Precise evaluation of batch adsorption kinetics of plant total polyphenols based on a flow-injection online spectrophotometric method.

Efficient evaluation of adsorption kinetics of plant total polyphenols is essential for the design of adsorption separation of bioactive compounds. The conventional method uses manual sampling with poor reproducibility. Here, we developed a new method for on-line determination of total polyphenol content (TPC) in plant extracts by applying the Folin-Ciocalteu method in flow-injection analysis (FIA). The FIA parameters were optimized and a standard curve with excellent linearity was established. Precise determination of TPC with a satisfactory sample throughput of 20 h-1 was achieved for the adsorption kinetic study. The pseudo-second-order kinetic model was found to better describe the kinetic parameters of the batch adsorption/desorption process. The developed method proved to be accurate compared with the conventional method. The FIA method holds significant promise for studying and monitoring adsorption processes, due to its automatic on-line nature, low consumption of reagents and samples, and the ability to generate large quantities of highly accurate adsorption data.

The Determination Method of Total Polyphenol in Tea and Substitute Tea Based on [Ag(HIO6)2]5--Luminol Chemiluminescence System.

BACKGROUND: Scientific, accurate, and rapid detection of the composition and content of tea polyphenols is an important basis for their rational use and giving full play to their physiological effect. The spectrophotometric assays for total polyphenols have poor selectivity. Therefore, there is a need to develop a simple and reliable method for the determination of the total polyphenolic level in tea products. OBJECTIVE: The aim of this research was to develop a flow injection chemiluminescence (FI-CL) method based on the Ag(III)-luminol system for the total polyphenol content analysis of tea and substitute tea. METHOD: Through Box-Behnken experimental design, we selected the optimum determination condition. The Ag(III) concentration was 5 × 10-5 mol/L, and the luminol concentration was 3 × 10-7 mol/L (including 0.15 mol/L NaOH). The peristaltic pump is 25 r/min, and the photomultiplier voltage is 600 v. Sample extracts were diluted 100 000 times for the FI-CL assay. RESULTS: Under optimal conditions, CL intensities were proportional to total polyphenol content (in terms of gallic acid concentrations) in the range of 0.1∼100 µg/L. The LOD and LOQ were 0.03 µg/L and 0.1 µg/L. The recovery values were in the range of 86.3-111.0% with a RSD of 1.04∼2.62%. The polyphenolic content of 12 teas and 6 substitute teas was determined, and the results of the developed method and Folin-Ciocalteu method were highly correlated (r = 0.9493 for tea and r = 0.8533 for substitute tea). CONCLUSIONS: The proposed method is better than the Folin-Ciocalteu method in terms of selectivity, sensitivity, and accuracy. It is suitable for the determination of polyphenol content not only in tea, but also in substitute tea. HIGHLIGHTS: We developed a new flow-injection analysis method for polyphenolic content determination based on the Ag(III)-luminol chemiluminescence system. It is simple, rapid, sensitive, and accurate. It is suitable for the determination of polyphenols content not only in tea, but also in substitute tea.

Electrochemical flow injection analysis for the rapid determination of reducing sugars in potatoes.

Non-enzymatic electrochemical sensors for the monitoring of reducing sugars in foods has great potential as a rapid in-situ detection method. This development involved the assembly of a nanoporous platinum structure on a screen-printed carbon electrode (SPCE). The modified electrode was then employed as an amperometric sensing element in a flow injection analysis (FIA) manifold. The system was successfully applied to the rapid detection of reducing sugars in potatoes, without the need for sample preparation. Optimal signals were achieved in phosphate buffer (pH 7.4) at a flow rate of 0.5 mL min-1 and an applied potential of 0.6 V. Experimental results demonstrated the sensor's long-term stability and high selectivity for reducing sugars. This method provides high sample throughput due to a rapid response time of less than five seconds. Reducing sugar values determined were in good agreement with those recorded using a commercially available enzymatic assay kit.

Fully automated method based on on-line molecularly imprinted polymer solid-phase extraction for determination of lovastatin in dietary supplements containing red yeast rice.

A fully automated method for the determination of lovastatin in dietary supplements containing red yeast rice has been developed. It uses a sequential injection analysis system combined with solid-phase extraction applying highly selective molecularly imprinted polymer sorbent. A miniaturized column for on-line extraction was prepared by packing 4.5 mg of the sorbent in a 5.0 × 2.5-mm-i.d. cartridge, which was used in the flow manifold. Sequential injection analysis manifold enabled all steps of lovastatin extraction and continuous spectrophotometric detection at 240 nm. A limit of detection of 60 µg g-1, a limit of quantitation of 200 µg g-1, and a linear calibration range of 200-2000 µg g-1 were achieved. Intra-day and inter-day precision values (RSD) were ≤ 6.7% and ≤ 4.9%, respectively, and method recovery values of spiked red yeast rice extracts at 200, 1000, and 2000 µg g-1 concentration levels were 82.9, 95.2, and 87.7%. Our method was used for determination of lovastatin lactone in four dietary supplements containing red yeast rice as a natural source of lovastatin, also known as monacolin K. The extracted samples were subsequently analyzed by the reference UHPLC-MS/MS method. Statistical comparison of results (F test, t test, α = 0.05) obtained by both methods did not reveal significant difference. A substantial advantage of the new automated approach is high sample throughput thanks to the analysis time of 7.5 min, miniaturization via down-scaling the extraction column, and smaller sample and solvent consumption, as well as reduced generation of waste. Graphical abstract ᅟ.

A simple flow injection spectrophotometric procedure for iron(III) determination using Phyllanthus emblica Linn. as a natural reagent.

The use of natural reagents from plant extracts for chemical analysis is one approach in the development of green analytical chemistry methodology. In this work, a natural reagent extracted from Phyllanthus emblica Linn. has been applied for the determination of iron(III) using a simple flow injection spectrophotometric method. The method was based on the measurement of a dark-purple complex formed by the reaction between iron(III) and the extracted solution in an acetate buffer (pH 5.6) at 570 nm. Under the optimum conditions, a linear calibration graph in the range of 0.50-20.0 mg L-1 iron(III) was obtained with a correlation coefficient (r2) of 0.9996. The limit of detection and limit of quantification were 0.31 and 0.50 mg L-1, respectively. The relative standard deviation was less than 2.50%. The proposed method was successfully applied for quantitative analysis of iron(III) in pharmaceutical preparations and water samples with a sampling rate of 90 samples h-1. The results are in good agreement with those obtained by the official ICP-OES technique at the 95% confidence level. The presented method provides a simple, cost-effective and environmentally friendly approach which is suitable and useful for determining iron(III). Therefore, it can be considered as an alternative analytical technique in green chemistry.

Employing natural reagents from turmeric and lime for acetic acid determination in vinegar sample.

A simple, rapid and environmentally friendly sequential injection analysis system employing natural extract reagents was developed for the determination of acetic acid following an acid-base reaction in the presence of an indicator. Powdered lime and turmeric were utilized as the natural base and indicator, respectively. Mixing lime and turmeric produced an orange to reddish-brown color solution which absorbed the maximum wavelength at 455 nm, with absorbance decreasing with increasing acetic acid concentration. Influential parameters including lime and turmeric concentrations, reagent and sample aspirated volumes, mixing coil length and dispensing flow rate were investigated and optimized. A standard calibration graph was plotted for 0-5.0 mmol/L acetic acid with r2 = 0.9925. Relative standard deviations (RSD) at 2.0 and 4.0 mmol/L acetic acid were less than 3% (n = 7), with limit of detection (LOD) and limit of quantification (LOQ) at 0.12 and 0.24 mmol/L, respectively. The method was successfully applied to assay acetic acid concentration in cooking vinegar samples. Results achieved were not significantly different from those obtained following a batchwise standard AOAC titration method.

A novel automatic flow method with direct-injection photometric detector for determination of dissolved reactive phosphorus in wastewater and freshwater samples.

The novel automatic flow system, direct-injection detector (DID) integrated with multi-pumping flow system (MPFS), dedicated for the photometric determination of orthophosphates in wastewater and freshwater samples is for the first time described. All reagents and the sample were injected simultaneously, in counter-current into the reaction-detection chamber by the system of specially selected for this purpose solenoid micro-pumps. The micro-pumps provided good precision and accuracy of the injected volumes. For the determination of orthophosphates, the molybdenum blue method was employed. The developed method can be used to detect orthophosphate in the range 0.1-12 mg L-1, with the repeatability (RSD) about 2.2% at 4 mg L-1 and a very high injection throughput of 120 injections h-1. It was possible to achieve a very small consumption of reagents (10 µL of ammonium molybdate and 10 µL of ascorbic acid) and sample (20 µL). The volume of generated waste was only 440 µL per analysis. The method has been successfully applied, giving a good accuracy, to determination of orthophosphates in complex matrix samples: treated wastewater, lake water and reference sample of groundwater. The developed system is compact, small in both size and weight, requires 12 V in supply voltage, which are desirable for truly portable equipment used in routine analysis. The simplicity of the system should result in its greater long-time reliability comparing to other flow methods previously described.

Stacked Injections of Biphasic Extractions for Improved Metabolomic Coverage and Sample Throughput.

Omics technologies attempt to provide comprehensive coverage of their target analytes. Comprehensive coverage of metabolites, the aim of nontargeted metabolomics applications, is hindered by the extreme diversity in physiochemical properties of the metabolome. One approach to deal with this challenge is the use of biphasic extractions. These methods generate two largely complementary extracts from a single sample, with an organic lipid-rich fraction and an aqueous fraction containing largely primary and secondary metabolites. To improve metabolite coverage, these two fractions are then independently analyzed resulting in a doubling of the experimental time. In this manuscript, we describe a novel injection approach, stacked injections of a biphasic extraction (SIBE), which enables simultaneous analysis of the two fractions. We demonstrate that SIBE offers nearly 3-fold more total peak area than a monophasic extract without dramatically increasing instrumentation time required for the analysis. The analytical variance is very slightly increased; however, significant improvements in retention time stability are obtained with SIBE vs monophasic injections. Collectively, these data indicate that SIBE is a viable injection approach whenever comprehensive metabolomic coverage is desired.

Simultaneous determination of rutin and ascorbic acid in a sequential injection lab-at-valve system.

A green, simple, accurate and highly sensitive sequential injection lab-at-valve procedure has been developed for the simultaneous determination of ascorbic acid (Asc) and rutin using 18-molybdo-2-phosphate Wells-Dawson heteropoly anion (18-MPA). The method is based on the dependence of the reaction rate between 18-MPA and reducing agents on the solution pH. Only Asc is capable of interacting with 18-MPA at pH 4.7, while at pH 7.4 the reaction with both Asc and rutin proceeds simultaneously. In order to improve the precision and sensitivity of the analysis, to minimize reagent consumption and to remove the Schlieren effect, the manifold for the sequential injection analysis was supplemented with external reaction chamber, and the reaction mixture was segmented. By the reduction of 18-MPA with reducing agents one- and two-electron heteropoly blues are formed. The fraction of one-electron heteropoly blue increases at low concentrations of the reducer. Measurement of the absorbance at a wavelength corresponding to the isobestic point allows strictly linear calibration graphs to be obtained. The calibration curves were linear in the concentration ranges of 0.3-24mgL-1 and 0.2-14mgL-1 with detection limits of 0.13mgL-1 and 0.09mgL-1 for rutin and Asc, respectively. The determination of rutin was possible in the presence of up to a 20-fold molar excess of Asc. The method was applied to the determination of Asc and rutin in ascorutin tablets with acceptable accuracy and precision (1-2%).

A novel flow injection spectrophotometric method using plant extracts as green reagent for the determination of doxycycline.

A novel flow injection spectrophotometric method was developed for the determination of doxycycline in pharmaceutical preparations using iron(III) contained in extracts from plants. The assay was based on the complex formed between doxycycline and iron(III) characterized by an absorption maximum at 435nm. The calibration graphs obtained over the doxycycline concentration range 5-250µgmL-1 gave correlation coefficients of 0.9979, 0.9987 and 0.9987 with the three green reagents prepared from Senna alata (L.) Roxb. (S. alata), Polygonum hydropiper L. (P. hydropiper) or Diplazium esculentum (Retz.) Sw. (D. esculentum), respectively. The relative standard deviations of the repeatability was <2.00%. The percentage recoveries were in the range of 98.27-101.03%. Doxycycline contents obtained by this new method and by the reference methods reported in literature were in agreement at 95% confidence level with the paired t-test. The sample throughput was 36h-1 for each green reagent.

Assessment of metabolism-dependent drug efficacy and toxicity on a multilayer organs-on-a-chip.

Pharmaceutical development is greatly hindered by the poor predictive power of existing in vitro models for drug efficacy and toxicity testing. In this work, we present a new and multilayer organs-on-a-chip device that allows for the assessment of drug metabolism, and its resultant drug efficacy and cytotoxicity in different organ-specific cells simultaneously. Four cell lines representing the liver, tumor (breast cancer and lung cancer), and normal tissue (gastric cells) were cultured in the compartmentalized micro-chambers of the multilayer microdevice. We adopted the prodrug capecitabine (CAP) as a model drug. The intermediate metabolites 5'-deoxy-5-fluorocytidine (DFUR) of CAP that were metabolized from liver and its active metabolite 5-fluorouracil (5-FU) from the targeted cancer cells and normal tissue cells were identified using mass spectrometry. CAP exhibited strong cytoxicity on breast cancer and lung cancer cells, but not in normal gastric cells. Moreover, the drug-induced cytotoxicity on cells varied in various target tissues, suggesting the metabolism-dependent drug efficacy in different tissues as exisits in vivo. This in vitro model can not only allow for characterizing the dynamic metabolism of anti-cancer drugs in different tissues simultaneously, but also facilitate the assessment of drug bioactivity on various target tissues in a simple way, indicating the utility of this organs-on-chip for applications in pharmacodynamics/pharmacokinetics studies, drug efficacy and toxicity testing.

Real-time imaging and quantitative analysis of doxorubicin transport in a perfusable microvessel platform.

Here we report on real-time imaging and quantitative analysis of solute transport in perfusable cylindrical microvessels formed from Madin-Darby canine kidney (MDCK) cells embedded in a collagen matrix. Fluorescence microscopy was used to image the kinetics of doxorubicin transport following injection. To assess the role of efflux pumps on transport, experiments were performed in microvessels formed from MDCK.2, MDCKII-w/t, and MDCKII-MDR1 cells. MDCKII-w/t and MDCKII-MDR1 showed significant doxorubicin accumulation in the cells, characteristic of the pharmacokinetics of doxorubicin. We present a model for doxorubicin transport that takes into account transport across the cell layer. These results demonstrate how real-time imaging of cell microvessels can be used to analyze the mechanisms of transport and distribution following systemic delivery.

A total analytical system featuring a novel solid-liquid extraction chamber for solid sample flow analysis.

In this work, a total flow analysis system based on a novel solid-liquid extraction chamber is presented. This strategy enables all the main experimental procedures for the analysis of a solid sample to be performed automatically: enrichment of the liquid extract, sample treatment, filtration of the liquid extract from the solid sample, directing the extract towards detection, and finally cleansing of the chamber for the following solid sample to be analyzed. The chamber designed to be incorporated in the flow manifold presents two main features: it accommodates stirring bars for enhancing the extraction process, and it presents replaceable solid sample containers (a spare part of the solid-liquid extraction chamber) to easily replace the solid sample and therefore enhance sample analysis throughput. The chamber performance was assessed using two different solid samples, an ion exchanger resin and vegetable samples, focussing on proton and nitrate ion extraction, respectively. The main figures of merit achieved were relative standard deviation (RSD) and relative error values below 7 % for all determinations. The determination rate for vegetable samples was ca. 12 samples h-1. The proposed strategy may be exploited to perform automatically the analysis of solid samples as it embodies a simple automatic strategy of a very important but time-consuming and laborious analytical operation. Graphical abstract TAS for solid liquid extraction and nitrate potentiometric determination of vegetable samples.

Ultrasound-assisted dispersive liquid-liquid microextraction of tetracycline drugs from egg supplements before flow injection analysis coupled to a liquid waveguide capillary cell.

A simple, rapid, and efficient ultrasound-assisted dispersive liquid-liquid microextraction (US-DLLME) method was developed for extraction of tetracycline residues from egg supplement samples, with subsequent determination by flow injection analysis (FIA) coupled to a liquid waveguide capillary cell (LWCC) and a controlled temperature heating bath. Tetracyclines react with diazotized p-sulfanilic acid, in a slightly alkaline medium, to form azo compounds that can be measured at 435 nm. The reaction sensitivity improved substantially (5.12-fold) using an in-line heating temperature of 45 °C. Multivariate methodology was used to optimize the factors affecting the extraction efficiency, considering the volumes of extraction and disperser solvents, sonication time, extraction time, and centrifugation time. Good linearity in the range 30-600 µg L(-1) was obtained for all the tetracyclines, with regression coefficients (r) higher than 0.9974. The limits of detection ranged from 6.4 to 11.1 µg L(-1), and the recoveries were in the range 85.7-96.4 %, with relative standard deviation lower than 9.8 %. Analyte recovery was improved by approximately 6 % when the microextraction was assisted by ultrasound. The results obtained with the proposed US-DLLME-FIA method were confirmed by a reference HPLC method and showed that the egg supplement samples analyzed were suitable for human consumption.

Global analysis of chemical constituents in Shengmai injection using high performance liquid chromatography coupled with tandem mass spectrometry.

This study aimed to develop a specific and reliable method to comprehensively analyze the chemical constituents in Shengmai injection (SMI) using high performance liquid chromatography coupled with tandem mass spectrometry. The qualitative analysis of SMI was achieved on a Kromasil 100-5C18 column, and the results demonstrated that a total of sixty-two compounds in SMI were unambiguously assigned or tentatively identified, and further, twenty-one compounds including fourteen saponins, six lignans and one L-borneol-7-O-[ß-D-apiofuranosyl (1→6)]-ß-D-gluco-pyranoside were quantified by HPLC-MS. Furthermore, L-borneol-7-O-[ß-D-apio-furanosyl (1→6)]-ß-D-glucopyranoside, originated from Radix ophiopogonis, was identified and quantified in SMI for the first time. The method validation results indicated that the methods were simple, specific and reliable. All the investigated compounds showed good linearity (r(2)≥0.9992) with a relatively wide concentration range and acceptable recovery at 90.13-109.09%. Consequently, the developed methods were successfully applied to ten batches of SMI samples analysis. The proposed methods may provide a useful and comprehensive reference for the quality control of SMI, and thus to provide supporting data for the quality control and application of SMI clinically.

Differentiation of Aurantii Fructus Immaturus from Poniciri Trifoliatae Fructus Immaturus using flow-injection mass spectrometric (FIMS) metabolic fingerprinting method combined with chemometrics.

A flow-injection mass spectrometric metabolic fingerprinting method in combination with chemometrics was used to differentiate Aurantii Fructus Immaturus from its counterfeit Poniciri Trifoliatae Fructus Immaturus. Flow-injection mass spectrometric (FIMS) fingerprints of 9 Aurantii Fructus Immaturus samples and 12 Poniciri Trifoliatae Fructus Immaturus samples were acquired and analyzed using principal component analysis (PCA) and soft independent modeling of class analogy (SIMCA). The authentic herbs were differentiated from their counterfeits easily. Eight characteristic components which were responsible for the differences between the samples were tentatively identified. Furthermore, three out of the eight components, naringin, hesperidin, and neohesperidin, were quantified. The results are useful to help identify the authenticity of Aurantii Fructus Immaturus.

Intensification of the electrochemiluminescence of luminol on hollow TiO2 nanoshell-modified indium tin oxide electrodes.

Hollow titania nanoshells (HTNSs), which were synthesized by a SiO2 sacrificial template method, were used to intensify the electrochemiluminescence (ECL) of luminol. The size, shell thickness and crystal phase, factors that are important in determining the efficiency, can be controlled by adjusting the template size, precursor concentration and calcination temperature, respectively. The structure of the HTNSs was characterized by transmission electron microscopy, scanning electron microscopy and X-ray diffraction spectroscopy. After structural optimization, the surface of indium tin oxide (ITO)-coated glass was modified with the HTNSs to act as a working electrode for a flow-injection analytical system. The heterostructure demonstrated an ECL emission intensity 150 times higher than that of the bare ITO. The research also revealed that the ECL of luminol on this modified electrode showed a very sensitive response to hydrogen peroxide with a detection limit of 4.6×10(-10)M. In addition to discussing the intensifying mechanism of luminol ECL by HTNSs, we demonstrate that can be successfully applied to evaluate the gross antioxidant activity of garlic.

Loop flow analysis of dissolved reactive phosphorus in aqueous samples.

The current flow based method for the determination of dissolved reactive phosphorus (DRP) suffers interference from salinity (e.g. index refractive difference) and the incidentally formed bubbles, which can be a problem for optical detection. Here we reported a simple and robust loop flow analysis (LFA) method for accurate measurement of DRP in different aqueous samples. The chemistry is based on the classic phosphomolybdenum blue (PMB) reaction and the PMB formed in a novel cross-shaped flow cell was detected at 700 nm using a miniature spectrophotometer. The effects of reagents on the kinetic formation of PMB were evaluated. The detection limit was 32 nM with an optical pathlength of 1cm and the relative standard deviations for repetitive determinations of 1, 2 and 8 µM phosphate solutions were 1.8% (n=113, without any stoppage during repeating analysis for >7h), 1.0% (n=49) and 0.39% (n=9), respectively. The analysis time was 4 min sample(-1). The effects of salinity and interfering ions (silicate and arsenate) were evaluated and showed no interference under the proposed protocol for DRP analysis. Using the LFA method, different aqueous samples with a salinity range of 0-34 were analyzed and the results showed excellent agreement with the reference method (slope 0.9982±0.0063, R(2)=0.9987, n=34). Recoveries for spiked samples varied from 95.4% to 103.7%. The proposed method showed insignificant interference from salinity, silicate and arsenate, higher reproducibility, easier operation and was free of the bubble problem.

Uranium and thorium sequential separation from norm samples by using a SIA system.

This study presents a sequential radiochemical separation method for uranium and thorium isotopes using a novel Sequential Injection Analysis (SIA) system with an extraction chromatographic resin (UTEVA). After the separation, uranium and thorium isotopes have been quantified by using alpha-particle spectrometry. The developed method has been tested by analyzing an intercomparison sample (phosphogypsum sample) from International Atomic Energy Agency (IAEA) with better recoveries for uranium and thorium than the obtained by using a classical method (93% for uranium using the new methodology and 82% with the classical method, and in the case of thorium the recoveries were 70% for the semi-automated method and 60% for the classical strategy). Afterwards, the method was successfully applied to different Naturally Occurring Radioactive Material (NORM) samples, in particular sludge samples taken from a drinking water treatment plant (DWTP) and also sediment samples taken from an area of influence of the dicalcium phosphate (DCP) factory located close to the Ebro river reservoir in Flix (Catalonia). The obtained results have also been compared with the obtained by the classical method and from that comparison it has been demonstrated that the presented strategy is a good alternative to existing methods offering some advantages as minimization of sample handling, reduction of solvents volume and also an important reduction of the time per analysis.

Development of a QPatch automated electrophysiology assay for identifying KCa3.1 inhibitors and activators.

The intermediate-conductance Ca(2+)-activated K(+) channel KCa3.1 (also known as KCNN4, IK1, or the Gárdos channel) plays an important role in the activation of T and B cells, mast cells, macrophages, and microglia by regulating membrane potential, cellular volume, and calcium signaling. KCa3.1 is further involved in the proliferation of dedifferentiated vascular smooth muscle cells and fibroblast and endothelium-derived hyperpolarization responses in the vascular endothelium. Accordingly, KCa3.1 inhibitors are therapeutically interesting as immunosuppressants and for the treatment of a wide range of fibroproliferative disorders, whereas KCa3.1 activators constitute a potential new class of endothelial function preserving antihypertensives. Here, we report the development of QPatch assays for both KCa3.1 inhibitors and activators. During assay optimization, the Ca(2+) sensitivity of KCa3.1 was studied using varying intracellular Ca(2+) concentrations. A free Ca(2+) concentration of 1 µM was chosen to optimally test inhibitors. To identify activators, which generally act as positive gating modulators, a lower Ca(2+) concentration (∼200 nM) was used. The QPatch results were benchmarked against manual patch-clamp electrophysiology by determining the potency of several commonly used KCa3.1 inhibitors (TRAM-34, NS6180, ChTX) and activators (EBIO, riluzole, SKA-31). Collectively, our results demonstrate that the QPatch provides a comparable but much faster approach to study compound interactions with KCa3.1 channels in a robust and reliable assay.