Electrospun lignin-PVP nanofibers and their ability for structuring oil.

This work explores the electrospinnability of low-sulfonate Kraft lignin (LSL)/polyvinylpyrrolidone (PVP) solutions in N,N-dimethylformamide (DMF) and the ability of the different micro- and nano-architectures generated to structure castor oil. LSL/PVP solutions were prepared at different concentrations (8-15 wt%) and LSL:PVP ratios (90:10-0:100) and physico-chemically and rheologically characterized. The morphology of electrospun nanostructures mainly depends on the rheological properties of the solution. Electrosprayed nanoparticles or micro-sized particles connected by thin filaments were obtained from solutions with low LSL/PVP concentrations and/or high LSL:PVP ratios, whereas beaded or bead-free nanofibers were produced by increasing concentration and/or decreasing LSL:PVP ratio, due to enhanced extensional viscoelastic properties and non-Newtonian characteristics. Electrospun LSL/PVP nanofibers are able to form oleogels by simply dispersing them into castor oil at concentrations between 10 and 30 wt%. The rheological properties of the oleogels may be tailored by modifying the LSL:PVP ratio and nanofibers content. The potential application of these oleogels as bio-based lubricants was also explored in a tribological cell. Satisfactory friction and wear results are achieved when using oleogels structured by nanofibers mats with enhanced gel-like properties as lubricants. Overall, electrospinning of lignin/PVP solutions can be proposed as a simple and effective method to produce nanofibers for oil structuring.

Improved preparation of vitexin from hot water extract of Basella alba, the commercially available vegetable Malabar spinach ("Tsurumurasaki" in Japanese) and the application to semisynthesis of chafuroside B.

Hot water extraction of D-arabinofuranosylvitexin from the raw leaves of commercially available Basella alba "Tsurumurasaki" and subsequent acidic hydrolysis was improved to be a procedure using a high-pressure steam sterilizer to afford vitexin. The amount was estimated to be 14.1 mg from 1 g of dry weight of the raw leaves, whose recovery was calculated to be 95% based on the estimated content of D-arabinofuranosylvitexin in B. alba raw leaves. The product was dehydratively cyclized between hydroxy groups on the carbohydrate and flavone skeletons under modified Mitsunobu reaction conditions in N,N-dimethylformamide to give chafuroside B, which is known to be a bioactive Oolong tea polyphenol. Through these transformations, 10.2 mg of chafuroside B could be semisynthesized from 1 g of dry weight of the raw leaves, and the efficiency was improved compared to that from the extraction from Oolong tea (3.4 µg from 1 g of dry weight).

Efficient removal of toxic phosphate anions from aqueous environment using pectin based quaternary amino anion exchanger.

Pectin based quaternary amino anion exchanger (Pc-QAE) was prepared using simple crosslinking polymerization method. This anion exchanger was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). Pc-QAE was applied for the removal of phosphate anion from the aqueous solution. The adsorption process which was pH dependent showed maximum adsorption of phosphate anions at pH 7. Pc-QAE showed good monolayer adsorption capacity for phosphate anions which demonstrated its good capability towards Langmuir isotherm model. Moreover, the adsorption was evaluated thermodynamically and the negative value of Gibbs free energy (-1.791KJ/mol) revealed the spontaneity of adsorption process. The value of ΔH° and ΔS° were found to be 15.28 and 49.48KJ/mol, respectively representing the endothermic nature and enhancement in degree of freedom due to the adsorption process.

Preparation of ionic liquid-mediated imprinted monolith for selective capture and purification of corilagin.

A method for solid-phase extraction (SPE) of corilagin from natural plant extracts based on molecularly imprinted polymers (MIPs) was developed. For the preparation of corilagin-MIP monoliths, 4-vinylpyridine was used as functional monomer, and ethylene glycol dimethacrylate was used as cross-linking monomer, using a mixture of 1-butyl-3-methylimidazoliumtetrafluoroborate (ionic liquid)-N,N-dimethylformamide-dimethyl sulfoxide as a porogen. A morphological characteristic of the corilagin imprinted monolith was further studied by scanning electron microscopy and nitrogen sorption method. The greatest imprinting factor of COR was up to 9. The MIPs were used as solid-phase extraction (SPE) sorbents for purification of COR and the mean recoveries of corilagin was 78.0% with COR purity of 98.0% from the crude extract of phyllanthus urinaria L. The resulting COR-imprinted polymer also displayed the good performance of fragment imprinting polymer for gallic acid with the mean recoveries of 94.0% and purity of 99.7%.

Predicting changes in aquatic toxicity of chemicals resulting from solvent or dispersant use as vehicle.

The influence of two vehicles (N,N-dimethylformamide [DMF] as solvent and polyoxyethylene hydrogenated castor oil [HCO-40] as a dispersant) on the acute toxicity of eight hydrophobic chemicals with a non-specific mode of action to Daphnia magna was investigated according to the OECD Guidelines for the Testing of Chemicals, No. 202. An increased 48-h EC50 value for D. magna or reduced toxicity resulting from the addition of HCO-40 to the test medium was observed for five of the eight chemicals examined. Each of eight chemicals was dissolved in water at a concentration of either 10 mg/L or 1.0 mg/L, with or without DMF or HCO-40. Silicone film as a model of a biological membrane was then immersed in each solution, and the concentration of each chemical in the water was monitored until equilibrium was reached for each test substance, after which the adsorbed amount of each chemical was determined. The amounts of p-pentylphenol and four other substances with log Pow (1-octanol/water partition coefficient) values greater than 3.4 adsorbed onto the silicone film decreased with increasing concentrations of HCO-40. However, 3-chloro-4-fluoronitrobenzene and two other substances with log Pow values less than 2.6 demonstrated no changes in adsorption with either increasing HCO-40 concentration or the addition of DMF. The reduced adsorption in the presence of a vehicle on the silicone film correlated closely with changes in toxicity. These results indicate that the methodology developed in this study enables the prediction of changes in toxicity resulting from the addition of vehicles to a test system.

Practical Radiosynthesis and Preclinical Neuroimaging of [11C]isradipine, a Calcium Channel Antagonist.

In the interest of developing in vivo positron emission tomography (PET) probes for neuroimaging of calcium channels, we have prepared a carbon-11 isotopologue of a dihydropyridine Ca2+-channel antagonist, isradipine. Desmethyl isradipine (4-(benzo[c][1,2,5]oxadiazol-4-yl)-5-(isopropoxycarbonyl)-2,6-dimethyl-1,4-dihydropyridine -3-carboxylic acid) was reacted with [11C]CH3I in the presence of tetrabutylammonium hydroxide in DMF in an HPLC injector loop to produce the radiotracer in a good yield (6 ± 3% uncorrected radiochemical yield) and high specific activity (143 ± 90 GBq·µmol-1 at end-of-synthesis). PET imaging of normal rats revealed rapid brain uptake at baseline (0.37 ± 0.08% ID/cc (percent of injected dose per cubic centimeter) at peak, 15-60 s), which was followed by fast washout. After pretreatment with isradipine (2 mg·kg-1, i.p.), whole brain radioactivity uptake was diminished by 25%-40%. This preliminary study confirms that [11C]isradipine can be synthesized routinely for research studies and is brain penetrating. Further work on Ca2+-channel radiotracer development is planned.

Transdermal delivery of lercanidipine hydrochloride: effect of chemical enhancers and ultrasound.

The effects of permeation enhancers and sonophoresis on the transdermal permeation of lercanidipine hydrochloride (LRDP) across mouse skin were investigated. Parameters including drug solubility, partition coefficient, drug degradation and drug permeation in skin were determined. Tween-20, dimethyl formamide, propylene glycol, poly ethylene glycol (5% v/v) and different concentration of ethanol were used for permeation enhancement. Low frequency ultrasound was also applied in the presence and absence of permeation enhancers to assess its effect on augmenting the permeation of drug. All the permeation enhancers, except propylene glycol, increased the transdermal permeation of LRDP. Sonophoresis significantly increased the cumulative amount of LRDP permeating through the skin in comparison to passive diffusion. A synergistic effect was noted when sonophoresis was applied in presence of permeation enhancers. The results suggest that the formulation of LRDP with an appropriate penetration enhancer may be useful in the development of a therapeutic system to deliver LRDP across the skin for a prolonged period (i.e., 24 h). The application of ultrasound in association with permeation enhancers could further serve as non-oral and non-invasive drug delivery modality for the immediate therapeutic effect.

Antiplasmodial and leishmanicidal activities of 2-cyano-3-(4-phenylpiperazine-1-carboxamido) quinoxaline 1,4-dioxide derivatives.

Malaria and leishmaniasis are two of the World's most important tropical parasitic diseases. Thirteen new 2-cyano-3-(4-phenylpiperazine-1-carboxamido) quinoxaline 1,4-dioxide derivatives (CPCQs) were synthesized and evaluated for their in vitro antimalarial and antileishmanial activity against erythrocytic forms of Plasmodium falciparum and axenic forms of Leishmania infantum. Their toxicity against VERO cells (normal monkey kidney cells) was also assessed. None of the tested compounds was efficient against Plasmodium, but two of them showed good activity against Leishmania. Toxicity on VERO was correlated with leishmanicidal properties.

Synthesis of 1,2,3-tripnictolide anions by reaction of group 15 Zintl ions with acetylene. Isolation of [E3C2H2](-) (E = P, As) and preliminary reactivity studies.

Dimethylformamide solutions of K(3)E(7) (E = P, As) react with acetylene yielding the 1,2,3-tripnictolide anions [E(3)C(2)H(2)](-) (R = P (1), As (2)). Preliminary studies have shown that 1 and 2 displace labile ligands in [Ru(COD){η(3)-CH(3)C(CH(2))(2)}(2)] (COD = 1,5-cyclooctadiene) to yield the novel complexes [Ru(η(5)-E(3)C(2)H(2)){CH(3)C(CH(2))(2)}(2)}](-) (E = P (3), As (4)).

Optimization of the water-insoluble procedures for USP General Chapter Residual Solvents <467>.

The water-insoluble procedures in US Pharmacopeia (USP) General Chapter Residual Solvents <467>, which are based on European Pharmacopoeia procedures, were optimized and modified before their inclusion in the chapter to improve their scope, performance, and ruggedness. The optimized procedures use a static headspace introduction system with a gas chromatograph equipped with a flame ionization detector. This article describes some of the key changes made to the USP published procedures, including use of dimethyl sulfoxide (DMSO) or dimethylformamide (DMF) as the solvent, addition of 5 mL of water and 1 mL of sample (dissolved in DMSO or DMF) to the headspace vial, use of a 3:1 GC split ratio, and use of new matrix-matched system suitability solutions. These procedures were verified with two different active pharmaceutical ingredients--hydroxyzine pamoate and prednisone. In the investigation, the more polar material (hydroxyzine pamoate) showed greater recoveries for the optimized procedures when prepared in DMSO. The less polar material (prednisone) typically had greater recoveries in DMF for the optimized procedures. During experimentation, insights into sample preparation, additional types of headspace instrumentation, solvent purity, and other parameters were also gained.

NACE-ESI-TOF MS to reveal phenolic compounds from olive oil: introducing enriched olive oil directly inside capillary.

Most CE methods for the analysis of phenols from olive oil use an aqueous electrolyte separation medium, although the importance of NACE is obvious, as this kind of CE seems to be more compatible with the hydrophobic olive oil matrix and could facilitate its direct injection. In the current work we develop a method involving SPE and NACE coupled to ESI-TOF MS. All the CE and ESI-TOF MS parameters were optimized in order to maximize the number of phenolic compounds detected and the sensitivity in their determination. Electrophoretic separation was carried out using a CE buffer system consisting of 25 mM NH(4)OAc/AcH in methanol/ACN (1/1 v/v) at an apparent pH value of 5.0. We studied in depth the effect of the nature and concentration of different electrolytes dissolved in different organic solvents and other experimental and instrumental CE variables. The results were compared with those obtained by CZE (with aqueous buffers) coupled to ESI-TOF MS; both methods offered to the analyst the chance to study phenolic compounds of different families (such as phenolic alcohols, lignans, complex phenols, flavonoids, etc.) from virgin olive oil by injecting methanolic extracts with efficient and fast CE separations. In the case of NACE method, we also studied the direct injection of the investigated matrix introducing a plug of olive oil directly into the capillary.

Simultaneous determination of mercapturic acids derived from ethylene oxide (HEMA), propylene oxide (2-HPMA), acrolein (3-HPMA), acrylamide (AAMA) and N,N-dimethylformamide (AMCC) in human urine using liquid chromatography/tandem mass spectrometry.

Mercapturic acids are highly important and specific biomarkers of exposure to carcinogenic substances in occupational and environmental medicine. We have developed and validated a reliable, specific and very sensitive method for the simultaneous determination of five mercapturic acids derived from several high-production chemicals used in industry, namely ethylene oxide, propylene oxide, acrylamide, acrolein and N,N-dimethylformamide. Analytes are enriched and cleaned up from urinary matrix by offline solid-phase extraction. The mercapturic acids are subsequently separated by means of high-performance liquid chromatography on a Luna C8 (2) column and specifically quantified by tandem mass spectrometric detection using isotopically labelled analytes as internal standards. The limits of detection (LODs) for N-acetyl-S-2-carbamoylethylcysteine (AAMA) and N-acetyl-S-2-hydroxyethylcysteine (HEMA) were 2.5 microg/L and 0.5 microg/L urine, while for N-acetyl-S-3-hydroxypropylcysteine (3-HPMA), N-acetyl-S-2-hydroxypropylcysteine (2-HPMA) and N-acetyl-S-(N-methylcarbamoyl)cysteine (AMCC) it was 5 microg/L. These LODs were sufficient to detect the background exposure of the general population. We applied the method on spot urine samples of 28 subjects of the general population with no known occupational exposure to these substances. Median levels for AAMA, HEMA, 3-HPMA, 2-HPMA and AMCC in non-smokers (n = 14) were 52.6, 2.0, 155, 7.1 and 113.6 microg/L, respectively. In smokers (n = 14), median levels for AAMA, HEMA, 3-HPMA, 2-HPMA and AMCC were 243, 5.3, 1681, 41.7 and 822 microg/L, respectively. Due to the simultaneous quantification of these mercapturic acids, our method is well suited for the screening of workers with multiple chemical exposures as well as the determination of the background excretion of the general population.

Oxidation of suspected N-nitrosodimethylamine (NDMA) precursors by ferrate (VI): kinetics and effect on the NDMA formation potential of natural waters.

The potential of ferrate (Fe(VI)) oxidation to remove N-nitrosodimethylamine (NDMA) precursors during water treatment was assessed. Apparent second-order rate constants (k(app)) for the reactions of NDMA and its suspected precursors (dimethylamine (DMA) and 7 tertiary amines with DMA functional group) with Fe(VI) were determined in the range of pH 6-12. Four model NDMA precursors (dimethyldithiocarbamate, dimethylaminobenzene, 3-(dimethylaminomethyl)indole and 4-dimethylaminoantipyrine) showed high reactivity toward Fe(VI) with k(app) values at pH 7 between 2.6 x 10(2) and 3.2 x 10(5)M(-1)s(-1). The other NDMA precursors (DMA, trimethylamine, dimethylethanolamine, dimethylformamide) and NDMA had k(app) values ranging from 0.55 to 9.1M(-1)s(-1) at pH 7. In the second part of the study, the NDMA formation potentials (NDMA-FP) of the model NDMA precursors and natural waters were measured with and without pre-oxidation by Fe(VI). For most of the NDMA precursors with the exception of DMA, a significant reduction of the NDMA-FP (>95%) was observed after complete transformation of the NDMA precursor. This result was supported by low yields of DMA from the Fe(VI) oxidation of tertiary amine NDMA precursors. Pre-oxidation of several natural waters (rivers Rhine, Neckar and Pfinz) with a high dose of Fe(VI) (0.38 mM = 21 mg L(-1) as Fe) led to removals of the NDMA-FP of 46-84%. This indicates that the NDMA precursors in these waters have a low reactivity toward Fe(VI) because it has been shown that for fast-reacting NDMA precursors Fe(VI) doses of 20 microM (1.1 mg L(-1) as Fe) are sufficient to completely oxidize the precursors.

New antifungal flavone glycoside from Butea monosperma O. Kuntze.

A new bioactive flavone glycoside was isolated from the methanol soluble fraction of the flowers of Butea monosperma O. Kuntze, which was identified as 5,7-dihydroxy-3,6,4'-trimethoxyflavone-7-O-alpha-L-xylopyranosyl-(1-->3)-O-alpha-L-arabinopyranosyl-(1-->4)-O-beta-D-galactopyranoside (1) by several colour reactions, chemical degradations and spectral analysis. The compound 1 shows antimicrobial activity against various fungal species.

A study of vehicles for dosing rodent whole embryo culture with non aqueous soluble compounds.

In rodent whole embryo culture (WEC), finding vehicles for non-aqueous-soluble compounds has been problematic due to developmental toxicity associated with many solvents. The purpose of this study was to identify alternative vehicles for insoluble compounds. In WEC, we evaluated carrier solutions containing bovine serum albumin (BSA) and glycerol as well as the solvents, formamide, dimethylformamide (DMF), dimethyl sulfoxide (DMSO) and ethanol, for relative teratogenicity and delivery of the insoluble teratogen, all-trans retinoic acid (RA). At a concentration of

Simple and rapid catalytic spectrophotometric determination of superoxide anion radical and superoxide dismutase activity in natural medical vegetables using phenol as the substrate for horseradish peroxidase.

The coupling reaction of 4-aminoantipyrine (4-AAP) with phenol using the superoxide anion radical (O2-*) as oxidizing agent under the catalysis of horseradish peroxidase (HRP) was studied. Based on the reaction, O2-* produced by irradiating vitamin B2 (VB2) was spectrophotometrically determined at 510 nm. Under the optimum experimental conditions, the relationship between A510 and O2-* concentration was linear in the range 9.14x10(-6)-1.2x10(-4) mol L(-1). The detection limit was determined to be 1.37x10(-6) mol L(-1). A possible reaction mechanism was discussed. The effect of interferences and surfactants on the determination of O2-* was also investigated. The proposed method was applied to determine superoxide dismutase activity in garlic, scallion, and onion with satisfactory results.