Simultaneous high-temperature gas chromatography with flame ionization and mass spectrometric analysis of monocarboxylic acids and acylglycerols in biofuels and biofuel intermediate products.

Triacyl-, diacyl- and monoacylglycerols (TAGs, DAGs, MAGs) along with monocarboxylic acids (MCAs) are intermediate products in many triacylglycerol oil-to-biofuel conversion pathways. Accumulation of these compounds leads to poor biofuel characteristics and may result in fuel system damage. We developed a method for simultaneous identification and quantification of a wide range of MCAs (C4-C18), MAGs, DAGs, and TAGs. The method is based on trimethylsilylation followed by high temperature GC with programmed temperature vaporizer (PTV) injection coupled to parallel FID and MS detectors (HTGC-FID/MS). To minimize the discrimination of both low and high molecular weight species typically occurring on the injector, we optimized injection conditions using a central composite design. The critical variables were the time at initial temperature (40 °C), splitless time, and the interaction between these two parameters. Among three tested electron ionization source/quadrupole analyzer temperatures, a 350/200 °C setting provided the highest response and signal-to-noise ratio for TAGs and did not have an effect on MAGs and DAGs. Similar results were obtained when quantifying target analytes in intermediate products of soybean oil cracking with FID and MS (using specific acylglycerol fragmentation ions). The instrumental FID limits of detection (LODs) were 0.07-0.27 ng for most of the target analytes. Selected ion monitoring (SIM) LODs were 0.01-0.05 ng for MCAs and 0.03-0.14 ng for acylglycerols. For the total ion current (TIC), LODs observed increased with acyl chain length and degree of unsaturation, resulting in an increase from 0.05 to 0.18 ng for MCAs (C5 to C18) and from 0.03 to 1.8 ng for acylglycerols (TAGs C8 to C22). Deviations in the repeatability of sample preparation, intra- and inter-day analyses, including sample stability over an eight-day time period, did not exceed 10% variance. These results demonstrate that the developed method is accurate and robust for the determination of acylglycerols and MCAs produced during the processing of TAGs into biofuels.

Method development for the characterization of biofuel intermediate products using gas chromatography with simultaneous mass spectrometric and flame ionization detections.

Accurate analytical methods are required to develop and evaluate the quality of new renewable transportation fuels and intermediate organic liquid products (OLPs). Unfortunately, existing methods developed for the detailed characterization of petroleum products, are not accurate for many of the OLPs generated from non-petroleum feedstocks. In this study, a method was developed and applied to the detailed characterization of complex OLPs formed during triacylglyceride (TG) pyrolysis which is the basis for generating one class of emerging biofuels. This method uses gas chromatography coupled simultaneously with flame ionization and mass spectrometry detectors (GC-FID/MS). The FID provided accurate quantification of carbonaceous species while MS enabled identification of unknown compounds. A programed temperature vaporizer using a 25 °C, 0.1 min, 720 °C min(-1), 350 °C, 5 min temperature program is employed which minimizes compound discrimination better than the more commonly utilized split/splitless injector, as verified with injections at 250 and 350 °C. Two standard mixtures featuring over 150 components are used for accurate identification and a designed calibration standard accounts for compound discrimination at the injector and differing FID responses of various classes of compounds. This new method was used to identify and quantify over 250 species in OLPs generated from canola oil, soybean oil, and canola methyl ester (CME). In addition to hydrocarbons, the method was used to quantify polar (upon derivatization) and unidentified species, plus the unresolved complex mixture that has not typically been determined in previous studies. Repeatability of the analytical method was below 5% RSD for all individual components. Using this method, the mass balance was closed for samples derived from canola and soybean oil but only ca. 77 wt% of the OLP generated from CME could be characterized. The ability to close the mass balance depended on sample origin, demonstrating the need for an accurate quantification method for biofuels at various stages of production.

A study of fine particulate emissions from combustion of treated pulverized municipal sewage sludge.

Municipal sewage sludge (MSS) is formed during wastewater treatment and its processing and disposal represent one of the most environmentally challenging aspects of the wastewater treating process. One disposal option currently being considered is a process involving heat treatment (to render the sludge biologically inactive) followed by dewatering, drying, pulverizing, and combustion. This research focuses on fine particle emissions from the combustion of dried, treated, MSS, cofired with either natural gas or pulverized Ohio bituminous coal as a supplemental fuel. These fuels were burned at 13 kW in a downflow laboratory combustor designed to replicate time/temperature histories and particle concentrations typical of practical combustion units yet also sufficiently well defined aerodynamically to allow elucidation of mechanisms. Size-segregated particle size distributions were obtained by isokinetic sampling followed by dilution/quenching and passage into a Berner Low-Pressure Impactor. Major and trace elements were analyzed by flame and graphite furnace atomic absorption spectroscopy. Four particle size regions were identified: furnace vapor-phase material that formed ultrafine particles either in or just before the sampling probe, submicron-sized particles formed during the combustion process, micron-sized fine particles, and larger supermicron sized bulk fly ash particles. The fuel mix appears to influence trace metal partitioning routes and the composition of fine particulate matter in the exhaust. Cofiring of MSS with coal increases the ultrafine/submicron particle emission compared to firing coal alone. This increase in ultrafine/submicron particles is most likely due to an interaction between species derived from MSS (possibly alkali metals) and those from coal (possibly sulfur and/or chlorine). Vapor-to-solid phase partitioning of arsenic and selenium is controlled by surface reaction with active surface sites during MSS combustion with either gas or coal. Co-combustion of MSS with the Ohio bituminous coal allows the arsenic and selenium to be reactively scavenged by calcium, thus changing the speciation of the trace metal emitted. Ohio bituminous coal alone contained insufficient calcium to accomplish this same scavenging effect.