Fluorescence-estimated oil concentration (Foil) in the Deepwater Horizon subsea oil plume.

Tracking the subsea oil plume during the 2010 Deepwater Horizon Oil Spill (DWH) was conducted using in situ fluorescence via vertical profilers (n = 1157) and discrete sample chemical analyses (n = 7665). During monitoring efforts, discrete samples provided a coarse picture of the oil plume footprint, but the majority of the samples were below standard analytical detection limits for petroleum hydrocarbons. In situ fluorescence data improved the spatial and temporal resolution of the subsea oil plume characterization. Here we synthesized millions of continuous fluorescence data points from hundreds of contemporaneously discrete samples collected to demonstrate how fluorescence could serve as a proxy for Benzene-Toluene-Ethylbenzene-Xylene (BTEX) concentration. Data mined from Gulf Science Data repository were well correlated, and geographically and temporally aligned to provide direct comparisons. Described here are the methods used to calibrate the fluorescence data and to spatially approximate the three-dimensional geographic extent of the oil plume.

Comparative Toxicity of Oil Spill Herding Agents to Aquatic Species.

Chemical herding agents are surfactant mixtures used to coalesce spilled oil and increase slick thickness to facilitate mechanical recovery or in situ burning. Only two herders are currently listed on the United States' National Oil and Hazardous Substances Pollution Contingency Plan or National Contingency Plan product schedule for potential use in spill response: the surface collecting agents Siltech OP-40™ and ThickSlick 6535™. Toxicity data for spill response agents are frequently available only for two estuarine species, mysid shrimp (Americamysis bahia) and inland silversides (Menidia beryllina), and are particularly limited for herding agents. Toxicity can vary over several orders of magnitude across product type and species, even within specific categories of spill response agents. Seven aquatic species were tested with both Siltech OP-40™ and ThickSlick 6535™ to evaluate acute herder toxicity and relative species sensitivity. The toxicity assessment included: acute tests with A. bahia and M. beryllina, the freshwater crustacean Ceriodaphina dubia, and the freshwater fish Pimephales promelas; development of the echinoderm Arbacia unctulate; and growth of a freshwater alga Raphidocelis subcapitata and marine alga Dunaliella tertiolecta. Siltech acute toxicity values ranged from 1.1 to 32.8 ppm. ThickSlick acute toxicity values ranged from 2.2 to 126.4 ppm. The results of present study show greater toxicity of Siltech compared to ThickSlick with estimated acute hazard concentrations intended to provide 95% species protection of 1.1 and 3.6 ppm, respectively, on empirical data and 0.64 and 3.3 ppm, respectively, with the addition of interspecies correlation data. The present study provides a greater understanding of species sensitivity of these two oil spill response agents. Environ Toxicol Chem 2022;41:1311-1318. © 2022 SETAC. This article has been contributed to by U.S. Government employees and their work is in the public domain in the USA.

Analysis of emissions and residue from methods to improve efficiency of at-sea, in situ oil spill burns.

The combustion efficiency of simulated at-sea surface oil burns (in situ burns) was determined in a 63 m3 tank while testing varied boom configurations and air-assist nozzles in the presence and absence of waves. Combustion efficiencies of Alaska North Slope oil based on unburned carbon in the plume emissions ranged from 85% to 93% while values based on oil mass loss ranged from 89% to 99%. A four-fold variation in PM2.5 emission factors was observed from the test conditions. The most effective burns in terms of reduced emissions and post-burn residue concentration of total petroleum hydrocarbons were those that had high length to width boom ratios resulting in higher flame front surface area exposure to ambient air. The amount of oil mass lost was not related to any combustion efficiency parameters measured in the plume, representing a potential tradeoff between unburnt oil and air pollution.

Toxicity of oil spill response agents and crude oils to five aquatic test species.

The majority of aquatic toxicity data for petroleum products has been limited to a few intensively studied crude oils and Corexit chemical dispersants, and acute toxicity testing in two standard estuarine test species: mysids (Americamysis bahia) and inland silversides (Menidia beryllina). This study compared the toxicity of two chemical dispersants commonly stock piled for spill response (Corexit EC9500A®, Finasol®OSR 52), three less studied agents (Accell Clean®DWD dispersant; CytoSol® surface washing agent; Gelco200® solidifier), and three crude oils differing in hydrocarbon composition (Dorado, Endicott, Alaska North Slope). Consistent with listings on the U.S. National Contingency Plan Product Schedule, general rank order toxicity was greatest for dispersants and lowest for the solidifier. The results indicate that freshwater species can have similar sensitivity as the conventionally tested mysids and silversides, and that the sea urchin (Arbacia punctulata) appears to be a reasonable addition to increase taxa diversity in standardized oil agent testing.

Characterization of solidifiers used for oil spill remediation.

The physical characteristics and chemical composition of oil spill solidifiers were studied, and correlation of these properties with product effectiveness enabled determination of characteristics that are desirable in a good solidifier. The analyses revealed that the commercial products were primarily comprised of organic polymers and a few trace elements. A natural sorbent, which was composed entirely of plant based matter, was also evaluated, and it had the highest oil removal capacity, but it did not produce a solid mat-like final product. Generally, solidifiers with a carbonate group, pore size greater than 5 µm, and bulk densities lower than 0.3 g cm(-3) were found to have better efficiency and produced a cohesive rubbery final product that facilitated removal compared to sorbents. The importance of bulk density and pore size in the performance of the solidifier suggest that the primary mechanism of action was likely physical sorption.

Parametric study to determine the effect of temperature on oil solidifier performance and the development of a new empirical correlation for predicting effectiveness.

Temperature can play a significant role in the efficacy of solidifiers in removing oil slicks on water. We studied and quantified the effect of temperature on the performance of several solidifiers using 5 different types of oils under a newly developed testing protocol by conducting experiments in constant temperature rooms set at 22°C and 5°C. The results indicated that solidifier efficiency decreased substantially at the lower temperature, especially at lower application rates. The removal efficiency of the solidifier was in general directly proportional to temperature, except for the heavier oils, where removal by attachment was observed. Solidifier products with lower powder bulk density exhibited the best removal effectiveness. Analysis of experimental data yielded empirical correlations involving certain operational variables such as application rate, temperature, solidifier property (bulk density), and oil property (viscosity). Regression analysis was used to fit a mathematical model to the experimental solidifier effectiveness data.