Development of UV-Vis spectroscopy-based analysis method for determination of tin(IV) in epilobium parviflorum (hoary willowherb) tea using deep eutectic solvent based preconcentration.

In this study, a UV-Vis Spectroscopy-based method was developed for the determination of tin(IV) in epilobium parviflorum tea samples after preconcentration. The preconcentration process was carried out using the liquid-liquid microextraction technique. Before starting the analysis, optimization studies were carried out for the variables likely to affect the experimental results. As a result of the analyzes performed under optimum conditions, the detection limit of our method was calculated as 16.83 µg/L. The percent relative standard deviation value was calculated as 1.25% (n = 8) and linearity was found in the range of 10-1000 µg/L. Recovery experiments were performed on epilobium parviflorum tea samples using the matrix matching method. As a result of the analyzes made on teas belonging to three different brands, recovery results ranging from 92 to 117% were obtained.

Catalytic green synthesis of Tin(IV) oxide nanoparticles for phenolic compounds removal and molecular docking with EGFR tyrosine kinase.

In this study, tin dioxide nanoparticles (SnO2 NPs) were successfully synthesized through an eco-friendly method using basil leaves extract. The fabricated SnO2 NPs demonstrated significant adsorption capabilities for phenol (PHE), p-nitrophenol (P-NP), and p-methoxyphenol (P-MP) from water matrices. Optimal conditions for maximum removal efficiency was determined for each phenolic compound, with PHE showing a remarkable 95% removal at a 3 ppm, 0.20 g of SnO2 NPs, pH 8, and 30 min of agitation at 35 °C. Molecular docking studies unveiled a potential anticancer mechanism, indicating the ability of SnO2 NPs to interact with the epidermal growth factor receptor tyrosine kinase domain and inhibit its activity. The adsorption processes followed pseudo-second order kinetics and Temkin isotherm model, revealing spontaneous, exothermic, and chemisorption-controlled mechanisms. This eco-friendly approach utilizing plant extracts was considered as a valuable tool for nano-sorbent production. The SnO2 NPs not only exhibit promise in water treatment and also demonstrate potential applications in cancer therapy. Characterization techniques including scanning electron microscopy, UV-visible spectroscopy, Fourier transform infrared spectroscopy, X-ray diffraction spectroscopy (XRD), and energy-dispersive X-ray spectroscopy (EDAX) provided comprehensive insights into the results.

The interpretable machine learning model associated with metal mixtures to identify hypertension via EMR mining method.

There are limited data available regarding the connection between hypertension and heavy metal exposure. The authors intend to establish an interpretable machine learning (ML) model with high efficiency and robustness that identifies hypertension based on heavy metal exposure. Our datasets were obtained from the US National Health and Nutrition Examination Survey (NHANES, 2013-2020.3). The authors developed 5 ML models for hypertension identification by heavy metal exposure, and tested them by 10 discrimination characteristics. Further, the authors chose the optimally performing model after parameter adjustment by Genetic Algorithm (GA) for identification. Finally, in order to visualize the model's ability to make decisions, the authors used SHapley Additive exPlanation (SHAP) and Local Interpretable Model-Agnostic Explanations (LIME) algorithm to illustrate the features. The study included 19 368 participants in total. A best-performing eXtreme Gradient Boosting (XGB) with GA for hypertension identification by 16 heavy metals was selected (AUC: 0.774; 95% CI: 0.772-0.776; accuracy: 87.7%). According to SHAP values, Barium (0.02), Cadmium (0.017), Lead (0.017), Antimony (0.008), Tin (0.007), Manganese (0.006), Thallium (0.004), Tungsten (0.004) in urine, and Lead (0.048), Mercury (0.035), Selenium (0.05), Manganese (0.007) in blood positively influenced the model, while Cadmium (-0.001) in urine negatively influenced the model. Study participants' hypertension associated with heavy metal exposure was identified by an efficient, robust, and interpretable GA-XGB model with SHAP and LIME. Barium, Cadmium, Lead, Antimony, Tin, Manganese, Thallium, Tungsten in urine, and Lead, Mercury, Selenium, Manganese in blood are positively correlated with hypertension, while Cadmium in blood is negatively correlated with hypertension.

Combined exposure to multiple metals on hypertension in NHANES under four statistical models.

Metals exposure has gained increasing attention in the hypertension prevention. However, previous studies have focused on the impacts of single or separated metals on hypertension, and the critical metals contributing to the prevalence of hypertension are still under discussion. We collected data from 5092 participants across three consecutive National Health and Nutrition Examination Survey (NHANES) circles (2011-2016). Weighted logistic regression, weighted quantile sum (WQS) regression, quantile-based g-computation (QGC), and Bayesian kernel machine regression (BKMR) analyses were conducted to evaluate the combined and individual effects of 15 urinary metals, as well as to identify the critical metals on the development of hypertension. In our study, the weighted prevalence of hypertension was 37.9%, and the average age was 47.42 years. Manganese, uranium and tin were found as the independent risk factors for hypertension, while barium, lead, and thallium were found to have protective effects against hypertension. Lead, barium, tungsten, uranium, and tin were determined as critical elements for the prediction of hypertension. No significant interaction relationship was detected between multiple metals. There might be potential positive combined effects of urinary metal mixture on hypertension. Tungsten, uranium, and tin were positively associated with hypertension while lead and barium were negatively associated with hypertension. The underlying mechanisms of urinary metal exposure on the risk of hypertension deserve further investigations.

A State-of-the-Science Review on Metal Biomarkers.

PURPOSE OF REVIEW: Biomarkers are commonly used in epidemiological studies to assess metals and metalloid exposure and estimate internal dose, as they integrate multiple sources and routes of exposure. Researchers are increasingly using multi-metal panels and innovative statistical methods to understand how exposure to real-world metal mixtures affects human health. Metals have both common and unique sources and routes of exposure, as well as biotransformation and elimination pathways. The development of multi-element analytical technology allows researchers to examine a broad spectrum of metals in their studies; however, their interpretation is complex as they can reflect different windows of exposure and several biomarkers have critical limitations. This review elaborates on more than 500 scientific publications to discuss major sources of exposure, biotransformation and elimination, and biomarkers of exposure and internal dose for 12 metals/metalloids, including 8 non-essential elements (arsenic, barium, cadmium, lead, mercury, nickel, tin, uranium) and 4 essential elements (manganese, molybdenum, selenium, and zinc) commonly used in multi-element analyses. RECENT FINDINGS: We conclude that not all metal biomarkers are adequate measures of exposure and that understanding the metabolic biotransformation and elimination of metals is key to metal biomarker interpretation. For example, whole blood is a good biomarker of exposure to arsenic, cadmium, lead, mercury, and tin, but it is not a good indicator for barium, nickel, and uranium. For some essential metals, the interpretation of whole blood biomarkers is unclear. Urine is the most commonly used biomarker of exposure across metals but it should not be used to assess lead exposure. Essential metals such as zinc and manganese are tightly regulated by homeostatic processes; thus, elevated levels in urine may reflect body loss and metabolic processes rather than excess exposure. Total urinary arsenic may reflect exposure to both organic and inorganic arsenic, thus, arsenic speciation and adjustment for arsebonetaine are needed in populations with dietary seafood consumption. Hair and nails primarily reflect exposure to organic mercury, except in populations exposed to high levels of inorganic mercury such as in occupational and environmental settings. When selecting biomarkers, it is also critical to consider the exposure window of interest. Most populations are chronically exposed to metals in the low-to-moderate range, yet many biomarkers reflect recent exposures. Toenails are emerging biomarkers in this regard. They are reliable biomarkers of long-term exposure for arsenic, mercury, manganese, and selenium. However, more research is needed to understand the role of nails as a biomarker of exposure to other metals. Similarly, teeth are increasingly used to assess lifelong exposures to several essential and non-essential metals such as lead, including during the prenatal window. As metals epidemiology moves towards embracing a multi-metal/mixtures approach and expanding metal panels to include less commonly studied metals, it is important for researchers to have a strong knowledge base about the metal biomarkers included in their research. This review aims to aid metals researchers in their analysis planning, facilitate sound analytical decision-making, as well as appropriate understanding and interpretation of results.

Analysis of Whole Blood and Urine Trace Elements in Children with Autism Spectrum Disorders and Autistic Behaviors.

The relationship between trace elements and neurological development is an emerging research focus. We performed a case-control study to explore (1) the differences of 13 trace elements chromium (Cr), manganese (Mn), cobalt (Co), zinc (Zn), arsenic (As), selenium (Se), molybdenum (Mo), cadmium (Cd), stannum (Sn), stibium (Sb), mercury (Hg), titanium (TI), and plumbum (Pb) concentration in whole blood and urine between autism spectrum disorder (ASD) children and their typical development peers, and (2) the association between the 13 trace elements and core behaviors of ASD. Thirty ASD subjects (cases) and 30 age-sex-matched healthy subjects from Baise City, Guangxi Zhuang Autonomous Region, China, were recruited. Element analysis was carried out by inductively coupled plasma-optical emission spectrometry. Autistic behaviors were assessed using Autism Behavior Checklist (ABC), Childhood Autism Rating Scale (CARS), and Children Neuropsychological and Behavior Scale (CNBS). The whole blood concentrations of Mo (p = 0.004), Cd (0.007), Sn (p = 0.003), and Pb (p = 0.037) were significantly higher in the ASD cases than in the controls. Moreover, Se (0.393), Hg (0.408), and Mn (- 0.373) concentrations were significantly correlated between whole blood and urine levels in ASD case subjects. There were significant correlations between whole blood Sb (0.406), Tl (0.365), Mo (- 0.4237), Mn (- 0.389), Zn (0.476), and Se (0.375) levels and core behaviors of ASD. Although the mechanism of trace element imbalance in ASD is unclear, these data demonstrate that core behaviors of ASD may be affected by certain trace elements. Further studies are recommended for exploring the mechanism of element imbalance and providing corresponding clinical treatment measures.

In vitro inhibition of biofilm and virulence factor production in azole-resistant strains of Candida albicans isolated from diabetic foot by Artemisia vulgaris stabilized tin (IV) oxide nanoparticles.

The advent of nanotechnology has been instrumental in the development of new drugs with novel targets. Recently, metallic nanoparticles have emerged as potential candidates to combat the threat of drug-resistant infections. Diabetic foot ulcers (DFUs) are one of the dreadful complications of diabetes mellitus due to the colonization of numerous drug-resistant pathogenic microbes leading to biofilm formation. Biofilms are difficult to treat due to limited penetration and non-specificity of drugs. Therefore, in the current investigation, SnO2 nanoparticles were biosynthesized using Artemisia vulgaris (AvTO-NPs) as a stabilizing agent and were characterized using ultraviolet-visible (UV-vis) spectroscopy, Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). Furthermore, the efficacy of AvTO-NPs against biofilms and virulence factors of drug-resistant Candida albicans strains isolated from DFUs was assessed. AvTO-NPs displayed minimum inhibitory concentrations (MICs) ranging from 1 mg/mL to 2 mg/mL against four strains of C. albicans. AvTO-NPs significantly inhibited biofilm formation by 54.8%-87%, germ tube formation by 72%-90%, cell surface hydrophobicity by 68.2%-82.8%, and exopolysaccharide (EPS) production by 69%-86.3% in the test strains at respective 1/2xMIC. Biosynthesized NPs were effective in disrupting established mature biofilms of test strains significantly. Elevated levels of reactive oxygen species (ROS) generation in the AvTO-NPs-treated C. albicans could be the possible cause of cell death leading to biofilm inhibition. The useful insights of the present study could be exploited in the current line of treatment to mitigate the threat of biofilm-related persistent DFUs and expedite wound healing.

Novel metallomic profiling and non-carcinogenic risk assessment of botanical ingredients for use in herbal, phytopharmaceutical and dietary products using HR-ICP-SFMS.

Knowledge of element concentrations in botanical extracts is relevant to assure consumer protection given the increased interest in plant-based ingredients. This study demonstrates successful multi-element investigations in order to address the lack of comprehensive profiling data for botanical extracts, while reporting for the first time the metallomic profile(s) of arnica, bush vetch, sweet cicely, yellow rattle, bogbean, rock-tea and tufted catchfly. Key element compositions were quantified using a validated HR-ICP-SFMS method (µg kg-1) and were found highly variable between the different plants: Lithium (18-3964); Beryllium (3-121); Molybdenum (75-4505); Cadmium (5-325); Tin (6-165); Barium (747-4646); Platinum (2-33); Mercury (5-30); Thallium (3-91); Lead (12-4248); Bismuth (2-30); Titanium (131-5827); Vanadium (15-1758); Chromium (100-4534); Cobalt (21-652); Nickel (230-6060) and Copper (1910-6340). Compendial permissible limits were not exceeded. Overall, no evidence of a health risk to consumers could be determined from consumption of the investigated plants at reasonable intake rates. Mathematical risk modelling (EDI, CDI, HQ, HI) estimated levels above safe oral thresholds only for Cd (16%) and Pb (8%) from higher intakes of the respective plant-derived material. Following high consumption of certain plants, 42% of the samples were categorised as potentially unsafe due to cumulative exposure to Cu, Cd, Hg and Pb. PCA suggested a potential influence of post-harvest processing on Cr, Ti and V levels in commercially-acquired plant material compared to wild-collected and farm-grown plants. Moreover, a strong correlation was observed between Pb-Bi, Be-V, Bi-Sn, and Tl-Mo occurrence. This study may support future research by providing both robust methodology and accompanying reference profile(s) suitable for the quality evaluation of essential elements and/or metal contaminants in botanical ingredients.

Effects of shipwrecks on spatiotemporal dynamics of metal/loids in sediments and seafood safety in the Bay of Bengal.

Metal/loid pollution from shipwrecking activities has drawn significant concern due to their persistent threat to the marine ecosystem and human health. We investigated the spatiotemporal distribution, pollution characteristics, risks, sources, and potential impact of metal/loids in the sediments and seafood in the Bay of Bengal at nearby open beaching shipwrecking yards in Bangladesh. We collected 78 sediments and 208 seafood samples from the exposed and control sites from 2018 to 2020 during the dry and wet seasons. The concentrations of 16 elements, including cadmium, arsenic, lead, chromium, manganese, copper, zinc, iron, tin, antimony, nickel, cobalt, molybdenum, vanadium, selenium, and thallium were measured using validated inductively coupled plasma-mass spectrometry (ICP-MS) methods. Based on the pollution indices (enrichment factor, geoaccumulation index, pollution index, and pollution load index), lead, arsenic, cadmium, selenium, copper, zinc, and tin from the dry season showed higher contaminations compared to the wet and their concentrations were increased from 2018 to 2020 with seasonal fluctuations. Sediment cadmium and arsenic posed relatively higher and moderate ecological risks. Health risk analysis indicated that lead, cadmium, and inorganic arsenic (estimated) in seafood species pose a possible health threat to the general population. Further, there were possible ecological and health risks for the metal/loids in combination based on the ecological risk index in sediment and the hazard index in seafood, respectively. Source apportionment suggested that anthropogenic activities through uncontrolled shipwrecking operations over the last four decades were the largest polluting dominator, contributing 55-77% of the metal/loid concentrations. Therefore, the data may inform mitigation strategies for emission control at the shipwrecking yards to protect marine ecosystems and their local population.

Toxic Metals and Metalloids in Infant Formulas Marketed in Brazil, and Child Health Risks According to the Target Hazard Quotients and Target Cancer Risk.

Children are highly vulnerable to chemical exposure. Thus, metal and metalloid in infant formulas are a concern, although studies in this regard are still relatively scarce. Thus, the presence of aluminum, arsenic, cadmium, tin, mercury, lead, and uranium was investigated in infant formulas marketed in Brazil by inductively coupled plasma mass spectrometry, and the Target Hazard Quotients (THQ) and Target Cancer Risk (TCR) were calculated in to assess the potential risk of toxicity for children who consume these products continuously. Aluminum ranging from 0.432 ± 0.049 to 1.241 ± 0.113 mg·kg-1, arsenic from 0.012 ± 0.009 to 0.034 ± 0.006 mg·kg-1, and tin from 0.007 ± 0.003 to 0.095 ± 0.024 mg·kg-1 were the major elements, while cadmium and uranium were present at the lowest concentrations. According to the THQ, arsenic contents in infant formulas showed a THQ > 1, indicating potential health risk concerns for newborns or children. Minimal carcinogenic risks were observed for the elements considered carcinogenic. Metabolic and nutritional interactions are also discussed. This study indicates the need to improve infant formula surveillance concerning contamination by potentially toxic and carcinogenic elements.

Harmless Treatment of High Arsenic Tin Tailings and Environmental Durability Assessment.

The treatment of arsenic (As) in tin tailings (TT) has been an urgent environmental problem, and stabilization/solidification (S/S) treatment is considered an effective technology to eliminate contamination of As. In this study, we developed a low-carbon and low-alkalinity material to S/S of As, and the results showed that the leaching concentration of As after treatment was lower than the Chinese soil environmental quality standard (0.1 mg/L). Based on a series of characterization tests, we found that OH- promoted the dissolution of As(III)-S, Fe-As(V), and amorphous As(III)-O species and formed Ca-As(III) and Ca-(V) species with Ca2+. Simultaneously, hydration produces calcium silicate hydrate (C-S-H) gel and ettringite by the form of adsorption and ion exchange to achieve S/S of As. We also assessed the durability of this material to acidity and temperature, and showed that the leaching concentration of As was below 0.1 mg/L at pH = 1-5 and temperature 20-60 °C. The method proposed in this study, S/S of As, has excellent effect and environmental durability, providing a new solution for harmless treatment of TT and its practical application.

Ribosomal DNA copy number associated with blood metal levels in school-age children: A follow-up study on a municipal waste incinerator in Zhejiang, China.

To evaluate the body burdens of heavy metals and explore the impact of environmental metal exposure on ribosomal DNA (rDNA) or mitochondrial DNA (mtDNA) copy number (CN) variation in school-age children living near a municipal waste incinerator (MWI), we conducted a follow-up study in 2019. A total of 146 sixth-grade children from a primary school located 1.2 km away from the MWI were recruited for our study. Metals, including vanadium (V), chromium (Cr), manganese (Mn), cobalt (Co), nickel (Ni), copper (Cu), zinc (Zn), arsenic (As), selenium (Se), cadmium (Cd), stannum (Sn), stibium (Sb), thallium (Tl), and lead (Pb), were determined by an inductively coupled plasma mass spectrometer method. Real-time qPCR was used to measure the rDNA and mtDNA CN. The blood metal levels followed this order: Zn > Cu > Se > Pb > Mn > Sb > As > Ni > Cd > Co > Cr > Sn > V > Tl. Blood Cr level was significantly correlated with 18 S, 2.5 S, and 45 S CN (ß = -0.25, -0.22, -0.26, p < 0.05); Ni was correlated with 5 S (ß = -0.36, p < 0.01); Cu was correlated with 28 S, 18 S, and 5.8 S (ß = -0.24, -0.24, -0.23, p < 0.05); while Zn was correlated with 18 S, 5.8 S, and 45 S (ß = -0.28, -0.32, -0.26, p < 0.05). In conclusion, school-age children living near the MWI had lower blood metal levels compared to children recruited in 2013, while rDNA CN loss was found to be correlated to several heavy metals in these children.

Effects of Preconditioning With Transcutaneous Electrical Nerve Stimulation Monitored by Infrared Thermography on the Survival of Pedicled Perforator Flaps in a Rat Model.

OBJECTIVE: Pedicled perforator partial or complete necrosis with a rate of 13.7%. This study was undertaken to test whether preconditioning with transcutaneous electrical nerve stimulation (TENS) monitored by infrared thermography protect against partial necrosis by converting the choke anastomoses to the true anastomoses via inducing heme oxygenase-1 (HO-1) in a rat pedicled perforator flap model. METHODS: Seventy-two Sprague-Dawley rats were randomly assigned to the control, the TENS, the TENS + SnPP (tin protoporphyrin; HO-1 activity inhibitor; 50 µmol/kg) and the TENS +0.9% saline groups. On the unilateral dorsum of the rats, a rectangular flap donor site of 11 × 3 cm was marked out, which contained three perforator angiosomes and two choke zones. On days 1, 3 and 4, 1 hour of TENS (biphasic pulses, 25 mA, 80 Hz, 200 µs) was applied to the flap donor sites, respectively. On day 5, after the flap donor sites were assessed by infrared thermography, the flaps were harvested based on the deep circumflex iliac artery perforator. RESULTS: Infrared thermography showed that the choke zones in the flap donor sites presented white in the TENS and the TENS +0.9% saline groups, whereas they presented red in the control and the TENS + SnPP groups. Postmortem arteriography showed that the number of arterioles across each choke zone significantly increased in the TENS and the TENS +0.9% saline groups compared with the control and the TENS + SnPP groups. Immunohistochemistry and western blot showed a significant increase in HO-1 in the choke zones after TENS preconditioning. The necrotic area percentage of the flaps was significantly decreased in the TENS (4.3% ± 2.6%) and the TENS +0.9% saline groups (4.5% ± 2.3%) compared with the control (24.8% ± 5.0%) ( P < 0.001); there was no significant difference between the TENS and the TENS + SnPP (24.4% ± 7.3%) groups. CONCLUSIONS: These data show that TENS preconditioning monitored by infrared thermography might be a promising strategy to prevent pedicled perforator flaps from partial necrosis.

Hydrochemical evaluation of groundwater quality and human health risk assessment of trace elements in the largest mining district of South Khorasan, Eastern Iran.

The groundwater resources of mining areas have been in a challenging condition in terms of metal pollution and human health. Therefore, this study investigated the concentration of cobalt (Co), molybdenum (Mo), selenium (Se), tin (Sn), and antimony (Sb) in groundwater samples (wells, qanats, and springs) in a heavily contaminated mining district, South Khorasan, Eastern Iran. Human health risk of the studied metals to target groups was assessed, and water quality of the studied groundwater was investigated in the study area. A total of 367 sampling sites (279 wells, 74 qanats, and 14 springs) in South Khorasan Province were selected to collect the groundwater samples from June to July 2020. Sampling was performed thrice for each sampling point, and hydrochemical parameters were evaluated using a portable multiparameter. Inductively coupled plasma mass spectrometry (ICP-MS) was used to detect the metal concentrations. Results showed an order of Se > Mo > Sn > Co > Sb, and hazard index (HI) demonstrated a warning condition for south of South Khorasan (drinking application), southwest of South Khorasan (Irrigation application), and east and center of South Khorasan (drinking-irrigation application). Hydrochemical parameters showed a classification of "Na + K type" and "Mixed Ca-Mg-Cl type" with an overall group of "Na-Cl-HCO3" for sampled waters. Ficklin-Caboi diagram depicted a classification of "near-neutral low metal," and Schoeller diagram classified studied groundwater as "good" for drinking and irrigation consumptions and "Na-Cl" type based on ion balance diagram. Based on the correlation analysis, positive relationships were recorded among EC, TDS, Cl-, Na+, sulfate, Ca2+, salt, total hardness, Mg2+, ammonia, and K+ measured in the water samples. In essence, arid regions of the world greatly rely upon groundwater resources for drinking and irrigation consumptions, and mining districts with a heavy load of active mines can be a serious threat to the groundwater quality and human health.

Urinary metals, arsenic, and polycyclic aromatic hydrocarbon exposure and risk of chronic bronchitis in the US adult population.

Metals, arsenic, and polycyclic aromatic hydrocarbons (PAHs) have all been linked to respiratory diseases. Chronic bronchitis, which is a form of chronic obstructive pulmonary disease (COPD), is a major public health concern and source of morbidity and mortality in the US. The purpose of this study was to analyze the correlation of 14 urinary metals (antimony, barium, cadmium, cesium, cobalt, lead, manganese, mercury, molybdenum, strontium, thallium, tin, tungsten, uranium), seven species of arsenic, and seven forms of polycyclic aromatic hydrocarbon (PAH) concentrations and chronic bronchitis in the US population. A cross-sectional analysis using three datasets from the National Health and Nutrition Examination Survey (NHANES) between 2011 and 2016 in adults, aged 20 years and older. Chronic bronchitis was determined using a self-questionnaire from the NHANES dataset. A specialized weighted complex survey design analysis package was used to analyze NHANES data. Multivariate logistic regression models were used to determine the correlation between urinary metals, arsenic, PAHs, and chronic bronchitis. Models were adjusted for lifestyle and demographic factors. A total of 4186 participants were analyzed; 49.8% were female and 40.5% were non-Hispanic White. All seven types of PAHs showed a positive association with chronic bronchitis (1-hydroxynaphthalene odds ratio (OR): 1.559, 95% confidence interval (CI): 1.271-1.912; 2-hydroxynaphthalene OR: 2.498, 95% CI: 1.524-4.095; 3-hydroxyfluorene OR: 2.752, 95% CI: 2.100-3.608; 2-hydroxyfluorene OR: 3.461, 95% CI: 2.438-4.914; 1-hydroxyphenanthrene OR: 2.442, 95% CI: 1.515-3.937; 1-hydroxypyrene OR: 2.828, 95% CI: 1.728-4.629; 2 & 3-hydroxyphenanthrene OR: 3.690, 95% CI: 2.309-5.896). Of the metals, only urinary cadmium showed a statistically significant positive association (OR: 2.435, 95% CI: 1.401-4.235) with chronic bronchitis. No other metals or arsenic were correlated with chronic bronchitis. Seven forms of urinary PAHs, cadmium, and several demographic factors were associated with chronic bronchitis.

Trace Element Changes in the Plasma of Autism Spectrum Disorder Children and the Positive Correlation Between Chromium and Vanadium.

Existing data demonstrate a significant correlation between autism spectrum disorder (ASD) and the status of biologically essential and toxic trace elements. However, there is still a lack of data on the steady state of trace elements in ASD. We performed a case-control study to explore the association between the risk of ASD and 23 trace elements in plasma. The results showed that children with ASD had considerably decreased lithium (Li), manganese (Mn), selenium (Se), barium (Ba), mercury (Hg), and tin (Sn) levels when compared to their age- and sex-matched controls. Meanwhile, children with ASD had considerably increased plasma chromium (Cr) and vanadium (V) concentrations. We also divided each group into subgroups based on age and gender and created element-related networks for each subgroup. We detected significant element correlations within or between subgroups, as well as changes in correlations that included all elements examined. Finally, more element correlations were observed among males, which may open a new avenue for understanding the complicated process behind the sex ratio of children with ASD. Overall, our data revealed a novel relationship between elements and ASD, which may extend current understanding about ASD.

SiOxNy back-contact barriers for CZTSe thin-film solar cells.

The formation of molybdenum diselenide (MoSe2) is widely observed at the back-contact interface for copper zinc tin selenide (CZTSe) thin-film solar cells. Depending on individual selenium (Se) supply and thermal conditions for forming CZTSe absorbers on molybdenum (Mo) substrates, the thickness of MoSe2 can vary from a few hundreds of nanometers up to ≈ 1 µm, which is comparable to the commonly adopted thickness of 1 ~ 1.5 µm for CZTSe absorbers. In this study, for controlling the thickness of interfacial MoSe2, thin diffusion barrier layers of silicon oxynitride (SiOxNy) are deposited onto Mo layers prior to the growth of CZTSe absorbers in the fabrication process. As a result, a reduction in the thicknesses of MoSe2 layers is achieved. In terms of energy conversion efficiency (η), CZTSe solar cells grown on Mo/SiOxNy back contacts suffer a deterioration as the SiOxNy layers get thicker. CZTSe solar cells grown on Mo/SiOxNy/Mo back contacts preserve their efficiencies at ≈ 11% with thin 10 nm SiOxNy layers.

Two-Dimensional Tin Selenide (SnSe) Nanosheets Capable of Mimicking Key Dehydrogenases in Cellular Metabolism.

While dehydrogenases play crucial roles in tricarboxylic acid (TCA) cycle of cell metabolism, which are extensively explored for biomedical and chemical engineering uses, it is a big challenge to overcome the shortcomings (low stability and high costs) of recombinant dehydrogenases. Herein, it is shown that two-dimensional (2D) SnSe is capable of mimicking native dehydrogenases to efficiently catalyze hydrogen transfer from 1-(R)-2-(R')-ethanol groups. In contrary to susceptible native dehydrogenases, lactic dehydrogenase (LDH) for instance, SnSe is extremely tolerant to reaction condition changes (pH, temperature, and organic solvents) and displays extraordinary reusable capability. Structure-activity analysis indicates that the single-atom structure, Sn vacancy, and hydrogen binding affinity of SnSe may be responsible for their catalytic activity. Overall, this is the first report of a 2D SnSe nanozyme to mimic key dehydrogenases in cell metabolism.

Cross-Dehydrogenative Coupling Reactions Between C(sp)-H and X-H (X = N, P, S, Si, Sn) Bonds: An Environmentally Benign Access to Heteroatom-Substituted Alkynes.

Form a green and sustainable chemistry point of view, cross-dehydrogenative coupling (or oxidative cross-coupling) reactions have been recognized as environmentally sustainable and atom economical synthetic routes for the construction of new carbon-carbon and carbon-heteroatom bonds, since no pre-functionalization of starting materials is required. In the past few years, the direct coupling of sp-hybridized C-H bonds with heteroatom-H bonds has received much attention because of the importance of heteroatom-substituted alkynes in organic and medicinal chemistry. This review examines the recent developments in cross-dehydrogenative coupling reactions between C(sp)-H and X-H (X = N, P, S, Si, Sn) bonds, with a particular focus on the mechanistic aspects of the reactions.