Measurement of middle ear transfer function in temporal bones using electromagnetic excitation: Comparison to sound excitation and evaluation of influencing factors.

Hearing a sound produces vibrations of the ossicles in the middle ear, which can be measured in the micrometer to nanometer range. Destruction of middle ear structures results most commonly from chronic inflammatory diseases. In these cases, passive and active middle ear implants are used for reconstruction of the ossicular chain. The positioning of the implants depends primarily on the surgeon's experience. So far, no objective assessment has been conducted to affirm if the chosen positioning is the best in each specific case. We have established a new method, allowing us to measure the middle ear transfer function (METF) intraoperatively. Using the new method, a magnet is placed on the umbo of the malleus handle and is stimulated by a coil positioned underneath the head. The resulting vibration is measured on the stapes footplate using Laser Doppler vibrometry (LDV). Acoustic and electromagnetic excitation show comparable METF in lower frequencies, which differ up to 10 dB in frequencies over 1 kHz. The position of the coil does not play a relevant part in the METF, whereas the location of the magnet on the tympanic membrane highly impacts the METF. This technique demonstrates reproducible results. Electromagnetic excitation is comparable to sound excitation and is suited for measuring the METF. A stable positioning of the magnet on the umbo is essential in order to acquire valid data.

[Laser Doppler vibrometric measurements on human temporal bones]. / Laser-Doppler-vibrometrische Messungen an humanen Felsenbeinen.

Laser Doppler vibrometric (LDV) measurements on human temporal bones represent the standard method for predicting the performance of active middle ear implants (AMEI) and are used as preclinical tests in the development, approval process, and indication expansion of AMEI. The quality of the coupling of the floating mass transducer to the mobile structures of the middle ear is decisive for the performance of the implant and patients' hearing perception. The cochlea can be stimulated via the oval window (forward stimulation) or the round window (reverse stimulation). For forward stimulation, the ASTM standard F2504-05 defines a method to ensure physiologically normal properties of the temporal bones used in the experiments. For reverse stimulation, which depends even more critically on the quality of the temporal bone, a comparable standard method is lacking. Appropriate preparation and storage of the human petrous bone as well as suitable LDV test setups with respect to calibration and reproducibility of measuring positions and angles provide results that allow a comparison of different types of coupling and also correlate well with clinical data.

Feasibility Study of a Mechanical Real-Time Feedback System for Optimizing the Sound Transfer in the Reconstructed Middle Ear.

OBJECTIVE: To evaluate electromechanical excitation as an alternative excitation mode for middle ear transfer function (METF) measurements as well as real-time feedback in prosthetic ossicular reconstruction. METHOD: In eight human cadaveric temporal bones, the ossicular chain was excited using acoustic and mechanical (floating mass transducer, FMT) stimulation to determine the METF. After disconnecting the ossicular chain and reconstruction with partial or total prosthesis the METFs were measured again. Continuous FMT stimulation was then applied to improve the prosthesis' position using real-time feedback of the METF. RESULTS: Mechanical stimulation of ossicular vibration showed characteristic differences to acoustic excitation resulting from the force characteristics of the FMT. Furthermore, the interspecimen METF variability was greater with electromechanical than acoustic stimulation because of interspecimen variability in the FMT coupling conditions. When the METF with FMT excitation was used as a real-time feedback tool, a measurable improvement in the quality of ossicular reconstruction could be achieved. CONCLUSIONS: Mechanical excitation is an effective and suitable alternative stimulation method in experimental METF measurements. The system provides real-time feedback for ossicular reconstruction in the experimental setting. Some influencing factors still need to be distinguished for reliable measurements. However, the method does not yet meet the requirements for clinical application as an intraoperative, real-time monitoring tool. However, the system could be an excellent model for high-end cadaveric temporal bone training in ossiculoplasty.

Bone Metabolic Markers in the Clinical Assessment of Patients with Superior Semicircular Canal Dehiscence.

BACKGROUND: Superior semicircular canal dehiscence (SSCD) is a bony defect in the osseous shell of the petrous temporal bone. The pathophysiological association between osteoporosis and SSCD remains poorly understood. We investigated the relationship between bone metabolic markers and symptoms in patients with SSCD. METHODS: We collected patient demographics and clinical parameters for adult patients diagnosed with SSCD on high-resolution computed tomography scans. We used point-biserial correlation analysis to investigate the relationship between bone metabolic markers and symptoms in patients with SSCD. We compared clinical symptoms before and after surgical repair of SSCD through a middle fossa craniotomy using McNemar's test for paired comparisons of binary measures. RESULTS: We included a total of 99 patients (64 females and 35 males; average age 52 years; 118 surgeries). The level of serum calcium correlated with the need for a second surgery (rpb = -0.35, P = 0.001). Postoperative calcium supplementation negatively correlated with improvement in dizziness (rpb = -0.36, P = 0.01). The level of 25-hydroxyvitamin D correlated with preoperative hyperacusis (rpb = -0.98, P = 0.02) and postoperative autophony (rpb = 0.96, P = 0.04). Postoperative vitamin D supplementation positively correlated with hearing decline (rpb = 0.04, P = 0.04) The level of thyroid stimulating hormone correlated with preoperative autophony, amplification, and tinnitus (rpb = -0.71, rpb = -0.75, rpb = -0.70, all P < 0.001). CONCLUSIONS: Bone metabolic markers could be important in the clinical assessment of SSCD patients and could be potential targets for symptom management.

The Predictability Precision of Superior Semicircular Canal Through Radiological Assessment and Microanatomical Dissection.

OBJECTIVE: There is still ongoing research on the relationship of arcuate eminence (AE) and superior semicircular canal (SSC). We aimed to evaluate the precision of predictability of SSC through the morphology of AE via radiological means. MATERIALS AND METHODS: This investigation is performed on 12 dry skulls belonging to Mersin University Medical Faculty department of anatomy. Computed tomography (CT) assessment is performed with 0.5-mm-thin sections temporal bone algorithm on dry skulls which were marked with fixated copper wire by scotch tapes on the most prominent part of the middle fossa floor assuming the location of AE. The data are reformatted on the workstation with vitrea 2.0. The distances of the determined three points including lateral (A), apical (B), and medial (C) of the SSC and the copper wire are measured radiologically. Also, the height between the most apical part of the SSC to the floor of the skullbase (H) is measured. The angles between the placed copper wires and the SSC (E) are calculated. The angle between SSC and the midpoint of the IAC (F) and SSC to the sulcus of the greater GSPN (G) were measured. The nearest distance was measured between the most posterior part of the SSC and the point marked by the perpendicular line drawn from the medial border of the petrous bone to the most posterior part of the internal auditory canal (IAC) (D). RESULTS: The right and left A, B, and C distances are 2.54+/- 2.75, 3.67+/-3.16, 5.85+/-3.77; 2.92+/-2.24, 3.68+/-2.93, 6.09+/-3.40, respectively. We could not find any statistical significance when the right A, B, and C distances were compared with the left values. Examination of the values revealed that C distance is greater than the A distance of the same side both for right (p=0.040) and left (p=0.022) measurements. The calculated left and right E angles are 30.313+/-12.838, and 35.558+/-18.437 degrees, respectively. Statistical significance was not found between the right and left angles. The right and left F, G angles were 53.17, 47.25; 93.58, 100.92 degrees; and D distances are 8.01, 8.13 millimeters, respectively. Statistical significance was not found when right and left E, F, G angles and D distances were compared. Among 12 left and 12 right sides, the copper wire was found to be nearly overlapping to SSC in two in the right and only one in the left. CONCLUSION: This study reveals that there is a great variability predicting the exact location of SSC through the prominence of AE. Complementary studies are needed with greater number of dry skulls and cadavers. Comparison of different hypothesis including the effect of temporal lobe sulcus is to be discussed to better enlighten the exact relationship of the aforementioned anatomical structures.

Surgical management of temporal bone osteoradionecrosis: Single surgeon experience of 47 cases.

PURPOSE: To report the outcomes of 47 patients with temporal bone osteoradionecrosis treated primarily with surgical resection in order to analyze whether flap type and hyperbaric oxygen use affect wound breakdown. MATERIALS AND METHODS: Between January 1998 and January 2016, 47 patients were treated for temporal bone osteoradionecrosis with surgery. Some patients were also treated with hyperbaric oxygen. Resection of grossly necrotic temporal bone was followed by immediate reconstruction with local, regional, or free flaps. Minimum follow-up was 6months. If patients had breakdown of their initial reconstructions, secondary reconstruction was performed with either a regional or free flap. During the post-operative period, wound breakdown, flap complications, and patient survival were noted. RESULTS: 30 patients developed ORN from primary radiotherapy while 17 had post-operative radiation. It was found that wound breakdown was significantly associated with type of flap reconstruction (p=0.02) with local flap reconstruction portending a poorer prognosis. Hyperbaric oxygen was not associated with decreased wound breakdown (p=0.5). CONCLUSIONS: Surgical treatment can be an effective treatment for temporal bone osteoradionecrosis, without hyperbaric oxygen providing any additional benefit. Reconstruction with regional or free flaps may be a more reliable method to resurface defects compared to local flaps.

A comparative study of MED-EL FMT attachment to the long process of the incus in intact middle ears and its attachment to disarticulated stapes head.

The Vibrant Soundbridge© (VSB) active middle-ear implant provides an effective treatment for mild-to-severe sensorineural hearing loss in the case of normal middle ear anatomy and mixed hearing loss in middle ear malformation. The VSB floating mass transducer (FMT), with proper couplers, can be installed on various structures of the ossicular chain, e.g., the short and long process of the incus, the stapes head, and the stapes footplate. A long process (LP) coupler is most commonly used for FMT attachment to the long process of the incus with intact ossicular chain, while CliP and Bell couplers are two standardized and reliable methods for FMT attachment to the stapes head with missing incus and malleus. However, the difference and relationship of the vibration properties among these three FMT couplers remain unclear. In the present study, the stapes footplate velocity responses of the LP, CliP, and Bell couplers have been investigated in eight fresh temporal bones (TBs) to evaluate the vibration properties of these three couplers. Normal and reconstructed middle ear transfer functions (METFs) were determined from laser Doppler vibrometer (LDV) measurements. A mastoidectomy and a posterior tympanotomy were performed to expose the ossicular chain. The METFs of the normal middle ear and middle ear with LP-FMT-coupler were compared under acoustic stimulation, thus the mass effect of the FMT with LP coupler was evaluated. Additional comparisons were made between the stapes footplate vibrations of the LP-FMT-coupler (with the intact ossicular chain at the long process of the incus), CliP-FMT-coupler and Bell-FMT-coupler on the stapes head (after incus and malleus removed) under active electromechanical stimulation. After the installation of CliP-FMT-coupler and Bell-FMT-coupler to the middle ear, the average velocity amplitude of the stapes footplate, comparing to the LP-FMT-coupler, was about 15 dB higher between 1 and 6 kHz, and 10 dB lower at about 0.5 kHz. Quantitatively, there was no significant difference between the CliP-FMT-coupler and Bell-FMT-coupler. According to our study, installation of CliP-FMT-coupler or Bell-FMT-coupler on the stapes head provides considerable improvement of the middle ear mechanical and functional responses, comparing with the LP-FMT-coupler in the temporal bone experiments. Moreover, the installation of the Bell-FMT-coupler to the stapes head produces essentially the same footplate velocity responses in comparison to the CliP-FMT-coupler.

New chamber stapes prosthesis - A preliminary assessment of the functioning of the prototype.

Piston-stapedotomy is the most common method for hearing restoration in patients with otosclerosis. In this study, we have experimentally examined a prototype of a new chamber stapes prosthesis. The prototype was implanted in a human cadaver temporal bone. The round window vibrations before and after implantation were measured for the acoustic signal (90 dB SPL, 0.8-8 kHz) in the external auditory canal. In comparison with a 0.4-mm piston prosthesis, the chamber prosthesis induced significantly higher vibration of the round window, especially for frequencies above 1.5 kHz. Based on the results, it can be surmised that stapedotomy with a chamber stapes prosthesis could provide better hearing results in comparison with the piston-stapedotomy.

The Effect of Piston Diameter in Stapedotomy for Otosclerosis: A Temporal Bone Model.

HYPOTHESIS: The use of larger-diameter pistons in stapedotomy leads to better hearing outcomes compared with the use of smaller-diameter pistons. There is an interaction between stapes piston diameter and fenestration diameter. BACKGROUND: Otosclerosis can be treated surgically by removing part of the stapes and bypassing the stapes footplate with a prosthesis. Available piston shaft diameters range between 0.3 and 0.8 mm. There has been a tendency toward the use of smaller-diameter pistons, because of a suspected decreased risk of cochlear trauma and subsequent sensorineural hearing loss (SNHL) with smaller pistons. However, mathematical models, temporal bone studies, and clinical studies suggest that the use of larger-diameter pistons is associated with better hearing outcomes. METHODS: Three fresh-frozen, non-pathologic temporal bones were harvested from human cadaveric donors. Acoustic stimuli in the form of pure tones from 250 to 8000 Hz were generated at 110 dB sound pressure level. A total of 16 frequencies in a 1/3-octave series were used. Stapes and round window velocities in response to the acoustic stimuli were measured at multiple equally spaced points covering the stapes footplate and round window using a scanning laser Doppler interferometry system. Eight sets of measurements were performed in each temporal bone: 1) normal condition (mobile stapes), 2) stapes fixation and stapedotomy followed by insertion of 3) a 0.4-mm-diameter piston in a 0.5-mm-diameter fenestration, 4) a 0.4-mm-diameter piston in a 0.7-mm-diameter fenestration, 5) a 0.4-mm-diameter piston in a 0.9-mm-diameter fenestration, 6) a 0.6-mm-diameter piston in a 0.7-mm-diameter fenestration, 7) a 0.6-mm-diameter piston in a 0.9-mm-diameter fenestration, and 8) a 0.8-mm-diameter piston in a 0.9-mm-diameter fenestration. RESULTS: At midrange frequencies, between 500 and 4000 Hz, round window velocities increased by 2 to 3 dB when using a 0.6-mm-diameter piston compared with a 0.4-mm-diameter piston. Using a 0.8-mm-diameter piston led to a further increase in round window velocities by 2 to 4 dB. CONCLUSION: Our results suggest a modest effect of piston diameter on hearing results following stapedotomy.

A tri-coil bellows-type round window transducer with improved frequency characteristics for middle-ear implants.

A number of methods to drive the round window (RW) using a floating mass transducer (FMT) have been reported. This method has attracted attention because the FMT is relatively easy to implant in the RW niche. However, the use of an FMT to drive the RW has been proven to produce low outputs at frequencies below approximately 1 kHz. In this study, a new tri-coil bellows-type transducer (TCBT), which has excellent low frequency output and is easy to implant, is proposed. To design the frequency characteristics of the TCBT, mechanical and electrical simulations were performed, and then a comparative analysis was conducted between a floating mass type transducer (like the FMT) and a fixed type transducer (like the TCBT). The features of the proposed TCBT are as follows. First, the TCBT's housing is fixed to the RW niche so that it does not vibrate. Second, the internal end of a tiny bellows is connected to a vibrating three-pole permanent magnet located within three field coils. Finally, the rim of the bellows bottom is attached to the end of the housing that hermetically encloses the three field coils. In this design, the only vibrating element is the bellows itself, which efficiently drives the RW membrane. To evaluate the characteristics of this newly developed TCBT, the transducer was installed in the RW niche of temporal bones and the velocity of the stapes was measured using a laser Doppler vibrometer. The experimental results indicate that the TCBT can produce 100, 111, and 129 dB SPL equivalent pressure outputs at below 1 kHz, 1-3 kHz, and above 3 kHz, respectively. Thus, the TCBT with one side coupled to the RW via a bellows will be easy to implant and offer better performance than an FMT.

Effect of Round Window Reinforcement on Hearing: A Temporal Bone Study With Clinical Implications for Surgical Reinforcement of the Round Window.

HYPOTHESIS: Round window reinforcement leads to conductive hearing loss. BACKGROUND: The round window is stiffened surgically as therapy for various conditions, including perilymphatic fistula and superior semicircular canal dehiscence. Round window reinforcement reduces symptoms in these patients. However, it also reduces fluid displacement in the cochlea and might therefore increase conductive hearing loss. METHODS: Perichondrium was applied to the round window membrane in nine fresh-frozen, nonpathologic temporal bones. In four temporal bones cartilage was applied subsequently. Acoustic stimuli in the form of frequency sweeps from 250 to 8000 Hz were generated at 110 dB sound pressure level. A total of 16 frequencies in a 1/3-octave series were used. Stapes velocities in response to the acoustic stimuli were measured at equally spaced multiple points covering the stapes footplate using a scanning laser Doppler interferometry system. Measurements were made at baseline, after applying perichondrium, and after applying cartilage. RESULTS: At frequencies up to 1000 Hz perichondrium reinforcement decreased stapes velocities by 1.5 to 2.9 dB compared with no reinforcement (p value = 0.003). Reinforcement with cartilage led to a further deterioration of stapes velocities by 2.6 to 4.2 dB at frequencies up to 1000 Hz (p value = 0.050). The higher frequencies were not affected by perichondrium reinforcement (p value = 0.774) or cartilage reinforcement (p value = 0.644). CONCLUSION: Our results seem to suggest a modest, clinically negligible effect of reinforcement with perichondrium. Placing cartilage on the round window resulted in a graded effect on stapes velocities in keeping with the increased stiffness of cartilage compared with perichondrium. Even so, the effect was relatively small.

Intraoperative assessment of ossicular fixation.

Determining the degree of ossicular fixation is a difficult task, with the final assessment often being made with manual palpation during exploratory tympanotomy. A more objective method to evaluate ossicular fixation would be valuable. In this paper we describe a new method which makes use of a magnet and coil to measure ossicular motion through the ear canal with an elevated tympanic membrane. We report measurements of the vibration response at the umbo, the tip of the incus long process and the lateral posterior crus of the stapes before and after artificially fixing the stapes footplate and anterior mallear ligament with luting cement. Results were obtained on temporal bones, but the practicality of the method allows easy clinical implementation. Velocity ratios between different measurement points along the ossicular chain may provide a quantitative indication of the degree of stapes fixation. Isolated anterior mallear ligament fixation was not distinguishable from the unfixed condition.

First results of a novel adjustable-length ossicular reconstruction prosthesis in temporal bones.

OBJECTIVES/HYPOTHESIS: The performance of an ossicular replacement prosthesis (ORP) is influenced by its alignment and appropriate tension between the tympanic membrane and the stapes footplate. A novel ORP with a flexible element that potentially allows for length adjustment in situ is presented and tested for acoustic performance. STUDY DESIGN: Laser Doppler vibrometry in fresh human cadaveric temporal bones was used to test the acoustic performance of the adjustable ORP relative to standard prostheses used for ossiculoplasty. METHODS: The three-dimensional (3D) velocity of the stapes posterior crus was measured in the 0.2- to 20-kHz range using a Polytec CLV-3D laser Doppler vibrometer. The middle ear cavity was accessed through a facial recess approach. After measuring the normal response, the incus was removed and stapes velocity was measured in the disarticulated case, then after insertion of the new prosthesis, a conventional prosthesis (Kurz BELL Dusseldorf type), and a sculpted autologous incus prosthesis in each temporal bone. The 3D stapes velocity transfer function (SVTF) was calculated for each case and compared. RESULTS: The novel ORP design restored stapes velocity to within 6 dB (on average) of the intact response. No significant differences in 3D-SVTF were found between the new, conventional, or autologous ORPs. CONCLUSIONS: The inclusion of an in situ adjustable element into the ORP design did not adversely affect its acoustic performance. The adjustable element may increase the ease of achieving optimal ORP placement, especially through a facial recess approach. LEVEL OF EVIDENCE: NA Laryngoscope, 126:2559-2564, 2016.

Electro-Mechanical Stimulation of the Cochlea by Vibrating Cochlear Implant Electrodes.

INTRODUCTION: Electro-acoustic stimulation (EAS) of the cochlea uses the preserved residual low-frequency hearing for acoustic stimulation in combination with electrical stimulation. The acoustic low-frequency component is amplified and high-frequency hearing is enhanced by a cochlear implant (CI). In this work, the feasibility of EAS by the floating mass transducers (FMTs) firmly attached to the implanted electrode was investigated and the achieved stapes displacement was compared with sound stimulation. METHODS: Experiments were performed in eight fresh human temporal bones compliant to the ASTM standard (F2504-5). Four EAS custom-made prototypes (EAS-CMP) were tested, consisting of standard MED-EL CI electrodes with Vibrant Soundbridge (VSB) FMTs or a Bonebridge (BB) FMT tightly molded to the electrode in different orientations. The stapes footplate (SFP) response to EAS-CMP stimulation and sound stimulation was measured using a Laser Doppler Vibrometer (LDV). RESULTS: The SFP displacement amplitudes achieved by EAS-CMP stimulation were calculated to 1 VRMS FMT input and were pair-wise statistically compared between prototypes yielding no significant differences at frequencies ≤1 kHz. At frequencies ≤1 kHz stimulation by the BB FMT resulted in a flat and potentially highest SFP displacement amplitude of approximately -40 dB re µm at 1 VRMS input voltage. Estimated equivalent sound pressure levels achieved by the BB FMT prototype were approximately 83-90 eq. dB SPL at frequencies ≤1 kHz. CONCLUSION: The feasibility of cochlear stimulation by vibrating electrodes was shown although the achieved output level at frequencies ≤1 kHz was too low for EAS applications.

Towards quantitative diagnosis of ossicular fixation: Measurement of stapes fixations using magnetically driven ossicles in human temporal bones.

CONCLUSION: Information on the degree of stapes fixation can be found by measuring the ratio of stapes to umbo and stapes to incus velocity. OBJECTIVES: To evaluate a method of quantifying ossicular fixation in an ear with elevated tympanic membrane. METHOD: Measurements were made on four fresh-frozen human temporal bones. After elevating the tympanic membrane, a small magnet was attached to the manubrium and an electromagnetic excitation coil was used to vibrate the ossicles. The vibration response of the umbo, the tip of the incus long process, and the posterior crus of the stapes were measured before and after partially fixing the footplate with luting cement. RESULTS: The velocities at the different measurement points were unequally affected by the fixation. The difference in the velocity ratio between different points provides an indication of the degree of footplate fixation.

Vibro-EAS: a proposal for electroacoustic stimulation.

HYPOTHESIS: In situ evaluation of the vibration performance of a hybrid system for intracochlear fluid stimulation, constructed from a floating mass transducer (FMT) coupled to an electric acoustic stimulation (EAS) cochlea implant (CI) electrode. BACKGROUND: EAS uses both CI technology to restore severe-to-profound hearing loss at high frequencies and acoustic amplification for mild-to-moderate hearing loss in the low-to-mid frequency range. More patients with residual hearing are becoming candidates for EAS surgery because of the improved techniques for hearing preservation. Most patients with partial deafness fulfill the audiological criteria at low and mid-frequencies for the active middle-ear implant with FMT (VSB). The FMT of the VSB is a potential device for acoustical stimulation in EAS. METHODS: In seven fresh human temporal bones, stapes amplitude responses for fixation of a FMT to the long incus process (standard coupling) was compared with those for FMT fixation to a 20-mm inserted standard cochlea electrode array (31.5 mm) via the round window (Vibro-EAS). Vibration of the stapes footplate was measured by laser Doppler vibrometry. RESULTS: For 0.316 Vrms drive voltage, stimulation of the intracochlear fluid using a FMT-driven CI electrode (Vibro-EAS) yielded stapes amplitude responses comparable to those for acoustic stimulation with 84 dB SPL. These amplitude responses are 30 to 42 dB lower at frequencies up to 4 kHz than those for VSB standard coupling. CONCLUSION: Intracochlear combined electrical and mechanical stimulation may be a viable technique for electroacoustic stimulation. A reliable technique for attachment or integration of the FMT to the cochlea electrode array has yet to be developed.

Osteoradionecrosis of the temporal bone: a case series.

OBJECTIVE: To study osteoradionecrosis (ORN) of the temporal bone. STUDY DESIGN: Retrospective case review. SETTING: Academic medical center. PATIENTS: Patients were included who had previously undergone radiation to the head and neck and then developed exposed necrotic bone within the ear canal that persisted at least 3 months. INTERVENTIONS: Patients were treated with a variety of modalities, including conservative therapy with antibiotic ear drops and in-office debridements, hyperbaric oxygen therapy, and surgery. MAIN OUTCOME MEASURES: To describe the presentation and management of patients with temporal bone osteoradionecrosis. RESULTS: Thirty-three patients with temporal bone osteoradionecrosis were included. The most common site of primary tumor was the parotid gland (n = 11), followed by the nasopharynx (n = 7). The time to development of ORN varied between 1 and 22 years, with mean of 7.9 years. The mean radiation dose was 62.6 Gy to the primary tumor, 53.1 Gy to the affected temporal bone, and 65.2 Gy to the affected tympanic bone. The most common symptoms of ORN were otorrhea (n = 15), hearing loss (n = 13), and otalgia (n = 12). Fifteen patients had bacterial superinfection, most commonly Staphylococcus aureus (n = 9). Conservative therapy was successful at managing symptoms but not in eradicating exposed bone in most patients. Surgery was used for recalcitrant pain, infection, cholesteatoma, cranial neuropathies, and intracranial complications. CONCLUSION: Osteoradionecrosis is a rare complication of radiation to the temporal bone. Management should be aimed at relief of symptoms, eradication of superinfection, and treatment of other commonly present radiation effects like cholesteatoma and hearing loss.

Alternative fixation of an active middle ear implant at the short incus process.

INTRODUCTION: Since 1996, the preferred approach for positioning the active middle-ear implant Vibrant Soundbridge© is a mastoidectomy and a posterior tympanotomy. With this device, placement of the floating mass transducer (FMT) on the long incus process is the standard method for treatment of mild-to-severe sensorineural hearing loss in the case of normal middle-ear anatomy. The aim of this study was to determine the vibrational effectiveness of FMT placement at the short incus process. MATERIALS AND METHODS: An extended antrotomy and a posterior tympanotomy were performed in 5 fresh human temporal bones. As a control for normal middle-ear function, the tympanic membrane was stimulated acoustically and the vibration of the stapes footplate and the round-window (RW) membrane were (sequentially) measured by laser Doppler vibrometry. Vibration responses for coupling of an FMT to the long incus process (standard coupling) were compared to those for coupling to the short incus process. RESULTS: Apart from narrow frequency bands near 3 and 9 kHz for the stapes footplate and RW membrane, respectively, the velocity responses presented no significant differences between standard coupling of the FMT and coupling to the short incus process. CONCLUSION: Coupling the FMT to the short incus process may be a viable alternative in cases where the surgical approach is limited to an extended antrotomy. A reliable technique for attachment to the short incus process has yet to be developed.

Vibromechanical assessment of active middle ear implant stimulation in simulated middle ear effusion: a temporal bone study.

HYPOTHESIS: Active middle ear implant (AMEI) generated vibromechanical stimulation of the ossicular chain (ossicular chain vibroplasty [OCV]) or the round window (round window vibroplasty [RWV]) is not significantly affected by simulated middle ear effusion in a human temporal bone model. BACKGROUND: OCV and RWV may be employed for sensorineural, mixed, and conductive hearing losses. Although middle ear effusions may be encountered across patient populations, little is known about how effusions may affect AMEI vibromechanical efficiency. METHODS: Laser Doppler vibrometry of stapes velocities (SVs) were performed in a human temporal bone model of simulated effusion (N = 5). Baseline measurements to acoustic sinusoidal stimuli, OCV, and RWV (0.25-8 kHz) were made without effusion. The measurements were repeated with simulated middle ear effusion and compared with baseline measurements. Data were analyzed across 3 frequency bands: low (0.25-1 kHz), medium (1-3 kHz), and high (3-8 kHz). RESULTS: Acoustic stimulation with simulated middle ear effusion resulted in a significant (p < 0.001) frequency-dependent attenuation of SVs of 4, 10, and 7 dB (low, medium, and high ranges, respectively). OCV in simulated effusion resulted in attenuated SVs of 1, 5, and 14 dB (low, medium, and high) compared to without effusion; however, this attenuation was not significant (p = 0.07). Interestingly, in the setting of RWV, simulated effusion resulted in significantly (p = 0.001) increased SVs of 16, 11, and 8 dB (low, medium, and high). A 3-dB variance in AMEI efficiency was observed in repeated measurements in a single temporal bone. CONCLUSION: The efficiency of OCV was not significantly affected by the presence of a middle ear effusion. Improved efficiency, however, was observed with RWV.

Results of Baha® implantation using a small horizontal incision.

PURPOSE: Techniques for Baha® implantation continue to evolve. The Weber technique, utilizing a 1.5 cm horizontal incision for Baha® implantation is evaluated. METHODS: Retrospective review of patients undergoing Baha® implantation by a single surgeon over three years. RESULTS: 33 Baha®s implanted in 30 patients. Fourteen used an Inverted J (IJ) incision with an anteriorly-based skin-flap, 13 with the Weber technique (W). Five were not included as other techniques were used. Demographics and weeks to activation (14.58 vs 13.4, p = 0.12) were similar. There were no differences in the number of patients with minor complications (5 vs 2, p = 0.22) or number of minor complications (20 vs 4, p = 0.09). One patient in the IJ Group required operative revision for overgrowth. There were no infections in the IJ Group, and one requiring oral antibiotics in the W Group. Follow-up was longer in the IJ Group (41 vs 13 weeks, p = 0.016), no complications occurred after 14 weeks post-op. Mean operative times were similar (43 vs 39 min, p = 0.59). There were no cases of skin flap necrosis in either group. CONCLUSION: A small incision for Baha® implantation proved as effective, without increased complications as a skin-flap based technique.