Microbial intervention improves pollutant removal and semi-liquid organo-mineral fertilizer production from olive mill wastewater sludge and rock phosphate.

Olive mill wastewater sludge (OMWS) represents a residual pollutant generated by the olive oil industry, often stored in exposed evaporation ponds, leading to contamination of nearby land and water resources. Despite its promising composition, the valorization of OMWS remains underexplored compared to olive mill wastewater (OMW). This study aims to identify potent native microbial species within OMWS suitable for bioremediation and its transformation into a high-value organic fertilizer. The microbial screening, based on assessing OMWS tolerance and phosphate solubilization properties in vitro, followed by a singular inoculation using a mixture of OMWS and rock phosphate (RP). Identification of FUN 06 (Galactomyces Geotrichum), a fungal species, employed as an inoculant in the treatment of sterile OMWS supplemented with RP. Results demonstrate that fungal inoculation notably diminished OMWS phytotoxicity while enhancing its physicochemical parameters, nutrient concentrations, and removal of toxic organic compounds by up to 90% compared to the control, and enhances plant growth, offering a sustainable approach to tackle environmental concerns. Additionally, metataxonomic analysis unveiled FUN 06's propensity to enhance the presence of microbial species engaged in pollutant degradation. However, higher RP dosage (10%) appeared to adversely affect bioprocess efficiency, suggesting a potential dose-related effect. Overall, FUN 06, isolated from OMWS evaporation ponds, shows promise for effective bioremediation and sustainable reuse. In fact, our results indicate that targeted microbial inoculation stands as an effective strategy for mitigating pollutants in OMWS, facilitating its conversion into a nutrient-rich organo-mineral fertilizer suitable for direct use, promoting its beneficial reuse in agriculture, thereby presenting a promising avenue for olive oil waste management.

Performance of electro-Fenton process for the treatment of synthetic sulphidic spent caustic waste stream generated from petroleum refineries.

Sulphidic spent caustic (SSC) is an alkaline waste stream which is generated during caustic scrubbing of liquefied petroleum gas and ethylene products. Due to presence of high concentrations of sulphides and phenols, the waste stream requires proper treatment before mixing with the low strength wastewater streams produced from other refinery operations. Electrochemical process is an emerging treatment method that can work efficiently at ambient conditions. The present study reports performance of electro-Fenton (EF) process for the treatment of synthetic SSC wastewater (sulphides = 10 g L-1, phenol = 2 g L-1 and pH = 12.9). The EF runs were carried out for 2 h duration in a reactor equipped with iron electrodes. The effects of H2O2 dose (0.26-1.3 M), current density (1-20 mA cm-2), pH (4.5-12.9) and stirring speed (100-1000 rpm) were investigated on removal of pollutants. The H2O2 was rapidly consumed in initial 30 min during which the significant fraction of the pollutants was degraded or removed. The optimum conditions for EF process were found to be as follows: pH = 4.5, H2O2 dose = 1.05 M, current density = 5 mA cm-2 and stirring speed = 500 rpm. At these conditions, the maximum sulphide and phenol removals from the wastewater were 98% and 91%, respectively. The results will be helpful to the wastewater treatment plant operators worldwide dealing with high concentrations of such pollutants.

Upcycling crab shell waste into biochar for treatment of palm oil mill effluent via microwave pyrolysis and activation.

The escalating consumer demand for crabs results in a growing amount of waste, including shells, claws, and other non-edible parts. The resulting crab shell waste (CSW) is disposed of via incineration or landfills which causes environmental pollution. CSW represents a potential biological resource that can be transformed into valuable resources via pyrolysis technique. In this study, microwave pyrolysis of CSW using self-purging, vacuum, and steam activation techniques was examined to determine the biochar production yield and its performance in treating palm oil mill effluent (POME). The biochar produced through microwave pyrolysis exhibits yields ranging from 50 to 61 wt%, showing a hard texture, low volatile matter content (≤34.1 wt%), and high fixed carbon content (≥58.3 wt%). The KOH-activated biochar demonstrated a surface area of up to 177 m2/g that is predominantly composed of mesopores, providing a good amount of adsorption sites for use as adsorbent. The biochar activated with steam removed 8.3 mg/g of BOD and 42 mg/g of COD from POME. The results demonstrate that microwave pyrolysis of CSW is a promising technology to produce high-quality biochar as an adsorbent for POME treatment.

Mineralization of palm oil mill effluent by advanced oxidation processes: A review on current trends and the way forward.

Palm oil mill effluent (POME) is regarded as deleterious to the environment, primarily owing to the substantial volume of waste it produces during palm oil extraction. In terms of contaminant composition, POME surpasses the pollutant content typically found in standard municipal sewage, therefore releasing it without treatment into water bodies would do irreparable damage to the environment. Main palm oil mills are normally located in the proximity of natural rivers in order to take advantage of the cheap and abundant water source. The same rivers are also used as a water source for many villages situated along the river banks. As such, it is imperative to degrade POME before its disposal into the water bodies for obvious reasons. The treatment methods used so far include the biological processes such as open ponding/land application, which consist of aerobic as well as anaerobic ponds, physicochemical treatment including membrane technology, adsorption and coagulation are successful for the mitigation of contaminants. As the above methods require large working area and it takes more time for contaminant degradation, and in consideration of the strict environmental policies as well as palm oil being the most sort of vegetable oil in several countries, numerous researchers have concentrated on the emerging technologies such as advanced oxidation processes (AOPs) to remediate POME. Methods such as the photocatalysis, Fenton process, sonocatalysis, sonophotocatalysis, ozonation have attained special importance for the degradation of POME because of their efficiency in complete mineralization of organic pollutants in situ. This review outlines the AOP technologies currently available for the mineralization of POME with importance given to sonophotocatalysis and ozonation as these treatment process removes the need to transfer the pollutant while possibly degrading the organic matter sufficiently to be used in other industry like fertilizer manufacturing.

Characterisation of synthesised trimetallic nanoparticles and its influence on anaerobic digestion of palm oil mill effluent.

The augmentation of biogas production can be achieved by incorporating metallic nanoparticles as additives within anaerobic digestion. The objective of this current study is to examine the synthesis of Fe-Ni-Zn and Fe-Co-Zn trimetallic nanoparticles using the co-precipitation technique and assess its impact on anaerobic digestion using palm oil mill effluent (POME) as carbon source. The structural morphology and size of the synthesised trimetallic nanoparticles were analysed using a range of characterization techniques, such as X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and Energy-dispersive X-ray spectroscopy (EDX) . The average size of Fe-Ni-Zn and Fe-Co-Zn were 19-25.5 nm and 19.1-30.5 nm respectively. Further, investigation focused on examining the diverse concentrations of trimetallic nanoparticles, ranging from 0 to 50 mgL-1. The biogas production increased by 55.55% and 60.11% with Fe-Ni-Zn and Fe-Co-Zn trimetallic nanoparticles at 40 mgL-1 and 20 mgL-1, respectively. Moreover, the lowest biogas of 11.11% and 38.11% were found with 10 mgL-1 of Fe-Ni-Zn and Fe-Co-Zn trimetallic nanoparticles. The findings of this study indicated that the trimetallic nanoparticles exhibited interactions with anaerobes, thereby enhancing the degradation process of palm oil mill effluent (POME) and biogas production. The study underscores the potential efficacy of trimetallic nanoparticles as a viable supplement for the promotion of sustainable biogas generation.

Olive mill wastewater treatment using natural adsorbents: phytotoxicity on durum wheat (Triticum turgidum L. var. durum) and white bean (Phaseolus vulgaris L.) seed germination.

This research was undertaken to optimize the phenolic compound removal from Olive Mill Wastewater (OMW) by sawdust and red clay as natural adsorbents. Fractional factorial experimental design at 25-1 was used in order to optimize the experimental conditions for high removal efficiency. Statistics ANOVA analysis, Fisher's test, and Student's test suggested that the adsorbent dose has the most significant influence on polyphenol removal for both adsorbents. The maximum removal of polyphenols by sawdust reached 49.6% at 60 °C by using 60 g/L of adsorbent dose, pH 2, reaction time of 24 h, and agitation speed of 80 rpm. Whereas, for red clay, 48.08% of polyphenols removal was observed under the same conditions for sawdust except the temperature of 25 °C instead of 60 °C. In addition, the thermodynamic parameters suggested spontaneous process for both adsorbents, endothermic for the sawdust and exothermic for red clay. Furthermore, the phytotoxicity effect of OMW on durum wheat (Triticum turgidum L. var. durum) and white bean (Phaseolus vulgaris L.) seed germination was investigated. The obtained results showed that the untreated OMW inhibited the seed germination of T. turgidum and P. vulgaris seeds. OMW treatment with red clay followed by dilution (95% water) resulted in 87 and 30% germination of P. vulgaris and T. turgidum, respectively. While, the treatment of OMW with sawdust and dilution at 95% resulted in 51 and 26% germination of P. vulgaris and T. turgidum, respectively.

Environmental implications of phosphate-based fertilizer industrial waste and its management practices.

During the green revolution in the mid-twentieth century, the consumption of inorganic phosphorous and phosphate-based fertilizers (P-fertilizers) in the developing world skyrocketed, resulting in a proliferation of P-fertilizer industries. Phosphate-based fertilizer industries are ranked among the most environment-polluting industries. The worldwide phosphorus market, which was 68.5 million metric tons in 2020, is expected to increase at a compound annual growth rate (CAGR) of 2.5% to 81 million metric tons by 2027. The release of untreated hazardous pollutants from these fertilizer industries into the soil, water, and atmosphere has resulted in severe environmental health issues. Excessive surface runoff of phosphorus from agricultural fields and its deposition in water promote the growth of algae and macrophytes and lower dissolved oxygen concentration through eutrophication, which is detrimental to aquatic life. Fluorides (F-) and sulfur dioxide (SO2) and/or heavy metals (potentially toxic elements, PTEs) are also detected in the emissions from these fertilizer industries. The main solid waste generated from the phospho-gypsum plant produced up to 5 tons of di-hydrogen phosphate (H2PO4), including PTEs and radioactive substances. Phosphates and fluorenes from these industries are usually disposed of as sludge in storage ponds or trash piles. Humans inhaling poisonous gases released from the P-fertilizer industries can develop hepatic failure, autoimmune diseases, pulmonary disorders, and other health problems. The objectives of this review are to provide guidelines for eliminating the bottleneck pollutions that occur from the phosphate-based fertilizer industries and explore the management practices for its green development.

Application of common industrial solid waste in water treatment: a review.

Industrial solid waste has a wide range of impacts, and it is directly or indirectly related to land, atmosphere, water, and other resources. Industrial solid waste has a large amount of production, complex and diverse components and contains a variety of harmful substances. However, as industrial by-products, it also has a lot of available value. Industrial solid waste has been continuously studied in water treatment due to its special composition and porous and loose structure. It is known that there are few reviews of various industrial solid wastes in the field of wastewater treatment, and most of them only discuss single industrial solid waste. This paper aims to sort out the different studies on various solid wastes such as fly ash, red mud, wastewater sludge, blast furnace slag and steel slag in dyeing, heavy metal, and phosphorus-containing wastewater. Based on the modification of industrial solid waste and the preparation of composite materials, adsorbents, coagulants, catalysts, filtration membranes, geological polymers, and other materials with high adsorption properties for pollutants in wastewater were formed; the prospect and development of these materials in the field of wastewater were discussed, which provides some ideas for the mutual balance of environment and society. Meanwhile, some limitations of solid waste applications for wastewater treatment have been put forward, such as a lack of further researches about environment-friendly modification methods, application costs, the heavy metal leaching, and toxicity assessment of industrial solid waste.

Insights into bacterial community metatranscriptome and metabolome in river water influenced by palm oil mill effluent final discharge.

AIMS: This study aimed to investigate the effect of palm oil mill effluent (POME) final discharge on the active bacterial composition, gene expression, and metabolite profiles in the receiving rivers to establish a foundation for identifying potential biomarkers for monitoring POME pollution in rivers. METHODS AND RESULTS: The POME final discharge, upstream (unpolluted by POME), and downstream (effluent receiving point) parts of the rivers from two sites were physicochemically characterized. The taxonomic and gene profiles were then evaluated using de novo metatranscriptomics, while the metabolites were detected using qualitative metabolomics. A similar bacterial community structure in the POME final discharge samples from both sites was recorded, but their composition varied. Redundancy analysis showed that several families, particularly Comamonadaceae and Burkholderiaceae [Pr(>F) = 0.028], were positively correlated with biochemical oxygen demand (BOD5) and chemical oxygen demand (COD). The results also showed significant enrichment of genes regulating various metabolisms in the POME-receiving rivers, with methane, carbon fixation pathway, and amino acids among the predominant metabolisms identified (FDR < 0.05, PostFC > 4, and PPDE > 0.95). This was further validated through qualitative metabolomics, whereby amino acids were detected as the predominant metabolites. CONCLUSIONS: The results suggest that genes regulating amino acid metabolism have significant potential for developing effective biomonitoring and bioremediation strategies in river water influenced by POME final discharge, fostering a sustainable palm oil industry.

Treatment of diluted palm oil mill effluent (POME) synchronous with electricity production in a persulfate oxidant-promoted photocatalytic fuel cell.

Attributable to the prosperous production growth of palm oil in Malaysia, the generated palm oil mill effluent (POME) poses a high threat owing to its highly polluted characteristic. Urged by the escalating concern of environmental conservation, POME pollution abatement and potential energy recovery from the effluent are flagged up as a research topic of interest. In this study, a cutting-edge photocatalytic fuel cell (PFC) system with employment of ZnO/Zn nanorod array (NRA) photoanode, CuO/Cu cathode, and persulfate (PS) oxidant was successfully designed to improve the treatment of POME and simultaneous energy production. The photoelectrodes were fabricated and characterized by field emission scanning electron microscopy with energy (FESEM), X-ray diffraction (XRD), energy-dispersive X-ray (EDX), and Brunauer, Emmett, and Teller analysis (BET). Owing to the properties of strong oxidant of PS, the proposed PFC/PS system has exhibited exceptional performance, attaining chemical oxygen demand (COD) removal efficiency of 96.2%, open circuit voltage (Voc) of 740.0 mV, short circuit current density (Jsc) of 146.7 µA cm-2, and power density (Pmax) of 35.6 µW cm-2. The pre-eminent PFC/PS system performance was yielded under optimal conditions of 2.5 mM of persulfate oxidant, POME dilution factor of 1:20, and natural solution pH of 8.51. Subsequently, the postulated photoelectrocatalytic POME treatment mechanism was elucidated by the radical scavenging study and Mott-Schottky (M-S) analysis. The following recycling test affirmed the stability and durability of the photoanode after four continuous repetition usages while the assessed electrical energy efficiency revealed the economic viability of PFC system serving as a post-treatment for abatement of POME. These findings contributed toward enhancing the sustainability criteria and economic viability of palm oil by adopting sustainable and efficient POME post-treatment technology.

Valorization of pistachio industrial waste: Simultaneous recovery of pectin and phenolics, and their application in low-phenylalanine cookies for phenylketonuria.

This study introduces a sustainable approach to simultaneously produce pectin and phenolic compounds from pistachio industrial waste and applies them in the formulation of low-phenylalanine cookies. The co-optimization process was performed using the microwave-assisted technique and a Box-Behnken design, considering four variables and two responses: pectin yield and total phenolic content (TPC). The co-optimized condition (microwave power of 700 W, irradiation time of 210 s, pH level of 1.02, and LSR of 20 mL/g) resulted in a pectin yield of 15.85 % and a TPC of 10.12 %. The pectin obtained under co-optimized condition was evaluated for its physicochemical, structural, and thermal properties and the phenolic extract for its antiradical activity. Characterization of the pectin sample revealed a high degree of esterification (44.21 %) and a galacturonic acid-rich composition (69.55 %). The average molecular weight of the pectin was determined to be 640.236 kDa. FTIR and 1H NMR spectroscopies confirmed the structure of pectin, with an amorphous nature and high thermal stability observed through XRD and DSC analysis. Additionally, the extract exhibited significant antiradical activity comparable to butylated hydroxyanisole and ascorbic acid. The isolated ingredients were used to formulate low-protein, low-phenylalanine cookies for phenylketonuria patients. The addition of 0.5 % pectin and 1 mL/g extract led to increased moisture content (from 9.05 to 12.89 %) and specific volume (from 7.28 to 9.90 mL/g), decreased hardness (from 19.44 to 10.39 N × 102), and improved antioxidant properties (from 5.15 % to 44.60 % inhibition) of the cookies. Importantly, there was no significant increase observed in the phenylalanine content of the samples with pectin and extract addition. Furthermore, sensory evaluation scores demonstrated significantly higher scores for taste, odor, texture, and overall acceptability in cookies enriched with 0.5 % pectin and 1 mL/g extract, with scores of 4.53, 3.93, 4.40, and 4.60, respectively.

Acute toxicity of palm oil mill effluent on zebrafish (Danio rerio Hamilton-Buchanan, 1822): Growth performance, behavioral responses and histopathological lesions.

Evaluating the toxicity of Palm Oil Mill Effluent (POME) is critical as part of the effort to develop waste management regulations for the palm oil industry. In this study, we investigated the acute toxicity of POME on growth performance, behavioral response, and histopathology of gill and liver tissues of zebrafish (Danio rerio). In total, 550 adult male zebrafish were used for the toxicity experiment including range finding test, acute toxicity test, growth performance and behaviour test. Static non-renewal acute toxicity bioassays were conducted by exposing fish to POME (1.584-9.968 mL/L) for 96 h. Growth performance, behavior response, and histopathological lesions in untreated and POME treated (96-h LC50: 5.156 mL/L) fish were measured at 24, 48, 72 and 96 h. Time-dependent significant decline in body length and body weight of POME-exposed zebrafish was observed. Furthermore, several behavioral changes were recorded, including hyperactivity, loss of balance, excessive mucus secretion, and depigmentation. Decreasing operculum movement and oxygen consumption rate as well as alterations in gill tissues (i.e. hyperplasia, hypertrophy, hemorrhage, and necrosis) of POME-exposed zebrafish were observed, suggesting a dysfunction in respiratory performance. On the other hand, liver tissue alterations (congestion, hemorrhage, hyperplasia, shrinkage of hepatocytes, hydrophilic degeneration, and necrosis) indicated a disruption in detoxification performance. We conclude that exposure to POME at acute concentration caused histopathological lesions both in gill and liver tissue along with changes in fish behaviors which disrupted respiratory and detoxification performance, resulting in mortality and reduced growth of zebrafish. These findings might provide valuable information for guiding POME management and regulation.

Innovative production of value-added products using agro-industrial wastes via solid-state fermentation.

The prevalence of organic solid waste worldwide has turned into a problem that requires comprehensive treatment on all fronts. The amount of agricultural waste generated by agro-based industries has more than triplet. It not only pollutes the environment but also wastes a lot of beneficial biomass resources. These wastes may be utilized as a different option/source for the manufacturing of many goods, including biogas, biofertilizers, biofuel, mushrooms and tempeh as the primary ingredients in numerous industries. Utilizing agro-industrial wastes as good raw materials may provide cost reduction and lower environmental pollution levels. Agro-industrial wastes are converted into biofuels, enzymes, vitamin supplements, antioxidants, livestock feed, antibiotics, biofertilizers and other compounds via solid-state fermentation (SSF). By definition, SSF is a method used when there is little to no free water available. As a result, it permits the use of solid materials as biotransformation substrates. Through SSF methods, a variety of microorganisms are employed to produce these worthwhile things. SSFs are therefore reviewed and discussed along with their impact on the production of value-added items. This review will provide thorough essential details information on recycling and the use of agricultural waste.

Optimized photodegradation of palm oil agroindustry waste effluent using multivalent manganese-modified black titanium dioxide.

This article presents a methodological approach to use manganese (Mn3+Mn7+)-modified black titanium dioxide (Mn/BTiO2) as a photocatalyst to optimize and improve visible-light-driven photodegradation of treated agro-industrial effluent (TPOME). A modified wet chemical process was used to prepare BTiO2. The BTiO2 was then wet impregnated with Mn and calcined at 300 °C for 1 h to produce Mn/BTiO2. The activity of Mn/BTiO2 was investigated in terms of photo-assisted elimination of chemical oxygen demand (COD), phenolic compounds (PCs), color, and total organic carbon (TOC). Using the design of experiments (DOE), the conditions of the photocatalytic process, including photocatalyst loading, Mn concentration, hydrogen peroxide (H2O2) dose, and irradiation time, were optimized. Under the optimum conditions (0.85 g/L photocatalyst loading, 0.048 mol/L H2O2 dose, 0.301 wt.% Mn concentration, and 204 min irradiation time) COD, PCs, color, and TOC removal efficiencies of 88.87%, 86.04%, 62.8%, and 84.66%, respectively, were obtained. Statistical analysis showed that the response variable's removal from TPOME estimation had high R2 and low RMSE, MSE, MAD, MAE, and MAPE values, indicating high reliability. This study demonstrated the significant potential of the developed photocatalytic system for the treatment of waste effluent generated by the palm oil industry and other agro-industries, with the ability to simultaneously reduce a number of organic pollution indicators (OPIs).

A review on the pollution assessment of hazardous materials and the resultant biorefinery products in Palm oil mill effluent.

The voluminous nature of palm oil mill effluent (POME) is directly associated with environmental hazards and could be turned into biorefinery products. The POME, rich in BOD, COD, and oil and grease, with few hazardous materials such as siloxanes, fatty acid methyl ester, and phenolic compounds that may significantly increase the risk of violating the effluent quality standards. Recently, the application of chemical and biological risk assessment that can use electrochemical sensors and microalgae-like species has gained paramount attention towards its remediation. This review describes the existing risk assessment for POME and recommends a novel assessment approach using fish species including invasive ones as suitable for identifying the toxicants. Various physico-chemical and biological treatments such as adsorption, coagulation-flocculation, photo-oxidation, solar-assisted extraction, anaerobic digestion, integrated anaerobic-aerobic, and microalgae cultivation has been investigated. This paper offers an overview of anaerobic technologies, with particular emphasis on advanced bioreactors and their prospects for industrial-level applications. To illustrate, palmitic acid and oleic acid, the precursors of fatty acid methyl ester found in POME pave the way to produce biodiesel with 91.45%. Although there are some challenges in attaining production at an economic scale, this review offers some opportunities that could help in overcoming these challenges.

Utilization of ferrous slags as coagulants, filters, adsorbents, neutralizers/stabilizers, catalysts, additives, and bed materials for water and wastewater treatment: A review.

Solid waste is currently produced in substantial amounts by industrial activities. While some are recycled, the majority of them are dumped in landfills. Iron and steel production leaves behind ferrous slag, which must be created organically, managed wisely and scientifically if the sector is to remain more sustainably maintained. Ferrous slag is the term for the solid waste that is produced when raw iron is smelted in ironworks and during the production of steel. Both its specific surface area and porosity are relatively high. Since these industrial waste materials are so easily accessible and offer such serious disposal challenges, the idea of their reuse in water and wastewater treatment systems is an appealing alternative. There are many components such as Fe, Na, Ca, Mg, and silicon found in ferrous slags, which make it an ideal substance for wastewater treatment. This research investigates the potential of ferrous slag as coagulants, filters, adsorbents, neutralizers/stabilizers, supplementary filler material in soil aquifers, and engineered wetland bed media to remove contaminants from water and wastewater. Ferrous slag may provide a substantial environmental risk before or after reuse, so leaching and eco-toxicological investigations are necessary. Some study revealed that the amount of heavy metal ions leached from ferrous slag conforms to industrial norms and is exceedingly safe, hence it may be employed as a new type of inexpensive material to remove contaminants from wastewater. The practical relevance and significance of these aspects are attempted to be analyzed, taking into account all recent advancements in the fields, in order to help in the development of informed decisions about future directions for research and development related to the utilization of ferrous slags for wastewater treatment.

Is Policy the Necessary or Sufficient Driving Force of Construction and Demolition Waste Recycling Industry Development? Experience from China.

Policies have long been considered the essential driving force in promoting construction and demolition waste (CDW) recycling. However, the policy instruments adopted in different economies have varied greatly, which contributes to the difficulty in quantitative discernment of their effect. This study aims to examine whether the holistic employment of policy measures determines the development of CDW recycling around China. To accurately measure the holistic adoption of CDW policies, this study assessed policy strength via a proposed three-dimensional evaluation model. The spatiotemporal differences in policy strength among the 52 sample cities were further defined using K-means clustering and the Gini coefficient. Next, the driving effect of policy on the initial establishment of CDW recycling industry practices was examined by event history analysis (EHA). Finally, fuzzy set qualitative comparative analysis (fsQCA) was used to analyze the sufficiency and necessity of policy for the initial establishment of CDW recycling practices. The results indicated that the establishment of a first CDW recycling plant is only slightly correlated with policy measures, whereas it is highly correlated with the pilot city and per capita GDP. Furthermore, application of policy is neither a necessary nor sufficient condition for the establishment of a CDW recycling industry facility.

Efficient removal of tannins from anaerobically-treated palm oil mill effluent using protein-tannin complexation in conjunction with electrocoagulation.

Despite the significant removal of chemical oxygen demand (COD) by anaerobic digestion, anaerobically-treated palm oil mill effluent (POME) still contains tannins and other phenolic compounds, resulting in residual COD and a brownish color. In this study, we investigated the removal of tannins from anaerobically treated POME using protein-tannin complexation in conjunction with electrocoagulation. The amino acid composition of the protein, aqueous pH, and protein: tannin ratios were found to be important parameters affecting the tannin removal efficiency. Pig blood protein was superior to casein protein in removing tannins, possibly because it had aspartic acid as the major amino acid component. At an optimal condition with a pig blood protein: tannin ratio of 0.33 (w/w), a current density of 30 mA/cm2, pH 5, and an electrolysis time of 10 min, the removals of tannins, COD, and color were 93%, 96%, and 97%, respectively.

Bioactive Compounds in Extracts from the Agro-Industrial Waste of Mango.

Mango by-products are important sources of bioactive compounds generated by agro-industrial process. During mango processing, 35-60% of the fruit is discarded, in many cases without treatment, generating environmental problems and economic losses. These wastes are constituted by peels and seeds (tegument and kernel). The aim of this review was to describe the extraction, identification, and quantification of bioactive compounds, as well as their potential applications, published in the last ten years. The main bioactive compounds in mango by-products are polyphenols and carotenoids, among others. Polyphenols are known for their high antioxidant and antimicrobial activities. Carotenoids show provitamin A and antioxidant activity. Among the mango by-products, the kernel has been studied more than tegument and peels because of the proportion and composition. The kernel represents 45-85% of the seed. The main bioactive components reported for the kernel are gallic, caffeic, cinnamic, tannic, and chlorogenic acids; methyl and ethyl gallates; mangiferin, rutin, hesperidin, and gallotannins; and penta-O-galloyl-glucoside and rhamnetin-3-[6-2-butenoil-hexoside]. Meanwhile, gallic acid, ferulic acid, and catechin are reported for mango peel. Although most of the reports are at the laboratory level, they include potential applications in the fields of food, active packaging, oil and fat, and pharmaceutics. At the market level, two trends will stimulate the industrial production of bioactive compounds from mango by-products: the increasing demand for industrialized fruit products (that will increase the by-products) and the increase in the consumption of bioactive ingredients.

Chemical Composition, Antioxidant Activity and Cytocompatibility of Polyphenolic Compounds Extracted from Food Industry Apple Waste: Potential in Biomedical Application.

Apple pomace (AP) from the food industry is a mixture of different fractions containing bioactive polyphenolic compounds. This study provides a systematic approach toward the recovery and evaluation of the physiochemical and biological properties of polyphenolic compounds from AP. We studied subcritical water extraction (SCW) and solvent extraction with ethanol from four different AP fractions of pulp, peel, seed, core, and stem (A), peel (B), seed and core (C), and pulp and peel (D). The subcritical water method at the optimum condition resulted in total polyphenolic compounds (TPC) of 39.08 ± 1.10 mg GAE per g of AP on a dry basis compared to the ethanol extraction with TPC content of 10.78 ± 0.94 mg GAE/g db. Phloridzin, chlorogenic acid, and quercetin were the main identified polyphenolics in the AP fractions using HPLC. DPPH radical scavenging activity of fraction B and subcritical water (SW) extracts showed comparable activity to ascorbic acid while all ethanolic extracts were cytocompatible toward human fibroblast (3T3-L1) and salivary gland acinar cells (NS-SV-AC). Our results indicated that AP is a rich source of polyphenolics with the potential for biomedical applications.