Influência da fotobiomodulação na viabilidade e proliferação de células-tronco do ligamento periodontal humano cultivadas na superfície de filmes de ácido polilático / Influence of photobiomodulation on the viability and proliferation of human periodontal ligament stem cells cultured on the surface of polylactic acid films

O ácido polilático (PLA) é um biomaterial com diversas aplicações biomédicas e tem se destacado como um arcabouço promissor na engenharia de tecidos principalmente devido à sua biocompatibilidade, fácil manipulação e baixo custo. O laser de baixa intensidade (LBI) tem se mostrado uma ferramenta útil para promover a bioestimulação in vitro de vários tipos celulares. O objetivo deste estudo foi avaliar o efeito da fotobiomodulação com LBI na viabilidade e proliferação de células-tronco do ligamento periodontal humano (hPDLSC) cultivadas em arcabouços de PLA. Filmes de PLA foram produzidos e a topografia da superfície foi avaliada por microscopia eletrônica de varredura (MEV) e microscopia de força atômica (AFM). As hPDLSC foram isoladas, caracterizadas e cultivadas nos filmes de PLA e os espécimes foram divididos em dois grupos: Controle ­ não irradiado; e Laser ­ submetido à irradiação com laser diodo (InGaAIP) com comprimento de onda de 660 nm, potência de 30 mW, e dose única de 1 J/cm², de modo contínuo. As análises de viabilidade celular foram realizadas 24 e 48 horas após a irradiação através do ensaio bioquímico Alamar Blue e do ensaio Live/Dead. Os eventos do ciclo celular foram avaliados por citometria de fluxo e a morfologia da interação célula-biomaterial foi avaliada por MEV. Os filmes produzidos exibiram uma superfície plana e regular, com presença eventual de pequenos poros e rugosidade média de 59,381 nm. Os resultados do ensaio Alamar Blue mostraram uma maior atividade metabólica celular no grupo irradiado em relação ao controle em 24 (p<0,05) e 48 h (p<0,001), o que foi confirmado no ensaio Live/Dead por uma maior densidade de células viáveis no grupo Laser. Na análise do ciclo celular o grupo Laser apresentou um aumento de células na fase G2/M comparado com o grupo Controle (p<0,001). As imagens da MEV mostraram uma maior densidade celular no grupo irradiado, com manutenção da morfologia. Em conjunto, os achados deste estudo demonstraram que fotobiomodulação tem a capacidade de aumentar a viabilidade e proliferação das células-tronco periodontais cultivadas em arcabouços de PLA, o que pode contribuir para o desenvolvimento de novos estudos utilizando este protocolo na engenharia tecidual periodontal (AU).

Polylactic acid (PLA) is a biomaterial with diverse biomedical applications and has been a promising scaffold in tissue engineering mainly due to its biocompatibility, easy manipulation and low cost. Low-level laser irradiation (LLLI) has been shown to be a powerful tool to promote in vitro biostimulation in several cell types. The aim of this study was to evaluate the effectiveness of photobiomodulation with LLLI on the viability and proliferation of human periodontal ligament stem cells (hPDLSC) cultured on PLA scaffolds. PLA films were produced by solvent casting method and the surface topography was evaluated by scanning electronic microscopy (SEM) and atomic force microscopy (AFM). hPDLSC were isolated, characterized and cultured on the PLA films. Two groups were evaluated: Control - non irradiated; and Laser - irradiated with diode laser (InGaAIP) with wavelength of 660 nm, power of 30 mW, and a single dose of 1 J/cm² with radiation emitted continuously. Cell viability analyzes were performed 24 and 48 hours after irradiation using the the Alamar Blue biochemical assay and Live/Dead assay. Cell cycle events were assessed by flow cytometry and cell-biomaterial morphological interaction was evaluated by SEM. The films produced showed a flat and regular surface, with the occasional presence of small pores and an average roughness of 59.381 nm. The results of Alamar Blue assay showed a greater cell metabolic activity in irradiated group compared to control at 24 (p<0.05) and 48 h (p<0.001), which was confirmed in the Live/Dead assay by a higher density of viable cells in the Laser group. In the analysis of the cell cycle, the Laser group showed an increase of cells in the G2/M phase compared to the Control group (p <0.001). SEM images showed a higher cell density in the irradiated group, with maintenance of cell morphology. Taken together, the findings of this study demonstrated that photobiomodulation has the ability to increase the viability and proliferation of periodontal stem cells cultured on PLA scaffolds, which may contribute to the development of new studies using this protocol in periodontal tissue engineering (AU).

Recovery of motor function after traumatic spinal cord injury by using plasma-synthesized polypyrrole/iodine application in combination with a mixed rehabilitation scheme.

Traumatic spinal cord injury (TSCI) can cause paralysis and permanent disability. Rehabilitation (RB) is currently the only accepted treatment, although its beneficial effect is limited. The development of biomaterials has provided therapeutic possibilities for TSCI, where our research group previously showed that the plasma-synthesized polypyrrole/iodine (PPy/I), a biopolymer with different physicochemical characteristics than those of the PPy synthesized by conventional methods, promotes recovery of motor function after TSCI. The present study evaluated if the plasma-synthesized PPy/I applied in combination with RB could increase its beneficial effects and the mechanisms involved. Adult rats with TSCI were divided into no treatment (control); biopolymer (PPy/I); mixed RB by swimming and enriched environment (SW/EE); and combined treatment (PPy/I + SW/EE) groups. Eight weeks after TSCI, the general health of the animals that received any of the treatments was better than the control animals. Functional recovery evaluated by two scales was better and was achieved in less time with the PPy/I + SW/EE combination. All treatments significantly increased ßIII-tubulin (nerve plasticity) expression, but only PPy/I increased GAP-43 (nerve regeneration) and MBP (myelination) expression when were analyzed by immunohistochemistry. The expression of GFAP (glial scar) decreased in treated groups when determined by histochemistry, while morphometric analysis showed that tissue was better preserved when PPy/I and PPy/I + SW/EE were administered. The application of PPy/I + SW/EE, promotes the preservation of nervous tissue, and the expression of molecules related to plasticity as ßIII-tubulin, reduces the glial scar, improves general health and allows the recovery of motor function after TSCI. The implant of the biomaterial polypyrrole/iodine (PPy/I) synthesized by plasma (an unconventional synthesis method), in combination with a mixed rehabilitation scheme with swimming and enriched environment applied after a traumatic spinal cord injury, promotes expression of GAP-43 and ßIII-tubulin (molecules related to plasticity and nerve regeneration) and reduces the expression of GFAP (molecule related to the formation of the glial scar). Both effects together allow the formation of nerve fibers, the reconnection of the spinal cord in the area of injury and the recovery of lost motor function. The figure shows the colocalization (yellow) of ßIII-tubilin (red) and GAP-43 (green) in fibers crossing the epicenter of the injury (arrowheads) that reconnect the rostral and caudal ends of the injured spinal cord and allowed recovery of motor function.

Two-photon fluorescence imaging and bimodal phototherapy of epidermal cancer cells with biocompatible self-assembled polymer nanoparticles.

We have developed herein an engineered polymer-based nanoplatform showing the convergence of two-photon fluorescence imaging and bimodal phototherapeutic activity in a single nanostructure. It was achieved through the appropriate choice of three different components: a ß-cyclodextrin-based polymer acting as a suitable carrier, a zinc phthalocyanine emitting red fluorescence simultaneously as being a singlet oxygen ((1)O2) photosensitizer, and a tailored nitroaniline derivative, functioning as a nitric oxide (NO) photodonor. The self-assembly of these components results in photoactivable nanoparticles, approximately 35 nm in diameter, coencapsulating a multifunctional cargo, which can be delivered to carcinoma cells. The combination of steady-state and time-resolved spectroscopic and photochemical techniques shows that the two photoresponsive guests do not interfere with each other while being enclosed in their supramolecular container and can thus be operated in parallel under control of light stimuli. Specifically, two-photon fluorescence microscopy allows mapping of the nanoassembly, here applied to epidermal cancer cells. By detecting the red emission from the phthalocyanine fluorophore it was also possible to investigate the tissue distribution after topical delivery onto human skin ex vivo. Irradiation of the nanoassembly with visible light triggers the simultaneous delivery of cytotoxic (1)O2 and NO, resulting in an amplified cell photomortality due to a combinatory effect of the two cytotoxic agents. The potential of dual therapeutic photodynamic action and two-photon fluorescence imaging capability in a single nanostructure make this system an appealing candidate for further studies in biomedical research.

Shape-memory starch for resorbable biomedical devices.

Shape-memory resorbable materials were obtained by extrusion-cooking of potato starch with 20% glycerol under usual conditions. They presented an efficient shape-memory with a high recovery ratio (Rr>90%). Their recovery could be triggered at 37°C in water. After water immersion at 37°C, the modulus decreased from 1GPa to 2.4MPa and remained almost constant over 21 days. Gamma-ray sterilization did not have a dramatic impact on their mechanical properties, despite a large decrease of molecular mass analyzed by asymmetrical flow field-flow fractionation coupled with multi-angle laser light scattering (AFFFF-MALLS). Samples implanted in a rat model exhibited normal tissue integration with a low inflammatory response. Thus, as previously investigated in the case of shape-memory synthetic polymers, natural starch, without chemical grafting, can now be considered for manufacturing innovative biodegradable devices for less-invasive surgery.

Low level laser therapy does not modulate the outcomes of a highly bioactive glass-ceramic (Biosilicate) on bone consolidation in rats.

The main purpose of the present work was to evaluate if low level laser therapy (LLLT) can improve the effects of novel fully-crystallized glass-ceramic (Biosilicate) on bone consolidation in tibial defects of rats. Forty male Wistar rats with tibial bone defects were used. Animals were divided into four groups: group bone defect control (CG); group bone defect filled with Biosilicate (BG); group bone defect filled with Biosilicate, irradiated with LLLT, at 60 J cm(-2) (BG 60) and group bone defect filled with Biosilicate, irradiated with LLLT, at 120 J cm(-2) (BG 120). A low-energy GaAlAs 830 nm, CW, 0.6 mm beam diameter, 100 W cm(-2), 60 and 120 J cm(-2) was used in this study. Laser irradiation was initiated immediately after the surgery procedure and it was performed every 48 h for 14 days. Fourteen days post-surgery, the three-point bending test revealed that the structural stiffness of the groups CG and BG was higher than the values of the groups BG60 and BG120. Morphometric analysis revealed no differences between the control group and the Biosilcate group. Interestingly, the groups treated with Biosilicate and laser (BG 60 and BG120) showed statistically significant lower values of newly formed bone in the area of the defect when compared to negative control (CG) and bone defect group filled with Biosilicate (CB). Our findings suggest that although Biosilicate exerts some osteogenic activity during bone repair, laser therapy is not able to modulate this process.

Biotemplated hierarchical nanostructure of layered double hydroxides with improved photocatalysis performance.

We report a biomorphic hierarchical mixed metal oxide (MMO) framework through a biotemplated synthesis method. A uniform Al(2)O(3) coating was deposited on the surface of the biotemplate with an atomic layer deposition (ALD) process, and the film of ZnAl-layered double hydroxide (ZnAl-LDH), which faithfully inherits the surface structure of the biotemplate, was prepared by an in situ growth technique. Subsequently, a polycrystal ZnAl-MMO framework obtained by calcination of the LDH precursor has been demonstrated as an effective and recyclable photocatalyst for the decomposition of dyes in water, owing to its rather high specific surface area and hierarchical distribution of pore size. Therefore, the new strategy reported in this work can be used to fabricate a variety of biomorphic LDHs as well as MMO frameworks through replication of complicated and hierarchical biological structures for the purpose of catalysis, adsorbents, and other potential applications.

Influence of low-level laser therapy on biomaterial osseointegration: a mini-review.

The aim of this paper is to provide an overview of the available literature on low-level laser therapy (LLLT) and its influence on bone repair and the osseointegration of biomaterials. Extensive studies of alveolar bone repair, a common problem in periodontal therapy, have been conduced worldwide. The utility of LLLT in biomaterial osseointegration is still unanswered, due to lack of literature and poorly understood mechanisms. It is still difficult for one to compare studies about the action of LLLT on the osseointegration of biomaterials because the experimental models and duration of treatments are very distinct. However, it could be concluded that LLLT may offer advantages in terms of periodontal and bone functional recovery and biomaterial osseointegration.

Enzymatic preparation of hollow magnetite microspheres for hyperthermic treatment of cancer.

Ferrimagnetic materials can be expected to be useful as thermal seeds for hyperthermic treatment of cancer, especially where the cancer is located in deep parts of body, as they can generate heat by magnetic hysteretic loss when they are placed in an alternating magnetic field. In this study, hollow magnetite (Fe(3)O(4)) particles were prepared using an enzymatic reaction of urease. A hollow particle was obtained by using a Pasteur pipette. The particle was 500 microm in size and was composed of Fe(3)O(4). Its saturation magnetization and coercive force were 57 emuxg(-1) and 183 Oe, respectively. Its heat generation under an alternating magnetic field of 300 Oe at 100 kHz was estimated to be 45 Wxg(-1). Microspheres 30 microm in diameter were also successfully obtained by using a spray gun.

Wear properties of nano-Al2O3/UHMWPE composites irradiated by gamma ray against a CoCrMo alloy.

Nano-Al(2)O(3)/ultra-high molecular weight polyethylene (UHMWPE) composites were prepared by hot pressing and then radiated by a gamma ray in doses of 120 kGy, 250 kGy and 500 kGy. The hardness of the composites was tested. The friction and wear properties against a CoCrMo alloy were also tested on a knee simulator under physiological saline solution lubrication. The morphologies of worn surfaces were examined under an optical microscope. The structure of the sample was analyzed by IR and XRD tests. The results showed that the wear rate of UHMWPE decreased when filled with a proper amount of nano-Al(2)O(3), and with an increment of the radiation dose of gamma rays. It was found that filling nano-Al(2)O(3) into UHMWPE can inhibit the effect of oxidation during the radiation procedure.

Preparation of ferrimagnetic magnetite microspheres for in situ hyperthermic treatment of cancer.

Ferrimagnetic microspheres 20-30 microm in diameter are useful as thermoseeds for inducing hyperthermia in cancers, especially for tumors located deep inside the body. The microspheres are entrapped in the capillary bed of the tumors when they are implanted through blood vessels and heat cancers locally by their hysteresis loss when placed under an alternating magnetic field. In the present study, preparation of magnetite (Fe(3)O(4)) microspheres 20-30 microm in diameter was attempted by melting powders in high-frequency induction thermal plasma, and by precipitation from aqueous solution. The microspheres prepared by melting powders in high-frequency induction thermal plasma were composed of a large amount of Fe(3)O(4) and a small amount of wustite (FeO), and those subsequently heat treated at 600 degrees C for 1 h under 5.1 x 10(3) Pa were fully composed of Fe(3)O(4) 1 microm in size. The saturation magnetization and coercive force of the heat-treated microspheres were 92 emu g(-1) and 50 Oe, respectively. The heat generation of the heat-treated microspheres was estimated to be 10 Wg(-1), under 300 Oe and 100 kHz. The microspheres prepared by precipitation from aqueous solution consisted of beta-FeOOH, and those subsequently heat treated at 400 degrees C for 1 h in a 70% CO(2) + 30% H(2) atmosphere consisted of Fe(3)O(4) crystals 50 nm in size. The saturation magnetization and coercive force of the heat-treated microspheres were 53 emu g(-1) and 156 Oe, respectively. The heat generation of the heat-treated microspheres was estimated to be 41 Wg(-1), under 300 Oe and 100 kHz. The latter microspheres are believed to be promising thermoseeds for hyperthermic treatment of cancer.

Influence of gamma-irradiation sterilization on the structural defects of sapphire single crystals (alpha-Al(2)O(3)).

The influence of sterilization by gamma rays on the structure and the electrical behaviour of sapphire single crystal (alpha-Al(2)O(3)) was studied successively by thermoluminescence, by cathodoluminescence and by observation of the scanning electron microscope mirror effect. The mirror method allowed us to measure the capacity of an insulating material to trap electrons. The structural analysis of the alpha-Al(2)O(3) showed that there were oxygen vacancies, as well as chromium and titanium impurities. It was possible to demonstrate that these defects, especially the oxygen vacancies, are in a different state after a 30 kilogray irradiation. The valency state changes of these defects and the presence of trapped charges are accompanied by a deformation of the crystalline lattice which results in a modification of its electrical properties. At room temperature, the irradiated alpha-Al(2)O(3), unlike non irradiated alpha-Al(2)O(3), is capable of trapping electrons. It can be concluded that gamma-ray sterilization modifies the cohesive energy of alpha-Al(2)O(3), which could lead to mechanical changes (surface charge, friction, wear, fracture strength, em leader) in this material.

Phase, compositional, and morphological changes of human dentin after Nd:YAG laser treatment.

Although techniques for repairing root fracture have been proposed, the prognosis is generally poor. If the fusion of a root fracture by laser is possible, it will offer an alternative to extraction. Our group has attempted to use lasers to fuse a low melting-point bioactive glass to fractured dentin. This report is focused on the phase, compositional, and morphological changes observed by means of X-ray diffractometer, Fourier transforming infrared spectroscopy, and scanning electron microscopy-energy dispersive X-ray spectroscopy in human dentin after exposure to Nd:YAG laser. The irradiation energies were from 150 mJ/ pulse-10 pps-4 s to 150 mJ/pulse-30 pps-4 s. After exposure to Nd:YAG laser, dentin showed four peaks on the X-ray diffractometer that corresponding to a-tricalcium phosphate (TCP) and beta-TCP at 20 = 30.78 degrees/34.21 degrees and 32.47 degrees/33.05 degrees, respectively. The peaks of a-TCP and beta-TCP gradually increased in intensity with the elevation of irradiation energy. In Fourier transforming infrared analysis, two absorption bands at 2200 cm(-1) and 2015 cm(-1) could be traced on dentin treated by Nd:YAG laser with the irradiation energies beyond 150 mJ/pulse-10 pps-4 s. The energy dispersive X-ray results showed that the calcium/phosphorus ratios of the irradiated area proportionally increased with the elevation of irradiation energy. The laser energies of 150 mJ/ pulse-30 pps-4 s and 150 mJ/pulse-20 pps-4 s could result in the a-TCP formation and collagen breakdown. However, the formation of glass-like melted substances without a-TCP at the irradiated site was induced by the energy output of 150 mJ/ pulse-10 pps-4 s. Scanning electron micrographs also revealed that the laser energy of 150 mJ/ pulse-10 pps-4 s was sufficient to prompt melting and recrystallization of dentin crystals without cracking. Therefore, we suggest that the irradiation energy of Nd:YAG laser used to fuse a low melting-point bioactive glass to dentin is 150 mJ/ pulse-10 pps-4 s.