Role of plasma process gas on permeate flux augmentation of cellulose nitrate membrane for mud water treatment.

A comparative study between Nitrogen (N2) and Argon (Ar) plasma is carried out to investigate its effect on surface morphology, hydrophilicity, permeate flux and ageing of cellulose nitrate polymeric membranes in the present work. Langmuir probe and Optical Emission Spectroscopy are used to characterize the plasma. The SEM analysis reveals the noticeable macro-void creations and pore enlargement for both N2 and Ar plasma. The AFM analysis shows a higher surface roughness for Ar plasma treatment as compared to N2 plasma treatment. XPS analysis confirms the changes in the polymer matrix along with the incorporation of various functional groups on the membrane surface as a result of the plasma treatment. A better hydrophilic nature with prolonged plasma treatment is observed for Ar plasma as compared to N2 plasma treatment. The present results show a higher permeate flux with a high rejection rate for Ar plasma treatment in comparison to N2 plasma, which might be due to the pore size and pore area enlargement of the membrane. The hydrophobic recovery for both the plasma-treated membranes is found significant for the initial ageing period of 7 days and found almost stable in nature after 7 days. A diffusion-based theoretical model is developed to study the hydrophobic recovery of plasma-treated membranes. A strong alignment between experimental and theoretical results is observed in the present work. The Cake Filtration model, derived from the Hermia model, is identified as the most suitable model for describing the fouling mechanisms for the present work.

Post-treatment of soft drink industrial wastewater using a new antibacterial ultra-filtration membrane prepared of Polyethersulfone blended with boehmite-tannic acid-graphene quantum dot.

Polymeric membranes have garnered great interest in wastewater treatment; however, fouling is known as their main limitation. Therefore, the blending of hydrophilic nanoparticles in polymeric membranes' structure is a promising approach for fouling reduction. Herein, a hydrophilic boehmite-tannic acid-graphene quantum dot (BM-TA-GQD) nanoparticle was synthesized and blended in a polyethersulfone polymeric membrane in different percentages. The fabricated membranes were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) images, water contact angle, porosity measurement, and antibacterial and antifouling properties. Surface SEM images of the modified membranes showed good dispersion of nanoparticles up to 0.5 wt%, which resulted in hydrophilicity and pure water flux enhancement. Based on AFM images, the mean roughness (Sa) of the fabricated membranes decreased from 2.07 to 0.84 nm for the bare and optimum membranes, respectively. In terms of performance, increasing the nanoparticle percentages up to 0.5 wt% resulted in the flux recovery ratio developing from 44.58% for the bare membrane to 71.35% for the 0.5 wt% BM-TA-GQD/PES membrane (optimum membrane). The antibacterial property of fabricated membranes was studied against biologically treated soft drink industrial wastewater (BTSDIW) as a bacterial source. The results showed that the turbidity of solutions containing permeated wastewater from the modified membranes (0.1, 0.5, and 1 wt% of BM-TA-GQD) was lower than that obtained from the unmodified membrane. These results confirmed the antibacterial properties of fabricated membranes. Finally, the optimal membrane (0.5 wt% BM-TA-GQD) was examined for post-treatment of the BTSDIW. An effluent COD of 13 mg/L and turbidity of 2 NTU showed a successful performance of the filtration process. PRACTITIONER POINTS: Ultrafiltration PES membranes were modified by different loadings of BM-TA-GQD. Hydrophilicity improvement was achieved by adding BM-TA-GQD nanoparticles. Expansion of size and number of macro-voids in modified membranes was confirmed. Membrane roughness was reduced in the BM-TA-GQD blended membranes. The optimum membrane was efficient in COD and turbidity removal.

CO2-triggered switchable hydrophilicity solvent as a recyclable extractant for ultrasonic-assisted extraction of Polygonatum sibiricum polysaccharides.

In this study, CO2-triggered switchable hydrophilicity solvents (SHSs) based on different amines and water were employed in the ultrasonic-assisted extraction of Polygonatum sibiricum polysaccharides (PSPs). When CO2 was pumped into the amine, the solution became hydrophilic and could be used as an extractant for PSPs extraction. When CO2 was removed, the solution switched hydrophobicity, with the extractants being separated from the extract and further recycled and reused. The factors affecting the solid-liquid extraction of PSPs were studied. The maximum extraction yield of 399.2 mg/g was obtained at a solid-liquid ratio of 1:20, extraction time of 60 min, extraction temperature of 50 °C, and ultrasonic power of 500 W. SHSs could be recovered and reused with 88.4% recovery after the fifth cycle. The molecular weights and monosaccharide compositions of PSPs were also determined. This study provides a new strategy for sustainable extraction of plant polysaccharides and other bioactive ingredients.

Effect of Glycerol Concentrations on the Characteristics of Cellulose Films from Cattail (Typha angustifolia L.) Flowers.

Plastic waste has become a big problem for the environment globally. Biodegradable polymers are a potential replacement for plastics that can have a positive outcome both environmentally and economically. In this work, we used acid hydrolysis and alkaline treatment to extract cellulose fibers from cattails. The obtained cellulose was used as a substrate for the fabrication of cellulose film using a casting technique on plastic plates. Different concentrations of the plasticizer, glycerol, were used to prepare films for comparison, and its effects on the film's characteristics were observed. The morphology, chemical structure, and thermal stability of the cattail cellulose (CTC) films were studied using techniques such as scanning electron microscopy (SEM), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and thermogravimetric analysis (TGA), respectively. Measurements of transparency, moisture content (MC), water solubility (MS), and water contact angle (WCA) were also performed. Introducing glycerol into the films increased the transparency, MC, and WS values, as well as the gap width between film textures. However, it resulted in a decrease in the WCA of the films, showing that the hydrophilicity of the films is increased by the addition of glycerol. The interaction between the functional groups of cellulose and glycerol was established from the ATR-FTIR and XRD data. The obtained results indicated that glycerol affected the thermal stability and the degree of crystallinity of the produced films. Accordingly, the hydrophilicity of the cellulose film was increased by increasing the glycerol content; therefore, cattail cellulose films can be used as a biodegradable alternative to plastic in the future.

Poly(Butylene Adipate/Terephthalate-Co-Glycolate) Copolyester Synthesis Based on Methyl Glycolate with Improved Barrier Properties: From Synthesis to Structure-Property.

The main problem of manufacturing with traditional biodegradable plastics is that it is more expensive than manufacturing with polymers derived from petroleum, and the application scope is currently limited due to poor comprehensive performance. In this study, a novel biodegradable poly(butylene adipic acid/terephthalate-co-glycolic acid) (PBATGA) copolyester with 25-60% glycolic acid units was successfully synthesized by esterification and polycondensation using cheap coal chemical byproduct methyl glycolate instead of expensive glycolic acid. The structure of the copolyester was characterized by ATR-FTIR, 1H NMR, DSC, and XRD; and its barrier property, water contact angle, heat resistance, and mechanical properties were tested. According to the experiment result, the PBATGA copolyesters showed improved oxygen (O2) and water vapor barrier character, and better hydrophilicity when compared with PBAT. The crystallization peaks of PBATGAs were elevated from 64 °C to 77 °C when the content of the GA unit was 25 mol %, meanwhile, the elongation at the break of PBATGA25 was more than 1300%. These results indicate that PBATGA copolyesters have good potentiality in high O2 and water vapor barrier and degradable packaging material.

Bubbles help male flowers overcome obstacles during pollination in Hydrilla verticillata.

PREMISE: Pollination in many aquatic plants takes place on the water surface, and the male flowers or stamens often produce gas bubbles underwater; however, the generation mechanism and function of these bubbles are unknown. METHODS: A common submerged plant, Hydrilla verticillata, was used as experimental material to observe the structure of male flowers, analyze the process of bubble generation, and simulate the movement process of the male flower with attached gas bubble in water. RESULTS: The aerenchyma inside the male plants of H. verticillata transported the gas produced by the plant's branches during photosynthesis to the male flower, and the formed gas bubbles became attached to the edge of the perianth. The gas accumulation rate in the attached bubbles increased with light intensity. Once the bubble diameter increased to approximately 3.3 mm, the male flowers with the bubble detached from the plant and floated to the water surface. The removal of the attached bubbles did not affect the male flower detached from the plant; however, the surfacing of male flowers without gas bubbles was easily prevented by the plant's branches in the water, and they could not reach the water surface to complete pollen dispersal. CONCLUSIONS: The gas bubbles produced by male flowers of H. verticillata came from the gas produced by branches under light. These bubbles can help ascending male flowers bypass the obstacles in water and reach the surface to complete pollination.

Silica deposition on zirconia via room-temperature atomic layer deposition (RT-ALD): Effect on bond strength to veneering ceramic.

PURPOSE: To develop and to characterize a hybrid interface between yttria-stabilized zirconia (Y-TZP) transformed layer and silica-based nanofilm to enable a better bonding between Y-TZP and a veneering ceramic. MATERIAL AND METHODS: Sixty-six fully-sintered rectangular Y-TZP specimens were distributed into 6 groups, according to the surface treatment applied: C (control): no treatment; Al: 27 µm-alumina particle abrasion; Ht: hydrothermal treatment in autoclave for 15h; Si20: 20 cycles of silica deposition using room-temperature atomic layer deposition (RT-ALD); Si40: 40 cycles of RT-ALD; Ht + Si40: hydrothermal treatment followed by 40 cycles of RT-ALD. RT-ALD was performed by the sequential exposure of specimens to vapor of tetramethoxysilane orthosilicate (TMOS) and ammonium hydroxide (NH4OH). Y-TZP surface wettability and shear bond strength (SBS) between Y-TZP and the veneering ceramic were analyzed for all groups after surface treatments. One-way ANOVA and Tukey's HSD test were used for data analysis (p ≤ 0.05). RESULTS: The highest contact angle was observed for the control group (64.46 ± 6.09 θ), while the lowest values (p < 0.001) were presented after Si20 (29.85 ± 4.23 θ) and Si40 (30.37 ± 5.51 θ) treatments. Hydrothermal treatment (49.3 ± 2.69 θ) and alumina abrasion (45.84 ± 4.12 θ) resulted in intermediate contact angle values. The highest SBS values were observed for Al (16.74 ± 1.68 MPa) and Ht (15.27 ± 2.11 MPa) groups (p < 0.018). Groups Si20 (9.66 ± 1.22 MPa), Si40 (9.33 ± 2.11 MPa), Ht + Si40 (9.37 ± 1.02 MPa) and C (12.54 ± 2.64 MPa) all resulted in similar SBS results (p > 0.998). CONCLUSION: The experimental treatments proposed enhanced surface wettability, but shear bond strength between Y-TZP and veneering ceramic was not improved. Alumina particle-abrasion improved SBS values while a decrease in wettability was observed.

[Preparation of hydrophilic Indigo Naturalis based on polyethylene glycol( PEG) surface film-forming method and evaluation].

Polyethylene glycol (PEG) surface film-forming method was used to prepare hydrophilic Indigo Naturalis decoction pieces with stable effect.The preparation process of modified Indigo Naturalis was optimized and its microscopic properties,hydrophilicity,antipyretic efficacy,and safety were systematically evaluated.With equilibrium contact angle as assessment index,the influence of modifier type,modifier dosage,dispersant dosage,and co-grinding time on water solubility of Indigo Naturalis was investigated by single factor test.The results showed that the optimal preparation process was as follows.The 6%PEG6000 is dissolved in 10%anhydrous ethanol solution by sonification and then the mixture is ground with Indigo Naturalis for 2 min.The resultant product is dried on a square tray in an oven at 60℃to remove ethanol and thereby the PEG-modified hydrophilic Indigo Naturalis decoction pieces are yielded.The morphological observation under scanning electron microscope (SEM) indicated that the modified Indigo Naturalis had smoother surface than Indigo Naturalis,and energy spectrometer measurement showed that the nitrogen (N),calcium(Ca),oxygen (O),and silicon (Si) on the surface of modified Indigo Naturalis powder were less than those of Indigo Naturalis powder.Modified Indigo Naturalis had the equilibrium contact angle 18.96°smaller,polar component 22.222 m J·m~(-2)more,and nonpolar component 7.277 m J·m~(-2)smaller than the Indigo Naturalis powder.Multiple light scattering technique was employed to evaluate the dispersion in water and the result demonstrated that the transmittance of Indigo Naturalis and modified Indigo Naturalis was about85%and 75%,respectively,suggesting the higher dispersity of modified Indigo Naturalis.The suspension rate of modified Indigo Naturalis in water was determined by reflux treatment.The result showed that 57%of Indigo Naturalis was not wetted after refluxing for1 h,while the modified Indigo Naturalis was all wetted and dispersed into water.The dissolution of indigo and indirubin of modified Indigo Naturalis increased and the process was more stable.Then,rats were randomized into the blank group,model group,acetaminophen group,Indigo Naturalis group,and hydrophilic Indigo Naturalis group.The temperature changes of rats were observed after administration and the concentration of IL-1ßand TNF-αin serum and IL-1ßand PGE_2in hypothalamus was measured.The results indicated that the temperature of Indigo Naturalis group and hydrophilic Indigo Naturalis group dropped and the IL-1ßlevel of the hydrophilic Indigo Naturalis group decreased (P<0.05) as compared with those in the model group.Thus,both Indigo Naturalis and hydrophilic Indigo Naturalis had antipyretic effect,particularly the hydrophilic Indigo Naturalis.The acute toxicity test of hydrophilic Indigo Naturalis verified that it had no toxicity to rats.In this study,the hydrophilic Indigo Naturalis decoction pieces were prepared with the PEG surface film-forming method,and the antipyretic efficacy and safety were evaluated,which expanded the technological means of powder modification for Chinese medicine and provided a method for clinical use of Chinese medicine.

Fabrication of zinc doped aluminium oxide/polysulfone mixed matrix membranes for enhanced antifouling property and heavy metal removal.

Heavy metal removal from water resources is essential for environmental protection and the production of safe drinking water. In this direction, Zinc doped Aluminium Oxide (Zn:Al2O3) nanoparticles were incorporated into Polysulfone (PSf) to prepare mixed matrix membranes for the efficient removal of heavy metals from water. These Zn:Al2O3 nanoparticles prepared by the solution combustion method have a very high surface area (261.44 m2/g) with an approximate size of 50 nm. X-ray Photoelectron Spectroscopy analysis showed that the Al and Zn were in +3 and + 2 oxidation states, respectively. Cross-sectional Scanning Electron Microscopy images revealed the finger-like morphology and porous nature of the membranes. In this study, the optimum loading amount of Zn:Al2O3 nanoparticles was determined. Synthesized membranes showed enhanced hydrophilicity, surface charge, and porosity, which enabled the removal of arsenic and lead with efficiencies of 87% and 98%, respectively. A study of the antifouling properties carried out at various pressures with a feed solution containing Bovine Serum Albumin (BSA) showed 98.4% of flux recovery ratio and reusability up to three continuous cycles. Moreover, this work demonstrates a rational design of novel mixed matrix membranes exhibiting characteristics of hydrophilicity, surface charge, and porosity adequate to realize the efficient removal of heavy metals.

Preparation of hydrophilic Indigo Naturalis based on polyethylene glycol( PEG) surface film-forming method and evaluation / 中国中药杂志

Polyethylene glycol (PEG) surface film-forming method was used to prepare hydrophilic Indigo Naturalis decoction pieces with stable effect.The preparation process of modified Indigo Naturalis was optimized and its microscopic properties,hydrophilicity,antipyretic efficacy,and safety were systematically evaluated.With equilibrium contact angle as assessment index,the influence of modifier type,modifier dosage,dispersant dosage,and co-grinding time on water solubility of Indigo Naturalis was investigated by single factor test.The results showed that the optimal preparation process was as follows.The 6%PEG6000 is dissolved in 10%anhydrous ethanol solution by sonification and then the mixture is ground with Indigo Naturalis for 2 min.The resultant product is dried on a square tray in an oven at 60℃to remove ethanol and thereby the PEG-modified hydrophilic Indigo Naturalis decoction pieces are yielded.The morphological observation under scanning electron microscope (SEM) indicated that the modified Indigo Naturalis had smoother surface than Indigo Naturalis,and energy spectrometer measurement showed that the nitrogen (N),calcium(Ca),oxygen (O),and silicon (Si) on the surface of modified Indigo Naturalis powder were less than those of Indigo Naturalis powder.Modified Indigo Naturalis had the equilibrium contact angle 18.96°smaller,polar component 22.222 m J·m~(-2)more,and nonpolar component 7.277 m J·m~(-2)smaller than the Indigo Naturalis powder.Multiple light scattering technique was employed to evaluate the dispersion in water and the result demonstrated that the transmittance of Indigo Naturalis and modified Indigo Naturalis was about85%and 75%,respectively,suggesting the higher dispersity of modified Indigo Naturalis.The suspension rate of modified Indigo Naturalis in water was determined by reflux treatment.The result showed that 57%of Indigo Naturalis was not wetted after refluxing for1 h,while the modified Indigo Naturalis was all wetted and dispersed into water.The dissolution of indigo and indirubin of modified Indigo Naturalis increased and the process was more stable.Then,rats were randomized into the blank group,model group,acetaminophen group,Indigo Naturalis group,and hydrophilic Indigo Naturalis group.The temperature changes of rats were observed after administration and the concentration of IL-1βand TNF-αin serum and IL-1βand PGE_2in hypothalamus was measured.The results indicated that the temperature of Indigo Naturalis group and hydrophilic Indigo Naturalis group dropped and the IL-1βlevel of the hydrophilic Indigo Naturalis group decreased (P<0.05) as compared with those in the model group.Thus,both Indigo Naturalis and hydrophilic Indigo Naturalis had antipyretic effect,particularly the hydrophilic Indigo Naturalis.The acute toxicity test of hydrophilic Indigo Naturalis verified that it had no toxicity to rats.In this study,the hydrophilic Indigo Naturalis decoction pieces were prepared with the PEG surface film-forming method,and the antipyretic efficacy and safety were evaluated,which expanded the technological means of powder modification for Chinese medicine and provided a method for clinical use of Chinese medicine.

Recycling of phosphorus-containing plastic based on the dual effects of switchable hydrophilicity solvents.

Plastic waste has caused severe environmental problems. Some additives in plastics, like organophosphates, enter the environment with plastic waste, causing significant harm to plants and creatures. However, the primary method of recycling phosphorus-containing plastic, especially polycarbonate and acrylonitrile-butadiene-styrene copolymer (PC/ABS), is a mechanical method, which not only does not effectively separate plastics and organophosphates but also tends to cause polymer degradation during recycling. In order to overcome these problems, we proposed an efficient and sustainable approach to recycle of phosphorus-containing plastic. In this method, N, N-dimethylcyclohexylamine (DMCHA), a switchable hydrophilicity solvent (SHS), was used to react with and extract organophosphates in plastic, achieving the goal of complete separation of plastic and organophosphates. PC/ABS can be recovered by precipitation. Dissolved organophosphates can also be easily recovered due to the switching characteristics of SHS. Both of recovered materials were of high purity and were close to virgin materials. This technique is an easy and efficient approach to separate plastic and organophosphates, which has excellent application prospects in recycling phosphorus-containing plastic.

Hydrothermal treatment of etched titanium: A potential surface nano-modification technique for enhanced biocompatibility.

Nanoengineering the topology of titanium (Ti) implants has the potential to enhance cytocompability and biocompatibility properties as implant surfaces play a decisive role in determining clinical success. Despite developments in various surface engineering strategies, antibacterial properties of Ti still need to be enhanced. Here a facile, cost-effective hydrothermal route was used to develop nano-patterned structures on a Ti surface. Changing hydrothermal treatment parameters such as temperature, pressure, and time, resulted in various topographies, crystal phases, and hydrophobicity. Specifically, hydrothermal treatment performed at 225 °C for 5 h, presented a novel topography with nanoflower features, exhibited no mammalian cell cytotoxicity for a time period of 14 days, and increased calcium deposition from osteoblasts. Treated samples also demonstrated antibacterial properties (without resorting to the use of antibiotics) against Staphylococcus aureus and methicillin resistant Staphylococcus aureus. In conclusion, hydrothermal oxidation on an etched Ti surface can generate surface properties that have excellent prospects for the biomedical field.

Niobium treated by Plasma Electrolytic Oxidation with calcium and phosphorus electrolytes.

Niobium plates were electrochemically treated by Plasma Electrolytic Oxidation (PEO) with electrolytes containing phosphorous and/or calcium. Three different electrolyte and experimental parameters were used forming three different surfaces. Film morphology, thickness, and chemical composition were analyzed by scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS). A profilometer and the sessile drop technique measured the average surfaces roughness (Ra) and contact angles respectively. X-ray diffraction technique (XRD) analyzed the oxide crystallinity, and scratch tests evaluated the film adhesion. All oxidized surfaces presented pores, without observed cracks. Comparing the different experimental conditions, films obtained with phosphoric acid (P100) show superficial pores, phosphorus incorporation, high hydrophilicity, non-crystalline oxide formation, and good scratch resistance. Films treated with calcium acetate electrolyte (Ca100), compared to P100 exhibit smaller size pores and film thickness, smaller hydrophilicity, and lower scratch resistance. They also demonstrated higher oxide crystallinity, calcium incorporation, and pores interconnections. When the PEO was executed with a blended electrolyte containing calcium acetate and phosphoric acid (Ca50P50) the formed films presented the highest thickness, high phosphorus incorporation, and the lowest contact angle compared with other films. In addition, the pores size, the scratch resistance, calcium incorporation, and oxide crystallinity present intermediate values compared to P100 and Ca100 films. Film crystallinity seems to be influenced by calcium incorporation, whereas, hydrophilicity is phosphorus amount dependent. The pores amount and their interconnections reduced the scratch resistance. Surface features obtained in this work are largely mentioned as positive characteristics for osseointegration processes.

Immunomodulatory Properties of Plants and Mushrooms.

Plants and mushrooms are used for medicinal purposes and the screening of molecules possessing biological activities. A single plant or mushroom may produce both stimulatory and inhibitory effects on immune cells, depending on experimental conditions, but the reason behind this dichotomy remains obscure. We present here a large body of experimental data showing that water extracts of plants and mushrooms usually activate immune cells, whereas ethanol extracts inhibit immune cells. The mode of extraction of plants and mushrooms may thus determine the effects produced on immune cells, possibly due to differential solubility and potency of stimulatory and inhibitory compounds. We also examine the possibility of using such plant and mushroom extracts to treat immune system disorders.

A NIR-controlled cage mimicking system for hydrophobic drug mediated cancer therapy.

Most chemotherapeutic drugs commonly suffer from several shortcomings, including the lack of aqueous solubility, limited stability and adverse side effects. Although caging strategy has recently been employed as an effective approach to conceal and stabilize these drugs to achieve light-activated cancer therapy, it is plagued by the sophisticated drug modification process and deleterious solvent usage. In addition, using UV or Visible light to remove photocaged group is restricted to its limited tissue penetration ability in and phototoxicity. In this paper, by anchoring photochromic spiropyran on the mesoporous silica coated upconversion nanoparticles (UCNP-SP), we design a NIR-controlled cage mimicking system. Our results indicate that hydrophobic drug can be concealed inside the channels of the nanocarrier with high stability and "uncaged" via NIR irradiation-triggered hydrophobicity-hydrophilicity switch of the spiropyran molecules, finally inducing drug release and recovering their bioactivity. Moreover, under NIR illumination, the UV/Visible emissions from UCNP can also efficaciously initiate the generation of reactive oxygen species (ROS) by Curcumin, further improving the therapeutic efficiency. Both in vitro and in vivo experimental results validate that NIR irradiated nanosystem can produce remarkably enhanced antitumor efficiency.

Treatment of table olive processing wastewaters using novel photomodified ultrafiltration membranes as first step for recovering phenolic compounds.

Table olive processing wastewaters (TOPW) have high salt concentration and total phenolic content (TPC) causing many environmental problems. To reduce them, ultrafiltration (UF) was applied for treating TOPW. However, NaCl, which is the main responsible of salinity in TOPW, and phenols are small molecules that cannot be separated by conventional UF membranes. They have serious problems caused by fouling, which can be overcome using membrane modification techniques. For these reasons, photomodification may be an effective technique to obtain a stream rich in TPC due to the changes in membrane surface properties. UV-modification in the presence of two hydrophilic compounds (polyethylene glycol and aluminium oxide) was performed to achieve membranes with high reductions of organic matter and to keep the TPC as high as possible. Commercial polyethersulfone (PES) membranes of 30 kDa were used. Surface modification was evaluated using FTIR-ATR spectroscopy and membrane performance was studied by calculating the rejection ratios of colour, chemical oxygen demand (COD) and TPC. Results demonstrated that UF is a useful pre-treatment to reduce organic matter from TOPW, obtaining a permeate rich in TPC. PES/Al2O3 membranes displayed superior antifouling properties and rejection values, keeping high the TPC (>95%). Therefore, UF using modified membranes is an appropriate and sustainable technique for treating TOPW.

In situ measurements of thin films in bovine serum lubricated contacts using optical interferometry.

The aim of this study is to consider the relevance of in situ measurements of bovine serum film thickness in the optical test device that could be related to the function of the artificial hip joint. It is mainly focussed on the effect of the hydrophobicity or hydrophilicity of the transparent surface and the effect of its geometry. Film thickness measurements were performed using ball-on-disc and lens-on-disc configurations of optical test device as a function of time. Chromatic interferograms were recorded with a high-speed complementary metal-oxide semiconductor digital camera and evaluated with thin film colorimetric interferometry. It was clarified that a chromium layer covering the glass disc has a hydrophobic behaviour which supports the adsorption of proteins contained in the bovine serum solution, thereby a thicker lubricating film is formed. On the contrary, the protein film formation was not observed when the disc was covered with a silica layer having a hydrophilic behaviour. In this case, a very thin lubricating film was formed only due to the hydrodynamic effect. Metal and ceramic balls have no substantial effect on lubricant film formation although their contact surfaces have relatively different wettability. It was confirmed that conformity of contacting surfaces and kinematic conditions has fundamental effect on bovine serum film formation. In the ball-on-disc configuration, the lubricant film is formed predominantly due to protein aggregations, which pass through the contact zone and increase the film thickness. In the more conformal ball-on-lens configuration, the lubricant film is formed predominantly due to hydrodynamic effect, thereby the film thickness is kept constant during measurement.

Understanding the wetting properties of nanostructured selenium coatings: the role of nanostructured surface roughness and air-pocket formation.

Wetting properties of biomaterials, in particular nanomaterials, play an important role, as these influence interactions with biological elements, such as proteins, bacteria, and cells. In this study, the wetting phenomenon of titanium substrates coated with selenium nanoparticles was studied using experimental and mathematical modeling tools. Importantly, these selenium-coated titanium substrates were previously reported to increase select protein adsorption (such as vitronectin and fibronectin), to decrease bacteria growth, and increase bone cell growth. Increased selenium nanoparticle coating density resulted in higher contact angles but remained within the hydrophilic regime. This trend was found in disagreement with the Wenzel model, which is widely used to understand the wetting properties of rough surfaces. The trend also did not fit well with the Cassie-Baxter model, which was developed to understand the wetting properties of composite surfaces. A modified wetting model was thus proposed in this study, to understand the contributing factors of material properties to the hydrophilicity/hydrophobicity of these nanostructured selenium-coated surfaces. The analysis and model created in this study can be useful in designing and/or understanding the wetting behavior of numerous biomedical materials and in turn, biological events (such as protein adsorption as well as bacteria and mammalian cell functions).