Porous scaffold hydroxyapatite from sand lobster shells (Panulirus homarus) using polyethylene oxide/chitosan as polymeric porogen for bone tissue engineering.

The hydroxyapatite (HAp; Ca10 (PO4 )6 (OH)2 )) has good biocompatibility, bioactivity, and osteoconductivity as a bone implant because the main inorganic mineral of human bone is HAp. The use of scaffold HAp from biogenic resources that contain high calcium and polymer as a pore forming agent to support bone growth is a longstanding area of interest. In this study, porous scaffolds based on HAp were synthesized from sand lobster (SL; Panulirus homarus) shells as a source of calcium using the porogen leaching method with polyethylene oxide (PEO) and chitosan (Chs) as polymeric porogen. The present study aims to synthesize HAp derived from SL shells and evaluate the effect variations of PEO on the physicochemical properties of the scaffold and cytotoxicity in cell viability assay. Briefly, the SL shell powder was calcinated with temperature variations of 600°C, 800°C, and 1000°C for 6 h. Based on the characterization, it was shown that 1000°C was the optimum calcination temperature for SL shells to synthesize HAp using the precipitation method. The characterization results of HAp using energy dispersive x-ray (EDX) revealed that the molar ratio of Ca/P was 1.67. The Fourier transform infrared (FTIR) and x-ray diffractometer (XRD) spectral patterns indicated that HAp had been successfully synthesized with minor ß-tricalcium phosphate (ß-TCP), a calcium phosphate with high biocompatibility. Porous scaffolds were synthesized by varying the concentration of PEO at 0, 5, 10, and 15 wt %. Physicochemical analysis revealed that a higher concentration of PEO affected decreased crystallinity and compressive strength, but on the other hand, the porosity and pore sizes increased. Based on the physicochemical analysis, the synthesized porous scaffold showed that HAp/PEO/Chs 15 wt % had the most potential as a scaffold for biomedical applications. MTT Assay, after 24 h incubation, revealed that the scaffold was safe for use at low concentrations on the MC3T3E1 osteoblast cells, with a percentage of cell viability of 83.23 ± 3.18% at 23.4375 µg/mL. Although the cell viability decreased at higher concentrations, the HAp/PEO/Chs 15 wt % scaffold was cytocompatible with the cells. Thus, in the present study, HAp/PEO/Chs 15 wt % was the best scaffold based on pore structure, chemical composition, mechanical and crystalographic properties and cell viability.

Supercritical CO2-assisted fabrication of CM-PDA/SF/nHA nanofibrous scaffolds for bone regeneration and chemo-photothermal therapy against osteosarcoma.

Concurrent treatment of tumor recurrence and bone defects after surgical resection of osteosarcoma remains a clinical challenge. Combination therapy based on local drug delivery systems shows great promise in the treatment of osteosarcoma. In this study, curcumin modified polydopamine nanoparticle loaded silk fibroin doped with nano-hydroxyapatite (CM-PDA/SF/nHA) nanofibrous scaffolds were developed to induce bone defect regeneration and chemo-photothermal synergistic effects against osteosarcoma. These scaffolds exhibited good photothermal conversion efficiency and photostability. Moreover, the results of ALP staining and alizarin red S (ARS) staining indicated that the CM-PDA/SF/1%nHA scaffolds had the most obvious promotion effect on early osteogenic differentiation. The results of in vitro and in vivo anti-osteosarcoma activity showed that the CM-PDA/SF/1%nHA scaffolds exhibited higher anti-osteosarcoma activity compared to the control and SF scaffolds. In addition, the CM-PDA/SF/1%nHA scaffolds could promote the proliferation and differentiation of bone marrow mesenchymal stem cells in vitro and new bone production in vivo. Thus, these results suggested that the CM-PDA/SF/1%nHA scaffolds could improve bone defect regeneration and achieve chemo-photothermal synergistic effects against osteosarcoma.

Effect of pectin on the crystallization of strontium substituted HA for bone reconstruction application.

The biomacropolymers of bone extracellular matrix (ECM) guide the growth of hydroxyapatite (HA) with various ionic substitutions. Pectin, a plant polysaccharide with chemical similarities to ECM, was investigated for its potential to promote the crystallization of strontium-substituted HA (SH). The influence of pectin (0.5 and 1.0 wt%) on the in situ mineralization of SH (10 and 30 mol% calcium substitution with strontium) was studied. The preferential affinity of pectin to strontium over calcium favoured the incorporation of strontium in apatite, decreased crystal size (18.85-26.22 nm) and retained more pectin residues (8-16%). The residual pectin strongly interacted with small SH particles, resulting in high microhardness (0.43-0.85 GPa) and high surface charge (-32.1 to -30.3 mV), while weak interaction with large HA particles resulted in low microhardness (0.15-0.25 GPa) and low surface charge (-35.4 to -34.6 mV). The in vitro cellular study using human osteoblast-like MG-63 cells demonstrated that inorganic size and material crystallinity play a vital role in regulating osteogenesis. The study suggests that the synchronization of low pectin concentration (0.5 wt%) and high strontium substitution in HA (30 mol%) offers the desired microhardness and in vitro osteogenic properties to emulate natural bone.

Hydroxyapatite nanoparticles promote TLR4 agonist-mediated anti-tumor immunity through synergically enhanced macrophage polarization.

Macrophages represent the most prevalent immune cells in the tumor micro-environment, making them an appealing target for tumor immunotherapy. One of our previous studies showed that hydroxyapatite nanoparticles (HANPs) enhanced Toll-like receptor 4 (TLR4) signal transduction in macrophages. This study was proposed to investigate how HANPs manipulated the phenotype and function of macrophage against 4T1 breast tumors in the presence or absence of MPLA, a low toxic Toll-like receptor 4 (TLR4) agonist. The results demonstrated that the addition of HANPs to MPLA significantly promoted cytokine secretion and macrophage polarization toward a tumoricidal M1 phenotype. Further, the resulting supernatant from HANPs/MPLA co-stimulated macrophages enhanced 4T1 tumor cells apoptosis compared to that from macrophages treated with a single component or PBS control. In particular, we found HANPs elicited immunogenic cell death (ICD) indicated by the increased expression of "danger signals", including HMGB1, CRT and ATP in 4T1 cells. Subsequently, the ICD derivatives-containing supernatant from HANPs-treated 4T1 cells activated macrophage and shifted the phenotype of the cells toward M1 type. Moreover, in a tumor-bearing mice model, HANPs and MPLA synergistically delayed tumor growth compared to PBS control, which was positively associated with the promoted macrophage polarization and ICD induction. Therefore, our findings demonstrated a potential platform to modulate the function of macrophages, and shed a new insight into the mechanism involving the immunomodulatory effect of HANPs for tumor therapy. STATEMENT OF SIGNIFICANCE: Polarizing macrophage toward tumoricidal phenotype by harnessing Toll-like receptor (TLR) agonists has been proven effective for tumor immunotherapy. However, the immunomodulatory potency of TLR agonists is limited due to immune suppression or tolerance associated with TLR activation in immune cells. Herein, we introduced hydroxyapatite nanoparticles (HANPs) to MPLA, a TLR4 agonist. The results demonstrated that the addition of HANPs to MPLA promoted macrophage shift toward tumoricidal M1 phenotype, supported a "hot" tumor transformation, and delayed 4T1 tumor growth. Moreover, we found that HANPs elicited immunogenic cell death that produced "danger" signals from cancer cells thereby further facilitated macrophage polarization. This work is significant to direct the rational design of HANPs coupled with or without TLR agonists for tumor immunotherapy.

Protocol for Cell Colonization and Comprehensive Monitoring of Osteogenic Differentiation in 3D Scaffolds Using Biochemical Assays and Multiphoton Imaging.

The goal of bone tissue engineering is to build artificial bone tissue with properties that closely resemble human bone and thereby support the optimal integration of the constructs (biografts) into the body. The development of tissues in 3D scaffolds includes several complex steps that need to be optimized and monitored. In particular, cell-material interaction during seeding, cell proliferation and cell differentiation within the scaffold pores play a key role. In this work, we seeded two types of 3D-printed scaffolds with pre-osteoblastic MC3T3-E1 cells, proliferated and differentiated the cells, before testing and adapting different assays and imaging methods to monitor these processes. Alpha-TCP/HA (α-TCP with low calcium hydroxyapatite) and baghdadite (Ca3ZrSi2O9) scaffolds were used, which had comparable porosity (~50%) and pore sizes (~300-400 µm). Cell adhesion to both scaffolds showed ~95% seeding efficiency. Cell proliferation tests provided characteristic progression curves over time and increased values for α-TCP/HA. Transmitted light imaging displayed a homogeneous population of scaffold pores and allowed us to track their opening state for the supply of the inner scaffold regions by diffusion. Fluorescence labeling enabled us to image the arrangement and morphology of the cells within the pores. During three weeks of osteogenesis, ALP activity increased sharply in both scaffolds, but was again markedly increased in α-TCP/HA scaffolds. Multiphoton SHG and autofluorescence imaging were used to investigate the distribution, morphology, and arrangement of cells; collagen-I fiber networks; and hydroxyapatite crystals. The collagen-I networks became denser and more structured during osteogenic differentiation and appeared comparable in both scaffolds. However, imaging of the HA crystals showed a different morphology between the two scaffolds and appeared to arrange in the α-TCP/HA scaffolds along collagen-I fibers. ALP activity and SHG imaging indicated a pronounced osteo-inductive effect of baghdadite. This study describes a series of methods, in particular multiphoton imaging and complementary biochemical assays, to validly measure and track the development of bone tissue in 3D scaffolds. The results contribute to the understanding of cell colonization, growth, and differentiation, emphasizing the importance of optimal media supply of the inner scaffold regions.

Calcium-to-phosphorus releasing ratio affects osteoinductivity and osteoconductivity of calcium phosphate bioceramics in bone tissue engineering.

Calcium phosphate (Ca-P) bioceramics, including hydroxyapatite (HA), biphasic calcium phosphate (BCP), and beta-tricalcium phosphate (ß-TCP), have been widely used in bone reconstruction. Many studies have focused on the osteoconductivity or osteoinductivity of Ca-P bioceramics, but the association between osteoconductivity and osteoinductivity is not well understood. In our study, the osteoconductivity of HA, BCP, and ß-TCP was investigated based on the osteoblastic differentiation in vitro and in situ as well as calvarial defect repair in vivo, and osteoinductivity was evaluated by using pluripotent mesenchymal stem cells (MSCs) in vitro and heterotopic ossification in muscles in vivo. Our results showed that the cell viability, alkaline phosphatase activity, and expression of osteogenesis-related genes, including osteocalcin (Ocn), bone sialoprotein (Bsp), alpha-1 type I collagen (Col1a1), and runt-related transcription factor 2 (Runx2), of osteoblasts each ranked as BCP > ß-TCP > HA, but the alkaline phosphatase activity and expression of osteogenic differentiation genes of MSCs each ranked as ß-TCP > BCP > HA. Calvarial defect implantation of Ca-P bioceramics ranked as BCP > ß-TCP ≥ HA, but intramuscular implantation ranked as ß-TCP ≥ BCP > HA in vivo. Further investigation indicated that osteoconductivity and osteoinductivity are affected by the Ca/P ratio surrounding the Ca-P bioceramics. Thus, manipulating the appropriate calcium-to-phosphorus releasing ratio is a critical factor for determining the osteoinductivity of Ca-P bioceramics in bone tissue engineering.

Biological properties of hydroxyapatite coatings on titanium dioxide nanotube surfaces using negative pressure method.

Titanium (Ti) exhibits superior biocompatibility and mechanical properties but is bioinert, while hydroxyapatite (HA) possesses excellent osteogenesis and is widely used for the modification of Ti surface coatings. However, the synthesis of homogeneous and stable HA on metallic materials is still a major challenge. In this study, porous titanium dioxide nanotube arrays were prepared on Ti surface by anodic oxidation, loaded with calcium and phosphorus precursors by negative pressure immersion, and HA coating was formed by in situ crystallization of calcium and phosphorus on the surface by hydrothermal heating. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and bonding strength were conducted to confirm the surface characteristics of each group. The cell proliferation, mineralization degree, and alkaline phosphatase (ALP) activity of MC3T3-E1 cells on samples were calculated and compared in vitro experiments. Cylindrical samples were implanted into rat femurs to evaluate biocompatibility and osteogenesis in vivo. The results showed that HA crystals successfully synthesized in TiO2 nanotubes, enhancing the bonding strength of HA coating and Ti substrate under negative pressure. Moreover, HA coating on Ti substrate remarkably enhanced cell proliferation and osteogenic differentiation activity in vitro, and improved new bone formation as well as osseointegration in vivo.

Black-Phosphorus-Nanosheet-Reinforced Coating of Implants for Sequential Biofilm Ablation and Bone Fracture Healing Acceleration.

Incurable implant-related infection may cause catastrophic consequences due to the existence of a biofilm that resists the infiltration of host immune cells and antibiotics. Innovative approaches inspired by nanomedicine, e.g., engineering innovative multifunctional bionic coating systems on the surface of implants, are becoming increasingly attractive. Herein, 2D black phosphorus nanosheets (BPs) were loaded onto a hydroxyapatite (HA)-coated metal implant to construct a BPs@HA composite coating. With its photothermal conversion effect and in situ biomineralization, the BPs@HA coating shows excellent performances in ablating the bacterial biofilm and accelerating fracture healing, which were verified through both in vitro and in vivo studies. Moreover, differentially expressed genes of bone formation and bone mesenchymal stem cells (BMSCs) regulated by the BPs@HA coating were identified using absolute quantitative transcriptome sequencing followed by the screening of gene differential expressions. A functional enrichment analysis reveals that the expression of core markers related to BMSC differentiation and bone formation could be effectively regulated by BPs through a metabolism-related pathway. This work not only illustrates the great potential in clinical application of the BPs@HA composite coating to eliminate bacteria and accelerate bone fracture healing but also contributes to an understanding of the underlying molecular mechanism of osteogenesis physiological function regulation based on an analysis of absolute quantitative transcriptome sequencing.

Sustained Delivery of Methylsulfonylmethane from Biodegradable Scaffolds Enhances Efficient Bone Regeneration.

Introduction: As a popular dietary supplement containing sulfur compound, methylsulfonylmethane (MSM) has been widely used as an alternative oral medicine to relieve joint pain, reduce inflammation and promote collagen protein synthesis. However, it is rarely used in developing bioactive scaffolds in bone tissue engineering. Methods: Three-dimensional (3D) hydroxyapatite/poly (lactide-co-glycolide) (HA/PLGA) porous scaffolds with different doping levels of MSM were prepared using the phase separation method. MSM loading efficiency, in vitro drug release as well as the biological activity of MSM-loaded scaffolds were investigated by incubating mouse pre-osteoblasts (MC3T3-E1) in the uniform and interconnected porous scaffolds. Results: Sustained release of MSM from the scaffolds was observed, and the total MSM release from 1% and 10% MSM/HA/PLGA scaffolds within 16 days was up to 64.9% and 68.2%, respectively. Cell viability, proliferation, and alkaline phosphatase (ALP) activity were significantly promoted by incorporating 0.1% of MSM in the scaffolds. In vivo bone formation ability was significantly enhanced for 1% MSM/HA/PLGA scaffolds indicated by the repair of rabbit radius defects which might be affected by a stimulated release of MSM by enzyme systems in vivo. Discussion: Finding from this study revealed that the incorporation of MSM would be effective in improving the osteogenesis activity of the HA/PLGA porous scaffolds.

Lithium ion doped carbonated hydroxyapatite compositions: Synthesis, physicochemical characterisation and effect on osteogenic response in vitro.

Hydroxyapatite is a commonly researched biomaterial for bone regeneration applications. To augment performance, hydroxyapatite can be substituted with functional ions to promote repair. Here, co-substituted lithium ion (Li+) and carbonate ion hydroxyapatite compositions were synthesised by an aqueous precipitation method. The co-substitution of Li+ and CO32- is a novel approach that accounts for charge balance, which has been ignored in the synthesis of Li doped calcium phosphates to date. Three compositions were synthesised: Li+-free (Li 0), low Li+ (Li 0.25), and high Li+ (Li 1). Synthesised samples were sintered as microporous discs (70-75 % theoretical sintered density) prior to being ground and fractionated to produce granules and powders, which were then characterised and evaluated in vitro. Physical and chemical characterisation demonstrated that lithium incorporation in Li 0.25 and Li 1 samples approached design levels (0.25 and 1 mol%), containing 0.253 and 0.881 mol% Li+ ions, respectively. The maximum CO32- ion content was observed in the Li 1 sample, with ~8 wt% CO3, with the carbonate ions located on both phosphate and hydroxyl sites in the crystal structure. Measurement of dissolution products following incubation experiments indicated a Li+ burst release profile in DMEM, with incubation of 30 mg/ml sample resulting in a Li+ ion concentration of approximately 140 mM after 24 h. For all compositions evaluated, sintered discs allowed for favourable attachment and proliferation of C2C12 cells, human osteoblast (hOB) cells, and human mesenchymal stem cells (hMSCs). An increase in alkaline phosphatase (ALP) activity with Li+ doping was demonstrated in C2C12 cells and hMSCs seeded onto sintered discs, whilst the inverse was observed in hOB cells. Furthermore, an increase in ALP activity was observed in C2C12 cells and hMSCs in response to dissolution products from Li 1 samples which related to Li+ release. Complementary experiments to further investigate the findings from hOB cells confirmed an osteogenic role of the surface topography of the discs. This research has shown successful synthesis of Li+ doped carbonated hydroxyapatite which demonstrated cytocompatibility and enhanced osteogenesis in vitro, compared to Li+-free controls.

3D printed PCLA scaffold with nano-hydroxyapatite coating doped green tea EGCG promotes bone growth and inhibits multidrug-resistant bacteria colonization.

OBJECTIVES: 3D-printing scaffold with specifically customized and biomimetic structures gained significant recent attention in tissue engineering for the regeneration of damaged bone tissues. However, constructed scaffolds that simultaneously promote bone regeneration and in situ inhibit bacterial proliferation remains a great challenge. This study aimed to design a bone repair scaffold with in situ antibacterial functions. MATERIALS AND METHODS: Herein, a general strategy is developed by using epigallocatechin-3-gallate (EGCG), a major green tea polyphenol, firmly anchored in the nano-hydroxyapatite (HA) and coating the 3D printed polymerization of caprolactone and lactide (PCLA) scaffold. Then, we evaluated the stability, mechanical properties, water absorption, biocompatibility, and in vitro antibacterial and osteocyte inductive ability of the scaffolds. RESULTS: The coated scaffold exhibit excellent activity in simultaneously stimulating osteogenic differentiation and in situ resisting methicillin-resistant Staphylococcus aureus colonization in a bone repair environment without antibiotics. Meanwhile, the prepared 3D scaffold has certain mechanical properties (39.3 ± 3.2 MPa), and the applied coating provides the scaffold with remarkable cell adhesion and osteogenic conductivity. CONCLUSION: This study demonstrates that EGCG self-assembled HA coating on PCLA surface could effectively enhance the scaffold's water absorption, osteogenic induction, and antibacterial properties in situ. It provides a new strategy to construct superior performance 3D printed scaffold to promote bone tissue regeneration and combat postoperative infection in situ.

Grafting biomaterials associated to topical glucocorticoid: effects on pre-osteoblastic cells (MC3T3-E1).

The topical glucocorticoid budesonide has been prescribed before and after sinus lift surgery as adjuvant drug treatment for maxillary sinus membrane inflammation. However, there is no study on the effects of budesonide on the regenerative process of bone grafting biomaterials. We investigated the effect of the association of budesonide with some biomaterials on the growth and differentiation capacity of pre-osteoblastic cells (MC3T3-E1 subclone 4). Xenogeneic (Bio-Oss and Bio-Gen) and synthetic hydroxyapatites (Osteogen, Bonesynth, and HAP-91) were tested in conditioned medium (1% w/v). The conditioned medium was then supplemented with budesonide (0.5% v/v). Cell viability was assessed using the MTT assay (48, 96, and 144 h), and mineralized nodules were quantified after 14 days of culture using the Alizarin Red Staining. Alkaline phosphatase activity was assessed through the release of thymolphthalein at day seven. All biomaterials showed little or no cytotoxicity. The Bio-Gen allowed significantly less growth than the control group regardless of the experimental time. Regarding differentiation potential of MC3T3-E1, the HAP-91-conditioned medium showed remarkable osteoinductive properties. In osteodifferentiation, the addition of budesonide favored the formation of mineral nodules when cells were cultured in medium conditioned with synthetic materials, whereas it weakened the mineralization potential of cells cultured in xenogeneic medium. Regardless of whether budesonide was added or not, Osteogen and Bio-Oss showed higher alkaline phosphatase activity than the other groups. Budesonide may improve bone formation when associated with synthetic biomaterials. Conversely, the presence of this glucocorticoid weakens the mineralization potential of pre-osteoblastic cells cultured with xenogeneic hydroxyapatites.

Electrospun Membrane Surface Modification by Sonocoating with HA and ZnO:Ag Nanoparticles-Characterization and Evaluation of Osteoblasts and Bacterial Cell Behavior In Vitro.

Guided tissue regeneration and guided bone regeneration membranes are some of the most common products used for bone regeneration in periodontal dentistry. The main disadvantage of commercially available membranes is their lack of bone cell stimulation and easy bacterial colonization. The aim of this work was to design and fabricate a new membrane construct composed of electrospun poly (D,L-lactic acid)/poly (lactic-co-glycolic acid) fibers sonocoated with layers of nanoparticles with specific properties, i.e., hydroxyapatite and bimetallic nanocomposite of zinc oxide-silver. Thus, within this study, four different variants of biomaterials were evaluated, namely: poly (D,L-lactic acid)/poly (lactic-co-glycolic acid) biomaterial, poly(D,L-lactic acid)/poly (lactic-co-glycolic acid)/nano hydroxyapatite biomaterial, poly (D,L-lactic acid)/poly (lactic-co-glycolic acid)/nano zinc oxide-silver biomaterial, and poly (D,L-lactic acid)/poly (lactic-co-glycolic acid)/nano hydroxyapatite/nano zinc oxide-silver biomaterial. First, it was demonstrated that the wettability of biomaterials-a prerequisite property important for ensuring desired biological response-was highly increased after the sonocoating process. Moreover, it was indicated that biomaterials composed of poly (D,L-lactic acid)/poly (lactic-co-glycolic acid) with or without a nano hydroxyapatite layer allowed proper osteoblast growth and proliferation, but did not have antibacterial properties. Addition of a nano zinc oxide-silver layer to the biomaterial inhibited growth of bacterial cells around the membrane, but at the same time induced very high cytotoxicity towards osteoblasts. Most importantly, enrichment of this biomaterial with a supplementary underlayer of nano hydroxyapatite allowed for the preservation of antibacterial properties and also a decrease in the cytotoxicity towards bone cells, associated with the presence of a nano zinc oxide-silver layer. Thus, the final structure of the composite poly (D,L-lactic acid)/poly (lactic-co-glycolic acid)/nano hydroxyapatite/nano zinc oxide-silver seems to be a promising construct for tissue engineering products, especially guided tissue regeneration/guided bone regeneration membranes. Nevertheless, additional research is needed in order to improve the developed construct, which will simultaneously protect the biomaterial from bacterial colonization and enhance the bone regeneration properties.

Nano-hydroxyapatite-evoked immune response synchronized with controllable immune adjuvant release for strengthening melanoma-specific growth inhibition.

Concerns about the potential systematic toxicity limit the extensive application of traditional therapeutic drugs for melanoma therapy, nano-hydroxyapatite (nHA) with good biocompatibility and anti-tumor ability could be an alternative choice. In this study, nHA was employed as an anti-tumor biomaterial due to its tumor-specific toxicity. Meanwhile, granulocyte-macrophage colony-stimulating factor (GM-CSF) served as the immune adjuvant to activate the immune response. The delivery platform was fabricated by co-encapsulation of both nHA and GM-CSF into a biocompatible thermosensitive PLGA-PEG-PLGA hydrogel. The results showed that the bio-activities of nHA and GM-CSF could be well-maintained within the hydrogel. Interestingly, the addition of nHA could attenuate the burst release of GM-CSF due to possible protein absorption capacity of nHA, which is beneficial for GM-CSF sustainable release at the tumor site, achieving boosted and prolonged anti-tumor immunity. The in vitro and in vivo data demonstrated that nHA/GM-CSF hydrogel exhibited greater potency to inhibit tumor growth via enhanced CD8+ T-cell response compared with hydrogel and nHA hydrogel groups, contributed by the synergistic effects of nHA and GM-CSF. Overall, the strategy combining nHA and immune adjuvant shows great promise, which largely broadens the choice of combinational therapies for melanoma. STATEMENT OF SIGNIFICANCE: Nano-hydroxyapatite (nHA) has been confirmed to specifically inhibit melanoma tumor growth and induce immune response. However, its antitumor efficiency and immunity-evoking capacity are limited. In this study, granulocyte-macrophage colony-stimulating factor (GM-CSF) was introduced to serve as the immune adjuvant. Both of them were encapsulated into a biocompatible thermosensitive PLGA-PEG-PLGA hydrogel. The addition of nHA could attenuate the burst release of GM-CSF due to the interaction with nHA, which is beneficial for GM-CSF sustainable release at tumor site, achieving boosted and prolonged anti-tumor immunity. Anti-tumor immune response could be activated due to the release of tumor-associated antigen and tumor debris induced by the specifically tumor inhibition effect of nHA and GM-CSF. The combination of nHA and GM-CSF could play synergistic inhibiting effect on tumor growth via boosting and prolonging anti-tumor immunity.

Modulatory activity of a bovine hydrolyzed collagen-hydroxyapatite food complex on human primary osteoblasts after simulating its gastrointestinal digestion and absorption.

Introduction: Introduction: osteoporosis is the most prevalent bone disease and one of the main causes of chronic disability in middle and advanced ages. Conventional pharmacological treatments are still limited, and their prolonged use can cause adverse effects that motivate poor adherence to treatment. Nutritional strategies are traditionally based on supplementing the diet with calcium and vitamin D. Recent studies confirm that the results of this supplementation are significantly improved if it is accompanied by the intake of oral hydrolyzed collagen. Objective: to evaluate the possible in vitro osteogenic activity of a peptide-mineral complex formed by bovine hydrolyzed collagen and bovine hydroxyapatite (Phoscollagen®, PHC®). Methods: the digestion and absorption of PHC® were simulated using the dynamic gastrointestinal digester of AINIA and Caco-2 cell model, respectively. Primary cultures of human osteoblasts were treated with the resulting fraction of PHC® and changes were evaluated in the proliferation of preosteoblasts and in the mRNA expression of osteogenic biomarkers at different stages of osteoblast maturation: Runt-related transcription factor 2 (Runx2), alkaline phosphatase (ALP), osteocalcin (OC) and type I collagen (ColA1). Results: an increase in preosteoblastic proliferation was observed (p ≤ 0,05). No changes were detected in the biomarkers of osteoblasts with 5 days of differentiation, but were with 14 days, registering an increase in Runx2 (p = 0.0008), ColA1 (p = 0.035), OC (p = 0.027) and ALP (without significance). Conclusion: these results show that the PHC® peptide-mineral complex stimulates the activity of mature osteoblasts, being capable of promoting bone formation.

Introducción: Introducción: la osteoporosis es la enfermedad ósea más prevalente y una de las principales causas de discapacidad crónica en las edades medias y avanzadas. Los tratamientos farmacológicos convencionales aún son limitados y su uso prolongado puede provocar efectos adversos que motiven baja adherencia al tratamiento. Las estrategias nutricionales se basan tradicionalmente en suplementar la dieta con calcio y vitamina D. Estudios recientes confirman que los resultados de esta suplementación mejoran significativamente si se acompaña de la ingesta de colágeno hidrolizado oral. Objetivo: evaluar la posible actividad osteogénica in vitro de un complejo péptido-mineral formado por colágeno hidrolizado e hidroxiapatita bovinos (Phoscollagen®, PHC®). Métodos: se simuló la digestión y absorción de PHC® utilizando el digestor dinámico gastrointestinal de AINIA y el modelo celular Caco-2, respectivamente. Cultivos primarios de osteoblastos humanos se trataron con la fracción resultante de PHC® y se evaluaron los cambios en la proliferación de los preosteoblastos y en la expresión del ARNm de los biomarcadores osteogénicos en diferentes etapas de maduración de los osteoblastos: factor de transcripción 2 relacionado con Runt (Runx2), fosfatasa alcalina (ALP), osteocalcina (OC) y colágeno tipo I (ColA1). Resultados: se observó un incremento de la proliferación preosteoblástica (p ≤ 0,05). No se detectaron cambios en los biomarcadores de osteoblastos con 5 días de diferenciación, pero sí con 14 días, registrándose un aumento de Runx2 (p = 0,0008), ColA1 (p = 0,035), OC (p = 0,027) y ALP (sin significancia). Conclusión: estos resultados muestran que el complejo péptido-mineral PHC® estimula la actividad de los osteoblastos maduros, siendo susceptible de promover la formación ósea.

Synergistic impact of platelet rich plasma-heparin sulfate with hydroxyapatite/zirconia on the osteoblast differentiation potential of adipose-derived mesenchymal stem cells.

3D porous hydroxyapatite (HA) has been reinforced by zirconia (ZrO2) coating and impregnation with a combination of platelet rich plasma (PRP) as a source of growth factors (GFs) and Heparin sulfate (HS) to sustain the release of GFs. Adipose mesenchymal stem cells (ADMSCs) were characterized by flow cytometry for CD (cluster of differentiation) 44, CD105, CD106, CD34 and CD144, along with checking the multipotency by differentiation into the adipocytes and osteoblasts. Then, they were cultured on the scaffold treated with and without osteogenic media on days 7, 14 and 21. Electron micrograph and PKH staining show that the ADMSCs have a fusiform phenotype in the absence of osteogenic induction. Cell viability assay shows a higher number of the viable cells on the PRP-containing scaffolds than PRP-free scaffolds on day 7. Colorimetric evaluation, quantitative RT-PCR and immunocytochemistry demonstrate that PRP and HS significantly elevate the alkaline phosphatase enzyme activity and also accelerate the production of both early and mid-osteogenic markers, including collagen I and osteopontin expression with and without osteogenic conditions. The PRP-HS also accelerates the expression of the late osteogenic marker, osteocalcin, in both mRNA and protein level expression with a peak on day 21. In conclusion, supplementation of HA/ZrO2 with PRP/HS has a synergistic impact on the ADMSCs, even in the absence of chemical induction. It seems that HA/ZrO2/PRP/HS scaffold provides a higher osteoconductive microenvironment for stem cell differentiation to osteoblasts.

Engineered Hydroxyapatite Nanoadjuvants with Controlled Shape and Aspect Ratios Reveal Their Immunomodulatory Potentials.

Hydroxyapatite (HAP) has been formulated as adjuvants in vaccines for human use. However, the optimal properties required for HAP nanoparticles to elicit adjuvanticity and the underlying immunopotentiation mechanisms have not been fully elucidated. Herein, a library of HAP nanorods and nanospheres was synthesized to explore the effect of the particle shape and aspect ratio on the immune responses in vitro and adjuvanticity in vivo. It was demonstrated that long aspect ratio HAP nanorods induced a higher degree of cell membrane depolarization and subsequent uptake, and the internalized particles elicited cathepsin B release and mitochondrial reactive oxygen species generation, which further led to pro-inflammatory responses. Furthermore, the physicochemical property-dependent immunostimulation capacities were correlated with their humoral responses in a murine hepatitis B surface antigen immunization model, with long aspect ratio HAP nanorods inducing higher antigen-specific antibody productions. Importantly, HAP nanorods significantly up-regulated the IFN-γ secretion and CD107α expression on CD8+ T cells in immunized mice. Further mechanistic studies demonstrated that HAP nanorods with defined properties exerted immunomodulatory effects by enhanced antigen persistence and immune cell recruitments. Our study provides a rational design strategy for engineered nanomaterial-based vaccine adjuvants.

Concentration-Dependent Multi-Potentiality of L-Arginine: Antimicrobial Effect, Hydroxyapatite Stability, and MMPs Inhibition.

This study's objective was to examine L-arginine (L-arg) supplementation's effect on mono-species biofilm (Streptococcus mutans/Streptococcus sanguinis) growth and underlying enamel substrates. The experimental groups were 1%, 2%, and 4% arg, and 0.9% NaCl was used as the vehicle control. Sterilised enamel blocks were subjected to 7-day treatment with test solutions and S. mutans/S. sanguinis inoculum in BHI. Post-treatment, the treated biofilms stained for live/dead bacterial cells were analysed using confocal microscopy. The enamel specimens were analysed using X-ray diffraction crystallography (XRD), Raman spectroscopy (RS), and transmission electron microscopy (TEM). The molecular interactions between arg and MMP-2/MMP-9 were determined by computational molecular docking and MMP assays. With increasing arg concentrations, bacterial survival significantly decreased (p < 0.05). The XRD peak intensity with 1%/2% arg was significantly higher than with 4% arg and the control (p < 0.05). The bands associated with the mineral phase by RS were significantly accentuated in the 1%/2% arg specimens compared to in other groups (p < 0.05). The TEM analysis revealed that 4% arg exhibited an ill-defined shape of enamel crystals. Docking of arg molecules to MMPs appears feasible, with arg inhibiting MMP-2/MMP-9 (p < 0.05). L-arginine supplementation has an antimicrobial effect on mono-species biofilm. L-arginine treatment at lower (1%/2%) concentrations exhibits enamel hydroxyapatite stability, while the molecule has the potential to inhibit MMP-2/MMP-9.

Systemic Administration of PTH Supports Vascularization in Segmental Bone Defects Filled with Ceramic-Based Bone Graft Substitute.

Non-unions continue to present a challenge to trauma surgeons, as current treatment options are limited, duration of treatment is long, and the outcome often unsatisfactory. Additionally, standard treatment with autologous bone grafts is associated with comorbidity at the donor site. Therefore, alternatives to autologous bone grafts and further therapeutic strategies to improve on the outcome and reduce cost for care providers are desirable. In this study in Sprague-Dawley rats we employed a recently established sequential defect model, which provides a platform to test new potential therapeutic strategies on non-unions while gaining mechanistic insight into their actions. The effects of a combinatorial treatment of a bone graft substitute (HACaS+G) implantation and systemic PTH administration was assessed by µ-CT, histological analysis, and bio-mechanical testing and compared to monotreatment and controls. Although neither PTH alone nor the combination of a bone graft substitute and PTH led to the formation of a stable union, our data demonstrate a clear osteoinductive and osteoconductive effect of the bone graft substitute. Additionally, PTH administration was shown to induce vascularization, both as a single adjuvant treatment and in combination with the bone graft substitute. Thus, systemic PTH administration is a potential synergistic co-treatment to bone graft substitutes.

Bone regeneration in both small and large preclinical bone defect models using an injectable polymer-based substitute containing hydroxyapatite and reconstituted with saline or autologous blood.

Microbeads consisting of pullulan and dextran supplemented with hydroxyapatite have recently been developed for bone tissue engineering applications. Here, we evaluate the bone formation in two different preclinical models after injection of microbeads reconstituted with either saline buffer or autologous blood. Addition of saline solution or autologous blood to dried microbeads packaged into syringes allowed an easy injection. In the first rat bone defect model performed in the femoral condyle, microcomputed tomography performed after 30 and 60 days revealed an important mineralization process occurring around and within the core of the microbeads in both conditions. Bone volume/total volume measurements revealed no significant differences between the saline solution and the autologous blood groups. Histologically, osteoid tissue was evidenced around and in contact of the microbeads in both conditions. Using the sinus lift model performed in sheep, cone beam computed tomography revealed an important mineralization inside the sinus cavity for both groups after 3 months of implantation. Representative Masson trichrome staining images showed that bone formation occurs at the periphery and inside the microbeads in both conditions. Quantitative evaluation of the new bone formation displayed no significant differences between groups. In conclusion, reconstitution of microbeads with autologous blood did not enhance the regenerative capacity of these microbeads compared to the saline buffer group. This study is of particular interest for clinical applications in oral and maxillofacial surgery.