A polymeric co-assembly of subunit vaccine with polyoxometalates induces enhanced immune responses.

Long-lasting protective immune responses are expected following vaccination. However, most vaccines alone are inability to evoke an efficient protection. The combinatory administration of adjuvants with vaccines is critical for generating the enhanced immune responses. Herein, with biocompatible poly(4-vinylpyridine) (P4VP) as template, 2.5 nm iron/molybdenum oxide cluster, {Mo72Fe30}, is applied as an adjuvant to co-assemble with antigens of Mycobacterium bovis via hydrogen bonding at molecular scale. Molecular scale integration of the antigens and {Mo72Fe30} and their full exposure to body fluid media contribute to the augmentation of both humoral and cellular immune responses of the vaccines after inoculation in mice. Anti-inflammatory factor IL-10 gradually increases after 2 weeks followed by a final back to normal level by the 5th week. The balance between proinflammatory cytokines and anti-inflammatory factors suggests that immune system can be activated in the early stage of infection by the antigens carried by the supra-particles and secrete acute inflammatory factors for host defense and antiinflammatory factors for immune protection. Electronic Supplementary Material: Supplementary material (further structural analysis and biological analsyis) is available in the online version of this article at 10.1007/s12274-021-4004-9.

3D fabrication and characterization of phosphoric acid scaffold with a HA/ß-TCP weight ratio of 60:40 for bone tissue engineering applications.

A key requirement for three-dimensional printing (3-DP) at room temperature of medical implants depends on the availability of printable and biocompatible binder-powder systems. Different concentration polyvinyl alcohol (PVA) and phosphoric acid solutions were chosen as the binders to make the artificial stent biocompatible with sufficient compressive strength. In order to achieve an optimum balance between the bioceramic powder and binder solution, the biocompatibility and mechanical properties of these artificial stent samples were tested using two kinds of binder solutions. This study demonstrated the printable binder formulation at room temperature for the 3D artificial bone scaffolds. 0.6 wt% PVA solution was ejected easily via inkjet printing, with a supplementation of 0.25 wt% Tween 80 to reduce the surface tension of the polyvinyl alcohol solution. Compared with the polyvinyl alcohol scaffolds, the phosphoric acid scaffolds had better mechanical properties. Though both scaffolds supported the cell proliferation, the absorbance of the polyvinyl alcohol scaffolds was higher than that of the phosphoric acid scaffolds. The artificial stents with a hydroxyapatite/beta-tricalcium phosphate (HA/ß-TCP) weight ratios of 60:40 depicted good biocompatibility for both scaffolds. Considering the scaffolds' mechanical and biocompatible properties, the phosphoric acid scaffolds with a HA/ß-TCP weight ratio of 60:40 may be the best combination for bone tissue engineering applications.

Molecularly imprinted solid phase extraction in a syringe filter for determination of triazine herbicides in Radix Paeoniae Alba by ultra-fast liquid chromatography.

A novel, cost-effective and simple solid phase extraction (SPE) method, by using a syringe connected with a nylon membrane filter as the adsorbent container, was developed for the extraction of triazine herbicides from Radix Paeoniae Alba (RPA) samples. The selective molecularly imprinted polymers (MIPs) synthesized with the template of atrazine were employed as the adsorbents for the enrichment and purification of analytes. The extraction parameters, including the volume and type of loading solvent, the type of washing solvent and eluting solvent, were investigated. Under the optimized conditions, the final extracts were analyzed by ultra-fast liquid chromatography (UFLC). Recoveries of the developed method range from 92.4% to 107.3% with intra- and inter-day relative standard deviations (RSDs) lower than 8.2%. The calibration curve is linear in the concentration range of 0.005-2.4 µg g(-1) for desmetryn, atrazine and terbumeton, and 0.005-1.5 µg g(-1) for dimethametryn and dipropetryn, with the correlation coefficient (R(2)) higher than 0.9995. The limits of detection (LODs) of five triazine herbicides are in the range of 0.09-0.39 ng g(-1), which are lower than the maximum residue levels (MRLs) established by various official organizations. Analytical results of three real Radix Paeoniae Alba samples indicate that the proposed method is cost-effective and easy-to-use than other routine pretreatment methods.

Magnetic ionic liquid-based dispersive liquid-liquid microextraction for the determination of triazine herbicides in vegetable oils by liquid chromatography.

Magnetic ionic liquid-based dispersive liquid-liquid microextraction (MIL-based DLLME) was developed for extracting triazine herbicides from vegetable oils. The MIL, 1-hexyl-3-methylimidazolium tetrachloroferrate ([C6mim] [FeCl4]), was used as the microextraction solvent. The magnetic separation time was shortened by simply mixing carbonyl iron powder with the MIL in the sample after DLLME. The effects of several important experimental parameters, including the amount of MIL, the time of ultrasonic extraction, the type and the volume of cleanup solvent were investigated. The MIL-based DLLME coupled with liquid chromatography gave the limits of detection of 1.31-1.49ngmL(-1) and limits of quantification of 4.33-4.91 ng mL(-1) for triazine herbicides. When the present method was applied to the analysis of vegetable oil samples, the obtained recoveries were in the range of 81.8-114.2% and the relative standard deviations were lower than 7.7%. Compared with existing methods, the performances achieved by the present method were acceptable.