Comparison of quartz and sapphire optical chambers for infrared laser sealing of vascular tissues using a reciprocating, side-firing optical fiber: Simulations and experiments.

INTRODUCTION: Infrared (IR) lasers are being tested as an alternative to radiofrequency (RF) and ultrasonic (US) surgical devices for hemostatic sealing of vascular tissues. In previous studies, a side-firing optical fiber with elliptical IR beam output was reciprocated, producing a linear IR laser beam pattern for uniform sealing of blood vessels. Technical challenges include limited field-of-view of vessel position within the metallic device jaws, and matching fiber scan length to variable vessel sizes. A transparent jaw may improve visibility and enable custom treatment. METHODS: Quartz and sapphire square optical chambers (2.7 × 2.7 × 25 [mm3 ] outer dimensions) were tested, capable of fitting into a 5-mm-OD laparoscopic device. A 1470 nm laser was used for optical transmission studies. Razor blade scans and an IR beam profiler acquired fiber (550-µm-core/0.22NA) output beam profiles. Thermocouples recorded peak temperatures and cooling times on internal and external chamber surfaces. Optical fibers with angle polished distal tips delivered 94% of light at a 90° angle. Porcine renal arteries with diameters of 3.4 ± 0.7 mm (n = 13) for quartz and 3.2 ± 0.7 mm (n = 14) for sapphire chambers (p > 0.05), were sealed using 30 W for 5 s. RESULTS: Reflection losses at material/air interfaces were 3.3% and 7.4% for quartz and sapphire. Peak temperatures on the external chamber surface averaged 74 ± 8°C and 73 ± 10°C (p > 0.05). Times to cool down to 37°C measured 13 ± 4 s and 27 ± 7 s (p < 0.05). Vessel burst pressures (BP) averaged 883 ± 393 mmHg and 412 ± 330 mmHg (p < 0.05). For quartz, 13/13 (100%) vessels were sealed (BP > 360 mmHg), versus 9/14 (64%) for sapphire. Computer simulations for the quartz chamber yielded peak temperatures (78°C) and cooling times (16 s) similar to experiments. CONCLUSIONS: Quartz is an inexpensive material for use in a laparoscopic device jaw, providing more consistent vessel seals and faster cooling times than sapphire and current RF and US devices.

Comparative Evaluations on Real-Time Monitoring of Temperature Sensors during Endoscopic Laser Application.

Temperature sensors, such as Fiber Bragg Grating (FBG) and thermocouple (TC), have been widely used for monitoring the interstitial tissue temperature during laser irradiation. The aim of the current study was to compare the performance of both FBG and TC in real-time temperature monitoring during endoscopic and circumferential laser treatment on tubular tissue structure. A 600-µm core-diameter diffusing applicator was employed to deliver 980-nm laser light (30 W for 90 s) circumferentially for quantitative evaluation. The tip of the TC was covered with a white tube (W-TC) in order to prevent direct light absorption and to minimize temperature overestimation. The temperature measurements in air demonstrated that the measurement difference in the temperature elevations was around 3.5 °C between FBG and W-TC. Ex vivo porcine liver tests confirmed that the measurement difference became lower (less than 1 °C). Ex vivo porcine esophageal tissue using a balloon-integrated catheter exhibited that both FBG and W-TC consistently showed a comparable trend of temperature measurements during laser irradiation (~2 °C). The current study demonstrated that the white tube-covered TC could be a feasible sensor to monitor interstitial tissue temperature with minimal overestimation during endoscopic laser irradiation. Further in vivo studies on gastroesophageal reflux disease will investigate the performance of the W-TC to monitor the temperature of the esophageal mucosa surface in real-time mode to warrant the safety of endoscopic laser treatment.

A biodegradable, flexible photonic patch for in vivo phototherapy.

Diagnostic and therapeutic illumination on internal organs and tissues with high controllability and adaptability in terms of spectrum, area, depth, and intensity remains a major challenge. Here, we present a flexible, biodegradable photonic device called iCarP with a micrometer scale air gap between a refractive polyester patch and the embedded removable tapered optical fiber. ICarP combines the advantages of light diffraction by the tapered optical fiber, dual refractions in the air gap, and reflection inside the patch to obtain a bulb-like illumination, guiding light towards target tissue. We show that iCarP achieves large area, high intensity, wide spectrum, continuous or pulsatile, deeply penetrating illumination without puncturing the target tissues and demonstrate that it supports phototherapies with different photosensitizers. We find that the photonic device is compatible with thoracoscopy-based minimally invasive implantation onto beating hearts. These initial results show that iCarP could be a safe, precise and widely applicable device suitable for internal organs and tissue illumination and associated diagnosis and therapy.

Optical Fiber Distributed Sensing Network for Thermal Mapping in Radiofrequency Ablation Neighboring a Blood Vessel.

Radiofrequency ablation (RFA) is a minimally invasive form of thermotherapy with great potential in cancer care, having the capability of selectively ablating tumoral masses with a surface area of several cm2. When performing RFA in the proximity of a blood vessel, the heating profile changes due to heat dissipation, perfusion, and impedance changes. In this work, we provide an experimental framework for the real-time evaluation of 2D thermal maps in RFA neighboring a blood vessel; the experimental setup is based on simultaneous scanning of multiple fibers in a distributed sensing network, achieving a spatial resolution of 2.5 × 4 mm2 in situ. We also demonstrate an increase of ablating potential when injecting an agarose gel in the tissue. Experimental results show that the heat-sink effect contributes to a reduction of the ablated region around 30-60% on average; however, the use of agarose significantly mitigates this effect, enlarging the ablated area by a significant amount, and ablating an even larger surface (+15%) in the absence of blood vessels.

Highly sensitive SERS detection in a non-volatile liquid-phase system with nanocluster-patterned optical fiber SERS probes.

The use of surface-enhanced Raman scattering (SERS) spectroscopy for the detection of substances in non-volatile systems, such as edible oil and biological cells, is an important issue in the fields of food safety and biomedicine. However, traditional dry-state SERS detection with planar SERS substrates is not suitable for highly sensitive and rapid SERS detection in non-volatile liquid-phase systems. In this paper, we take contaminant in edible oil as an example and propose an in situ SERS detection method for non-volatile complex liquid-phase systems with high-performance optical fiber SERS probes. Au-nanorod clusters are successfully prepared on optical fiber facet by a laboratory-developed laser-induced dynamic dip-coating method, and relatively high detection sensitivity (LOD of 2.4 × 10-6 mol/L for Sudan red and 3.6 × 10-7 mol/L for thiram in sunflower oil) and good reproducibility (RSD less than 10%) are achieved with a portable Raman spectrometer and short spectral integration time of 10 s even in complex edible oil systems. Additionally, the recovery rate experiment indicates the reliability and capability of this method for quantitative detection applications. This work provides a new insight for highly sensitive and rapid SERS detection in non-volatile liquid-phase systems with optical fiber SERS probes and may find important practical applications in food safety and biomedicine.

Ultrasensitive evanescent wave optical fiber aptasensor for online, continuous, type-specific detection of sulfonamides in environmental water.

Sensors capable for online continuous monitoring of total sulfonamides in environmental waters are highly desired due to their adverse effects on ecosystem, unexpected concentration fluctuation, and diversity. At present, no sensor with this capability has been reported. In this study, we evaluated the cross reactivity (CR) of the previously reported sulfadimethoxine-binding aptamer using DNase I assay and found that the aptamer was type-specific to sulfonamides. We then fabricated the first type-specific sulfonamide sensor, where the aptamer was immobilized on the optical fiber of the evanescent wave sensor, followed by the surface coating with Tween 80. The competitive binding of sulfonamides and Cy5.5 labeled complementary DNA enabled the low femtomolar to picomolar sensitivity and the detection of total 14 sulfonamides spiked in the lake water. The sensor also exhibited high selectivity, regeneration capability (40 cycles), stability (65 days), and short detection time (5 min). In addition, we found that the CRs were greatly dependent on the buffer composition. By performing the parallel detections in two buffers, the sensors detected 18 out of the 24 sulfonamides with the diversity coverage higher than commercial ELISA kits. Our aptasensor fills the technical gap for continuous monitoring of total sulfonamides in environmental waters.

Selective detection of diethanolamine utilizing an LMR/LSPR-based optical fiber sensor.

Diethanolamine (DEA) is used for amine wash to remove toxic gases such as hydrogen sulphide (H2S) while processing crude oil and in other pharmaceutical products. The detection of diethanolamine is of prime importance to avoid its harmful impact. In this study, we have designed a lossy mode resonance (LMR)-based optical fiber sensor for the detection of DEA. An optical fiber probe was fabricated by coating a bulk layer of titanium dioxide (TiO2) on the core of the optical fiber (probe-1). To extend this study, we prepared biosynthesised gold nanoparticles and coated them on to the top of the TiO2-layer-coated probe (probe-2). The surface structure was confirmed using characterization techniques such as FESEM, HRTEM and UV-visible spectroscopy. Further, a comparative study among probe-1 and probe-2 has been carried out in terms of their performance parameters such as sensitivity, figure of merit, limit of detection, repeatability and response time. The sensitivity of the TiO2 bulk layer/AuNP bilayer-coated optical fiber probe (probe-2) was observed to be 16 079.63 nm RIU-1 (0.074 nm mM-1), which was approximately double the sensitivity of the TiO2 bulk layer-coated optical fiber probe (probe-1). Selectivity experiments were also performed to confirm the high sensitivity of the sensor towards DEA.

An Optical Fiber Sensor for Uranium Detection in Water.

An optical sensor for uranyl has been prepared based on a gold-plated D-shaped plastic optical fiber (POF) combined with a receptor consisting of a bifunctional synthetic molecule, 11-mercaptoundecylphosphonic acid (MUPA), with a phosphonic group for complexing the considered ion, and a sulfide moiety through which the molecule is fixed at the gold resonant surface as a molecular layer in an easy and reproducible way. The sensor is characterized by evaluating the response in function of the uranyl concentration in aqueous solutions of different compositions and real-life samples, such as tap water and seawater. The mechanism of the uranyl/MUPA interaction was investigated. Two different kinds of interactions of uranyl with the MUPA layer on gold from water are observed: a strong one and a weak one. In the presence of competing metal ions as Ca2+ and Mg2+, only the strong interaction takes place, with a high affinity constant (around 107 M-1), while a somewhat lower constant (i.e., around 106 M-1) is obtained in the presence of Mg2+ which forms stronger complexes with MUPA than Ca2+. Due to the high affinity and the good selectivity of the recognition element MUPA, a detection limit of a few µg L-1 is reached directly in natural water samples without any time-consuming sample pretreatment, making it possible for rapid, in situ controls of uranyl by the proposed sensor.

Monitoring of Ultra-High Dose Rate Pulsed X-ray Facilities with Radioluminescent Nitrogen-Doped Optical Fiber.

We exploited the potential of radiation-induced emissions (RIEs) in the visible domain of a nitrogen-doped, silica-based, multimode optical fiber to monitor the very high dose rates associated with experiments at different pulsed X-ray facilities. We also tested this sensor at lower dose rates associated with steady-state X-ray irradiation machines (up to 100 keV photon energy, mean energy of 40 keV). For transient exposures, dedicated experimental campaigns were performed at ELSA (Electron et Laser, Source X et Applications) and ASTERIX facilities from CEA (Commissariat à l'Energie Atomique-France) to characterize the RIE of this fiber when exposed to X-ray pulses with durations of a few µs or ns. These facilities provide very large dose rates: in the order of MGy(SiO2)/s for the ELSA facility (up to 19 MeV photon energy) and GGy(SiO2)/s for the ASTERIX facility (up to 1 MeV). In both cases, the RIE intensities, mostly explained by the fiber radioluminescence (RIL) around 550 nm, with a contribution from Cerenkov at higher fluxes, linearly depend on the dose rates normalized to the pulse duration delivered by the facilities. By comparing these high dose rate results and those acquired under low-dose rate steady-state X-rays (only RIL was present), we showed that the RIE of this multimode optical fiber linearly depends on the dose rate over an ultra-wide dose rate range from 10-2 Gy(SiO2)/s to a few 109 Gy(SiO2)/s and photons with energy in the range from 40 keV to 19 MeV. These results demonstrate the high potential of this class of radiation monitors for beam monitoring at very high dose rates in a very large variety of facilities as future FLASH therapy facilities.

Proof of concept for the sapphire scalpel combining tissue dissection and optical diagnosis.

OBJECTIVES: The development of compact diagnostic probes and instruments with an ability to direct access to organs and tissues and integration of these instruments into surgical workflows is an important task of modern physics and medicine. The need for such tools is essential for surgical oncology, where intraoperative visualization and demarcation of tumor margins define further prognosis and survival of patients. In this paper, the possible solution for this intraoperative imaging problem is proposed and its feasibility to detect tumorous tissue is studied experimentally. METHODS: For this aim, the sapphire scalpel was developed and fabricated using the edge-defined film-fed growth technique aided by mechanical grinding, polishing, and chemical sharpening of the cutting edge. It possesses optical transparency, mechanical strength, chemical inertness, and thermal resistance alongside the presence of the as-grown hollow capillary channels in its volume for accommodating optical fibers. The rounding of the cutting edge exceeds the same for metal scalpels and can be as small as 110 nm. Thanks to these features, sapphire scalpel combines tissue dissection with light delivering and optical diagnosis. The feasibility for the tumor margin detection was studied, including both gelatin-based tissue phantoms and ex vivo freshly excised specimens of the basal cell carcinoma from humans and the glioma model 101.8 from rats. These tumors are commonly diagnosed either non-invasively or intraoperatively using different modalities of fluorescence spectroscopy and imaging, which makes them ideal candidates for our feasibility test. For this purpose, fiber-based spectroscopic measurements of the backscattered laser radiation and the fluorescence signals were carried out in the visible range. RESULTS: Experimental studies show the feasibility of the proposed sapphire scalpel to provide a 2-mm-resolution of the tumor margins' detection, along with an ability to distinguish the tumor invasion region, which results from analysis of the backscattered optical fields and the endogenous or exogenous fluorescence data. CONCLUSIONS: Our findings justified a strong potential of the sapphire scalpel for surgical oncology. However, further research and engineering efforts are required to optimize the sapphire scalpel geometry and the optical diagnosis protocols to meet the requirements of oncosurgery, including diagnosis and resection of neoplasms with different localizations and nosologies.

[Ultra-fast response polymer optical fiber oxygen measurement device and its preliminary experimental report on continuous dynamic change of arterial oxygen partial pressure under mechanical ventilation in living animals].

Objective: We tried to implant the ultra-fast polymer optical fiber chemical oxygen sensor （POFCOS） into arterial blood vessel,connect with photoelectric conversion measurement system to record the continuous dynamic rapid changes of arterial PO2(PaO2) in whole living animals. It should be the experimental evidence for the new theory of holistic integrative physiology and medicine(HIPM) forexplain the mechanism of respiratory control and regulation in whole circusof respiration-circulation-metabolism. Methods: ①Fabrication of ultrafast POFCOS, calibration and its measuring system: The distal part of 2 m optical fiber was heated and pulled until it became a tapered tip. After cleaning and drying, the tip of 1 mm tapered optical fiber was dip-coated into the luminophore doped polymer solution, then was slowly pumped out while solvent was quickly evaporated to form an oxygen sensing tip, which was dried at room temperature for 24 hours. ②Animal experiments: Under general anesthesia and intubation, goatwas mechanically ventilated with 40%~60% oxygen. We exposed both right and left carotid arteries and the left femoral artery by skin cutting, and inserted the POFCOS directly into the arteries via indwelling catheter. The end of POFCOS were connected to the personal computer through optical fiber, excitation and detection Y-type optical fiber coupler through photoelectric conversion, so as we can realize the continuous dynamic response of living goat carotid PaO2 under mechanical ventilation. We mainly analyzed the intra-breath wave-form alternate increase and decrease of PaO2 and their time delay between lung and carotid arteries.We completes breathing control whole loop to explain the mechanism of mutual breathing and the switching of inspiration and exhalation. Results: The POFCOS has a very fast T90 response time was set 100 ms for liquid. When the heart rate of 40%~60% oxygen mechanical ventilated living goat was ~110 bpm, the PaO2 of left and right carotid artery showed a same wave-sizeup and down following with the inspiration and expiration of ventilator, with a range of up to 15 mmHg. There weresignificant noises of PaO2 change recorded in the left femoral artery. The lung-carotid artery time delay is 1.5~1.7 s after inhalation and exhalation, PaO2 at both left and right carotid arteries starts toincrease and decrease. After two-three heartbeats after the start of lung ventilation, thealternate up-down wave-form information of the arterialized pulmonary vein blood after pulmonary capillaries waspumpedby left ventricle to the position of peripheral chemoreceptors,thus realizing the whole cycle of inhalation and exhalation. It alternately interrupted inhalation, i.e. switching inhalation to exhalation, and then interrupted exhalation,i.e. switching exhalation to inhalation. Conclusion: The ultra-fast reactive implantableoxygen sensor and its measuring system can measure the physiological waveform changes of PaO2 in living animals, which can provide experimental evidence for explaining the mechanism of switching of inspiration-expiration in HIPM.

Optical fibers for endoscopic high-power Er:YAG laserosteotomy.

SIGNIFICANCE: The highest absorption peaks of the main components of bone are in the mid-infrared region, making Er:YAG and CO2 lasers the most efficient lasers for cutting bone. Yet, studies of deep bone ablation in minimally invasive settings are very limited, as finding suitable materials for coupling high-power laser light with low attenuation beyond 2 µm is not trivial. AIM: The first aim of this study was to compare the performance of different optical fibers in terms of transmitting Er:YAG laser light with a 2.94-µm wavelength at high pulse energy close to 1 J. The second aim was to achieve deep bone ablation using the best-performing fiber, as determined by our experiments. APPROACH: In our study, various optical fibers with low attenuation (λ = 2.94 µm) were used to couple the Er:YAG laser. The fibers were made of germanium oxide, sapphire, zirconium fluoride, and hollow-core silica, respectively. We compared the fibers in terms of transmission efficiency, resistance to high Er:YAG laser energy, and bending flexibility. The best-performing fiber was used to achieve deep bone ablation in a minimally invasive setting. To do this, we adapted the optimal settings for free-space deep bone ablation with an Er:YAG laser found in a previous study. RESULTS: Three of the fibers endured energy per pulse as high as 820 mJ at a repetition rate of 10 Hz. The best-performing fiber, made of germanium oxide, provided higher transmission efficiency and greater bending flexibility than the other fibers. With an output energy of 370 mJ per pulse at 10 Hz repetition rate, we reached a cutting depth of 6.82 ± 0.99 mm in sheep bone. Histology image analysis was performed on the bone tissue adjacent to the laser ablation crater; the images did not show any structural damage. CONCLUSIONS: The findings suggest that our prototype could be used in future generations of endoscopic devices for minimally invasive laserosteotomy.

4,6,4'-Trimethylangelicin Photoactivated by Blue Light Might Represent an Interesting Option for Photochemotherapy of Non-Invasive Bladder Carcinoma: An In Vitro Study on T24 Cells.

Photodynamic therapy (PDT) is frequently used to treat non-muscle invasive bladder cancer due its low toxicity and high selectivity. Since recurrence often occurs, alternative approaches and/or designs of combined therapies to improve PDT effectiveness are needed. This work aimed to evaluate the cytotoxicity of 4,6,4'-trimethylangelicin (TMA) photoactivated by blue light (BL) on human bladder cancer T24 cells and investigate the mechanisms underlying its biological effects. TMA/BL exerted antiproliferative activity through the induction of apoptosis without genotoxicity, as demonstrated by the expression levels of phospho-H2AX, an indicator of DNA double-stranded breaks. It also modulated the Wnt canonical signal pathway by increasing the phospho-ß-catenin and decreasing the nuclear levels of ß-catenin. The inhibition of this pathway was due to the modulation of the GSK3ß phosphorylation state (Tyr 216) that induces a proteasomal degradation of ß-catenin. Indeed, a partial recovery of nuclear ß-catenin expression and reduction of its phosphorylated form after treatment with LiCl were detected. As demonstrated by RT-PCR and cytofluorimetric analysis, TMA/BL also decreased the expression of CD44v6, a marker of cancer stem cells. Taken together, our data suggest that TMA photoactivated by BL may represent an interesting option for the photochemotherapy of noninvasive bladder carcinomas, since this treatment is able to inhibit key pathways for tumour growth and progression in the absence of genotoxic effects.

Photobiomodulation by a new optical fiber device: analysis of the in vitro impact on proliferation/migration of keratinocytes and squamous cell carcinomas cells stressed by X-rays.

Photobiomodulation-based (PBM-based) therapies show promising results in mucositis and dermatitis treatment by stimulating wound healing mechanisms such as cell proliferation and migration. The aim of the present study is to investigate the in vitro effects of CareMin650 on the proliferation and migration of two different types of cells, namely cancer and non-cancer cells, with or without X-ray radiation. Study design used PBM through a combination of 0-3-6 J/cm2 doses-with or without X-ray radiation-on the proliferation and migration capabilities of a keratinocyte cell line (HaCaT) and a squamous cell carcinoma line (SCC61). PBM is delivered by a new woven optical fiber device, namely CareMin650 prototype (light emission by LEDs (light-emitting diodes), peak at 660 nm, irradiance of 21.6 mW/cm2). The effectiveness of PBM to increase HaCaT proliferation and migration (with or without X-ray radiation) supports the capability of PBM to favor wound healing. It also highlights that PBM does not provide any anti-radiation effect to previously X-rays radiated SCC (p < 0.001). Such data supports the beneficial effect of PBM delivered by an optical fiber device to heal wounds, without promoting cancer development.

Cytochrome c oxidase-modulatory near-infrared light penetration into the human brain: Implications for the noninvasive treatment of ischemia/reperfusion injury.

Near-infrared light (IRL) has been evaluated as a therapeutic for a variety of pathological conditions, including ischemia/reperfusion injury of the brain, which can be caused by an ischemic stroke or cardiac arrest. Strategies have focused on modulating the activity of mitochondrial electron transport chain (ETC) enzyme cytochrome c oxidase (COX), which has copper centers that broadly absorb IRL between 700 and 1,000 nm. We have recently identified specific COX-inhibitory IRL wavelengths that are profoundly neuroprotective in rodent models of brain ischemia/reperfusion through the following mechanism: COX inhibition by IRL limits mitochondrial membrane potential hyperpolarization during reperfusion, which otherwise causes reactive oxygen species (ROS) production and cell death. Prior to clinical application of IRL on humans, IRL penetration must be tested, which may be wavelength dependent. In the present study, four fresh (unfixed) cadavers and isolated cadaver tissues were used to examine the transmission of infrared light through human biological tissues. We conclude that the transmission of 750 and 940 nm IRL through 4 cm of cadaver head supports the viability of IRL to treat human brain ischemia/reperfusion injury and is similar for skin with different skin pigmentation. We discuss experimental difficulties of working with fresh cadavers and strategies to overcome them as a guide for future studies.

Pain modulation effect on motor cortex after optogenetic stimulation in shPKCγ knockdown dorsal root ganglion-compressed Sprague-Dawley rat model.

Neuropathic pain can be generated by chronic compression of dorsal root ganglion (CCD). Stimulation of primary motor cortex can disrupt the nociceptive sensory signal at dorsal root ganglion level and reduce pain behaviors. But the mechanism behind it is still implicit. Protein kinase C gamma is known as an essential enzyme for the development of neuropathic pain, and specific inhibitor of protein kinase C gamma can disrupt the sensory signal and reduce pain behaviors. Optogenetic stimulation has been emerged as a new and promising conducive method for refractory neuropathic pain. The aim of this study was to provide evidence whether optical stimulation of primary motor cortex can modulate chronic neuropathic pain in CCD rat model. Animals were randomly divided into CCD group, sham group, and control group. Dorsal root ganglion-compressed neuropathic pain model was established in animals, and knocking down of protein kinase C gamma was also accomplished. Pain behavioral scores were significantly improved in the short hairpin Protein Kinase C gamma knockdown CCD animals during optic stimulation. Ventral posterolateral thalamic firing inhibition was also observed during light stimulation on motor cortex in CCD animal. We assessed alteration of pain behaviors in pre-light off, stimulation-light on, and post-light off state. In vivo extracellular recording of the ventral posterolateral thalamus, viral expression in the primary motor cortex, and protein kinase C gamma expression in dorsal root ganglion were investigated. So, optical cortico-thalamic inhibition by motor cortex stimulation can improve neuropathic pain behaviors in CCD animal, and knocking down of protein kinase C gamma plays a conducive role in the process. This study provides feasibility for in vivo optogenetic stimulation on primary motor cortex of dorsal root ganglion-initiated neuropathic pain.

Textile-integrated polymer optical fibers for healthcare and medical applications.

With ever growing interest in far-reaching solutions for pervasive healthcare and medicine, polymer optical fibers have been rendered into textile forms. Having both fiber-optic functionalities and traditional fabric-like comfort, textile-integrated polymer optical fibers have been advocated to remove the technical barriers for long-term uninterrupted health monitoring and treatment. In this context, this paper spotlights and reviews the recently developed textile-integrated polymer optical fibers in conjunction with fabrication techniques, applications in long-term continuous health monitoring and treatment, and future perspectives in the vision of mobile health (mHealth), as well as the introductory basics of polymer optical fibers. It is designed to serve as a topical guidepost for scientists and engineers on this highly interdisciplinary and rapidly growing topic.

Inorganic scintillation detectors for 192Ir brachytherapy.

Many brachytherapy (BT) errors could be detected with real-time in vivo dosimetry technology. Inorganic scintillation detectors (ISDs) have demonstrated promising capabilities for BT, because some ISD materials can generate scintillation signals large enough that (a) the background signal emitted in the fiber-optic cable (stem signal) is insignificant, and (b) small detector volumes can be used to avoid volume averaging effects in steep dose gradients near BT sources. We investigated the characteristics of five ISD materials to identify one that is appropriate for BT. ISDs consisting of a 0.26 to 1.0 mm3 volume of ruby (Al2O3:Cr), a mixture of Y2O3:Eu and YVO4:Eu, ZnSe:O, or CsI:Tl coupled to a fiber-optic cable were irradiated in a water-equivalent phantom using a high-dose-rate 192Ir BT source. Detectors based on plastic scintillators BCF-12 and BCF-60 (0.8 mm3 volume) were used as a reference. Measurements demonstrated that the ruby, Y2O3:Eu+YVO4:Eu, ZnSe:O, and CsI:Tl ISDs emitted scintillation signals that were up to 19, 19, 250, and 880 times greater, respectively, than that of the BCF-12 detector. While the total signals of the plastic scintillation detectors were dominated by the stem signal for source positions 0.5 cm from the fiber-optic cable and >3.5 cm from the scintillator volume, the stem signal for the ruby and Y2O3:Eu+YVO4:Eu ISDs were <1% of the total signal for source positions <3.4 and <4.4 cm from the scintillator, respectively, and <0.7% and <0.5% for the ZnSe:O and CsI:Tl ISDs, respectively, for positions ⩽8.0 cm. In contrast to the other ISDs, the Y2O3:Eu+YVO4:Eu ISD exhibited unstable scintillation and significant afterglow. All ISDs exhibited significant energy dependence, i.e. their dose response to distance-dependent 192Ir energy spectra differed significantly from the absorbed dose in water. Provided that energy dependence is accounted for, ZnSe:O ISDs are promising for use in error detection and patient safety monitoring during BT.

Characterizing the Antimicrobial Properties of 405 nm Light and the Corning® Light-Diffusing Fiber Delivery System.

BACKGROUND AND OBJECTIVES: Hospital-acquired infections (HAIs) and multidrug resistant bacteria pose a significant threat to the U.S. healthcare system. With a dearth of new antibiotic approvals, novel antimicrobial strategies are required to help solve this problem. Violet-blue visible light (400-470 nm) has been shown to elicit strong antimicrobial effects toward many pathogens, including representatives of the ESKAPE bacterial pathogens, which have a high propensity to cause HAIs. However, phototherapeutic solutions to prevention or treating infections are currently limited by efficient and nonobtrusive light-delivery mechanisms. STUDY DESIGN/MATERIALS AND METHODS: Here, we investigate the in vitro antimicrobial properties of flexible Corning® light-diffusing fiber (LDF) toward members of the ESKAPE pathogens in a variety of growth states and in the context of biological materials. Bacteria were grown on agar surfaces, in liquid culture and on abiotic surfaces. We also explored the effects of 405 nm light within the presence of lung surfactant, human serum, and on eukaryotic cells. Pathogens tested include Enterococcus spp, Staphylococcus aureus, Klebsiella pneumoniae, Acinetobacter baumannii, Pseudomonas aeruginosa, Enterobacter spp., Staphylococcus epidermidis, Streptococcus pyogenes, Candida albicans, and Escherichia coli. RESULTS: Overall, the LDF delivery of 405 nm violet-blue light exerted a significant degree of microbicidal activity against a wide range of pathogens under diverse experimental conditions. CONCLUSIONS: The results exemplify the fiber's promise as a non-traditional approach for the prevention and/or therapeutic intervention of HAIs. Lasers Surg. Med. © 2019 The Authors. Lasers in Surgery and Medicine Published by Wiley Periodicals, Inc.

Single-molecule detection of biomarker and localized cellular photothermal therapy using an optical microfiber with nanointerface.

For early-stage diagnostics, there is a strong demand for sensors that can rapidly detect biomarkers at ultralow concentration or even at the single-molecule level. Compared with other types of sensors, optical microfibers are more convenient for use as point-of-care devices in early-stage diagnostics. However, the relatively low sensitivity strongly hinders their use. To this end, an optical microfiber is functionalized with a plasmonic nanointerface consisting of black phosphorus-supported Au nanohybrids. The microfiber is able to detect epidermal growth factor receptor (ErbB2) at concentrations ranging from 10 zM to 100 nM, with a detection limit of 6.72 zM, enabling detection at the single-molecule level. The nanointerface-sensitized microfiber is capable of differentiating cancer cells from normal cells and treating cancer cells through cellular photothermal therapy. This work opens up a possible approach for the integration of cellular diagnosis and treatment.