Predicting Rates of Angular Correction After Hemiepiphysiodesis in Patients With X-Linked Hypophosphatemic Rickets.

PURPOSE: Patients with X-linked hypophosphatemic rickets (XLH) often develop coronal plane knee deformities despite medical treatment. Hemiepiphysiodesis is an effective way to correct coronal plane knee deformities in skeletally immature patients, but a full understanding of the rate of angular correction after hemiepiphysiodesis in XLH patients, compared with idiopathic cases is lacking. METHODS: We retrospectively reviewed charts of 24 XLH patients and 37 control patients without metabolic bone disease who underwent hemiepiphysiodesis. All patients were treated with standard-of-care medical therapy (SOC=active vitamin D and phosphate salt supplementation) in our clinical research center and had a minimum of 2-year follow-up after hemiepiphysiodesis. Demographic data as well as complications, repeat procedures, or recurrence/overcorrection were recorded. Standing lower extremity radiographs were evaluated before the surgical intervention and at subsequent hardware removal or skeletal maturity, whichever came first. Mean axis deviation, knee zone, mechanical lateral distal femoral angle (mLDFA), and medial proximal tibial angle were measured on each radiograph. The rate of angular correction was calculated as the change in mLDFA and medial proximal tibial angle over the duration of treatment. RESULTS: The magnitude of the initial deformity of the distal femur was greater in XLH patients as compared with control for varus (XLH mLDFA 97.7 +/- 4.9 vs. Control mLDFA 92.0 +/- 2.0 degrees) and valgus (XLH mLDFA 78.7 +/- 6.2 vs. Controls mLDFA 83.6 +/- 3.2 degrees). The rate of correction was dependent on age. When correcting for age, XLH patients corrected femoral deformity at a 15% to 36% slower rate than control patients for the mLDFA (>3 y growth remaining XLH 0.71 +/- 0.46 vs. control 0.84 +/- 0.27 degrees/month, <3 y growth remaining XLH 0.37 +/- 0.33 vs. control 0.58 +/- 0.41 degrees/month). No significant differences were seen in the rate of proximal tibia correction. XLH patients were less likely to end treatment in zone 1 (55.0% XLH vs. 77.8% control). XLH patients had longer treatment times than controls (19.5 +/- 10.7 vs. 12.6 +/- 7.0 mu, P value <0.001), a higher average number of secondary procedures than controls (1.33 +/- 1.44 vs. 0.62 +/- 0.92 number of procedures), a higher rate of overcorrection than controls (29.2% vs. 5.4%), and a higher rate of subsequent corrective osteotomy than controls (37.5% vs. 8.1%). There was no significant difference in the rate of complications between groups (8.3% vs. 5.4%). CONCLUSIONS: Patients with XLH undergoing hemiepiphysiodesis have a 15% to 36% slower rate of femoral deformity correction that results in longer treatment times, a higher likelihood to undergo more secondary procedures, and a lower likelihood to reach neutral mechanical alignment. SIGNIFICANCE: This study provides important information to guide the timing and treatment of patients with XLH and coronal plane knee deformities. In addition, results from this study can be educational for families and patients with respect to anticipated treatment times, success rates of the procedure, complication rate, and likelihood of needing repeat procedures.

Lower resource utilization for patients with healed diabetic foot ulcers during participation in a prevention program with foot temperature monitoring.

INTRODUCTION: We assessed the impact of a diabetic foot ulcer prevention program incorporating once-daily foot temperature monitoring on hospitalizations, emergency department and outpatient visits, and rates of diabetic foot ulcer recurrence and lower extremity amputations for patients with recently healed foot ulcers. RESEARCH DESIGN AND METHODS: In this retrospective analysis of real-world data, we enrolled 80 participants with a healed diabetic foot ulcer in a year-long foot ulcer recurrence prevention program. Four outpatient centers within a large integrated healthcare system in the USA contributed to enrollment. We evaluated diabetic foot-related outcomes and associated resource utilization for participants during three periods: the 2 years before the program, the year during the program, and after the program ended. We reported unadjusted resource utilization rates during the program and the periods before and after it. We then adjusted rates of outcomes in each phase using an interrupted time series approach, explicitly controlling for overall trends in resource utilization and recurrence during the three periods. RESULTS: Our unadjusted data showed high initial rates of resource utilization and recurrence before enrollment in the program, followed by lower rates during the program, and higher rates of resource utilization and similar rates of recurrence in the period following the end of the program. The adjusted data showed lower rates of hospitalizations (relative risk reduction (RRR)=0.52; number needed to treat (NNT)=3.4), lower extremity amputations (RRR=0.71; NNT=6.4), and outpatient visits (RRR=0.26; absolute risk reduction (ARR)=3.5) during the program. We also found lower rates of foot ulcer recurrence during the program in the adjusted data, particularly for wounds with infection or greater than superficial depth (RRR=0.91; NNT=4.4). CONCLUSIONS: We observed lower rates of healthcare resource utilization for high-risk participants during enrollment in a diabetic foot prevention program incorporating once-daily foot temperature monitoring. TRIAL REGISTRATION NUMBER: NCT04345016.

In vitro analysis of a hepatic device with intrinsic microvascular-based channels.

A novel microfluidics-based bilayer device with a discrete parenchymal chamber modeled upon hepatic organ architecture is described. The microfluidics network was designed using computational models to provide appropriate flow behavior based on physiological data from human microvasculature. Patterned silicon wafer molds were used to generate films with the vascular-based microfluidics network design and parenchymal chamber by soft lithography. The assembled device harbors hepatocytes behind a nanoporous membrane that permits transport of metabolites and small proteins while protecting them from the effects of shear stress. The device can sustain both human hepatoma cells and primary rat hepatocytes by continuous in vitro perfusion of medium, allowing proliferation and maintaining hepatic functions such as serum protein synthesis and metabolism. The design and fabrication processes are scalable, enabling the device concept to serve as both a platform technology for drug discovery and toxicity, and for the continuing development of an improved liver-assist device.