trigonal selenium (t-Se) has become a new member in 2D semiconducting nanomaterial families. It is composed of well-aligned one-dimensional Se atomic chains bonded via van der Waals (vdW) interaction. The contribution of this unique anisotropic nanostructure to its mechanical properties has not been explored. Here, for the first time, we combine experimental and theoretical analyses to study the anisotropic mechanical properties of individual 2D t-Se nanosheets. It was found that its fracture strength and Young's modulus parallel to the atomic chain direction are much higher than along the transverse direction, which was attributed to the weak vdW interaction between Se atomic chains as compared to the covalent bonding within individual chains. Additionally, two distinctive fracture modes along two orthogonal loading directions were identified. This work provides important insights into the understanding of anisotropic mechanical behaviors of 2D semiconducting t-Se and opens new possibilities for future applications.

Fourier Transform Infrared Microspectroscopy Combined with Principal Component Analysis and Artificial Neural Networks for the Study of the Effect of ß-Hydroxy-ß-Methylbutyrate (HMB) Supplementation on Articular Cartilage.

The potential of Fourier Transform infrared microspectroscopy (FTIR microspectroscopy) and multivariate analyses were applied for the classification of the frequency ranges responsible for the distribution changes of the main components of articular cartilage (AC) that occur during dietary ß-hydroxy-ß-methyl butyrate (HMB) supplementation. The FTIR imaging analysis of histological AC sections originating from 35-day old male piglets showed the change in the collagen and proteoglycan contents of the HMB-supplemented group compared to the control. The relative amount of collagen content in the superficial zone increased by more than 23% and in the middle zone by about 17%, while no changes in the deep zone were observed compared to the control group. Considering proteoglycans content, a significant increase was registered in the middle and deep zones, respectively; 62% and 52% compared to the control. AFM nanoindentation measurements collected from animals administered with HMB displayed an increase in AC tissue stiffness by detecting a higher value of Young's modulus in all investigated AC zones. We demonstrated that principal component analysis and artificial neural networks could be trained with spectral information to distinguish AC histological sections and the group under study accurately. This work may support the use and effectiveness of FTIR imaging combined with multivariate analyses as a quantitative alternative to traditional collagenous tissue-related histology.

Hybrid donor-acceptor polymer nanoparticles and combination antibiotic for mitigation of pathogenic bacteria and biofilms.

Biofilms pose a significant clinical problem in skin and soft tissue infections. Their resistance to antibiotics has spurred investigations into alternative treatments, such as nanoparticle-mediated photothermal ablation. Non-toxic Hybrid Donor- Acceptor (DA) Polymer nanoParticles (H-DAPPs) were developed for fluorescence imaging (using poly(3-hexylthiophene-2,5 diyl) (P3HT)) and rapid, near-infrared photothermal ablation (NIR- PTA) (using poly[4,4-bis(2-ethylhexyl)-cyclopenta[2,1-b;3,4-b']dithiophene-2,6-diyl-alt-2,1,3-benzoselenadiazole-4,7-diyl] (PCPDTBSe)). H-DAPPs were evaluated alone, and in combination with antibiotics, against planktonic S. aureus and S. pyogenes, and S. aureus biofilms. H-DAPPs NIR-PTA (15-700 µg/ mL) can generate rapid temperature changes of 27.6-73.1 °C, which can eradicate planktonic bacterial populations and reduce biofilm bacterial viability by more than 4- log (> 99.99%) with exposure to 60 s of 800 nm light. Reductions were confirmed via confocal analysis, which suggested that H-DAPPs PTA caused bacterial inactivation within the biofilms, but did not significantly reduce biofilm polysaccharides. SEM imaging revealed structural changes in biofilms after H-DAPPs PTA. S. aureus biofilms challenged with 100 µg/mL of H-DAPPs (H-DAPPs-100) to induce an average temperature of 55.1 °C, and the minimum biofilm eradication concentration (MBEC) of clindamycin, resulted in up to ~3- log decrease in bacterial viability compared to untreated biofilms and those administered H-DAPPs-100 PTA only, and up to ~2- log compared to biofilms administered only clindamycin. This study demonstrates that polymer nanoparticle PTA can mitigate biofilm infection and may improve antimicrobial efficacy.

Characterization and Physical and Biological Properties of Tissue Conditioner Incorporated with Carum copticum L.

AIM: One of the main problems in dentistry is the injury caused by the long-term application of an ill-fitting denture. The existence of multiple microorganisms along with the susceptibility of the tissue conditioners to colonize them can lead to denture stomatitis. This study is aimed at developing a tissue conditioner incorporated with Carum copticum L. (C. copticum L.) for the effective treatment of these injuries. MATERIALS AND METHODS: The Carum copticum L. essential oil composition was determined by gas chromatography-mass (GC-mass) spectrometry. The antimicrobial activity of the essential oil against the standard strains of bacterial and fungal species was determined by broth microdilution methods as suggested by the Clinical and Laboratory Standards Institute (CLSI). The physical and chemical properties of the prepared tissue conditioner were investigated by viscoelasticity, FTIR assays, and the release study performed. Furthermore, the antibiofilm activity of the Carum copticum L. essential oil-loaded tissue conditioner was evaluated by using the XTT reduction assay and scanning electron microscopy (SEM). RESULTS: The main component of the essential oil is thymol, which possesses high antimicrobial activity. The broth microdilution assay showed that the essential oil has broad activity as the minimum inhibitory concentration was in the range of 32-128 µg mL-1. The viscoelasticity test showed that the essential oil significantly diminished the viscoelastic modulus on the first day. The FTIR test showed that Carum copticum L. essential oil was preserved as an independent component in the tissue conditioner. The release study showed that the essential oil was released in 3 days following a sustained release and with an ultimate cumulative release of 81%. Finally, the Carum copticum L. essential oil exhibited significant activity in the inhibition of microbial biofilm formation in a dose-dependent manner. Indeed, the lowest and highest amounts of biofilm formation on the tissue conditioner disks are exhibited in the Streptococcus salivarius and Candida albicans by up to 22.4% and 71.4% at the 64 µg mL-1 concentration of C. copticum L. with a statistically significant difference (P < 0.05). CONCLUSION: The obtained results showed that the Carum copticum L. essential oil-loaded tissue conditioner possessed suitable physical, biological, and release properties for use as a novel treatment for denture stomatitis.

Understanding the aggregation structure, digestive and rheological properties of corn, potato, and pea starches modified by ultrasonic frequency.

Corn starch (CS), potato starch (PtS), and pea starch (PS) were modified by ultrasonic frequency (codes as UFCS, UFPtS and UFPS), and changes in aggregation structure, digestibility and rheology were investigated. For UFCS, the apparent amylose content and gelatinization enthalpy (∆H) decreased, while the R1047/1022 values and relative crystallinity (RC) increased under lower ultrasonic frequencies (20 kHz and 25 kHz). For UFPtS, the apparent amylose content, R1047/1022 values and RC increased, while the ∆H decreased under a higher ultrasonic frequency (28 kHz). For UFPS, the apparent amylose content, R1047/1022 values, RC, ∆H decreased at 20 kHz, 25 kHz and 28 kHz. Cracks were observed on the surface of UFCS, UFPtS and UFPS. These aggregation structure changes increased the resistant starch content to 31.11% (20 kHz) and 26.45% (25 kHz) for UFCS and to 39.68% (28 kHz) for UFPtS, but decreased the resistant starch content to 18.46% (28 kHz) for UFPS. Consistency coefficient, storage modulus, and loss modulus of UFCS, UFPtS and UFPS increased, while the flow behavior index and damping factor decreased. Results indicated that CS, PtS and PS had diverse digestion and rheology behaviors after ultrasonic frequency modification, which fulfilled different demands in starch-based products.

Hamstring strains in professional rugby players result in increased fascial stiffness without muscle quality changes as assessed using shear wave elastography.

INTRODUCTION: Hamstring strain injury is common among sports injuries. A previous history of this injury is considered a strong predictor of recurrent hamstring strain injury. Fascial tissue reportedly becomes stiffer after hamstring strain injury. However, the association between fascial stiffness and previous hamstring strain injury has not been investigated in clinical studies. We aimed to determine whether a previous history of hamstring strain injury affects fascial tissue and muscle tissues using shear wave elastography. METHOD: In eleven male professional rugby players, the stiffness as a shear modulus (kPa) of fascial tissue and muscle was measured on the specific injured area measured by magnetic resonance imaging (MRI) at resting position by using shear wave elastography. The side-to-side differences between the injured and the uninjured side were analyzed. The length and area of the muscle scar tissue were evaluated by MRI in relation to fascial stiffness. RESULTS: The shear elastic modulus of fascia was stiffer in the injured vs. the uninjured side; however, no difference was observed in the muscle. No significant relationship was detected between the length and area of the muscle scar tissue (all P > 0.05). DISCUSSION: Rugby players with a previous history of hamstring strain injury exhibited passive stiffness of fascial tissues in the injured leg, regardless of the length or area of the muscle scar tissue. However, the passive stiffness of muscles was same between the injured and the uninjured leg. CONCLUSION: The results can be beneficial to consider future risk for hamstring strain injuries.

Adhesive performance enhancement of the mushroom-shaped microstructured elastomer by atmospheric plasma treatment.

Bioinspired reversible adhesives that have been developed in the course of recent years have found several applications in robotics, transportation, and marine applications. One of their prominent features is strong reversible static adhesion. To fulfill the requirements of various applications, the static adhesive performance of these materials can be enhanced by modifying the material and surface properties. In this work, the mushroom-shaped adhesive microstructured surface was functionalized by atmospheric plasma treatment to enhance its adhesive performances. Through optimizing the duration of the treatment, the pull-off force increase of up to 60% can be reached after the treatment in comparison to the measurements performed on the same mushroom-shaped microstructured sample before the treatment. In comparison to the microstructured samples, the attachment of the unstructured sample made of the same silicone elastomer was enhanced by 16% after plasma treatment. The strong adhesion enhancement on the microstructured sample was attributed to the combination of the changed effective elastic modulus of the material and the specific detachment behavior of microstructures. These results are anticipated to contribute to the further development of bioinspired dry adhesives and may potentially widen their usage in various technological applications.

Response surface methodology-based improvement of the yield and differentiation of properties of bacterial cellulose by metabolic enhancers.

This study aims to examine the effect of ethanol and lactic acid on the production of bacterial cellulose, and determine the optimal composition of a co-supplemented culture using response surface methodology. Both ethanol and lactic acid, when added separately or jointly, affected the yield and properties of the biomaterial. Optimization resulted in an increase of 470% in the yield, compared to the Schramm-Hestrin medium. Culture growth profiles, substrate consumption and by-products generation, were examined. The growth rate was increased for cultures supplemented with lactic acid and both lactic acid and ethanol, while the production of gluconic acid was diminished for all modified cultures. The properties of BNC, such as the structure, crystallinity, water holding capacity and tensile strength, were also determined. BNC produced in optimal conditions is more porous and characterized by wider fibers. Despite a decrease in crystallinity, by the addition of ethanol, lactic acid and both additives, the ratio of cellulose Iα was almost unchanged. The stress, strain, young modulus and toughness were improved 2.8-4.2 times, 1-1.9 times, 2.4-3.5 times and 2.5-6.8 times, respectively. The new approach to improving BNC yields and properties presented here could contribute to more economical production and wider application of this biopolymer.

Evaluation of easy-removing antioxidant films of chitosan with Melaleuca alternifolia essential oil.

Chitosan - tea tree essential oil (TTEO) films were obtained as a new biodegradable material. Malic acid or lactic acid solvents were evaluated to obtain easy-removing films. The microstructure by SEM and FT-IR, the thermal properties by TGA/DSC, the mechanical properties, the water vapor permeability, the antioxidant (DPPH• and ABTS•+) activity and the optical properties of the formulated films were evaluated. A complete dissolution of the film in water was obtained. The elongation to break was higher in the films with malic acid (145.88-317.33%), comparing with those with lactic acid (25.54-44.08%). Chitosan film obtained in malic acid with TTEO showed the highest antioxidant activity. The colour and transparency of the samples did not suffer significant variations by TTEO addition. Films showed good UV-barrier properties, with a slightly improvement by TTEO addition. The films obtained showed a great potential for food packaging applications.

Potato starch altered the rheological, printing, and melting properties of 3D-printable fat analogs based on inulin emulsion-filled gels.

Plant-based oil inks that imitate the texture and melting behavior of traditional animal fats using 3D printing have been developed. The influence of the incorporation of potato starch and the type of oil on rheology and meltability was investigated. The results showed that the dynamic modulus and hardness of fat analogs increased, whereas fat analog meltability decreased with an increase in potato starch content. Coconut oil and soybean oil-containing fat analogs incorporated with proper potato starch levels exhibited good printability and similar meltability to commercial beef and pork fats. The addition of potato starch suppressed fat analog meltability as it disrupted the inulin matrix. Fat analogs containing coconut oil could be texturized at temperatures lower than those required for their soybean oil counterparts. The fat analogs were solid at room temperature, demonstrated good printability, and imitated the melting behavior of fat contained in real meat throughout the cooking process.

Pectin-organophilized ZnO nanoparticles as sustainable fillers for high-density polyethylene composites.

A series of nanocomposites made of high-density polyethylene (HDPE) and 10 wt% zinc oxide nanoparticles (ZnO NPs) were produced by extrusion and injection molding. The nanoparticles were prepared via a green way using the pectin-based banana peel extract as the stabilizer and a proper dispersion-providing agent. The fillers were well-dispersed in the matrix and the composites exhibited improved functional characteristics such as increased thermal stability and mechanical properties. The presence of the pectin-organophilized filler had a significant impact on the crystallization process of HDPE. The kinetics of the degradation process was also altered in comparison to the pure polymer. The fire properties of the composites were enhanced as the amount of the gas products produced during their degradation was reduced, what was confirmed by thermogravimetric analysis coupled with gas products analyses (TGA/FTIR/QMS). The structure and morphology of the materials were characterized by scanning electron microscope (SEM), infrared spectroscopy (FTIR), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). Additionally, the mechanical properties were tested by tensile tests. An in-depth analysis revealed that the HDPE-pectin-ZnO interactions are crucial for the structural and performance properties of the final composite. The used biopolymer reacts with ZnO via ionic interaction and through hydrogen bond in the case of HDPE.

PEG-crosslinked-chitosan hydrogel films for in situ delivery of Opuntia ficus-indica extract.

In the present study, chitosan-based wound dressings loaded with the extract of Opuntia ficus-indica (OPU) were prepared. OPU is known for its capability to accelerate skin injury repair. Chitosan (Ch) was crosslinked with a low molecular weight diepoxy-poly(ethylene glycol) (diePEG), and hydrogel films with different Ch/PEG composition and OPU content were prepared by casting. The occurrence of crosslinking reaction was confirmed by FTIR spectroscopy. FTIR and DSC analysis suggested that ionic interactions occur between chitosan and OPU. Tensile tests evidenced that the crosslinking caused a decrease of Young's modulus, which approaches the value of the human skin modulus. Swelling characteristics, water vapor transmission rate, and release kinetics demonstrated that these films are adequate for the proposed application. Finally, a scratch test on a keratinocytes monolayer showed that the rate of cell migration in the presence of OPU-loaded samples is about 3-fold higher compared to unloaded films, confirming the repairing activity of OPU.