Using affinity capillary electrophoresis and computational models for binding studies of heparinoids with p-selectin and other proteins.

A fast and precise affinity capillary electrophoresis (ACE) method has been developed and applied for the investigation of the binding interactions between P-selectin and heparinoids as potential P-selectin inhibitors in the presence and absence of calcium ions. Furthermore, model proteins and vitronectin were used to appraise the binding behavior of P-selectin. The normalized mobility ratios (∆R/Rf ), which provided information about the binding strength and the overall charge of the protein-ligand complex, were used to evaluate the binding affinities. It was found that P-selectin interacts more strongly with heparinoids in the presence of calcium ions. P-selectin was affected by heparinoids at the concentration of 3 mg/L. In addition, the results of the ACE experiments showed that among other investigated proteins, albumins and vitronectin exhibited strong interactions with heparinoids. Especially with P-selectin and vitronectin, the interaction may additionally induce conformational changes. Subsequently, computational models were applied to interpret the ACE experiments. Docking experiments explained that the binding of heparinoids on P-selectin is promoted by calcium ions. These docking models proved to be particularly well suited to investigate the interaction of charged compounds, and are therefore complementary to ACE experiments.

Use of short chain alkyl imidazolium ionic liquids for on-line stacking and sweeping of methotrexate, flinic acid and folic acid: their application to biological fluids.

Methotrexate (MTX) is widely used for the treatment of many types of cancer. Folinic acid (FNA) and folic acid (FA) were usually simultaneously supplemented with MTX to reduce the side effects of a folate deficiency. This study, for the first time, included on-line sample preconcentration by stacking and sweeping techniques under reduced or enhanced electric conductivity in the sample region using short chain alkyl imidazolium ionic liquids (ILs) as micelle forming agents for analyte focusing. Both analyte focusing by micelle collapse (AFMC) and sweeping-MEKC had been investigated for the comparison of their effectiveness to examine simultaneously MTX, FNA and FA in plasma and urine under physiological conditions. In sweeping-MEKC, the sample solution without micelles was hydrodynamically injected as a long plug into a fused-silica capillary pre-filled with phosphate buffer containing 3.0 mol/L of 1-butyl-3-methylimidazolium bromide (BMIMBr). Using AFMC, the analytes were prepared in BMIMBr micellar matrix and hydrodynamically injected into the phosphate buffer without IL micelles. The conductivity ratio between BGE and sample (γ, BGE/sample) was optimized to be 3.0 in sweeping-MEKC and 0.33 in AFMC resulting the adequate separation of analytes within 4.0 min. To reduce the possibility of BMIMBr adsorption, an appropriate rinsing protocol was used. The limits of detection were calculated as 0.1 ng/mL MTX, 0.05 ng/mL FNA and 0.05 ng/mL FA by sweeping-MEKC and 0.5 ng/mL MTX, 0.3 ng/mL FNA and 0.3 ng/mL FA by AFMC. The accuracy was tested by recovery in plasma and urine matrices giving values ranging between 90 and 110%. Both stacking and sweeping by BMIMBr could be successfully used for the rapid, selective and sensitive determination of pharmaceuticals in complex matrices due to its fascinating properties, including high conductivity, good thermal stability and ability to form different types of interactions by electrostatic, hydrophobic, hydrogen bonding and π-π interactions. In sweeping-MEKC, the using of BMIMBr enhanced the γ factor, k retention factor and the injected amount of sample. Consequently, this technique offers particular potential for higher sensitivity by giving 22- and 5-fold sensitivity enhancement factors (SEFs) of MTX compared to CZE and AFMC, respectively.

Analytical instrument qualification in capillary electrophoresis.

Capillary electrophoresis (CE) is a well-established and frequently used technique in the pharmaceutical industry. Therefore an appropriate analytical instrument qualification (AIQ) is required for quality assurance. AIQ forms the basis of a quality management followed by analytical method validation, system suitability tests (SSTs) and quality control checks. Two parts of the AIQ, namely the operational qualification (OQ) and the performance qualification (PQ) are of particular interest in the daily routine of the laboratory. A new concept for OQ and PQ was developed to assure the correct function of a CE system. The significance of each parameter, possible test methods as well as acceptance criteria will be presented and discussed in detail. Especially temperature adjustment by the cooling system and the voltage supply must be tested for accurate and precise operation. The detector noise, wavelength accuracy and detector linearity have to be checked as well. Finally, the injection linearity, accuracy and precision need to be qualified. The proposed set of qualification procedures is easy to implement and was already tested on five CE instruments from three different manufacturers. A time- and cost-saving continuous PQ was derived, using results from method-specific SSTs and some additional experiments. This holistic concept continuously surveys the most relevant parameters, hence assuring the suitability of the used instruments and decreasing their downtimes.

Efficient and economic HPLC performance qualification.

Analytical instrument qualification (AIQ) is a prerequisite for any analytical method validation and thus must be considered as a vital basis of analytical data integrity and quality in pharmaceutical analysis. There is a well-established system of qualification phases-Design Qualification, Installation Qualification (IQ), Operational Qualification (OQ) and Performance Qualification (PQ). As HPLC systems are "off the shelf" equipment, Design Qualification may be disregarded here. IQ establishes that the instrument is received as designed and that it is properly installed. OQ is carried out modularly with the intention to ensure that the specific modules of the system and the whole system are operating according to the defined specifications. PQ as the last step of the initial qualification is supposed to ensure continued satisfactory performance of an instrument under actual running conditions over the anticipated working range during daily use. However, PQ is not a one time exercise, but is currently repeated regularly independently from routine use of the analytical system using standard reference test condition. But this approach, which is time consuming and expensive only provides a snapshot of system performance. As HPLC procedures generally require a system suitability test (SST) prior and/or after test, it might be far more reasonable and robust to use these SST data for a continuous PQ. The work presented here demonstrates that, under certain circumstances, satisfactory instrument performance assessment can be derived from system suitability tests and performance data from daily use as well. A generally accepted qualification list, consisting of only twelve critical parameters, was compiled in a first step. Some parameters such as injector or thermostatting accuracy were considered redundant while others were successfully incorporated in the proposed holistic approach. System suitability test data as well as OQ/PQ data were provided from different sources and evaluated. The promising results confirmed our concept of ongoing/continuous PQ as a major improvement in AIQ. This approach will not only help to reduce time and effort in the daily laboratory routine without losing data quality, but also avoid the critical re-evaluation of numerous analytical tests once a routine PQ fails.