Hybrid ceramic repair strength, surface roughness, and bond failure, using methylene blue-activated low-level laser therapy, Carbon dioxide, and Ti: Al2O3 laser.

AIMS: To evaluate the impact of various pretreatment regimes (LLLT, Ti-sapphire laser, CO2, and HFA-S) on hybrid ceramics, specifically focusing on their ability to enhance repair strength and minimize surface roughness (Ra). MATERIAL AND METHODS: Discs were made from hybrid ceramics and after disinfection were randomly divided into four groups based on different surface conditioning techniques. Each group consisted of 15 discs, resulting in a total sample size of 60. dics in group 1 was surface treated with Low-level laser therapy (LLLT) using methylene blue (MB), Discs in group 2 with Ti-sapphire laser, Discs in group 3 with CO2 laser, and discs in group 4 with HFA-S. Five samples from each group were assessed for Ra. The remaining 10 samples from each group underwent repair using a porcelain repair kit in adherence to the planned instructions. The bond strength of each sample in all groups was measured using a universal testing machine. Following the bond strength testing, the specimens from all study groups were analyzed to determine the mode of failure. To evaluate the data, a two-way analysis of variance (ANOVA) was used, followed by post hoc multiple comparisons. RESULTS: The highest repair bond strength was observed in group 4 hybrid ceramics pretreated with HFA-S (19.05±0.79 MPa). The lowest repair bond scores were observed in group 1 hybrid ceramics preconditioned with LLLT in the presence of Photosensitizer (13.41±0.36 MPa). The highest Ra scores were exhibited in group 2 surface treated with Ti-sapphire laser (0.0515±0.16 µm) and the lowest Ra scores were observed in Group 4 HFA-S (0.0311±0.79 µm). Predominant bond failure among different investigated groups was cohesive. CONCLUSION: The current gold standard for hybrid ceramic conditioning is the use of hydrofluoric acid (HFA) combined with a silane coupling agent. Low-level laser therapy with methylene blue photosensitizer is not recommended for the treatment of hybrid ceramics.

Efficacy of methylene blue and curcumin mediated antimicrobial photodynamic therapy in the treatment of indirect pulp capping in permanent molar teeth.

PURPOSE: This study aimed to evaluate the adhesive bond strength and antibacterial efficacy of methylene blue (MB)-mediated antimicrobial photodynamic therapy (aPDT) and curcumin (CUR)-mediated aPDT versus the conventional disinfectants, such as chlorhexidine gluconate (CHX) gel and sodium hypochlorite (NaOCl), for indirect pulp capping (IPC) treatment of permanent molars. METHODS: One Hundred grossly carious human permanent molars were collected through non-traumatic extraction. All specimens were embedded in polyvinyl cross-sections to the cemento-enamel junction. The cavity preparation was conducted by grinding the samples using silicon carbide discs. After culturing Streptococcus mutans (S. mutans), a 10 µL of S. mutans suspension (106 colony forming units/mL) was transferred in each tooth cavity and anaerobically incubated for 48 h at 37 °C. All specimens were randomly divided into 5 groups: Group-I: samples treated IPC; Group-II: samples treated with 2% CHX gel; Group-III: samples treated with 6% NaOCl; Group-IV: irradiation of prepared cavity with MB-mediated aPDT; and Group-V: irradiation of prepared cavity with CUR-mediated aPDT. After disinfection methods, the universal adhesive was used, and all specimens were restored using giomer. Eventually, confocal laser scanning microscopy, shear bond strength (SBS), micro-tensile bond strength (µTBS), four-point bending strength (4P-BS) analyses were performed, and the data were analyzed statistically. RESULTS: At baseline, the highest SBS (48.8 ± 6.5 MPa), µTBS (54.3 ± 3.9 MPa), and 4P-BS (123 ± 32 MPa) scores were demonstrated by the samples treated with MB-mediated aPDT. However, after 12 months of storage, the highest SBS (42.3 ± 3.9 MPa) and µTBS (45.2 ± 6.6 MPa) scores were shown by samples treated with MB-mediated aPDT, while CUR-mediated aPDT treated samples demonstrated the highest 4P-BS scores (70 ± 18 MPa). Moreover, the highest antibacterial activity against S. mutans was shown by the samples treated with MB-mediated aPDT. CONCLUSIONS: The application of aPDT, especially MB-mediated, demonstrated superior SBS, µTBS, and 4P-BS values as well as antibacterial activity against S. mutans as compared to 2% CHX gel and 6% NaOCl as cavity disinfectants for IPC treatment of permanent molars.