Assessment of the water quality and toxicity effects on zebrafish (Danio rerio) of a stream near a phosphorus chemical plant in Guizhou Province, southwestern China.

To reveal the influence of the phosphorus chemical industry (PCI) on regional water environmental quality and safety, the water quality and ecotoxicological effects of a stream near a phosphorus chemical plant (PCP) in Guizhou Province, southwestern China, were investigated based on water samples collected from the stream. The results showed that the average concentrations of NH3-N, TN, P, F-, Hg, Mn, and Ni were 3.14 mg/L, 30.09 mg/L, 3.34 mg/L, 1.18 mg/L, 1.06 µg/L, 45.82 µg/L, and 11.30 µg/L, respectively. The overall water quality of the stream was in the heavily polluted category, and NH3-N, TN, P, F-, and Hg were the main pollution factors. The degree of pollution was in the order of rainy period > transitional period > dry period, and the most polluted sample site was 1100 m from the PCP. After 28 days of exposure to stream water, there was no significant change in the growth parameters of zebrafish. The gills of zebrafish showed a small amount of epithelial cell detachment and a small amount of inflammatory cell infiltration, and the liver tissue displayed a large amount of hepatocyte degeneration with loose and lightly stained cytoplasm. Compared with the control group, the %DNA in tail, tail length, tail moment, and olive tail moment were significantly increased (p < 0.05), indicating that the water sample caused DNA damage in the peripheral blood erythrocytes of zebrafish. The stream water in the PCI area was found to be polluted and exhibited significant toxicity to zebrafish, which could pose a threat to regional ecological security.

Impact of Ergonomic Posture on the Chemical Exposure of Workers in the Petroleum and Chemical Industry.

OBJECTIVES: Despite a rise in automation, workers in the petroleum refining and petrochemical manufacturing industry are potentially exposed to various chemicals through inhalation while performing routine job duties. Many factors contribute to the degree of exposure experienced in this setting. The study objective was to characterize the impact of workplace conditions, anthropometric variability, and task orientation on exposure for a simulated routine operations task. METHODS: A chemical exposure laboratory simulation study was designed to evaluate the dependent variable of chemical exposure level in the breathing zone for methane and sulfur hexafluoride. The independent variables were (i) posture of the worker, (ii) worker anthropometry, (iii) process configuration, and (iv) gas density. RESULTS: Pipe height was a significant predictor of gas concentration measured in the breathing zone when located in a position that encouraged the gas to enter the breathing zone of the worker. Worker anthropometry had a major impact; tall worker's (male) chemical concentrations exceeded those of the short worker (female) for methane simulations but the opposite resulted for sulfur hexafluoride. Also, worker posture had a significant impact on gas exposure where nonneutral postures were found to have higher levels of chemical concentration. CONCLUSIONS: The study findings indicate that the breathing zone location is altered by posture and worker height, which changes the exposures relative to the emission source depending on the gas density of the chemicals that are present. As a result, qualitative risk assessment cannot be performed accurately without accounting for these factors. Practically, controls may need to account for worker size differences and posture adaptations.

High-throughput 16S rRNA gene sequencing of the microbial community associated with palm oil mill effluents of two oil processing systems.

Palm Oil Mill Effluents (POME) are complex fermentative substrates which habour diverse native microbial contaminants. However, knowledge on the microbiota community shift caused by the anthropogenic effects of POME in the environment is up to date still to be extensively documented. In this study, the bacterial and archaeal communities of POME from two palm oil processing systems (artisanal and industrial) were investigated by Illumina MiSeq Platform. Despite the common characteristics of these wastewaters, we found that their microbial communities were significantly different with regard to their diversity and relative abundance of their different Amplicon Sequence Variants (ASV). Indeed, POME from industrial plants harboured as dominant phyla Firmicutes (46.24%), Bacteroidetes (34.19%), Proteobacteria (15.11%), with the particular presence of Spirochaetes, verrucomicrobia and Synergistetes, while those from artisanal production were colonized by Firmicutes (92.06%), Proteobacteria (4.21%) and Actinobacteria (2.09%). Furthermore, 43 AVSs of archaea were detected only in POME from industrial plants and assigned to Crenarchaeota, Diapherotrites, Euryarchaeota and Nanoarchaeaeota phyla, populated mainly by many methane-forming archaea. Definitively, the microbial community composition of POME from both type of processing was markedly different, showing that the history of these ecosystems and various processing conditions have a great impact on each microbial community structure and diversity. By improving knowledge about this microbiome, the results also provide insight into the potential microbial contaminants of soils and rivers receiving these wastewaters.

A cross-industry collaboration to assess if acute oral toxicity (Q)SAR models are fit-for-purpose for GHS classification and labelling.

This study assesses whether currently available acute oral toxicity (AOT) in silico models, provided by the widely employed Leadscope software, are fit-for-purpose for categorization and labelling of chemicals. As part of this study, a large data set of proprietary and marketed compounds from multiple companies (pharmaceutical, plant protection products, and other chemical industries) was assembled to assess the models' performance. The absolute percentage of correct or more conservative predictions, based on a comparison of experimental and predicted GHS categories, was approximately 95%, after excluding a small percentage of inconclusive (indeterminate or out of domain) predictions. Since the frequency distribution across the experimental categories is skewed towards low toxicity chemicals, a balanced assessment was also performed. Across all compounds which could be assigned to a well-defined experimental category, the average percentage of correct or more conservative predictions was around 80%. These results indicate the potential for reliable and broad application of these models across different industrial sectors. This manuscript describes the evaluation of these models, highlights the importance of an expert review, and provides guidance on the use of AOT models to fulfill testing requirements, GHS classification/labelling, and transportation needs.

Radiological and physico-chemical characterization of materials from phosphoric acid production plant to assess the workers radiological risks.

The industry devoted to the production of phosphoric acid by using as raw material sedimentary phosphate rock (PR) is considered as a NORM activity (Naturally Occurring Radioactive Materials), due to the high levels of U-series radionuclides contained in this ore, which are 1-2 orders of magnitude higher than those in unperturbed soils. This fact allowed us to develop a deep characterization of the raw materials, wastes, main intermediate materials, and final products obtained at a typical phosphoric acid factory. The elemental composition (major, minor and trace elements), radionuclide concentrations, grain size distribution, mineralogy and micro-structural composition were analyzed. The aim of this characterization was to obtain information for operators and maintenance personnel involved in clean-up and waste management operations. The highest concentrations of some heavy metals and radionuclide activity concentrations were found in the "scales" (or internal incrustations)from the pipes that carry either phosphoric acid (PA) or the phosphogypsum waste (PG). The highest concentrations where found for 226Ra and 40K,with values up to 9 and 5 Bq g-1, respectively. In addition, high concentrations of many toxic heavy metals and trace elements, such as Cd, Cr, Ni, Sr, Y, V, Zn, Th, and U, were found in some sludge samples. The shielding effect of the containers/vessels/pipes has an essential role in the measured external dose in the intermediate products. The radiological implications of natural radionuclides with higher activity showed that if the maximum particulate matter concentration established in the Spanish regulation is verified, and taking into account the most conservative scenario, the annual limit of 1 mSv y-1 is not exceeded.

Residential exposure to petrochemical industrial complexes and the risk of leukemia: A systematic review and exposure-response meta-analysis.

Exposure to chemicals produced by petrochemical industrial complexes (PICs), such as benzene, ionizing radiation, and particulate matters, may contribute to the development of leukemia. However, epidemiological studies showed controversial results. This systematic review and meta-analysis aimed to summarize the association between residential exposure to PICs and the risk of leukemia incidence, focusing on exposure-response effects. We searched PubMed, Embase, Web of Science, and Cochrane Library databases for studies published before September 1st, 2019. Observational studies investigating residential exposure to PICs and the risk of leukemia were included. The outcome of interest was the incidence of leukemia comparing to reference groups. Relative risk (RR) was used as the summary effect measure, synthesized by characteristics of populations, distance to PICs, and calendar time in meta-regression. We identified 7 observational studies, including 2322 leukemia cases and substantial reference groups, in this meta-analysis. Residential exposure to PICs within a maximal 8-km distance had a 36% increased risk of leukemia (pooled RR = 1.36, 95% CI = 1.14-1.62) compared to controls, regardless of sex and age. In terms of leukemia subtypes, residential exposure to PICs was associated with the risks of acute myeloid leukemia (AML, pooled RR = 1.61, 95% CI = 1.12-2.31) and chronic lymphocytic leukemia (CLL, pooled RR = 1.85, 95% CI = 1.11-6.42). In meta-regression, the positive association occurred after 10 years of follow-up with a pooled RRs of 1.21 (95% CI = 1.02-1.44) and then slightly increased to 1.77 (95% CI = 1.35-2.33) at 30 years after follow-up. No effect modification was found by sex, age, and geographic locations.

Bio-electrochemical power generation in petrochemical wastewater fed microbial fuel cell.

The petrochemical wastewater (PCW) from acrylic acid plants possesses a very high chemical oxygen demand (COD) due to the presence of acrylic acid along with other organic acids. The treatment of PCW by conventional aerobic and anaerobic methods is energy intensive. Therefore, the treatment of PCW with concurrent power generation by employing microbial fuel cell (MFC) could be a potential alternative to solve the energy and environmental issues. This study demonstrates the potentiality of PCW from acrylic acid plant with an initial COD of 45,000 mg L-1 generating maximum power density of 850 mW m-2 at a current density of 1500 mA m-2 using acclimatized anaerobic sludge (AS) as biocatalyst. The predominant microbes present in acclimatized AS were identified using Biolog GEN III analysis, which include the electrogenic genera namely Pseudomonas spp. and Bacillus spp. along with methanogenic archea Methanobacterium spp. The mechanism of electron transfer was elucidated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) which clearly demonstrated the natural metabolite-based electron transfer across the electrode/biofilm/solution interface. The abundance of the electron shuttle metabolites was increased with the microbial growth in the bulk solution as well as in the biofilm leading to a high power generation. The COD removal efficiency and the coulombic efficiency (CE) were found to be 40% and 21%, respectively after 11 days of operation using initial COD of 45,000 mg L-1. The low COD removal efficiency could drastically be increased to 82% when the initial COD of PCW was 5000 mg L-1 generating a power density of 150 mW m-2. The current work proves the feasibility of the MFC for the treatment of acrylic acid plant PCW using acclimatized anaerobic sludge (AS) as a biocatalyst.

Treatment of chlorpyrifos manufacturing wastewater by peroxide promoted-catalytic wet air oxidation, struvite precipitation, and biological aerated biofilter.

Chlorpyrifos manufacturing wastewater (CMW) is characterized by complex composition, high chemical oxygen demand (COD) concentration, and toxicity. An integrated process comprising of peroxide (H2O2) promoted-catalytic wet air oxidation (PP-CWAO), struvite precipitation, and biological aerated filters (BAF) was constructed to treat CMW at a starting COD of 34000-35000 mg/L, total phosphorus (TP) of 5550-5620 mg/L, and total organophosphorus (TOP) of 4700-4840 mg/L. Firstly, PP-CWAO was used to decompose high concentrations of organic components and convert concentrated and recalcitrant TOP to inorganic phosphate. Copper citrate and ferrous citrate were used as the catalysts of PP-CWAO. Under the optimized conditions, 100% TOP was converted to inorganic phosphate with 95.6% COD removal. Then, the PP-CWAO effluent was subjected to struvite precipitation process for recovering phosphorus. At a molar ratio of Mg2+:NH4+:PO43- = 1.1:1.0:1.0, phosphate removal and recovery reached 97.2%. The effluent of struvite precipitation was further treated by the BAF system. Total removals of 99.0%, 95.2%, 97.3%, 100%, and 98.3% were obtained for COD, total suspended solids, TP, TOP, and chroma, respectively. This hybrid process has proved to be an efficient approach for organophosphate pesticide wastewater treatment and phosphorus reclamation.

Dissipation Behavior of Three Fungicides during the Industrial Processing of PaeoniaeRadix Alba and Associated Processing Factors.

Before being administered as medicinal products, Chinese herbal medicines (CHMs) must be processed and decocted for human consumption. While the presence of pesticide residues in CHMs is a major concern, pesticide dissipation behavior during CHM processing has rarely been reported. In this study, the dissipation of three pesticide residues in the CHM Paeoniae Radix Alba (PRA) was investigated during each step of industrial processing. The boiling process was found to significantly reduce pesticide residues (61-89%), and the peeling process also contributed to pesticide degradation (29-68%). The high temperature (60 °C) during the drying process led to further pesticide degradation. The processing factors of all three pesticides after each processing step were less than one, and the processing factors for the overall process were lower than 0.027, indicating that industrial processing clearly reduced the amount of pesticide residues (97.3-99.4%). The findings provide guidance for the safe use of fungicides in CHMs and can help establish maximum residue limits for PRA to reduce human exposure to pesticides.

A Robust Strategy for Sustainable Organic Chemicals Utilizing Bioprivileged Molecules.

Biobased chemicals will inevitably be an important part of a sustainable organic chemical industry. Current efforts in biobased chemicals are largely driven by opportunistic chemical product targets requiring complete technology development from feedstock to final product for a specific molecule. To enhance the development of biobased chemicals, it is important to create strategies that can be more systematic and can leverage advancements across multiple final products. Discussed here is the concept of bioprivileged molecules, which are chemical intermediates that have the potential to be efficiently converted into a range of product molecules that can both directly replace existing petrochemicals and are novel molecules that impart enhanced performance properties in end-use applications.

Electrooxidation Using Nb/BDD as Post-Treatment of a Reverse Osmosis Concentrate in the Petrochemical Industry.

This work evaluated the performance of an electrochemical oxidation process (EOP), using boron-doped diamond on niobium substrate (Nb/BDD), for the treatment of a reverse osmosis concentrate (ROC) produced from a petrochemical wastewater. The effects of applied current density (5, 10, or 20 mA·cm-2) and oxidation time (0 to 5 h) were evaluated following changes in chemical oxygen demand (COD) and total organic carbon (TOC). Current efficiency and specific energy consumption were also evaluated. Besides, the organic byproducts generated by EOP were analyzed by gas chromatography coupled to mass spectrometry (GC⁻MS). The results show that current densities and oxidation time lead to a COD and TOC reduction. For the 20 mA·cm-2, changes in the kinetic regime were found at 3 h and associated to the oxidation of inorganic ions by chlorinated species. After 3 h, the oxidants act in the organic oxidation, leading to a TOC removal of 71%. Although, due to the evolution of parallel reactions (O2, H2O2, and O3), the specific energy consumption also increased, the resulting consumption value of 66.5 kW·h·kg-1 of COD is considered a low energy requirement representing lower treatment costs. These results encourage the applicability of EOP equipped with Nb/BDD as a treatment process for the ROC.

Effect of a posture correction-based intervention on musculoskeletal symptoms and fatigue among control room operators.

This study was conducted to examine the effect of a posture correction-based intervention (with a biofeedback device) on the occurrence of musculoskeletal symptoms (MSS) and fatigue among control room operators in a petrochemical plant in Iran. A total of 188 office workers (91 in the case group and 97 in the control group) participated at baseline as well as at 6- and 12-month follow-up. A questionnaire survey (including the Nordic Musculoskeletal Questionnaire and Multidimensional Fatigue Inventory) and direct observations of working postures by using the Rapid Upper Limb Assessment (RULA) method were used. The occurrence of MSS in the shoulders, upper back, neck, and low back areas, as well as the mental and physical dimensions of fatigue were found to be the most common problems. The results showed considerable improvements in working postures (in the neck, trunk, and RULA grand scores) and the occurrence of MSS (particularly in the neck, shoulders, and upper back and low back areas) and fatigue (in particular the mental and physical aspects) after the intervention. The overall mean RULA grand score for the case group was significantly decreased after the intervention (mean scores of 5.1, 4.4, and 4.6 at pre-intervention, post-intervention 1, and post-intervention 2, respectively). A total of 81 operators (89.0%) reported some kind of MSS at baseline, which were reduced to 75 operators (82.4%) and 77 operators (84.6%) at post-interventions 1 and 2, respectively. Significant differences were also found between the pre- and post-intervention scores for the physical fatigue (mean of 12.19, 10.16, and 9.99 at pre-intervention, post-intervention 1, and post-intervention 2, respectively) and mental fatigue (mean of 14.03, 12.05, and 12.16 at pre-intervention, post-intervention 1, and post-intervention 2, respectively) dimensions. The findings confirm the effectiveness of this low-cost, simple, and easy-to-use ergonomic intervention.

Vertical distribution of fluorine in farmland soil profiles around phosphorous chemical industry factories.

High concentration of fluorine (F) in agricultural soils has got significant attention considering its impacts on human health, but little information was available about F distribution in farmland soil profiles around phosphorous chemical industry factories. In present study, farmland soil profiles and relevant medium samples were collected from farmlands around a main phosphorous chemical base in southwest China. At 0-100-cm profiles, concentrations of soil total F (Ft, 400.9-1612.0 mg kg-1) and water soluble F (Fw, 3.4-26.0 mg kg-1) decreased with profile depth in industrial areas. Industrial activities enhanced F concentration in soil mainly at 0-40-cm profiles. No disparity for both Ft and Fw distributions in paddy-dry land rotation field and dry land indicates short-term land utilization could not affect the F distribution in soil profiles. Correlation analysis showed soil organic matter and wind direction were important factors influencing the distribution of F in soil profiles. The shutdown of factory and government control of industrial emissions effectively decreased the ambient air F (Fa) concentrations in industrial areas. In where Fa and dustfall F concentrations were high, high soil Ft, Fw, and crop edible part F concentrations were found.

[Using of specialized food for the workers with skin occupational eczema of perlite production].

The research was conducted with participation of the perlite production workers with professional eczema (165 people in the main group and 152 from the control group without skin pathology). The effectiveness of the use of a specialized prophylactic food in the diet of workers was assessed on the basis of the study of the dynamics of the indicators of nutritional and clinical status. Inclusion of kissel, containing pectin, vitamin A (300% from RDA), vitamin E and zinc (40% from RDA), biologically active substances of plant origin in the diet of the examined against the background of the course of complex therapy, has resulted in a positive influence on individual laboratory values, demonstrating the optimization of metabolic processes, which characterize the pathogenesis of skin inflammation. Thus, the concentration of ascorbic acid in blood serum statistically significant (p<0.05) increased by 30.0%, tocopherol - by 36.3%, carotenoids - by 27.3%, phosphorus - by 28.9%, calcium level elevated by 16.3% (p<0.10). There was a decrease in the level of MDA in blood serum by 12.3% (p<0.05) and an increase in catalase activity by 12.2% (p>0.05). There was a tendency to reduce itching, infiltration, erythematous and eczematous manifestations of the disease. The data obtained make it possible to consider the use of a specialized food product of dietary preventive nutrition by workers in pearlite production as a mean to enhance the body's adaptive reserves and to prevent the occurrence, progression and development of occupational skin diseases (eczema) in the workplace.

Dynamics of phosphorus content and the activity of phosphatase in forest soil in the sustained nitrogen compounds emissions zone.

This paper summarizes research work on the seasonal and profile dynamics of phosphorus content and the activity of phosphatase in soil next to the nitrogen industry. The results are presented of the total phosphorus (TP) and available phosphorus (AP) content and the alkaline phosphatase (AlP) and acid phosphatase (AcP) against the basic physicochemical properties (clay, pH, total organic carbon, total nitrogen). Three soil profiles were sampled from Brunic Arenosols 0.8, 2.0, and 2.5 km away from the nitrogen plant. The control profile was taken from the Tuchola Forest. The soil was collected in both spring and autumn. The results showed that the total phosphorus content was higher in spring than in autumn (the value of index of changes in time TI < 0) contrary to available phosphorus (TI > 0) and in both seasons in surface soils, the lowest, in profile I. Both total and available phosphorus decreased with depth along the soil profiles. The distribution index (DI) calculated for total phosphorus in surface soils demonstrated a rather moderate accumulation, while DI value for available phosphorus for profile III, a considerable accumulation. The availability factor (AF) for all the soil samples was above the threshold of phosphorus load (2%) in the two seasons in this study (from 2.00 to 10.13% for spring and from 3.92 to 21.19% for autumn), suggesting that the transformation rate from TP to AP was high, and AP supply for plant growth was sufficient. The correlation analysis showed a significant and positive correlation of available phosphorus with soil properties such as total organic carbon (r = 0.577), total nitrogen (r = 0.512), and clay (r = 0.493); however, there was no correlation with the activity of phosphatases.

Risk assessment for potentially toxic metal(loid)s in potatoes in the indigenous zinc smelting area of northwestern Guizhou Province, China.

We investigated potentially toxic metal (loid)s (arsenic, As; cadmium, Cd; chromium, Cr; copper, Cu; mercury, Hg; lead, Pb; selenium, Se; and zinc, Zn) in agricultural samples (i.e., Solanum tuberosum L. tubers (potatoes) and their planting media) in the indigenous zinc smelting area of northwestern Guizhou Province, China. Based on the pollution index values for As, Cd, Pb and Zn, the order of the samples was as follow: slag > planting soil with slag > planting soil without slag, and the order of the samples in terms of the bioconcentration factor was the opposite. Cr, Cu and Hg were present in the planting soil with and without slag at slight pollution levels, and the other potentially toxic metal (loid)s had different degrees of contamination. Additionally, the potentially toxic metal (loid) contents in potato were under their limit values except for Cd (all samples) and Pb and Se (some samples). All bioconcentration factors for potatoes were below 0.5, and no health risk index value for potatoes was higher than 0.1. Therefore, although no significant health risk associated with potentially toxic metal (loid)s via consuming potato exists for either adult men or women in the research area, the Cd concentration in this crop should be monitored.

[Effects of occupational stress factors on the function of thyroid and liver among petroleum refining and petrochemical workers].

Objective: To investigate the association between occupational stress factors and the level of thyroid function and liver function in petroleum refining and petrochemical workers. Methods: A total of 353 petroleum refining workers were investigated by occupational stress indicator question-naire (OSI-R) , and their level of thyroid and liver function were measured. Results: With the incre-ase of task control, decision control, environmental control, resource control and technology utilization score, the TT(4) concentration level decreased (P<0.05) . The TT(4) concentration level increased with the increase of the quantiontive load, load changes, job hazards, job prospects, promation opportunities and participaction decision rating (P<0.05) . The total protein concentration level decreased with the increase of task control, decision control, environmental control, resource control, quantitative load, load change, promotion opportunity and participation decision value (P<0.05) , increased with the use degree of technology, work risk, job monotonous, work prospects score rised (P<0.05) . And there were statistically significant differences in the job requirements and job control scores between the low, middle and high levels of occupational factors (P<0.05) . Conclusion: Occupational stress factors of petroleum refining workers have certain influence on the level of thyroid and liver function index.

Fumaric acid production using renewable resources from biodiesel and cane sugar production processes.

The microbial production of fumaric acid by Rhizopus arrhizus NRRL 2582 has been evaluated using soybean cake from biodiesel production processes and very high polarity (VHP) sugar from sugarcane mills. Soybean cake was converted into a nutrient-rich hydrolysate via a two-stage bioprocess involving crude enzyme production via solid state fermentations (SSF) of either Aspergillus oryzae or R. arrhizus cultivated on soybean cake followed by enzymatic hydrolysis of soybean cake. The soybean cake hydrolysate produced using crude enzymes derived via SSF of R. arrhizus was supplemented with VHP sugar and evaluated using different initial free amino nitrogen (FAN) concentrations (100, 200, and 400 mg/L) in fed-batch cultures for fumaric acid production. The highest fumaric acid concentration (27.3 g/L) and yield (0.7 g/g of total consumed sugars) were achieved when the initial FAN concentration was 200 mg/L. The combination of VHP sugar with soybean cake hydrolysate derived from crude enzymes produced by SSF of A. oryzae at 200 mg/L initial FAN concentration led to the production of 40 g/L fumaric acid with a yield of 0.86 g/g of total consumed sugars. The utilization of sugarcane molasses led to low fumaric acid production by R. arrhizus, probably due to the presence of various minerals and phenolic compounds. The promising results achieved through the valorization of VHP sugar and soybean cake suggest that a focused study on molasses pretreatment could lead to enhanced fumaric acid production.

[Influencing factors for reproductive health of female workers in petrochemical industry].

Objective: To investigate the reproductive health status of female workers in petrochemical industry, and to provide a reference for improving reproductive health status and developing preventive and control measures for female workers in petrochemical industry. Methods: A face-to-face questionnaire survey was performed from January to October, 2016. The Questionnaire on Women's Reproductive Health was used to investigate the reproductive health of female workers in petrochemical industry. The multivariate logistic regression model was used to identify the influencing factors for reproductive health of female workers in petrochemical industry. Results: Among the 7485 female workers, 1 268 (40.9%) had abnormal menstrual period, 1 437 (46.4%) had abnormal menstrual volume, 177 (28.5%) had hyperplasia of mammary glands, and 1 807 (24.6%) had gynecological inflammation. The reproductive system diseases in female workers in petrochemical industry were associated with the factors including age, marital status, education level, unhealthy living habits, abortion, overtime work, work shift, workload, video operation, occupational exposure, positive events, and negative events, and among these factors, negative events (odds ratio[OR]= 1.856) , unhealthy living habits (OR=1.542) , and positive events (OR=1.516) had greater impact on reproductive system diseases. Conclusion: Many chemical substances in the occupational environment of petrochemical industry can cause damage to the reproductive system, which not only affects the health of the female workers, but also poses potential threats to the health of their offspring. Occupational exposure, unhealthy living habits, overtime work, and work shift have great influence on reproductive system diseases in female workers.

Environmental impact of the largest petroleum terminal in SE Brazil: A multiproxy analysis based on sediment geochemistry and living benthic foraminifera.

The Dutos e Terminais do Centro Sul (DTCS) is one of the largest petroleum terminals of the South America located in the São Sebastião Channel (SSC) on the southeastern Brazilian coast. The aims of this study were to compare the sediment quality near the DTCS with that of several sites in the SSC region including the Araçá (AR) domestic sewage outfall and to assess the efficiency of the DTCS wastewater treatment plant. To achieve these goals, textural, geochemical, and living benthic foraminifera results were analyzed for the DTCS, AR, and SSC regions. Sediments in the DTCS area were silty with high concentrations of total organic carbon (1.7-2.4%), total nitrogen (0.2-0.3%), total sulfur (0.4-0.6%), and total (0.12-0.18%) and inorganic phosphorous (0.07-0.11%). These values were higher than those in sediments collected in the SSC and Araçá regions. The sediments' concentrations of As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn in the SSC and AR regions were lower than their corresponding probable effect levels (PELs). However, sediments near the DTCS were enriched with As, Cu, and Ni, whose concentrations exceeded their corresponding threshold effect levels (TELs). Around the DTCS outfall diffusers, living foraminiferal densities and diversities were lower than those for the other areas studied. In the DTCS area, it was necessary to search 50 to 190 cm3 of sediment to find 100 live specimens. In the SSC and Araçá areas, a maximum of 40 cm3 of sediment was enough to locate 100 live specimens. The lower density and diversity of living foraminifera around the DTCS than around the other areas illustrates the impact of the environmental stress caused by the presence of pollutants. These results indicate that the wastewater treatment plant efficiency is low and its discharge of pollutants from petrochemical waste liquids affects the benthic fauna around the DTCS in a potentially harmful manner.