Mutagenicity emission factors of canola oil and waste vegetable oil biodiesel: Comparison to soy biodiesel.

Canola (or rapeseed) oil and waste vegetable oil (WVO) are used commonly to make biodiesel fuels composed completely from these oils (B100) or as blends with petroleum diesel (B0). However, no studies have reported the mutagenic potencies of the particulate matter with diameter ≤2.5 µm (PM2.5) or the mutagenicity emission factors, such as revertants/MJthermal (rev/MJth) for these biodiesel emissions. Using strains TA98 and TA100 with the Salmonella (Ames) mutagenicity assay, we determined these metrics for organic extracts of PM2.5 of emissions from biodiesel containing 5% soy oil (soy B5); 5, 20, 50, and 100% canola (canola B5, B20, B50, B100), and 100% waste vegetable oil (WVO B100). The mutagenic potencies (rev/mg PM2.5) of the canola B100 and WVO B100 emissions were generally greater than those of B0, whereas the mutagenicity emission factors (rev/MJth, rev/kg fuel, and rev/m3) were less, reflecting the lower PM emissions of the biodiesels relative to B0. Nearly all the rev/mg PM2.5 and rev/MJth values were greater in TA98 with S9 than without S9, indicating a relatively greater role for polycyclic aromatic hydrocarbons, which require S9, than nitroarenes, which do not. In TA100 -S9, the rev/mg PM2.5 and rev/MJth for the biodiesels were generally ≥ to those of B0, indicating that most of these biodiesels produced more direct-acting, base-substitution mutagenic activity than did B0. For B100 biodiesels and petroleum diesel, the rev/MJth in TA98 + S9 ranked: petroleum diesel > canola > WVO > soy. The diesel emissions generally had rev/MJth values orders of magnitude higher than those of large utility-scale combustors (natural gas, coal, oil, or wood) but orders of magnitude lower than those of inefficient open burning (e.g., residential wood fireplaces). These comparative data of the potential health effects of a variety of biodiesel fuels will help inform the life-cycle assessment and use of biodiesel fuels.

Generation and characterization of diesel engine combustion emissions from petroleum diesel and soybean biodiesel fuels and application for inhalation exposure studies.

Biodiesel made from the transesterification of plant- and animal-derived oils is an important alternative fuel source for diesel engines. Although numerous studies have reported health effects associated with petroleum diesel emissions, information on biodiesel emissions are more limited. To this end, a program at the U.S. EPA assessed health effects of biodiesel emissions in rodent inhalation models. Commercially obtained soybean biodiesel (B100) and a 20% blend with petroleum diesel (B20) were compared to pure petroleum diesel (B0). Rats and mice were exposed independently for 4 h/day, 5 days/week for up to 6 weeks. Exposures were controlled by dilution air to obtain low (50 µg/m(3)), medium (150 µg/m(3)) and high (500 µg/m(3)) diesel particulate mass (PM) concentrations, and compared to filtered air. This article provides details on facilities, fuels, operating conditions, emission factors and physico-chemical characteristics of the emissions used for inhalation exposures and in vitro studies. Initial engine exhaust PM concentrations for the B100 fuel (19.7 ± 0.7 mg/m(3)) were 30% lower than those of the B0 fuel (28.0 ± 1.5 mg/m(3)). When emissions were diluted with air to control equivalent PM mass concentrations, B0 exposures had higher CO and slightly lower NO concentrations than B100. Organic/elemental carbon ratios and oxygenated methyl esters and organic acids were higher for the B100 than B0. Both the B0 and B100 fuels produced unimodal-accumulation mode particle-size distributions, with B0 producing lower concentrations of slightly larger particles. Subsequent papers in this series will describe the effects of these atmospheres on cardiopulmonary responses and in vitro genotoxicity studies.