Feasibility of direct promontory stimulation by bone conduction: A preliminary study of frequency-response characteristics in cats.

BACKGROUND: As an alternative pathway to air conduction, bone conduction is a multipathway process that transmits sound energy to the inner ear through the skull in general. Based on this mechanism, bone conduction devices (BCDs) have been used widely in the rehabilitation of hearing loss. Although great efforts have been devoted to improving BCDs, drawbacks still exist in most categories of BCDs due to the complicated process of bone conduction. We hypothesized that if a bone conduction transducer was placed on the cochlea to stimulate it directly, the attenuation would be minimized, and the frequency dependency would be different from that of the vibratory response induced by traditional BCDs. This study aimed to explore the feasibility of direct promontory stimulation and to investigate its frequency-response characteristics. METHODS: Measurements were conducted in twelve cat ears. To stimulate the promontory directly, the floating mass transducer (FMT) of the Vibrant Soundbridge© (VSB) implant was glued to the promontory coupled with an oval window (OW) coupler. Auditory brainstem response (ABR) and laser Doppler vibrometry (LDV) measurements were used to evaluate the auditory response induced by the FMT. In both measurements, the FMT was driven by direct voltage stimuli. RESULTS: ABR waves could be induced under direct promontory stimulation by the FMT. In the frequency range of 1-12 kHz, the variation in the voltage threshold level were limited to 16 dB SPL with a maximum of 0.2 V at 1 kHz and a minimum of 0.04 V at 10 kHz. In the LDV measurements and the relative motion of the round window membrane (RWM) and the promontory were used to evaluate the cochlear response. The LDV results indicated a weak frequency dependency from 1 to 12 kHz. CONCLUSION: Different from traditional stimulation via transcranial bone conduction, direct promontory stimulation is a new method in which a small bone conduction transducer stimulates the cochlear shell directly. The current experimental data demonstrate that it is feasible to generate sensations through bone conduction by stimulating the cochlea directly. Furthermore, the cochlear response induced by this type of stimulus in cats was weakly frequency dependent at frequencies ranging from 1 to 12 kHz. This study may provide a basis for the design of new transducers that can perform well over a wide range of frequencies.

A comparative study of MED-EL FMT attachment to the long process of the incus in intact middle ears and its attachment to disarticulated stapes head.

The Vibrant Soundbridge© (VSB) active middle-ear implant provides an effective treatment for mild-to-severe sensorineural hearing loss in the case of normal middle ear anatomy and mixed hearing loss in middle ear malformation. The VSB floating mass transducer (FMT), with proper couplers, can be installed on various structures of the ossicular chain, e.g., the short and long process of the incus, the stapes head, and the stapes footplate. A long process (LP) coupler is most commonly used for FMT attachment to the long process of the incus with intact ossicular chain, while CliP and Bell couplers are two standardized and reliable methods for FMT attachment to the stapes head with missing incus and malleus. However, the difference and relationship of the vibration properties among these three FMT couplers remain unclear. In the present study, the stapes footplate velocity responses of the LP, CliP, and Bell couplers have been investigated in eight fresh temporal bones (TBs) to evaluate the vibration properties of these three couplers. Normal and reconstructed middle ear transfer functions (METFs) were determined from laser Doppler vibrometer (LDV) measurements. A mastoidectomy and a posterior tympanotomy were performed to expose the ossicular chain. The METFs of the normal middle ear and middle ear with LP-FMT-coupler were compared under acoustic stimulation, thus the mass effect of the FMT with LP coupler was evaluated. Additional comparisons were made between the stapes footplate vibrations of the LP-FMT-coupler (with the intact ossicular chain at the long process of the incus), CliP-FMT-coupler and Bell-FMT-coupler on the stapes head (after incus and malleus removed) under active electromechanical stimulation. After the installation of CliP-FMT-coupler and Bell-FMT-coupler to the middle ear, the average velocity amplitude of the stapes footplate, comparing to the LP-FMT-coupler, was about 15 dB higher between 1 and 6 kHz, and 10 dB lower at about 0.5 kHz. Quantitatively, there was no significant difference between the CliP-FMT-coupler and Bell-FMT-coupler. According to our study, installation of CliP-FMT-coupler or Bell-FMT-coupler on the stapes head provides considerable improvement of the middle ear mechanical and functional responses, comparing with the LP-FMT-coupler in the temporal bone experiments. Moreover, the installation of the Bell-FMT-coupler to the stapes head produces essentially the same footplate velocity responses in comparison to the CliP-FMT-coupler.