Comparison of retention of monolithic zirconia crowns with alumina airborne-particle abraded and nonabraded intaglio using three different cements: A clinical simulation.

STATEMENT OF PROBLEM: The necessity of roughening the intaglio surface of zirconia crowns to achieve adequate retention is unclear. PURPOSE: The purpose of this clinical simulation study was to evaluate the retention of airborne-particle-abraded and nonabraded monolithic zirconia crowns using 3 different cement types. MATERIAL AND METHODS: Extracted human molars were used and prepared with a 10-degree taper. Impressions were made of the prepared teeth with a polyvinyl siloxane (PVS) material, and dies were made with Type 4 gypsum. Each die was scanned with a NobelProcera 1G Scanner, and the standard tessellation language (STL) files were transferred electronically to the Nobel Biocare production site, where a bar was added virtually on top of each crown and parameters were set for milling. Seventy-two Procera zirconia crowns were generated, of which half were airborne-particle abraded on the intaglio surface with 50-µm alumina particles at 400 to 500 kPa for 15 seconds. The other 36 received no intaglio treatment other than cleaning. Both groups of 36 crowns were divided into 3 subgroups of 12 specimens. The area of each preparation was calculated using a computer-aided design software program. The specimens were distributed to attain similar mean surface areas among the cementation groups. The crowns were cemented onto the specimen with a controlled force of 196 N. The 3 cements used were self-adhesive, modified resin RelyX Unicem Aplicap, resin-modified glass ionomer RelyX Luting, and a composite resin, Panavia F2.0 with ED Primer A & B. All specimens were thermocycled (5 °C to 55 °C) for 5000 cycles and then removed axially with a universal testing machine (Instron Model 5585H) at a crosshead speed of 0.5 mm/min. The removal force was recorded, and stress of dislodgement was calculated for each crown. A 2-way analysis of variance was used for statistical analyses. The type of failure was analyzed with the chi-squared test of association for independent samples (α=.05 for all tests). RESULTS: The mean dislodging force for crowns with airborne-particle abraded intaglio was 5.4 MPa, which was statistically greater than the mean of 3.2 MPa for nonabraded specimens (P<.001). No significant differences related to the dislodging stresses were detected among the 3 cements (P=.109). The mode of failure was similar whether abraded or not, with 50% of specimens retaining cement in the crown after separation. CONCLUSIONS: Alumina airborne-particle abrasion of the intaglio of zirconia to create surface roughness is beneficial in retaining the crowns, regardless of the cement type. The nonabraded crowns demonstrated significantly lower retentive stress with crown removal. The principal mode of failure was similar whether the zirconia intaglio was airborne-particle abraded or not. The most common mode of failure (>50% of specimens) was at least three-fourths of the cement remaining within the crown.

Herbalism and glass-based materials in dentistry: review of the current state of the art.

Half a million different plant species are occurring worldwide, of which only 1% has been phytochemically considered. Thus, there is great potential for discovering novel bioactive compounds. In dentistry, herbal extracts have been used as antimicrobial agents, analgesics, and intracanal medicaments. Glass-ionomer cement (GIC) and bioactive glass (BAG) are attractive materials in dentistry due to their bioactivity, adhesion, and remineralisation capabilities. Thus, this review summarizes the evidence around the use of phytotherapeutics in dental glass-based materials. This review article covers the structure, properties, and clinical uses of GIC and BAG materials within dentistry, with an emphasis on all the attempts that have been made in the last 20 years to enhance their properties naturally using the wisdom of traditional medicines. An extensive electronic search was performed across four databases to include published articles in the last 20 years and the search was concerned only with the English language publications. Publications that involved the use of plant extracts, and their active compounds for the green synthesis of nanoparticles and the modification of GIC and BAG were included up to May 2023. Plant extracts are a potential and effective candidate for modification of different properties of GIC and BAG, particularly their antimicrobial activities. Moreover, natural plant extracts have shown to be very effective in the green synthesis of metal ion nanoparticles in an ecological, and easy way with the additional advantage of a synergistic effect between metal ions and the phytotherapeutic agents. Medicinal plants are considered an abundant, cheap source of biologically active compounds and many of these phytotherapeutics have been the base for the development of new lead pharmaceuticals. Further research is required to assess the safety and the importance of regulation of phytotherapeutics to expand their use in medicine.

Influence of resin cement on color stability when luting lithium disilicate and zirconia restorations.

AIM: To evaluate the influence of resin cement on the color stability of lithium disilicate and zirconia restorations immersed in coffee after aging. MATERIALS AND METHODS: Eighty maxillary premolars were classified into eight groups (n = 10) based on restorative material type (lithium disilicate or zirconia), resin cement type (G-CEM LinkForce; GC Corporation or Panavia SA Cement Plus Automix; Kuraray Noritake Dental), and preheating temperature (25°C or 54°C). Following tooth preparation, each restoration was bonded to its corresponding substrate. Using a reflectance spectrophotometer, Commission Internationale de l'Éclairage (CIE) tristimulus values were detected and calculated (D65 standard illumination, 10-degree observer angle). All specimens were aged (240,000 load cycles followed by 10,000 thermal cycles), then immersed in coffee (18 h). Following that, the second measurements of the color coordinates were determined. The total color differences were measured, and the data were statistically analyzed (α = 0.05). RESULTS: The temperature had a significant effect on ΔL΄ (P < 0.001), ΔC΄ (P < 0.001), and ΔH΄ (P < 0.001). The lithium disilicate restorations were more color stable than the zirconia restorations. Also, there was a significant difference (P = 0.047) between the LinkForce (2.28 ± 0.48) and Panavia SA (2.15 ± 0.46) cement. The restorations cemented at a temperature of 54°C (1.76 ± 0.11) showed significant color differences (P < 0.001) compared with those cemented at a temperature of 25°C (2.67 ± 0.15). A three-way analysis of variance (ANOVA) test revealed that the interaction between the ceramic material, cement type, and temperature had no statistically significant effect (P = 0.611) on the color stability of the ceramic restorations. CONCLUSIONS: Cement type has a significant effect on the color stability of lithium disilicate and zirconia restorations. Cement at a temperature of up to 54°C enhances the color stability of lithium disilicate and zirconia restorations.

The Effect of Nano-Silica Surface Infiltration on Bond Strength of a Phosphate-Monomer-containing Composite Cement to Zirconia.

PURPOSE: To evaluate the bonding receptiveness of zirconia treated with nano-silica surface infiltration and the bond strength of composite cement after aging. MATERIALS AND METHODS: Zirconia ceramic green bodies (Ceramill zolid, Amann Girbach) with dimensions of 10 x 10 x 4 mm were divided into three groups (n = 4): group C (control: no treatment after sintering), group S (sandblasted: 50-µm alumina airborne particle abrasion after sintering) and group N (nanosintered: infiltrated with nano-silica colloid, sintered, and then etched with hydrofluoric acid). Phase transformations were examined through X-ray diffraction (XRD). Composite resin (Filtek Z250, 3M Oral Care) was bonded to zirconia using the 10-MDP-containing composite cement Panavia F (Kuraray Noritake). The composite-cement/zirconia bond strength was immediately measured using the microtensile bond strength test (µTBS) as well as after three months of artificial aging in water (n = 20 microstick specimens/group). Failure mode patterns were examined using SEM. RESULTS: The specimens of groups C and S, as tested by XRD, exhibited almost full tetragonal phases, while a small extent of tetragonal-monoclinic phase transformation (t→m) was observed for group N. Group N achieved the highest bond strengths (41.5 ± 8.6 MPa), which was significantly higher than that measured for groups C and S (p < 0.05). There was a significant drop in µTBS after 90 days of water storage for groups C and S. SEM revealed a decrease in the percentage of cohesive failure in groups N and S after water storage. CONCLUSIONS: Infiltrating zirconia with nano-silica is a reliable method to establish a strong and stable bond to zirconia. The combination of surface infiltration with nano-silica and application of a phosphate monomer-containing composite cement can significantly improve the composite-cement/zirconia bond strength.

Resin-modified glass ionomer enriched with BIOGLASS: Ion-release, bioactivity and antibacterial effect.

Developing dental materials for the prevention of remineralization or demineralization is important for high-risk caries patients. This study aimed to evaluate the physicochemical and microbiological effects of adding 45S5 bioglass to resin-modified glass ionomer cement (RMGIC). Samples belonged to the following groups: GIC: conventional glass ionomer cement (Vitro Fil), RMGIC: resin-modified GIC (Vitro Fil LC), and RMGIC/45S5: RMGIC with 10% (wt %) of 45S5. Changes in pH and release of fluoride, calcium, and phosphorus ions under acidic (pH 4) and neutral (pH 7) pH conditions were evaluated. Antibacterial activity was verified based on colony-forming units. Material sorption and solubility were analyzed after bacterial exposure. After 28 days, the bioactivity of the materials was evaluated using scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS). Analysis of variance, post hoc Scheffe, and Tukey (α = 0.05) tests were employed for statistical analysis. RMGIC/45S5 showed higher alkalization activity, calcium release at pH 4 and 7, and sorption than GIC and RMGIC (p < .05). Release of phosphorus and fluoride at pH 4 and 7 was higher for GIC than that for RMGIC and RMGIC/45S5 (p < .05). RMGIC/45S5 showed higher values than RMGIC (p < .05). However, antibacterial activity did not differ among the groups. Precipitates of calcium and phosphorus were visualized in RMGIC/45S5 samples via SEM/EDS. These results indicate that the RMGIC/45S5 promotes alkalization and increases the release of calcium, phosphorus, and fluoride ions, resulting in precipitate deposition rich in calcium and phosphorus, thereby being a promising option to improve the bioactivity of RMGIC.

Experimental borosilicate bioactive glasses: Pulp cells cytocompatibility and mechanical characterization.

AIM: To assess in vitro the effect of two novel phase separated borosilicate glasses (PSBS) in the system SiO2 -B2 O3 -K2 O-CaO-Al2 O3 on dental pulp cells; and to compare their bioactivity and mechanical properties to a conventional fluoroaluminosilicate glass ionomer cement namely FUJI IX. METHODOLOGY: The cytocompatibility assessment of the two novel borosilicate glasses, one without alumina (PSBS8) and one containing alumina (PSBS16), was performed on cultured primary human pulp cells. Alamar blue assay was used to assess cell metabolic activity and cell morphology was evaluated by confocal imaging. The bioactivity in Stimulated Body Fluid was also evaluated after 1 and 3 weeks of immersion using SEM-EDX analysis. Vickers microhardness and flexural strength were assessed after incorporating the glass particles into a commercial glass ionomer cement (GIC) liquid containing both polyacrylic and polybasic carboxylic acid. RESULTS: The data revealed that the two borosilicate glasses enhanced cell viability ratios at all-time points in both direct and indirect contact assays. After 3 days of contact, PSBS8 without alumina showed higher viability rate (152%) compared to the PSBS16 containing alumina (145%) and the conventional glass ionomer particles (117%). EDX analysis confirmed an initial Ca/P ratio of 2.1 for 45S5K and 2.08 for PSBS8 without alumina after 3 weeks of immersion. The cement prepared using PSBS8 showed significantly higher Vickers hardness values (p = .001) than that prepared using PSBS16 (46.6 vs. 36.7 MPa). After 24 h of maturation, PSBS8 (without alumina) exhibited a flexural strength of 12.9 MPa compared to a value of 16.4 MPa for the commercial control. PSBS8 without alumina had a higher strength than PSBS16 with alumina, after 1 and 7 days of maturation (p = .001). CONCLUSIONS: The present in vitro results demonstrated that the borosilicate bioactive glass without alumina enhanced pulp cell viability, spreading and acellular bioactivity better than the conventional GIC and the experimental borosilicate glass containing alumina.

Comparison of Dentin Caries Remineralization with Four Bioactive Cements.

The treatment of deep carious lesions involves the use of ion-releasing agents to seal the lesions. These agents release minerals, leading to the remineralization of the remaining demineralized dentin. This study aimed to compare the dentin caries remineralization with bioactive cements. 60 Dentin blocks were prepared from the dentin of human third molars. Artificial carious lesions were induced on the blocks with pH cycling. The samples were divided into five groups (n=12). Dycal, Oxford ActiveCal PC, Biodentine, and ACTIVA BioACTIVE were applied using a mold. One group did not receive any cement. The samples were stored in remineralization solution for 30 days. The cement was removed using a #15 blade, and the dentin surface was evaluated using Energydispersive X-ray Spectroscopy and X-ray Diffraction. One-way ANOVA did not show a significant difference in the weight percentages of calcium and phosphorus and the calcium-to-phosphorus ratios between the groups. The highest and the lowest weight percentages of calcium and phosphorus were observed in Biodentine and control groups, respectively. There were no significant differences in the remineralization properties of bioactive cements. Hydroxyapatite crystals were not formed in any of the adjacent dentin using these cements.

Which Zirconia Surface-cleaning Strategy Improves Adhesion of Resin Composite Cement after Saliva Contamination? A Systematic Review and Meta-Analysis.

PURPOSE: To identify the most effective cleaning method for saliva-contaminated zirconia surface before adhesive cementation through a systematic review and meta-analysis. MATERIALS AND METHODS: PubMed, Scopus, and Web of Science databases were searched to select in vitro studies published through October 2021. Studies that did not perform aging methods, had a sample size less than 5 per group, or did not present a group with zirconia contaminated only with saliva were excluded. Data were extracted and risk of bias was assessed. Statistical analysis comparing the cleaning methods was conducted, and the standardized mean difference was assessed using the R software program. RESULTS: Among 804 potentially eligible studies, 36 were selected for full-text reading, of which 13 were included in qualitative analysis, and 11 of these were subsequently included in the quantitative analysis. A meta-analysis revealed a significant difference in the bond strength between the cleaning methods. Sandblasting with Al2O3  showed a higher bond strength than cleaning solution (Ivoclean, Ivoclar Vivadent) (p < 0.01, I2 = 65%), and both methods promoted higher resin-bond strength to zirconia than water cleaning. In addition, there was no significant difference in the bond strength between alcohol (p = 0.35, I2 = 79%), phosphoric acid (p < 0.23, I2 = 90%), and water cleaning. CONCLUSION: Sandblasting with Al2O3 seems to be the best method for zirconia surface cleaning before adhesive luting, promoting better resin-bond strength to zirconia.

Plant extract incorporated into glass ionomer cement as a photosensitizing agent for antimicrobial photodynamic therapy on Streptococcus mutans.

BACKGROUND: A plant extract (EB) incorporated into glass ionomer cement (GIG) could be a potential photosensitizer for Antimicrobial PDT (aPDT) against caries-microorganisms, replacing methylene blue (MB), due to the presence of chlorophyll. GIC + EB + aPDT could be an therapeutic alternative to dentin decontamination and sealing, allowing reduction of operative time. OBJECTIVE: Evaluate Dioscorea altissima (EB) incorporated into GIC as a photosensitizer for aPDT against Streptococcus mutans. METHODS: Groups (n = 24; ntotal = 192): G1-GIC; G2-GIC + LASER; G3-GIC/EB; G4-GIC/EB + LASER; G5-GIC+MB; G6-GIC + aPDT; G7-GIC/EB + MB; and G8 - GIC/EB+aPDT. In aPDT groups, MB was the photosensitizer. In LASER groups, MB was not used. The irradiation protocol was 660 nm/100 mW/5 J/150 J/cm²/50 s, with a 5-min pre-irradiation time for the MB groups. Antibacterial assays were carried out in 24-well microplates. The wells were completed with one milliliter of a S. mutans in BHI at 1.3 × 108 CFU/mL suspension. After incubation, PDT or laser was performed. After MTT bacteria viability test, the data were submitted to the Kolgomorov-Smirnoff normality test, followed by one-way ANOVA and Tukey's posterior test, α < 0.05. RESULTS: Group G6 showed significant inhibition (p < 0.001), followed by groups G4, G5, G7, and G8, which did not show significant differences among them (p > 0.05). Groups G2 and G3 also showed similar results (p > 0.05) and were the least active compared to the others. CONCLUSIONS: EB potentiated the antimicrobial action of GIC against S. mutans and laser irradiation over GIC/EB presented better antimicrobials results. The results indicate that EB could be a potential photosensitizer for aPDT.

Antimicrobial Efficacy of Glass Ionomer Cement in Incorporation with Biogenic Zingiber officinale Capped Silver-Nanobiotic, Chlorhexidine Diacetate and Lyophilized Miswak.

In the present study, Zingiber officinale is used for the synthesis of Zingiber officinale capped silver nanoparticles (ZOE-AgNPs) and compares the antimicrobial efficacy and compressive strength of conventional glass ionomer cement (GIC) combined with ZOE-AgNPs, lyophilized miswak, and chlorhexidine diacetate (CHX) against oral microbes. Five groups of the disc-shaped GIC specimens were prepared. Group A: lyophilized miswak and GIC combination, Group B: ZOE-AgNPs and GIC combinations, Group C: CHX and GIC combination, Group D: ZOE-AgNPs + CHX + GIC; Group E: Conventional GIC. Results confirmed the successful formation of ZOE-AgNPs that was monitored by UV-Vis sharp absorption spectra at 415 nm. The X-ray diffractometer (XRD) and transmission electron microscope (TEM) results revealed the formation of ZOE-AgNPs with a mean size 10.5-14.12 nm. The peaks of the Fourier transform infrared spectroscopy (FTIR) were appearing the involvement of ZOE components onto the surface of ZOE-AgNPs which played as bioreducing, and stabilizing agents. At a 24-h, one-week and three-week intervals, Group D showed the significantly highest mean inhibitory zones compared to Group A, Group B, and Group C. At microbe-level comparison, Streptococcus mutans and Staphylococcus aureus were inhibited significantly by all the specimens tested except group E when compared to Candida albicans. Group D specimens showed slightly higher (45.8 ± 5.4) mean compressive strength in comparison with other groups. The combination of GIC with ZOE-AgNPs and chlorhexidine together enhanced its antimicrobial efficacy and compressive strength compared to GIC with ZOE-AgNPs or lyophilized miswak or chlorhexidine combination alone. The present study revealed that The combination of GIC with active components of ZOE-AgNPs and chlorhexidine paves the way to lead its effective nano-dental materials applications.

Radicular canal disinfection by photosensitizers activated by photodynamic therapy and Er, Cr: YSGG laser bonded to glass fiber post using different cement types. An Invitro study.

AIM: To assess the tensile bond strength (TBS) of conventional glass ionomer cement (GIC) and resin cemented fiber post to radicular dentin when disinfected with different photosensitizers methylene blue photosensitizer (MBP), curcumin photosensitizer (CP), and laser therapy Er, Cr: YSGG laser (ECYL) MATERIAL AND METHODS: Sixty carefully extracted, non-traumatic, non-carious, closed apex human mandibular premolars were collected. Periodontal fibers, plaque, or calculi were detached. Decoration of samples was executed up till the cementoenamel junction. Samples were embedded perpendicularly in a heat cure acrylic resin. Canals of all specimens were shaped and cleaned with Protaper universal NiTi system dehydrated with paper points and obturated with gutta-percha. Post space was prepared after the removal of gutta-percha via peso reamers. Post space was disinfected with MBPv100mg/L in group 1; group 2 500 mg/L and group 3 ECL. After sequential photo-irradiation therapies, fiber post was luted with resinous cement and GIC (n = 10 each). After post-cementation, all specimens were subjected to tensile strength in the universal testing machine in Newton. Failure analysis was assessed at 30x magnification.TBS determination was statistically analyzed by one-way variance analysis (ANOVA), followed by the Tukey test (p= 0.05) by parallelizing different groups. RESULTS: Fiber post cemented to radicular dentin with Rely X ARC resin cement and radicular canal disinfected with CP offered the highest TBS (289.25±3.27 N). Similarly, canal space disinfected with MBP and post-luted via Rely X ARC showed the lowest TBS (281.54±4.46 N). Intragroup comparison unveiled that there is no statistical difference between tensile strength sustained by two luting cement (p>0.05). CONCLUSION: Rely X ARC resinous cement bared the highest tensile bond strength for a post-dentine-cement bond with different photo-activated canal disinfectants (Methylene blue photosensitizer, Curcumin photosensitizer) and Er, Cr: YSGG then Vidrion C (GIC).

Comparison of 3- and 90-day bond strengths of 3 types of cement to nickel-chromium alloy.

The purpose of this in vitro study was to compare the 3- and 90-day bond strengths of 3 cements used for luting metal-ceramic crowns. Zinc phosphate cement (ZPC; SS White), resin-modified glass ionomer cement (RMGIC; Fuji Plus), and self-adhesive resin cement (SARC; RelyX U200) were assessed in 2 different treatment conditions (with and without microsandblasting of the alloy) and at 2 experimental times (3 days [E1] and 90 days [E2] after cementation). The buccal surfaces of 84 bovine teeth were ground until the dentin was exposed, and 84 nickel-chromium alloy plates cast from a resin model were cemented to the dentin surfaces with 1 of the 3 cements (n = 28). In half of the specimens of each group (n = 14), the bonding surfaces of the nickel-chromium plates received 6 seconds of microsandblasting with 45-µm aluminum oxide particles prior to cementation. The compressive shear bond strengths of the specimens were evaluated in a universal testing machine at E1 and E2 (n = 7). The SARC group showed the greatest bond strength, followed by the RMGIC group, while the bond strength of the ZPC group was significantly lower (P < 0.01). For the RMGIC specimens subjected to microsandblasting, there was a statistically significant difference between the mean bond strengths at E1 and E2 (P = 0.040). All of the other cement and treatment groups showed statistically similar adhesion results at E1 and E2 (P > 0.05). The complementary test by Sidák revealed that the cements Fuji Plus and RelyX U200 showed higher values at E2 and were statistically similar to each other (P > 0.05). Although RMGIC specimens showed a lower initial bond strength than SARC specimens, the fact that the microsandblasted RMGIC subgroup was the only one that demonstrated a significant increase in bond strength with aging suggests that RMGIC can be a material of first choice because it also costs less than SARC.

Caries effected dentin disinfection using Ozone, methylthioninium chloride and turmeric activated by photodynamic therapy on bond integrity of resin-modified glass ionomer cement.

AIM: To evaluate the shear bond strength (SBS) of caries effected dentin (CAD) bonded to resin-modified glass ionomer cement (RMGIC) after being disinfected with different methods their effect on microleakage scores. MATERIAL AND METHODS: Based on criteria of ICDAS seventy-five teeth were selected and disinfected. All samples were grounded and a cavity prepared followed by random allocation of samples into different disinfection groups i.e., methylene blue photosensitizer (MBP), Silver diamine fluoride (SDF), Ozone (O3); curcumin photosensitizer (CP) and chlorhexidine (CHX) (n = 15). All samples were restored with resin modified glass ionomer (RMGIC) incrementally. Ten specimens from each group were placed in universal testing machine (UTM) to calculate bond failure and failure type. Five samples from each group were evaluated for microleakage scores. SBS and microleakage scores was examined using analysis of variance (ANOVA) with a Post-hoc test. For all tests p-value, less than 0.5 was considered statistically significant. RESULTS: The highest SBS was observed in CAD disinfected with CP bonded to RMGIC (16.42 ± 1.10 MPa). Similarly, the lowest bond values were demonstrated by CAD disinfected with MBP (9.21 ± 0.22 MPa) bonded to RMGIC respectively. CAD disinfected with CHX (Control) bonded to RMGIC demonstrated the lowest microleakage scores and showed a significant difference compared to other experimental groups (p< 0.05). CONCLUSION: Curcumin along with O3 has the potential to be used as a disinfectant in CAD as it improves SBS to RMGIC. CHX demonstrates low microleakage scores with decrease of bond integrity.

Using Proanthocyanidin as a Root Dentin Conditioner for GIC Restorations.

Glass ionomer cements (GICs) are considered the material of choice for restoration of root carious lesions (RCLs). When bonding to demineralized dentin, the collapse of dentinal collagen during restorative treatment may pose challenges. Considering its acidic nature and collagen biomodification effects, proanthocyanidin (PAC) could be potentially used as a dentin conditioner to remove the smear layer while simultaneously acting to biomodify the dentinal collagen involved in the bonding interface. In this study, 6.5% w/v PAC was used as a conditioner for sound (SD) and laboratory demineralized (DD) root dentin before bonding to resin-modified GIC (FII), casein phosphopeptide-amorphous calcium phosphate (CPP-ACP)-modified GIC (FVII), or a high-viscosity GIC (FIX). Root dentin conditioned with deionized distilled water (DDW) or polyacrylic acid (PAA) served as controls. Results indicated FII showed higher shear bond strength (SBS) on SD than the other 2 GICs, especially in PAA-conditioned samples; FIX showed significantly higher SBS than FII and FVII on PAA- or PAC-conditioned DD. In each category of GIC, PAA and PAC did not have a significant influence on SBS in most cases compared to DDW except for a significant decrease in PAC-conditioned SD bonded to FII and a significant increase in PAA-conditioned DD bonded to FIX. The bonding interface between GIC and SD was generally more resistant to the acid-base challenge than DD. Although the alterations in failure modes indicated a compromised interfacial interaction between GICs and PAC-treated root dentin, biomodification effects of PAC on dentin were observed from Raman microspectroscopy analysis in terms of the changes in mineral-to-matrix ratio and hydroxyproline-to-proline ratio of dentin adjacent to the bonding interface, especially of DD. Results from this study also indicated the possibility of using in situ characterization such as Raman microspectroscopy as a complementary approach to SBS test to investigate the integrity of the bonding interface.

Effect of the incorporation of hydroxyapatite on the diametral tensile strength of conventional and hybrid glass ionomer cements.

The objective was to evaluate the effect of the incorporation of calcium hydroxyapatite particles (HAp) in the diametral tensile strength of a conventional type II glass ionomer (GC Gold Label 2) and a resin-modified glass ionomer cement (GC Gold Label 2 LC R). Two experimental HAp (E1HAp or E2HAp) were synthesized and characterized using X-ray diffraction and Confocal Raman spectroscopy. Both HAp were added into the powder of a conventional or resin-modified glass ionomer cement at 5 or 10 wt.%. A commercial HAp (CHAp) was used as reference material. For each glass ionomer cement, a group without the incorporation of HAp was used as a control. A universal testing machine was used for the mechanical test. The results were analyzed through a two-way ANOVA test followed by a complementary Tukey test. For all analyzes, the level of significance was set at α = 0.05. The average particle size for E1Hap was 15 µm, E2HAp was 35 µm and for CHAp was 1 µm. For conventional GIC, the addition of 10% E1HAp and 5% CHAp significantly increased the diametral tensile strength values (p ≤ 0.005). On the other hand, for the resin-modified GIC, except for the 5% E2HAp group, all experimental groups significantly reduced the values of diametral tensile strength (p ≤ 0.007). The addition of HAp improved the mechanical properties only for the conventional glass ionomer cement.

Evaluación clínica de acondicionamiento dentinario y presentaciones de ionómeros fotoactivados en odontopediatría / Clinical evaluation of dentin conditioning and different presentations of light cured glass ionomer in primary dentition

Objetivo: Comparar clínicamente el comportamiento, el tiempo operatorio requerido, el costo y la dificultad de diferentes técnicas de restauración en piezas primarias, empleando ionómero vítreo fotoactivado (IVF) polvo/líquido, con y sin uso de acondicionamiento dentinario, y en cápsulas, con acondicionamiento. Materiales y métodos: El diseño de este estudio fue experimental y comparativo. Se realizaron, en 18 pacientes de 7±2 años, 33 restauraciones con IVF de una o más piezas primarias vitales con lesiones amelodentinarias en 1 o 2 superficies. Según su día de concurrencia a la Cátedra de Odontología Integral Niños, se empleó: A) IVF polvo/líquido, con acondicionamiento (3M™ VitremerTM); B) IVF polvo/líquido, sin acondicionamiento (3M™ VitremerTM); y C) IVF en cápsulas, con acondicionamiento (Riva Light Cure). Las restauraciones fueron evaluadas clínicamente al inicio y a los 12 meses según los siguientes criterios: pérdida total, pérdida total con caries, requerimiento de reemplazo por pérdida parcial, requerimiento de reemplazo por caries, aceptable con deterioro, en condiciones. El grado de dificultad se analizó utilizando una planilla diseñada para tal fin. El tiempo operatorio requerido se midió sin considerar el tiempo de inserción. Resultados: El tiempo operatorio requerido fue de 2 minutos, 15 segundos en A; 1 minuto, 25 segundos en B; y 1 minuto, 10 segundos en C, sin considerar el tiempo de inserción. El costo fue 61,11% mayor para C. La dificultad fue de 3,2±0,6 para A y B, y de 1,5±0,7 para C (ANOVA; P<0,001). El comportamiento clínico no registró diferencias significativas entre los grupos (Fisher; P=0,339). Conclusión: Los ionómeros de restauración fotoactivados encapsulados utilizados en este estudio presentaron menor dificultad de manipulación, mayor costo y similar comportamiento clínico a un año que las presentaciones polvo-líquido, con o sin uso de acondicionamiento previo en piezas primarias (AU)

Aim: To assess the clinical performance, operative time required, cost and technical difficulties of different restorative techniques in primary teeth, using light cured glass ionomers (LCG), powder/liquid, with and without dentin conditioning and light cured glass ionomer in capsules with conditioning. Materials and methods: The design of this study was experimental and comparative. 33 restorations with LCG were performed in 18 patients, 7 ± 2-years-old, in one or more vital primary teeth with carious lesions involving one or more tooth surfaces. Patients were assigned to one of the three groups according to the day of the week in which they attended to the Pediatric Department of the Dental School: A) LCG powder/liquid, with conditioning (3M™ VitremerTM); B) LCG powder/liquid without conditioning (3M™ VitremerTM); and C) LCG in capsules with conditioning (Riva Light Cure). The restorations were clinically evaluated at baseline and after 12 months according to the following criteria: complete loss of the restoration, complete loss with caries, need of replacement because of partial loss, need of replacement because of caries, good condition with some wear and good condition. Technical difficulties were analyzed using a data sheet designed for that purpose. The operative time required was evaluated without considering the insertion time. Results: Time operative time required was 2 minutes 15 seconds in A, 1 minute 25 seconds in B and 1 minute 10 seconds in C. Cost was 61.11% higher for C. Difficulty was 3.2±0.6 for A and B and 1.5±0.7 for C (ANOVA; P<0.001). No significant differences were observed among the three groups in relation to the clinical performance (Fisher; P=0.339). Conclusions: In these 12 months, study in primary teeth, the light cured glass ionomers used dispensed in capsules showed to be the easiest to handle, had higher cost and similar clinical performance than the powder liquid presentations with and without dentin conditioner (AU)

Kinetics of ion release from a conventional glass-ionomer cement.

Release kinetics for sodium, silicon, aluminium, calcium and phosphorus from conventional glass-ionomer dental cement has been studied in neutral and acid conditions. Specimens (6 mm height × 4 mm diameter) were made from AquaCem (Dentsply, Konstanz, Germany), 6 per experiment. They were matured (37 °C, 1 h), then placed in 5 cm3 storage solution at 20-22 °C. In the first experiment, deionised water, changed daily for 28 days, was used. In the second, deionised water, changed monthly for 21 months, was used. In the third, lactic acid (20 mmol dm-3, pH: 2.7 ± 0.1), changed monthly for 21 months was used. After storage each solution was analyzed by inductively coupled plasma-optical emission spectroscopy (ICP-OES). Results showed that in neutral conditions, no calcium was released, but in acid, significant amounts were released. The other elements (Na, Al, Si and P) were released in neutral as well as acid conditions, with greater amounts in acid. More frequent changes of water gave greater release. In neutral conditions, release over 21 months followed the equation: [E]c = [E]1t/(t + t½) + ß√t ([E]c is the cumulative release of the element). In acid conditions, this became: [E]c = [E]1t/(t + t½) + αt. Hence release of all elements was shown to occur in two steps, a rapid initial one (half-life: 12-18 h) and a longer second one. In neutral conditions, the longer step involves diffusion; in acid it involves erosion. These patterns influence the material's bioactivity.

Shear Bond Strength and Film Thickness of a Naturally Antimicrobial Modified Dental Luting Cement.

Although several natural plants and mixtures have been known and used over the centuries for their antibacterial activity, few have been thoroughly explored in the field of dentistry. Thus, the aim of this study was to enhance the antimicrobial activity of a conventional glass ionomer cement (GIC) with natural plant extracts. The effect of this alteration on the bond strength and film thickness of glass ionomer cement was evaluated and related to an 0.5% chlorohexidine modified GIC. Olive leaves (Olea europaea), Fig tree (Ficus carica), and the leaves and roots of Miswak (Salvadora persica) were used to prepare an alcoholic extract mixture. The prepared extract mixture after the evaporation of the solvent was used to modify a freeze-dried glass ionomer cement at three different extracts: water mass ratios 1:2, 1:1, and 2:1. An 0.5% chlorhexidine diacetate powder was added to a conventional GIC for the preparation of a positive control group (CHX-GIC) for comparison. The bond strength to dentine was assessed using a material-testing machine at a cross head speed of 0.5 mm/min. Failure mode was analyzed using a stereomicroscope at 12× magnification. The cement film thickness was evaluated in accordance with ISO standard 9917-1. The minimum number of samples in each group was n = 10. Statistical analysis was performed using a Kruskal-Wallis test followed by Dunn's post hoc test for pairwise comparison. There was a statistically insignificant difference between the median shear bond strength (p = 0.046) of the control group (M = 3.4 MPa), and each of the CHX-GIC (M = 1.7 MPa), and the three plant modified groups of 1:2, 1:1, 2:1 (M = 5.1, 3.2, and 4.3 MPa, respectively). The CHX-GIC group showed statistically significant lower median values compared to the three plant-modified groups. Mixed and cohesive failure modes were predominant among all the tested groups. All the tested groups (p < 0.001) met the ISO standard of having less than 25 µm film thickness, with the 2:1 group (M = 24 µm) being statistically the highest among all the other groups. The plant extracts did not alter either the shear bond strength or the film thickness of the GIC and thus might represent a promising additive to GICs.

Antimicrobial activity of biosynthesized silver nanoparticles, amoxicillin, and glass-ionomer cement againstStreptococcus mutansandStaphylococcus aureus.

Background. The development of dental caries is associated with various microorganisms and secondary caries formation is the main cause of restorations failure. The advice for restorative dental materials that have antimicrobial properties has stimulated the introduction of materials containing different antibacterial agents.Objectives. The present study has been designed to synthesize silver nanoparticles (AgNPs) and incorporate AgNPs and amoxicillin into glass ionomer cement (GIC) to synergize its effect on oral microbes. The effect of the added antimicrobial agents on compressive strength (CS) of GIC was also evaluated.Material and methods. Biosynthesis of AgNPs was done usingCupressus macrocarpaextract and AgNPs were characterized. A total of 120 disc-shaped specimens were prepared and classified into 4 main groups where Group A includes conventional GIC, Groups B and C include GIC with AgNPs or amoxicillin, respectively, while Group D included GIC with both AgNPs and amoxicillin. Each group was tested for the antimicrobial activity against bothStreptococcus mutans(S. mutans) andStaphylococcus aureus(S. aureus). The distribution of biofilm was examined via a scanning electron microscope. The CS of the tested material was measured using a Material Test System.Results. The UV-visible spectrum showed a peak of 429 nm. Transmission electron microscopy, x-ray diffraction pattern and Fourier transform infrared analysis confirmed the formation of AgNPs with spherical to oblong polydispersed particles of diameter in the range of 13.5-25.8 nm. The maximum inhibitory zone was recorded for group D against both tested bacteria with a mean of 29 mm at first 24 h period to 15 mm at three weeks and showed antimicrobial rate 92.2% and 92.56%, against both strains, respectively. Additionally, group D disintegrated the structure ofS. aureusbiofilm and even kill bacteria in the biofilms. The addition of AgNPs and amoxicillin caused an insignificant effect on CS of GIC.Conclusion.TheAgNPs showed a synergistic effect in combination with amoxicillin and GIC dental restorative material against studied microorganisms. The agents can be safely added with minimal effect on the mechanical properties of the original cement.

Preparation of glass-ionomer cement containing ethanolic Brazilian pepper extract (Schinus terebinthifolius Raddi) fruits: chemical and biological assays.

Plants may contain beneficial or potentially dangerous substances to humans. This study aimed to prepare and evaluate a new drug delivery system based on a glass-ionomer-Brazilian pepper extract composite, to check for its activity against pathogenic microorganisms of the oral cavity, along with its in vitro biocompatibility. The ethanolic Brazilian pepper extract (BPE), the glass-ionomer cement (GIC) and the composite GIC-BPE were characterized by scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), and thermal analysis. The BPE compounds were identified by UPLC-QTOF-MS/MS. The release profile of flavonoids and the mechanical properties of the GIC-BPE composite were assessed. The flavonoids were released through a linear mechanism governing the diffusion for the first 48 h, as evidenced by the Mt/M∞ relatively to [Formula: see text], at a diffusion coefficient of 1.406 × 10-6 cm2 s-1. The ATR-FTIR analysis indicated that a chemical bond between the GIC and BPE components may have occurred, but the compressive strength of GIC-BPE does not differ significantly from that of this glass-ionomer. The GIC-BPE sample revealed an ample bacterial activity at non-cytotoxic concentrations for the human fibroblast MRC-5 cells. These results suggest that the prepared composite may represent an alternative agent for endodontic treatment.