Design of chitosan/boehmite biocomposite for the removal of anionic and nonionic dyes from aqueous solutions: Adsorption isotherms, kinetics, and thermodynamics studies.

This study introduces a chitosan/boehmite biocomposite as an efficient adsorbent for removing anionic Congo Red (CR) and non-ionic Bromothymol Blue (BTB) from water. Boehmite nanoparticles were synthesized using the Sol-gel method and then attached to chitosan particles using sodium tripolyphosphate through co-precipitation method. Characterized through FTIR, FE-SEM, BET, and XRD, the biosorbent displayed structural integrity with optimized pH conditions of 3 for CR and 4 for BTB, achieving over 90 % adsorption within 30 min. Pseudo second order kinetics model and Langmuir isotherm revealed monolayer sorption with capacities of 64.93 mg/g for CR and 90.90 mg/g for BTB. Thermodynamics indicated a spontaneous and exothermic process, with physisorption as the primary mechanism. The biosorbent demonstrated excellent performance and recyclability over five cycles, highlighting its potential for eco-friendly dye removal in contaminated waters.

Pyto-Architechture of Ag, Au and Ag-Au bi-metallic nanoparticles using waste orange peel extract for enable carcinogenic Congo red dye degradation.

Ecologically inspired to develop silver, gold and silver/gold bimetallic nanoparticles from discarded orange peel extract. The plant-derived compounds included in discarded orange peel extract have been accountable for the development of Ag, Au and Ag-Au bimetallic nanoparticles, that might be used in the biosynthetic process. The qualitative assessment of developed silver, gold and silver/gold bimetallic nanoparticles has been performed by UV-visible, XRD pattern, FT IR analysis, TEM/HRTEM, EDX and BET isotherm analysis. In this investigation, the photocatalytic effect of developed silver, gold and silver/gold bimetallic nanoparticles on Congo red dye breakdown efficiency was achieved at 96%, 94%, and 99.2%, respectively. Due to prolonged electron-hole recombination process was investigated using UV irradiation and reused for up to 5 consecutive runs without significant loss of photocatalytic activity. Moreover, silver, gold, and silver/gold bimetallic nanoparticles manufactured in an environmentally benign manner could potentially contribute to the ecological cleanup.

Nitrogen sources alter ligninase and cellulase activities of thermophilic fungi isolated from compost and vermicompost.

Fungi harboring lignocellulolytic activity accelerate the composting process of agricultural wastes; however, using thermophilic fungal isolates for this process has been paid little attention. Moreover, exogenous nitrogen sources may differently affect fungal lignocellulolytic activity. A total of 250 thermophilic fungi were isolated from local compost and vermicompost samples. First, the isolates were qualitative assayed for ligninase and cellulase activities using Congo red (CR) and carboxymethyl cellulose (CMC) as substrates, respectively. Then, twenty superior isolates harboring higher ligninase and cellulase activities were selected and quantitatively assayed for both enzymes in basic mineral (BM) liquid medium supplemented with the relevant substrates and nitrogen sources including (NH4)2SO4 (AS), NH4NO3 (AN), urea (U), AS + U (1:1), or AN + U (1:1) with final nitrogen concentration of 0.3 g/L. The highest ligninase activities of 99.94, 89.82, 95.42, 96.25, and 98.34% of CR decolorization were recorded in isolates VC85, VC94, VC85, C145, and VC85 in the presence of AS, U, AS + U, AN, and AN + U, respectively. Mean ligninase activity of 63.75% in superior isolates was achieved in the presence of AS and ranked the highest among other N compounds. The isolates C200 and C184 exhibited the highest cellulolytic activity in the presence of AS and AN + U by 8.8 and 6.5 U/ml, respectively. Mean cellulase activity of 3.90 U/mL was achieved in AN + U and ranked the highest among other N compounds. Molecular identification of twenty superior isolates confirmed that all of them are belonging to Aspergillus fumigatus group. Focusing on the highest ligninase activity of the isolate VC85 in the presence of AS, the combination can be recommended as a potential bio-accelerator for compost production.

Benign-by-design plant extract-mediated preparation of copper oxide nanoparticles for environmentally related applications.

A facile, cost-competitive, scalable and novel synthetic approach is used to prepare copper oxide (CuO) nanoparticles (NPs) using Betel leaf (Piper betle) extracts as reducing, capping, and stabilizing agents. CuO-NPs were characterized using various analytical techniques, including Fourier-transform infrared (FTIR) spectroscopy, ultraviolet-visible (UV-Vis) spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), as well as photoluminescence (PL) measurements. The activity of CuO-NPs was investigated towards Congo red dye degradation, supercapacitor energy storage and antibacterial activity. A maximum of 89% photodegradation of Congo red dye (CR) was obtained. The nanoparticle modified electrode also exhibited a specific capacitance (Csp) of 179 Fg-1. Furthermore, the antibacterial potential of CuO NPs was evaluated against Bacillus subtilis and Pseudomonas aeruginosa, both strains displaying high antibacterial performance.

Adsorption of cationic and anionic dyes onto coffee grounds cellulose/sodium alginate double-network hydrogel beads: Isotherm analysis and recyclability performance.

This work describes the preparation of new eco-friendly adsorbents with a simple method. Gel beads of coffee grounds cellulose (CGC) and sodium alginate (SA) were prepared for wastewater treatment. Upon their synthesis, the physicochemical properties, performances and efficiency were analyzed by means of various structural and morphological characterizations. Kinetic and thermodynamic adsorption approaches evaluated the removal capacity of these beads which reached equilibrium in 20 min for Methylene Blue (MB) and Congo Red (CR). Also, the kinetics shows that the results can be explained by the pseudo-second-order model (PSO). Furthermore, the isotherm assessments showed that Langmuir-Freundlich can fit the adsorption data of both contaminants. Accordingly, the maximum adsorption capacities reached by the Langmuir-Freundlich model are 400.50 and 411.45 mg/g for MB and CR, respectively. It is interesting to note that the bio-adsorption capabilities of MB and CR on bead hydrogels decreased with temperature. Besides, the results of the thermodynamic study evidenced that the bio-adsorption processes are favorable, spontaneous and exothermic. The CGC/SA gel beads are therefore outstanding bio-adsorbents, offering a great adsorptive performance and regenerative abilities.

The Potential of Congo Red Supplied Aggregates of Multitargeted Tyrosine Kinase Inhibitor (Sorafenib, BAY-43-9006) in Enhancing Therapeutic Impact on Bladder Cancer.

Bladder cancer is a common malignancy associated with high recurrence rates and potential progression to invasive forms. Sorafenib, a multi-targeted tyrosine kinase inhibitor, has shown promise in anti-cancer therapy, but its cytotoxicity to normal cells and aggregation in solution limits its clinical application. To address these challenges, we investigated the formation of supramolecular aggregates of sorafenib with Congo red (CR), a bis-azo dye known for its supramolecular interaction. We analyzed different mole ratios of CR-sorafenib aggregates and evaluated their effects on bladder cancer cells of varying levels of malignancy. In addition, we also evaluated the effect of the test compounds on normal uroepithelial cells. Our results demonstrated that sorafenib inhibits the proliferation of bladder cancer cells and induces apoptosis in a dose-dependent manner. However, high concentrations of sorafenib also showed cytotoxicity to normal uroepithelial cells. In contrast, the CR-BAY aggregates exhibited reduced cytotoxicity to normal cells while maintaining anti-cancer activity. The aggregates inhibited cancer cell migration and invasion, suggesting their potential for metastasis prevention. Dynamic light scattering and UV-VIS measurements confirmed the formation of stable co-aggregates with distinctive spectral properties. These CR-sorafenib aggregates may provide a promising approach to targeted therapy with reduced cytotoxicity and improved stability for drug delivery in bladder cancer treatment. This work shows that the drug-excipient aggregates proposed and described so far, as Congo red-sorafenib, can be a real step forward in anti-cancer therapies.

Impact of Azo Dyes and Ibuprofen on the Proteome of Serratia nematodiphila sp. MB307.

BACKGROUND: Micropollutants comprise organic/mineral substances that cause an undesirable impact on the environment, by affecting life at all scales. In this study, we explored the changes they impart on the global proteome of a soil bacterium Serratia nematodiphila MB307, for two classes of pollutants, i.e., Azo dyes (Methyl orange, Congo red) and a pharmaceutical (Ibuprofen). METHODS: The 100 µg pollutant supplemented alteration of pure S. nematodiphila MB307 culture after 24 hours of incubation at 37 °C and its control was analyzed using a differential proteomics approach. MaxQuant software with the Perseus package was used for data analysis purposes. RESULTS: Prominently, ribosomal proteins and chaperones were up or downregulated in the whole cell and membranous fraction. CONCLUSION: This illustrates dynamic protein production adaptation of bacteria, to cope with stress and cell growth/division trade-off for survival. A collective pattern of survival under stress or pollution resistance could not be decrypted for all classes of pollutants, portraying dissimilar mechanisms of coping with differently structured pollutant moieties.

Optimized synthesis of mono and bimetallic nanoparticles mediated by unicellular algal (diatom) and its efficiency to degrade azo dyes for wastewater treatment.

The silver/palladium nanoparticles (Ag/Pd NPs) were efficiently absorb UV-Visible light and reveal greater photocatalytic activity as compared to monometallic NPs. The aim of this study is photodegradation of the industrial azo dye using bimetallic Ag/Pd NPs and monometallic Ag NPs in presence of UV light for wastewater treatment. Bacillariophyceae (diatom) algae extract was utilized for the green synthesized Ag and Ag/Pd NPs. Biosynthesized nanoparticles were characterized by various useful characterization techniques viz. UV-Vis, FT-IR, SEM, TEM, and XRD. The crystallite size is found to be ∼23 nm and ∼56 nm for Ag NPs and Ag/Pd NPs, respectively, which is same as results obtained from TEM analysis, as the particle size and shape were analyzed as ∼27 and ∼56 nm, with a spherical geometry. The NPs was used to develop the optimization parameters for dye degradation such as time, temperature, and NP concentrations. A total 15 runs were considered for the study and procured by statistical software. Response surface methodology technique was implied and Box-Behnken design (BBD) design was built into the workflow. The results of the present study manifested a good connection between experimental and predicted values (R2 = 0.9838). Therefore, present study promises that the prepared NPs possess excellent photocatalytic activity against harmful dyes.

Using recycled coffee grounds for the synthesis of ZIF-8@BC to remove Congo red in water.

Around 6.6 million tons of spent coffee is produced per year, resulting in resources loss and potential environmental risks. Hence, a green technique is required to reuse the spent coffee grains. In this study, coffee grounds were burnt at 900 °C to generate the biochar (BC) for the synthesis of the porous adsorbent (ZIF-8 @BC) by growing ZIF-8 on the surface of BC. We applied the well-prepared ZIF-8 @BC to remove Congo red (CR) in water. The maximum adsorption capacity of ZIF-8 @BC on Congo red in water was up to 1080.4 mg/g, which was significantly higher than that of many different types of BCs reported in previous studies. The reasons for its highly efficient adsorption of CR probably was attributed to metal ions and coordinatively unsaturated sites in the material. Also, BC enabled the less aggregation of ZIF-8 to provide sufficient specific surface area for CR adsorption. From the analysis of the pseudo-second-order kinetic model and Langmuir model, the adsorption of ZIF-8 @BC on CR was a homogeneously chemical adsorption process regulated by electrostatic interaction, π-π stacking and metal coordination.

Recovering metal ions from oxalic acid leaching palygorskite-rich clay wastewater to fabricate layered mixed metal oxide/carbon composites for high-efficient removing Congo red.

This study developed a sustainable way to transform metallic residues in wastewater and spent adsorbents that adsorbed organic pollutants into novel high-efficiency adsorbents to treat water pollution again. The metal ions recovered from oxalic acid leaching palygorskite-rich clay wastewater was used to construct the hydrotalcite-like composites, after adsorbing organic pollutants, which was calcined and carbonized to convert into the mixed metal oxide/carbon composites (MMO/Cs). The fabricated MMO/Cs showed outstanding adsorption performance for the anionic azo dye Congo Red (CR). Especially, the MMO/C2 with the M2+/M3+ molar ratio of 2, which adjusted by supplementing Mg2+, had ultra-high adsorption capacity and ultra-clean removal efficiency for CR. The adsorption capacity was as high as 3303 mg/g, and only 0.5 g/L MMO/C2 dosing treatment for 6 h could completely decolor and remove the 2000 mg/L CR aqueous solution. Moreover, MMO/Cs exhibited the ability to simultaneous remove CR and Methylene blue (MB) mixed dye contaminants, and demonstrated the excellent recyclability. This work provides a promising method for the high-value conversion of waste resources and the synthesis of high-efficiency adsorbents.

Removal of Congo red dyes from aqueous solutions by porous γ-alumina nanoshells.

Porous alumina has been shown to be an excellent adsorbent for Congo Red (CR) dye. In this work, highly porous g-Al2O3 nanoshells were synthesized from alumina coated carbon black (CB) obtained from a new deposition technique and used for removal of CR dye from aqueous solutions. Adsorption experiments were conducted in a batch mode and a series of parameters were investigated, including contact time, initial dye concentrations, ionic strength and pH of the solutions. It was found that equilibrium for CR adsorption can be reached within 30 min, much faster than reported by other studies in the literature on similar adsorbents. It was also found that the adsorption capacity of Al2O3 nanoshells is 44.8 % higher than that of alumina/CB. The adsorption capacity of Al2O3 nanoshells was more favorable at lower pH, and the optimal adsorption ability was achieved at pH 4.0 with a removal efficiency at 98.6 %. The Al2O3 nanoshells have a maximum adsorption capacity of 370.4 mg g-1 (25 °C; pH 7; no salt added), better than or comparable to those reported in the literature. A pseudo-second-order kinetics model can best fit the kinetics of CR adsorption, which follows the Langmuir isotherm. The high adsorption capacity is attributed to the strong hydrogen-bonding interactions between the anionic dye and Al2O3 nanoshells surface as well as to the electrostatic interactions between CR dye and the Al2O3 nanoshells.

Photocatalytic degradation of congo red dye using nickel-titanium dioxide nanoflakes synthesized by Mukia madrasapatna leaf extract.

Semiconductor photocatalysts are efficient degraders of organic and inorganic waste water pollutants. Herein, we synthesized nickel-titanium dioxide (Ni-TiO2) nanoflakes using Mukia maderaspatana leafs with the aim of analyzing their photocatalytic degradation potential. Morphological analyses revealed that the nanoflakes were highly agglomerated with an average size of 100 nm. Further, elemental analysis confirmed the presence of Ti, O, and Ni, whereas Fourier transform infrared spectroscopy and X-ray diffraction established the presence of TiO2 and NiO. We found that photocatalytic degradation of congo red under UV illumination increased with increasing incubation period, demonstrating that Ni-TiO2 nanoflakes can be used as optimal photocatalysts for the degradation of dyes in waste water.

Dye-decolorization of a newly isolated strain Bacillus amyloliquefaciens W36.

Dye-decolorization is one of the most important steps in dye-polluted wastewater treatment. The dye-decolorization bacteria were isolated from active sludge collected from wastewater treating pond of a dyeing and printing plant using serial dilution method. Among the 44 bacteria isolates from the active sludge, the strain Bacillus amyloliquefaciens W36 was found to have strong ability in dye-decolorization. The effects of carbon source, nitrogen sources, C/N, metal ions, temperature, pH, and rotation speed for dye-decolorization were investigated. The optimum decolorization conditions were that the strain was grown in enriched mineral salt medium (EMSM) using maltose 1 g/L, (NH4)2SO4 1 g/L as carbon and nitrogen source respectively, supplemented with 100 mg/L different dyes (pH 6.0), at 30 °C, 200 rpm from 48 to 96 h. The bacteria could aerobically decolorize dyes, such as Coomassie brilliant blue (95.42%), Bromcresol purple (93.34%), Congo red (72.37%) and Sarranine (61.7%), within 96 h. The dyes decolorization products were analyzed by ultra-violet and visible (UV-vis) spectroscopy before and after decolorization, which indicated that the four dyes were significantly degraded by the strain. The results indicated that the bacteria Bacillus amyloliquefaciens W36 could be used in dye-polluted wastewater treatment.

Influence of selenium precursors on the formation of iron selenide nanostructures (FeSe2): Efficient Electro-Fenton catalysts for detoxification of harmful organic dyestuffs.

In this investigation, a sequences of iron diselenide (FeSe2) nanomaterials as the competent and highly stable catalysts for the detoxification of aqueous organic dye pollutants such as Congo red (CR) and methylene blue (MB) through Electro-Fenton (EF) process using hydrogen peroxide as an initiator have been studied. The utilized selenium precursors include selenium metal, selenious acid (H2SeO3) and selenium dioxide (SeO2) which were employed for the synthesis of FeSe2 catalysts through a wet chemical strategy. It has been observed that based on the employed precursors, different morphologies ranges of the FeSe2 catalysts were obtained: microgranualr particles to nano-stick to nanoflakes. The crystalline nature and phase purity of the obtained FeSe2 catalysts were determined through XRD, Raman and HR-TEM analyses which confirmed their orthorhombic ferroselite structure. Among the prepared FeSe2 catalysts, FS-2 (using H2SeO3) displayed better porous properties as compared to other catalysts and achieved the highest surface area of 74.68 m2g-1. The narrow bandgap (0.88 eV) and fast conversion of Fe2+/Fe3+ cycle of FeSe2 led CR and MB degradation of 93.3% and 90.4%, respectively. The outcome of this study demonstrates improved catalytic properties of FeSe2 nanostructures for the efficient detoxification of hazardous and toxic effluents.

Antibacterial Therapy by Ag+ Ions Complexed with Titan Yellow/Congo Red and Albumin during Anticancer Therapy of Urinary Bladder Cancer.

According to the World Health Organization report, the increasing antibiotic resistance of microorganisms is one of the biggest global health problems. The percentage of bacterial strains showing multidrug resistance (MDR) to commonly used antibiotics is growing rapidly. Therefore, the search for alternative solutions to antibiotic therapy has become critical to combat this phenomenon. It is especially important as frequent and recurring infections can cause cancer. One example of this phenomenon is urinary tract infections that can contribute to the development of human urinary bladder carcinoma. This tumor is one of the most common malignant neoplasms in humans. It occurs almost three times more often in men than in women, and in terms of the number of cases, it is the fifth malignant neoplasm after prostate, lung, colon, and stomach cancer. The risk of developing the disease increases with age. Despite the improvement of its treatment methods, the current outcome in the advanced stages of this tumor is not satisfactory. Hence, there is an urgent need to introduce innovative solutions that will prove effective even in the advanced stage of the disease. In our study, a nanosystem based on ionic silver (Ag+) bound to a carrier-Titan yellow (TY) was analyzed. The possibility of binding the thus formed TY-Ag system to Congo red (CR) and albumin (BSA) was determined. TY-Ag binding to CR provides for better nanosystem solubility and enables its targeted intracellular transport and binding to immune complexes. The binding of TY-Ag or CR-TY-Ag to albumin also protects the system against the uncontrolled release of silver ions. It will also allow the delivery of silver in a targeted manner directly to the desired site in the case of intravenous administration of such a system. In this study, the MIC (Minimum Inhibitory Concentration) and MBC (Minimum Bactericidal Concentration) values of the TY-Ag or BSA-TY-Ag systems were determined in two reference strains (Escherichia coli and Staphylococcus aureus). The paper presents nanosystems with a size of about 40-50 nm, with an intense antibacterial effect obtained at concentrations of 0.019 mM. We have also discovered that TY-Ag free or complexed with BSA (with a minimal Ag+ dose of 15-20 µM) inhibited cancer cells proliferation. TY-Ag complex diminished migration and effectively inhibited the T24 cell viability and induced apoptosis. On the basis of the obtained results, it has been shown that the presented systems may have anti-inflammatory and antitumor properties at the same time. TY-Ag or BSA-TY-Ag are new potential drugs and may become in future important therapeutic compounds in human urinary bladder carcinoma treatment and/or potent antimicrobial factors as an alternative to antibiotics.

Coffee extracts effectively inhibit the formation of α-chymotrypsin amyloid-like fibrils in aqueous ethanol in vitro.

In this study, an in vitro α-chymotrypsin aggregation model was used to demonstrate that certain extracts of commercial coffees effectively inhibit protein aggregation in 55% ethanol at pH 7.0. To detect the anti-amyloidogenic effect of the various coffee extracts, turbidity measurements and Congo red binding assays were performed as well as the determination of the total polyphenol content of the extracts. The greatest fibril formation inhibitory effect was exerted by the Eduscho coffee extract, which contained also the most of the phenolic compounds. The Eduscho coffee extract inhibited the fibrillation of the α-chymotrypsin dose dependently. Coffee extracts are effective anti-aggregation agents, and their beneficial effects strongly correlate with the total phenolic content.

Betanin assisted synthesis of betanin@silver nanoparticles and their enhanced adsorption and biological activities.

Natural red purple dye, Betanin, was extracted from the beetroot, purified by aqueous two- phase extraction and gel permeation column chromatography, and used as a reducing agent for the synthesis of silver-betanin core-shell triangular nanodisks for the first time. Spectroscopic data show that the nanoparticle structure is core@shell like with Ag as core and betanin as shell. Langmuir monolayer model (qm = 32.4 mg/g, RL = 0.99 and R2 = 0.997) was the best fit adsorption isotherm for the dye removal. Adsorption kinetics is well explained by pseudo-second-order equation. Gibbs free energy (ΔG0 = -2.59 kJ mol-1), enthalpy (ΔH0 = 18.05 kJ mol-1), and entropy (ΔS0 = 68.92 J/K/mol) were calculated and discussed. The antibacterial activity of betanin-AgNPs were determined against Escherichia coli MTCC-450 (E. coli) and Staphylococcus aureus MTCC-3160 (S. aureus) bacteria.

Characterization, antioxidant and hypoglycemic activities of degraded polysaccharides from blackcurrant (Ribes nigrum L.) fruits.

In this study, the degradation of polysaccharides from blackcurrant (BCP) was investigated. Two low-molecular-weight polysaccharides (DBCP-1, DBCP-2) were obtained using Fe2+ with different concentrations of H2O2 solution. IR spectra showed DBCPs had obvious characteristic peaks of polysaccharides. GC analysis confirmed DBCPs were composed of the same monosaccharide units as BCP but with different molar ratios. NMR analysis indicated DBCPs and BCP had similar glycosidic linkage patterns. The surface area of fragmented structure in DBCPs was reduced compared to BCP, and they had no triple helix structure. The results of bioactivity assays indicated that DBCPs exhibited higher antioxidant, α-amylase and α-glucosidase inhibitory activities than BCP, and the degraded polysaccharides with the lower molecular weight possessed higher bioactivities. These results suggested that Fe2+-H2O2 degradation did not change the main structure of polysaccharide and the degree of degradation could play a key role in the bioactivities of the polysaccharides.

Identification of a Multicomponent Traditional Herbal Medicine by HPLC-MS and Electron and Light Microscopy.

BACKGROUND: Commercial pharmaceutical herbal products have enabled people to take traditional Chinese medicine (TCM) in a convenient and accessible form. However, the quantity and quality should be additionally inspected. To address the issue, a combination of chemical and physical inspection methods were developed to evaluate the amount of an herbal formula, Xiang-Sha-Liu-Jun-Zi-Tang (XSLJZT), in clinical TCM practice. METHODS: A high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS) method with electrospray ionization was developed to measure the herbal biomarkers of guanosine, atractylenolide III, glycyrrhizic acid, dehydrocostus lactone, hesperidin, and oleanolic acid from XSLJZT. Scanning electron microscopy (SEM) photographs and light microscopy photographs with Congo red and iodine-KI staining were used to identify the cellulose fibers and starch content. Furthermore, solubility analysis, swelling power test, and crude fiber analysis were contributed to measure the starch additive in pharmaceutical products. RESULTS: The results demonstrated large variations in the chemical components of different pharmaceutical brands. The SEM photographs revealed that the starch was oval, smooth, and granular, and that the raw herbal powder appears stripy, stretched, and filiform. The stained light microscopy photographs of all of the pharmaceutical products showed added starch and raw herbal powder as extenders. CONCLUSION: The developed chemical and physical methods provide a standard operating procedure for the quantity control of the herbal pharmaceutical products of XSLJZT.

Degradation of anthropogenic pollutant and organic dyes by biosynthesized silver nano-catalyst from Cicer arietinum leaves.

The work represents the potent catalytic activity of silver nanoparticles synthesized from Cicer arietinum (chickpea) leaf extract (CAL-AgNPs). Here, silver nano-catalysts were used against the anthropogenic pollutants mainly involving nitro-amines and azo dyes. These pollutants are extremely harmful to our environment and causes severe health issues. The CAL-AgNPs have the potential to degrade harmful toxins and their by-products, thereby decreasing the pollutants from the environment. The green synthesis of nano-catalyst includes a simple, cost effective and eco-friendly method using the leaf extract from the plant. A systematic study was conducted, including synthesis, optimization and characterization of the silver particles. The AgNPs were further assessed through DLS and TEM for size and morphological evaluation. The obtained particles have shown spherical morphology with the size range of 88.8nm. Further, FTIR were performed for compositional and functional group analysis of the particles. The antibacterial efficiency was also evaluated against E. coli and P. aeruginosa. For their catalytic evaluation, CAL-AgNPs were assessed for 4-nitrophenol, methylene blue and congo red. The results obtained through catalytic evaluation suggested that the CAL-AgNPs could be helpful to surmount the environmental pollution in a very effective manner.