Biodiesel Production by Methanolysis of Rapeseed Oil-Influence of SiO2/Al2O3 Ratio in BEA Zeolite Structure on Physicochemical and Catalytic Properties of Zeolite Systems with Alkaline Earth Oxides (MgO, CaO, SrO).

Alkaline earth metal oxide (MgO, CaO, SrO) catalysts supported on BEA zeolite were prepared by a wet impregnation method and tested in the transesterification reaction of rapeseed oil with methanol towards the formation of biodiesel (FAMEs-fatty acid methyl esters). To assess the influence of the SiO2/Al2O3 ratio on the catalytic activity in the tested reaction, a BEA zeolite carrier material with different Si/Al ratios was used. The prepared catalysts were tested in the transesterification reaction at temperatures of 180 °C and 220 °C using a molar ratio of methanol/oil reagents of 9:1. The transesterification process was carried out for 2 h with the catalyst mass of 0.5 g. The oil conversion value and efficiency towards FAME formation were determined using the HPLC technique. The physicochemical properties of the catalysts were determined using the following research techniques: CO2-TPD, XRD, BET, FTIR, and SEM-EDS. The results of the catalytic activity showed that higher activity in the tested process was confirmed for the catalysts supported on the BEA zeolite characterized by the highest silica/alumina ratio for the reaction carried out at a temperature of 220 °C. The most active zeolite catalyst was the 10% CaO/BEA system (Si/Al = 300), which showed the highest triglyceride (TG) conversion of 90.5% and the second highest FAME yield of 94.6% in the transesterification reaction carried out at 220 °C. The high activity of this system is associated with its alkalinity, high value of the specific surface area, the size of the active phase crystallites, and its characteristic sorption properties in relation to methanol.

Synthesis of struvite-enriched slow-release fertilizer using magnesium-modified biochar: Desorption and leaching mechanisms.

To improve the retention and slow-release abilities of nitrogen (N) and phosphorus (P), an 82 %-purity struvite fertilizer (MAP-BC) was synthesized using magnesium-modified biochar and a solution with a 2:1 concentration ratio of NH4+ to PO43- at a pH of 8. Batch microscopic characterizations and soil column leaching experiments were conducted to study the retention and slow-release mechanisms and desorption kinetics of MAP-BC. The slow-release mechanism revealed that the dissolution rate of high-purity struvite was the dominant factor of NP slow release. The re-adsorption of NH4+ and PO43- by biochar and unconsumed MgO prolonged slow release. Mg2+ ionized by MgO could react with PO43- released from struvite to form Mg3(PO4)2. The internal biochar exhibited electrostatic attraction and pore restriction towards NH4+, while magnesium modification and nutrient loading formed a physical antioxidant barrier that ensured long-term release. The water diffusion experiment showed a higher cumulative release rate for PO43- compared to NH4+, whereas in soil column leaching, the trend was reversed, suggesting that soil's competitive adsorption facilitated the desorption of NH4+ from MAP-BC. During soil leaching, cumulative release rates of NH4+ and PO43- from chemical fertilizers were 3.55-3.62 times faster than those from MAP-BC. The dynamic test data for NH4+ and PO43- in MAP-BC fitted the Ritger-Peppas model best, predicting release periods of 163 days and 166 days, respectively. The leaching performances showed that MAP-BC reduced leaching solution volume by 5.58 % and significantly increased soil large aggregates content larger than 0.25 mm by 24.25 %. The soil nutrients retention and pH regulation by MAP-BC reduced leaching concentrations of NP. Furthermore, MAP-BC significantly enhanced plant growth, and it is more suitable as a NP source for long-term crops. Therefore, MAP-BC is expected to function as a long-term and slow-release fertilizer with the potential to minimize NP nutrient loss and replace part of quick-acting fertilizer.

Novel yellowish-green single-phased spinel Mg1-xBaxAl2O4:Mn2+ phosphor(s) for color rendering white-light-emitting diodes.

For white light-rendering research activities, interpretation by using colored emitting materials is an alternative approach. But there are issues in designing the white color emitting materials. Particularly, differences in thermal and decay properties of discrete red, green, and blue emitting materials led to the quest for the search of a single-phased material, able to emit primary colors for white light generation. The current study is an effort to design a simple, single-phase, and cost-effective material with the tunable emission of primary colors by a series of Mg1-xBaxAl2O4:Mn2+ nanopowders. Doping of manganese ion (Mn2+) in the presence of the larger barium cation (Ba2+) at tetrahedral-sites of the spinel magnesium aluminate (MgAl2O4) structure led to the creation of antisite defects. Doped samples were found to have lower bandgaps compared with MgAl2O4, and hybridization of 3d-orbitals of Mn2+ with O(2p), Mg(2s)/Al(2s3p) was found to be responsible for narrowing the bandgap. The distribution of cations at various sites at random results in a variety of electronic transitions between the valance band and oxygen vacancies as well as electron traps produced the antisite defects. The suggested compositions might be used in white light applications since they have three emission bands with centers at 516 nm (green), 464 nm (blue) and 622 nm (red) at an excitation wavelength of 380 nm. A detailed discussion to analyze the effects of the larger cationic radius of Ba2+ on the lattice strain, unit cell parameters, and cell volumes using X-ray diffraction analysis is presented.

Peroxymonosulfate activation by nanocomposites towards the removal of sulfamethoxazole: Performance and mechanism.

Heterogeneous activation of peroxomonosulfate (PMS) has been extensively studied for the degradation of antibiotics. The cobalt ferrite spinel exhibits good activity in the PMS activation, but suffers from the disadvantage of low PMS utilization efficiency. Herein, the nanocomposites including FeS, CoS2, CoFe2O4 and Fe2O3 were synthesized by hydrothermal method and used for the first time to activate PMS for the removal of sulfamethoxazole (SMX). The nanocomposites showed superior catalytic activity in which the SMX could be completely removed at 40 min, 0.1 g L-1 nanocomposites and 0.4 mM PMS with the first order kinetic constant of 0.2739 min-1. The PMS utilization efficiency was increased by 29.4% compared to CoFe2O4. Both radicals and non-radicals contributed to the SMX degradation in which high-valent metal oxo dominated. The mechanism analysis indicated that sulfur modification, on one hand, enhanced the adsorption of nanocomposites for PMS, and promoted the redox cycles of Fe2+/Fe3+ and Co2+/Co3+ on the other hand. This study provides new way to enhance the catalytic activity and PMS utilization efficiency of spinel cobalt ferrite.

Multiprocessing Substrates Enhanced Ta2O5/NiCo2O4 Spinel Nanocomposites for Effective Electro-/Photocatalytic and Toxicological Effects via the Caenorhabditis elegans Model.

NiCo2O4 spinel composites decorated with metal oxides (Ta2O5), reduced graphene oxide (rGO), polyaminoanthraquinone (PAAQ), and layered double hydroxide hydrotalcite (HTs) were synthesized by the hydrothermal route. The synthesized composites were characterized using X-ray powder diffraction (XRD), Brunauer-Emmett-Teller (BET), high-resolution transmission electron microscopy (HR-TEM), and X-ray photoelectron spectroscopy (XPS) analyses for structural parameters such as surface area, morphology, chemical composition, etc. The production of oxygen by the water oxidation technique is the most suitable eco-friendly method, where rGO@Ta2O5/NiCo2O4 (RTNCO) showed an efficient oxygen evolution reaction (OER) performance under 1 M KOH electrolyte. Lower Tafel slope and overpotential values of 76 mV dec-1 and 315 mV, respectively, were calculated for RTNCO. The photocatalytic degradation efficiencies calculated were MB = 97.86%, RhB = 94.75%, and AP = 96% under UV light illumination within 120 min. The degraded dye solution was tested on mung bean (Vigna radiata) plants to determine the toxicity of the dye solution after 15 days, and the results showed good seed germination similar to that in water as the control. The synthesized materials exhibited better antibacterial activity against Bacillus cereus, Staphylococcus aureus, Pseudomonas aeruginosa, and Escherichia coli. Interestingly, the toxicological effects of the degraded dyes and drug solutions were effectively studied in the Caenorhabditis elegans model. The overall results revealed that the synthesized composites are promising for electro-/photocatalytic and biological applications.

Inhibitory effects and mechanisms of phenolic compounds in rapeseed oil on advanced glycation end product formation in chemical and cellular models in vitro.

Sinapic acid (SA), canolol (CAO) and canolol dimer (CAO dimer) are the main phenolic compounds in rapeseed oil. However, their possible efficacy against glycation remains unclear. This study aims to explore the impacts of these substances on the formation of advanced glycation end products (AGEs) based on chemical and cellular models in vitro. Based on fluorescence spectroscopy results, three chemical models of BSA-fructose, BSA-methylglyoxal (MGO), and arginine (Arg)-MGO showed that SA/CAO/CAO dimer could effectively reduce AGE formation but with different abilities. After SA/CAO/CAO dimer incubation, effective protection against BSA protein glycation was observed and three different MGO adducts were formed. In MGO-induced HUVEC cell models, only CAO and CAO dimer significantly inhibited oxidative stress and cell apoptosis, accompanied by the regulation of the Nrf2-HO-1 pathway. During the inhibition, 20 and 12 lipid mediators were reversed in the CAO and CAO dimer groups compared to the MGO group.

Efficient removal of phosphorus and nitrogen from aquatic environment using sepiolite-MgO nanocomposites: preparation, characterization, removal performance, and mechanism.

Excessive phosphorus will lead to eutrophication in aquatic environment; the efficient removal of phosphorus is crucial for wastewater engineering and surface water management. This study aimed to fabricate a nanorod-like sepiolite-supported MgO (S-MgO) nanocomposite with high specific surface area for efficient phosphate removal using a facile microwave-assisted method and calcining processes. The impact of solution pH, adsorbent dosage, contact time, initial phosphate concentrations, Ca2+ addition, and N/P ratio on the phosphate removal was extensively examined by the batch experiments. The findings demonstrated that the S-MgO nanocomposite exhibited effective removal performance for low-level phosphate (0 ~ 2.0 mM) within the pH range of 3.0 ~ 10.0. Additionally, the nanocomposite can synchronously remove phosphate and ammonium in high-level nutrient conditions (> 2.0 mM), with the maximum removal capacities of 188.49 mg P/g and 89.78 mg N/g. Quantitative and qualitative analyses confirmed the successful harvesting of struvite in effluent with high-phosphate concentrations, with the mechanisms involved attributed to a synergistic combination of sorption and struvite crystallization. Due to its proficient phosphate removal efficiency, cost-effectiveness, and substantial removal capacity, the developed S-MgO nanocomposite exhibits promising potential for application in phosphorus removal from aquatic environments.

Fenton-like membrane reactor assembled by electron polarization and defect engineering modifying Co3O4 spinel for flow-through removal of organic contaminants.

The application of Fenton-like membrane reactors for water purification offers a promising solution to overcome technical challenges associated with catalyst recovery, reaction efficiency, and mass transfer typically encountered in heterogeneous batch reaction modes. This study presents a dual-modification strategy encompassing electron polarization and defect engineering to synthesize Al-doped and oxygen vacancies (OV)-enriched Co3O4 spinel catalysts (ACO-OV). This modification empowered ACO-OV with exceptional performance in activating peroxymonosulfate (PMS) for the removal of organic contaminants. Moreover, the ACO-OV@polyethersulfone (PES) membrane/PMS system achieved organic contaminant removal through filtration (with a reaction kinetic constant of 0.085 ms-1), demonstrating outstanding resistance to environmental interference and high operational stability. Mechanistic investigations revealed that the exceptional catalytic performance of this Fenton-like membrane reactor stemmed from the enrichment of reactants, exposure of reactive sites, and enhanced mass transfer within the confined space, leading to a higher availability of reactive species. Theoretical calculations were conducted to validate the beneficial intrinsic effects of electron polarization, defect engineering, and the confined space within the membrane reactor on PMS activation and organic contaminant removal. Notably, the ACO-OV@PES membrane/PMS system not only mineralized the targeted organic contaminants but also effectively mitigated their potential environmental risks. Overall, this work underscores the significant potential of the dual-modification strategy in designing spinel catalysts and Fenton-like membrane reactors for efficient organic contaminant removal.

Development of natural attapulgite derived ferromanganese spinel oxides as heterogeneous catalysts for persulfate activation of tetracycline degradation.

Ferromanganese spinel oxides (MnFe2O4, MFO) have been proven effective in activating persulfate for pollutants removal. However, their inherent high surface energy often leads to agglomeration, diminishing active sites and consequently restricting catalytic performance. In this study, using Al-MCM-41 (MCM) mesoporous molecular sieves derived from natural attapulgite as a support, the MFO/MCM composite was synthesized through dispersing MnFe2O4 nanoparticles on MCM carrier by a simple hydrothermal method, which can effectively activate persulfate (PS) to degrade Tetracycline (TC). The addition of Al-MCM-41 can effectively improve the specific surface area and adsorption performance of MnFe2O4, but also reduce the leaching amount of metal ions. The MFO/MCM composite exhibited superior catalytic reactivity towards PS and 84.3% removal efficiency and 64.7% mineralization efficiency of TC (20 mg/L) was achieved in 90 min under optimized conditions of 0.05 mg/L catalyst dosage, 5 mM PS concentration, room temperature and no adjustment of initial pH. The effects of various stoichiometric MFO/MCM ratio, catalyst dosage, PS concentration, initial pH value and co-existing ions on the catalytic performance were investigated in detail. Moreover, the possible reaction mechanism in MFO-MCM/PS system was proposed based on the results of quenching tests, electron paramagnetic resonance (EPR) and XPS analyses. Finally, major degradation intermediates of TC were detected by liquid chromatography mass spectrometry technologies (LC-MS) and four possible degradation pathways were proposed. This study enhances the design approach for developing highly efficient, environmentally friendly and low-cost catalysts for the advanced treatment process of antibiotic wastewater.

High efficiency adsorption of uranium by magnesia-silica-fluoride co-doped hydroxyapatite.

Hydroxyapatite has a high affinity to uranium, and element doping can effectively improve its adsorption performance. In this study, magnesia-silica-fluoride co-doped hydroxyapatite composite was prepared by hydrothermal method, and the effect of single-phase and multiphase doping on the structure and properties of the composites was investigated. The results showed that the specific surface area of Mg-Si-F-nHA composites increased by 63.01% after doping. Comparing with nHA, U(VI) adsorption capacity of Si-nHA, Mg-Si-nHA and Mg-Si-F-nHA composites increased by 13.01%, 17.39% and 22.03%, respectively. The adsorption capacity of Mg-Si-F-nHA composite reached 1286.76 mg/g. Adsorbent dosage and pH obviously affected U(VI) adsorption, and the experimental data can be fitted well by PSO and Sips models. The physicochemical characterization before and after adsorption suggested that complexation, ion exchange and precipitation participated in uranium adsorption. In conclusion, different elements doping can effectively improve the uranium adsorption properties of hydroxyapatite composites.

Granulation of hydrometallurgically synthesized spinel lithium manganese oxide using cross-linked chitosan for lithium adsorption from water.

A drastic increase in demand for electric vehicles and energy storage systems increases lithium (Li) need as a critical metal for the 21st century. Lithium manganese oxides stand out among inorganic adsorbents because of their high capacity, chemical stability, selectivity, and affordability for lithium recovery from aqueous media. This study investigates using hydrometallurgically synthesized lithium manganese oxide (Li1.6Mn1.6O4) in granular form coated with cross-linked chitosan for lithium recovery from water. Characterization methods such as SEM, FTIR, XRD, and BET reveal the successful synthesis of the composite adsorbent. Granular cross-linked chitosan-coated and delithiated lithium manganese oxide (CTS/HMO) adsorbent demonstrated optimal removal efficiency of 86 % at pH 12 with 4 g/L of adsorbent dosage. The Langmuir isotherm at 25 °C, which showed monolayer adsorption with a maximum capacity of 4.94 mg/g, a better fit for the adsorption behavior of CTS/HMO. Adsorption was endothermic and thermodynamically spontaneous. Lithium adsorption followed the pseudo-first-order kinetic model.

Cationic regulation of specificity and activity of defective MCo2O4 nanozyme (M=Fe, Co, Ni, Cu) for colorimetric detection of caffeic acid.

Spinel oxide has great promise in constructing highly active nanozymes due to its tunable crystal structure. However, it still faces the problems of poor specificity and insufficient enzyme activity, which limits its application in the field of analysis. Herein, a series of transition metal spinel oxides were synthesized by cation regulation strategy, and their enzymatic activity and catalytic mechanism were analyzed. Interestingly, FeCo2O4, Co3O4 and NiCo2O4 had oxidase-like activity and peroxidase-like activity, while CuCo2O4 had specific and high oxidase-like activity. Their oxidase-like activities follow the order of FeCo2O4 < Co3O4 < NiCo2O4 < CuCo2O4, which is consistent with their cation radius. The smaller the cation radius of tetrahedral site, the more beneficial it is to increase the oxidase-like activity. The high oxidase-like activity of CuCo2O4 may be attributed to the production of 1O2, •O2- and •OH. EPR results showed the presence of abundant oxygen vacancies in CuCo2O4. Upon the introduction of EDTA, TMB color reaction fades because of oxygen vacancies elimination by EDTA, indicating that oxygen vacancies played an important role in the reaction. Based on the inhibition effect of caffeic acid on the high oxidase-like activity of CuCo2O4, a simple and sensitive caffeic acid colorimetric sensing platform was developed. The linear range for the detection of caffeic acid is 0.02-15 µM, with a detection limit as low as 13 nM. The constructed sensor enables the detection of caffeic acid in caffeic acid tablets and actual water samples, providing a new strategy for the detection of caffeic acid and drug quality control.

Efficient removal and transformation of Cr(VI) from alkaline wastewater to form a ferrochromium spinel multiphase via a modified ferrite process.

Chromium-containing wastewater causes serious environmental pollution due to the harmfulness of Cr(VI). The ferrite process is typically used to treat chromium-containing wastewater and recycle the valuable chromium metal. However, the current ferrite process is unable to fully transform Cr(VI) into chromium ferrite under mild reaction conditions. This paper proposes a novel ferrite process to treat chromium-containing wastewater and recover valuable chromium metal. The process combines FeSO4 reduction and hydrothermal treatment to remove Cr(VI) and form chromium ferrite composites. The Cr(VI) concentration in the wastewater was reduced from 1040 mg L-1 to 0.035 mg L-1, and the Cr(VI) leaching toxicity of the precipitate was 0.21 mg L-1 under optimal hydrothermal conditions. The precipitate consisted of micron-sized ferrochromium spinel multiphase with polyhedral structure. The mechanism of Cr(VI) removal involved three steps: 1) partial oxidation of FeSO4 to Fe(III) hydroxide and oxy-hydroxide; 2) reduction of Cr(VI) by FeSO4 to Cr(III) and Fe(III) precipitates; 3) transformation and growth of the precipitates into chromium ferrite composites. This process meets the release standards of industrial wastewater and hazardous waste and can improve the efficiency of the ferrite process for toxic heavy metal removal.

Withania somnifera root extract inhibits MGO-induced skin fibroblast cells dysfunction via ECM-integrin interaction.

ETHNOPHARMACOLOGICAL RELEVANCE: Withania somnifera (L.) Dunal, known as Ashwagandha, has long been used in traditional medicine in Ayurveda, India, a representative adaptogen. The main active constituents of W. somnifera are withanolides, and the root is often used as a medicine with a wide range of pharmacological activities, which can be used to treat insomnia, neurasthenia, diabetes mellitus and skin cancer. AIM OF THE STUDY: Whole-component qualitative and quantitative analyses were performed on W. somnifera. We explored the ameliorative effect of the adaptogen representative plant W. somnifera on the senescence events of MGO-injured fibroblasts and its action mechanism and verified the hypotheses that WS can inhibit the accumulation of AGEs and regulate the dynamic balance among the components of the ECM by modulating the expression of integrin ß1 receptor; as a result, WS maintains cellular behavioural and biological functions in a normal range and retards the aging of skin from the cellular level. MATERIALS AND METHODS: In this study, the components of WS were first qualitatively and quantitatively analysed by HPLC fingerprinting and LC-MS detection. Second, a model of MGO-induced injury of CML-overexpressing fibroblasts was established. ELISA was used to detect CML expression and the synthesis of key extracellular matrix ECM protein components COL1, FN1, LM5 and TNC synthesis; CCK-8 was used to detect cell viability; EDU was used to detect cell proliferation capacity; fluorescence was used to detect cell adhesion capacity; and migration assay were used to detect cell migration capacity; qRT-PCR was used to detect the regulatory pathway TGF-ß1 and MMP-2, MMP-9 in ECMs; immunofluorescence was used to detect the expression of ITGB1; and WB was used to detect the expression of COL1, FN1, LM5, Tnc, TGF-ß1, MMP-2, MMP-9 and ITGB1. RESULTS: In total, 27 active ingredients were analysed from WS, which mainly consisted of withanolide components, such as withaferin A and withanolide A. Based on the model of MGO-induced fibroblast senescence injury, WS significantly inhibited CML synthesis. By up-regulating the expression of integrin ß1, it upregulated the expression of the TGF-ß1 gene, which is closely related to the generation of ECMs, downregulated the expression of the MMP-2 and MMP-9 genes, which are closely related to the degradation of ECMs, maintained the dynamic balance of the four types of ECMs, and improved cell viability as well as proliferation, migration and adhesion abilities. CONCLUSIONS: WS can prevent cellular behavioural dysfunction and delay skin ageing by reducing the accumulation of CML, upregulating the expression of the ITGB1 receptor, maintaining the normal function of ECM-integrin receptor interaction and preventing an imbalance between the production and degradation of protein components of ECMs. The findings reported in this study suggest that WS as a CML inhibitor can modulate ECM-integrin homeostasis and has great potential in the field of aging retardation.

CuxMg1-xFe2O4-type spinels as potential oxygen carriers for waste wooden biomass combustion.

Waste wood biomass is considered a renewable energy source. Combining biomass combustion with emerging clean combustion technologies such as chemical looping combustion (CLC) can yield effective and affordable carbon capture and, consequently, lead to negative net emissions of greenhouse gases. Oxygen carrier (OC) is a crucial material in CLC technology that must exhibit certain properties, such as high durability, good chemical stability during numerous red-ox cycles and, important for the combustion of solid fuels, the capability of spontaneously releasing oxygen in a process referred to as chemical looping with oxygen uncoupling (CLOU). In this work, a series of nine CuxMg1-xFe2O4 spinel-based materials were synthetized and evaluated for the first time as potential OCs for a waste biomass combustion. Their properties, such as oxygen transport capacity and reactivity with biomass (wood chips) as a fuel, were evaluated in a function of temperature (900-1000 °C). Tested oxygen carriers were characterized with an excellent oxygen transport capacity in CLOU process (up to 2.78 wt%) and good reaction rates with the fuel (up to 1.19 wt. %/min), and regeneration rates (up to 3.8 wt. %/min). High conversion of the waste biomass was also achieved (98.9 %). Moreover, new findings revealed a strong positive effect of magnesium addition on mechanical strength (crushing strength > 4 N for samples with Mg content above 0.5).

Development of Magnesium Aluminate (MgAl2O4) Nanoparticles for refractory crucible application.

Ceramics are the oxides of metals and nonmetals with excellent compressive strength. Ceramics usually exhibit inert behavior at high temperatures. Magnesium aluminate (MgAl2O4), a member of the ceramic family, possesses a high working temperature up to 2000°C, low thermal conductivity, high strength even at elevated temperatures, and good corrosion resistance. Moreover, Magnesium Aluminate Nanoparticles (MANPs) can be used in the making of refractory crucible applications. This study focuses on the thermal behavior of Magnesium Aluminate Nanoparticles (MANPs) and their application in the making of refractory crucibles. The molten salt method is used to obtain MANPs. The presence of MANPs is seen by XRD peaks ranging from 66° to 67°. The determination of the smallest crystallite size of the sample is achieved by utilizing the Scherrer formula and is found to be 15.3 nm. The SEM micrographs provided further information, indicating an average particle size of 91.2 nm. At 600°C, DSC curves show that only 0.05 W/g heat flows into the material, and the TGA curve shows only 3% weight loss, which is prominent for thermal insulation applications. To investigate the thermal properties, crucibles of pure MANPs and the different compositions of MANPs and pure alumina are prepared. During the sintering, cracks appear on the crucible of pure magnesium aluminate. To explore the reason for crack development, tablets of MgAl2O4 are made and sintered at 1150°C. Ceramography shows the crack-free surfaces of all the tablets. Results confirm the thermal stability of MANPs at high temperatures and their suitability for melting crucible applications.

Enhancing the nitrogen and phosphorus content of faecal-derived biochar via adsorption and precipitation from human urine.

Urine diversion in toilets is a promising strategy to maximise nutrient recovery and produce low-cost urine-derived fertilisers. There are various methods for nutrient recovery from urine, including precipitation and adsorption onto porous media, such as biochars. This study uses faecal-derived biochars to produce and, for the first time, comprehensively characterise enriched biochar fertilisers with the addition of fully hydrolysed undiluted human urine. The evolution of urea hydrolysis and nutrient content during urine storage was initially investigated over a 6-month storage period and NH4+ adsorption mechanisms studied under varying biochar doses and NH4-N concentrations. The process was further optimised by adding MgO to induce precipitation reactions, enabling the combined recovery of NH4+ and P. For NH4+ adsorption, experimental data exhibited a good fit to both the Freundlich (R2 = 0.989) and Langmuir (R2 = 0.974) isotherm models and the rate of the reaction was well described by a pseudo 2nd order kinetics model (R2 = 0.988). The NH4+ uptake was rapid during the initial 2 h of the reaction and the adsorption process reached completion after 24 h. The NH4-N adsorption capacity of the faecal-derived biochar was 19.8 mg/g and the main adsorption mechanism identified was ion exchange (K+ ↔ NH4+), as confirmed by XRD and ICP-OES. The effect of different biochar doses (0, 25, 50, 100 g/L) and MgO addition scenarios (Mg:P = 0, 1.5, 4) on N and P recovery showed that the combination of MgO (Mg:P = 1.5) with the lower biochar dose (25 g/L) produced the most NP-rich fertiliser product which was easily separated from the urine. Faecal-derived biochar had a limited adsorption capacity for P, with precipitation being the main mechanism for P recovery. When MgO was added to urine, >98% of total P was recovered via precipitation of struvite/struvite-K and substituted hydroxyapatite, as identified via SEM-EDX. Faecal-derived biochar was a successful carrier to recover the P-containing precipitates and facilitate liquid-solid separation after treatment. The findings of this study provide proof-of concept for the systemic management of source separated human excreta and pave the way for the production of marketable waste-derived fertilisers from on-site sanitation systems.

Biotemplated fabrication of N/O co-doped porous carbon confined spinel NiFe2O4 heterostructured mimetics for triple-mode sensing of antioxidants and ameliorating packaging properties.

In this work, shrimp shell-derived magnetic NiFe2O4/N, O co-doped porous carbon nanozyme with superior oxidase (OXD)-like activity was prepared and used for colorimetric/photothermal/smartphone dual-signal triple-mode detection of antioxidants in fruits and beverages. The magnetic NiFe2O4/N, O co-doped porous carbon (MNPC) material was triumphantly fabricated using a combined in-situ surface chelation and pyrolysis method. The resultant MNPC composite exhibits a superior OXD-like activity, which can effectively oxidize 3,3',5,5'-tetramethylbenzidine (TMB) for yielding colorimetric/temperature dual-signal (CTDS) in absence of H2O2. This CTDS output sensor was successfully used for the determination of ascorbic acid and tannic acid. The proposed CTDS sensor with good specificity and high sensitivity can satisfy different on-site analysis requirements. Interestingly, the MNPC as a sustainable filler was further used for improving packaging properties of polyvinyl alcohol film. In short, this work offers a large-scale and cheap method to fabricate magnetic carbon-based nanozyme for monitoring antioxidants and ameliorating packaging properties.

Ultrahigh-porosity Ranunculus-like MgO adsorbent coupled with predictive deep belief networks: A transformative method for phosphorus treatment.

Phosphorus is a nonrenewable material with a finite supply on Earth; however, due to the rapid growth of the manufacturing industry, phosphorus contamination has become a global concern. Therefore, this study highlights the remarkable potential of ranunculus-like MgO (MO4-MO6) as superior adsorbents for phosphate removal and recovery. Furthermore, MO6 stands out with an impressive adsorption capacity of 596.88 mg/g and a high efficacy across a wide pH range (2-10) under varying coexisting ion concentrations. MO6 outperforms the top current adsorbents for phosphate removal. The process follows Pseudo-second-order and Langmuir models, indicating chemical interactions between the phosphate species and homogeneous MO6 monolayer. MO6 maintains 80 % removal and 96 % recovery after five cycles and adheres to the WHO and EUWFD regulations for residual elements in water. FT-IR and XPS analyses further reveal the underlying mechanisms, including ion exchange, electrostatic, and acid-base interactions. Ten machine learning (ML) models were applied to simultaneously predict multi-criteria (sorption capacity, removal efficiency, final pH, and Mg leakage) affected by 15 diverse environmental conditions. Traditional ML models and deep neural networks have poor accuracy, particularly for removal efficiency. However, a breakthrough was achieved by the developed deep belief network (DBN) with unparalleled performance (MAE = 1.3289, RMSE = 5.2552, R2 = 0.9926) across all output features, surpassing all current studies using thousands of data points for only one output factor. These captivating MO6 and DBN models also have immense potential for effectively applying in the real water test with error < 5 %, opening immense horizons for transformative methods, particularly in phosphate removal and recovery.

Bioactive compounds from the leaves of Maytenus ilicifolia Mart. ex Reissek: Inhibition of LDL oxidation, glycation, lipid peroxidation, target enzymes, and microbial growth.

ETHNOPHARMACOLOGICAL RELEVANCE: Maytenus ilicifolia Mart. ex Reissek, a medicinal plant used for treating gastritis, ulcers, and gastric disorders, possesses therapeutic properties attributed to diverse leaf compounds-terpenoids, alkaloids, flavonoids, phenols, and tannins, reflecting the ethnopharmacological knowledge of traditional users. AIMS OF THE STUDY: We aimed to assess the antioxidant and antiglycant capacities of Maytenus ilicifolia's ethanolic extract and organic fractions, identify bioactive compounds through HPLC-MS/MS analysis, and conduct phytochemical assessments. We also assessed their potential to inhibit digestive and cholinesterase enzymes, mitigate oxidation of human LDL and rat hepatic tissue, and examine their antimicrobial and cytotoxic properties. MATERIALS AND METHODS: Organic fractions (hexane - HF-Mi, dichloromethane - DMF-Mi, ethyl acetate - EAF-Mi, n-butanol - BF-Mi, and hydromethanolic - HMF-Mi) were obtained via liquid-liquid partitioning. Antioxidant (DPPH, FRAP, ORAC) and antiglycant (BSA/FRU, BSA/MGO, ARG/MGO/LDL/MGO models) capacities were tested. Phytochemical analysis employed HPLC-MS/MS. We also studied the inhibitory effects on α-amylase, acetylcholinesterase, butyrylcholinesterase, human LDL and rat hepatic tissue oxidation, antimicrobial activity, and cytotoxicity against RAW 264.7 macrophages. RESULTS: HPLC-ESI-MS/MS identified antioxidant compounds such as catechin, quercetin, and kaempferol derivatives. Ethanolic extract (EE-Mi) and organic fractions demonstrated robust antioxidant and antiglycant activity. EAF-Mi and BF-Mi inhibited α-amylase (2.42 µg/mL and 7.95 µg/mL) compared to acarbose (0.144 µg/mL). Most organic fractions exhibited ∼50% inhibition of acetylcholinesterase and butyrylcholinesterase, rivaling galantamine and rivastigmine. EAF-Mi, BF-Mi, and EE-Mi excelled in inhibiting lipid peroxidation. All fractions, except HMF-Mi, effectively countered LDL oxidation, evidenced by the area under the curve. These fractions protected LDL against lipid peroxidation. CONCLUSION: This study unveils Maytenus ilicifolia's ethanolic extract and organic fractions properties. Through rigorous analysis, we identify bioactive compounds and highlight their antioxidant, antiglycant, enzyme inhibition, and protective properties against oxidative damage. These findings underline its significance in modern pharmacology and its potential applications in healthcare.