Determination of phosphorus in water and chemical fertilizer samples using a simple drawing microfluidic paper-based analytical device.

A simple one-step drawing for the cost-effective fabrication of microfluidic paper-based analytical devices (µPADs) for the determination of phosphate content in water and fertilizer samples is presented in this paper. The hydrophobic barrier of µPAD was patterned using a 2-mm tip marker pen using a transparent acrylic sheet template. The molybdenum blue reaction using ascorbic acid as a reducing agent was used. A pre-concentration step of samples is proposed to improve the sensitivity of the measurement. The blue complex produced on the µPADs was recorded using a smartphone camera. The color intensities (red, green, blue and gray) were analyzed using ImageJ program. The proposed µPAD method provides a linear calibration range from 0 to 100 mg L-1 P. The limit of detection (LOD) was found to be 0.7 mg L-1 P with a precision of 3.1%RSD for 50 mg L-1 P (n = 10). The proposed method was successfully applied to the determination of phosphorus contents in water and liquid chemical fertilizer samples. The results obtained from µPAD agreed with a spectrophotometric method using paired t test at a 95% confidence level.

A simple cost-effective paper-based electrochemical device for detection of adulterated sibutramine in slimming products.

This work presents the first paper-based electrochemical device, or ePAD, for direct detection of adulterated sibutramine in slimming products. The ePAD was fabricated using a screen-printing technique for defining the hydrophilic area for sample loading and for the working, reference and counter electrodes. The ePAD gave reproducible responses comparable to both conventional rod electrodes and commercial screen-printed electrodes (SPEs). Use of paper to fabricate the ePAD device provides advantages over the conventional SPE platforms (e.g. glass, ceramics and polymers) in terms of biocompatibility, strong capillary action and environmental friendliness. To detect sibutramine, square wave voltammetry was employed after sample loading on the circular hydrophilic area. The linear range is 2.51 to 83.7 mg L-1 sibutramine, with a precision of 6 %RSD (n = 3) and an instrumental limit of detection (3SD of intercept/slope) of 2.46 mg L-1 sibutramine. Recovery of spiked samples ranged from 83 to 116%. The samples were capsules, slimming coffee powders and nutraceutical beverages. The samples were appropriately diluted to give concentrations within the linear calibration range. Filtration of undissolved solids found with the capsules and coffee powder samples was not required, demonstrating that the method is not susceptible to solid particles. The ePAD is cost-effective (

Contactless conductivity sensor employing moist paper as absorbent for in-situ detection of generated carbon dioxide gas.

This work presents an unconventional use of capacitively coupled contactless conductivity detector (C4D) for detection of gas absorption by moist paper with potential application for chemical analysis. To be suitable for measuring conductivity of moist paper absorbent, the C4D sensor was therefore designed in planar configuration. A layer of dry filter paper, only 20 mm × 25 mm in size, was placed on the C4D sensor and the device installed inside a specifically designed vaporization chamber. A vial (16 mm i.d., 8 mm high) containing a 150-µL solution of sodium bicarbonate was placed alongside. The filter paper was loaded with 110 µL of deionized water through an injection hole in the cover lid. A 100-µL aliquot of 2 M hydrochloric acid solution was directly dispensed into the vial through a second hole in the lid to generate CO2 gas from the bicarbonate solution. It was observed that the C4D sensor gave real-time response that corresponded to the absorption of the gas and subsequent production of H+ and HCO3- in the moist paper. The monitored signal reached a constant value at 160 s after the addition of the acid. Chemistry of the absorption process and equivalent circuit for the C4D are proposed. Direct measurement of cement powder was chosen to demonstrate the potential use of this device for quantifying the CaCO3 content of the cement. The calibration curve for 0.5-3 mg CaCO3 was linear for signals recorded at 160 s: Vdc = (0.172 ± 0.005) · (mg CaCO3) + (0.016 ± 0.009), with coefficient of determination of 0.9965. Linear calibrations were also observed when the signals were monitored at various time less than 160 s. The limit of quantitation (3 SD of intercept/slope) was 0.17 mg CaCO3. The method provided acceptable precision with %RSD of 4.6 (2 mg CaCO3, n = 10).

AAO-CNTs electrode on microfluidic flow injection system for rapid iodide sensing.

In this work, carbon nanotubes (CNTs) nanoarrays in anodized aluminum oxide (AAO-CNTs) nanopore is integrated on a microfluidic flow injection system for in-channel electrochemical detection of iodide. The device was fabricated from PDMS (polydimethylsiloxane) microchannel bonded on glass substrates that contains three-electrode electrochemical system, including AAO-CNTs as a working electrode, silver as a reference electrode and platinum as an auxiliary electrode. Aluminum, stainless steel catalyst, silver and platinum layers were sputtered on the glass substrate through shadow masks. Aluminum layer was then anodized by two-step anodization process to form nanopore template. CNTs were then grown in AAO template by thermal chemical vapor deposition. The amperometric detection of iodide was performed in 500-µm-wide and 100-µm-deep microchannels on the microfluidic chip. The influences of flow rate, injection volume and detection potential on the current response were optimized. From experimental results, AAO-CNTs electrode on chip offers higher sensitivity and wider dynamic range than CNTs electrode with no AAO template.

A microfluidic system for evaluation of antioxidant capacity based on a peroxyoxalate chemiluminescence assay.

A microfluidic system incorporating chemiluminescence detection is reported as a new tool for measuring antioxidant capacity. The detection is based on a peroxyoxalate chemiluminescence (PO-CL) assay with 9,10-bis-(phenylethynyl)anthracene (BPEA) as the fluorescent probe and hydrogen peroxide as the oxidant. Antioxidant plugs injected into the hydrogen peroxide stream result in inhibition of the CL emission which can be quantified and correlated with antioxidant capacity. The PO-CL assay is performed in 800-microm-wide and 800-microm-deep microchannels on a poly(dimethylsiloxane) (PDMS) microchip. Controlled injection of the antioxidant plugs is performed through an injection valve. Of the plant-food based antioxidants tested, beta-carotene was found to be the most efficient hydrogen peroxide scavenger (SAHP of 3.27x10(-3) micromol-1 L), followed by alpha-tocopherol (SAHP of 2.36x10(-3) micromol-1 L) and quercetin (SAHP of 0.31x10(-3) micromol-1 L). Although the method is inherently simple and rapid, excellent analytical performance is afforded in terms of sensitivity, dynamic range, and precision, with RSD values typically below 1.5%. We expect our microfluidic devices to be used for in-the-field antioxidant capacity screening of plant-sourced food and pharmaceutical supplements.