[Cluster cases of malignant pleural mesothelioma in an oil factory]. / Cluster di casi di mesotelioma maligno della pleura in un oleificio.

BACKGROUND: The traditional occupational hazards of the productive cycle of oils are attributable to chemicals (use of solvents, pesticides and other agents), dusts, labour accidents (trauma, ignition, explosion), noise, manual lifting, work organization and hot-wet microclimate. The latest risk is due to the use of high temperatures (from 50 up to 250 degrees C) during the processes of extraction with solvent and refining. No cases are reported in literature of asbestos related disease in subjects who worked in oil factories. Nevertheless the structure and organization of the workplace, which is similar to that of sugar refineries, where cases of malignant mesothelioma have been described (moreover in workers employed in running and maintenance of the plants), led to the assumption that even in oil factories asbestos for the insulation of pipes and boilers could be present. OBJECTIVES: To describe 3 cases of Malignant Mesothelioma that occurred in workers of the same oil factory. METHODS: Since this occupational sector is not conventionally known for asbestos exposure the Local Health Unit and the Lombardy Mesothelioma Registry decided to investigate this industrial plant. RESULTS: Following examination of the archives of the Local Health Unit and inspection of the plant, an environmental asbestos contamination (pipes and boilers) was found. The 3 cases were defined as occupational disease and the required legal procedures were initiated. This underlines the importance of close cooperation with Local Health Units of occupational medicine and the Regional Mesothelioma Registry in the study and acknowledgment of cases which would otherwise not have been recognized, with consequent loss of precious information.

Treatment of MEK and toluene mixtures in biofilters: effect of operating strategy an performance during transient loading.

In recent years, biofiltration has been increasingly applied as an air pollution control technology to minimize or eliminate emissions of volatile organic compounds from industrial sources and environmental remediation activities. Although the ability of this technology to maintain high removal efficiency during relatively steady loading conditions has been well established for many waste streams, relatively little research has focused on development of operating strategies that could improve treatment performance during transient loading conditions typical of industrial operations. In the research described herein, two operating strategies were evaluated over a period of 295 days in biofilters treating a model waste gas stream containing a two-component mixture of methyl ethyl ketone (MEK) and toluene. One biofilter was operated as a sequencing batch biofilter (SBB), and the other was operated as a conventional continuous-flow biofilter (CFB). During "normal" steady loading conditions, the model waste stream contained MEK concentrations ranging from 80 to 89 ppmv and toluene concentrations ranging from 28 to 30 ppmv. Both biofilter operating strategies resulted in stable long-term performance with greater than 99% contaminant removal during these normal loading conditions. On a regular basis, the influent MEK and toluene concentrations were temporarily increased to five times the normal influent concentration for the duration of 1 h to test performance during transient "shock loading" conditions. Biofilter performance during the model shock loading conditions demonstrate that SBB operating strategies can result in superior treatment in two important areas: (1) overall mass of contaminants removed and (2) minimum instantaneous removal efficiency.

Effect of adding phosphate to drinking water on bacterial growth in slightly and highly corroded pipes.

The effect of phosphate addition in drinking water was tested under static conditions as batch tests and under dynamic conditions using continuously fed reactors. Phosphate supplements in batch tests from 0.1 to 2 mg P-PO4 L(-1) did not show any relationship between bacterial growth and phosphate concentration. Dynamic tests in slightly corroded reactor (stainless steel) treated at 1 mg P-PO4 L(-1) showed only a moderate improvement in the growth of microorganisms. On the contrary, phosphate treatment applied to the highly corroded reactor (unlined cast iron) led to an immediate, drastic drop in iron oxide release and bacterial production. Phosphate uptake by the reactor wall was less than 14% with the stainless-steel reactor and 70-90% with the corroded cast iron reactor. Moreover, about 5% of the phosphate associated to corroded iron pipe walls was released for 20 days after the end of treatment.

[Hygienic evaluation of hydrophobic turgid Perlite and the materials of powder composition used in water supply systems]. / Gigienicheskaia otsenka gidrofobnogo vspuchennogo perlita i izdenii iz poroshkovoi kompozitsii, ispo'lzuemykh v vodo- snabzhenii.

Sanitary, hygienic, toxicologic, pathomorphologic and genetic studies revealed that hydrophobic pearlites g A-1 and g A-2 and the material from powder composition of the brand of zh g p1, 5 d 2.5 had no unfavourable effect on physicochemical water characteristics, warm-blooded animals and poorly organized organisms. Hydrophobic pearlites were recommended for application in water reservoirs for the removal of petroleum films and the material from powder composition of the above brand for manufacturing cocks, sleeves, showers and other devices for water supply systems used for economic and drinking purposes.