Extraction of the antioxidant phytocomplex from wine-making by-products and sustainable loading in phospholipid vesicles specifically tailored for skin protection.

The present study is aimed at valorizing grape pomace, one of the most abundant winery-making by-products of the Mediterranean area, through the extraction of the main bioactive compounds from the skin of grape pomace and using them to manufacture innovative nanoformulations capable of both avoiding skin damages and promoting skincare. The phytochemicals were recovered through maceration in hydroethanolic solution. Catechin, quercetin, fisetin and gallic acid, which are known for their antioxidant power, were detected as the main compounds of the extract. Liposomes and phospholipid vesicles modified with glycerol or Montanov 82® or a combination of both, were used as carriers for the extract. The vesicles were small (~183 nm), slightly polydispersed (PI ≥ 0.28), and highly negatively charged (~-50 mV). The extract was loaded in high amounts in all vesicles (~100%) irrespective of their composition. The antioxidant activity of the extract, measured by using the DPPH (2,2-Diphenyl-1-picrylhydrazyl) test, was 84 ± 1%, and slightly increased when loaded into the vesicles (~89%, P < 0.05). The grape pomace extract loaded vesicles were highly biocompatible and able to protect fibroblasts (3T3) from the oxidative stress induced by hydrogen peroxide.

Biomass ash reutilisation as an additive in the composting process of organic fraction of municipal solid waste.

In this work the effects of selected types of biomass ash on the composting process and final product quality were studied by conducting a 96-day long experiment where the source separated organic fraction of municipal waste, mixed with wood prunings that served as bulking agent, was added with 0%, 2%, 4% and 8% wt/wt of biomass ash. The evolution over time of the main process parameters was observed, and the final composts were characterised. On the basis of the results, both the composting process and the quality of the final product were improved by ash addition. Enhanced volatile solids reduction and biological stability (up to 32% and 52%, respectively, as compared to the unamended product) were attained when ash was added, since ash favored the aerobic degradation by acting asa physical conditioner. In the final products, higher humification of organic matter (expressed in terms of the humification index, that was 2.25 times higher in the most-enriched compost than in the unamended one) and total Ca, K, Mg and P content were observed when ash was used. The latter aspect may influence the composts marketability positively, particularly with regards to potassium and phosphorus. The heavy metals content, that is regarded as the main environmental disadvantage when using ash asa composting additive, did not negatively affect the final composts quality. However, some other controversial effects of ash, related to the moisture and temperature values attained during the process, pH (8.8-9.2 as compared to 8.2 of the unamended compost) and electrical conductivity levels (up to 53% higher as compared to the unamended compost) in the final composts, were also observed.

Enhanced electrokinetic treatment of marine sediments contaminated by heavy metals and PAHs.

Dredged sediments contaminated by heavy metals and PAHs were subjected to both unenhanced and enhanced electrokinetic remediation under different operating conditions, obtained by varying the applied voltage and the type of conditioning agent used at the electrode compartments in individual experiments. While metals were not appreciably mobilized as a result of the unenhanced process, metal removal was found to be significantly improved when both the anodic and cathodic reservoirs were conditioned with the chelating agent EDTA, with removal yields ranging from 28% to 84% depending on the contaminant concerned. As for the effect on organic contaminants, under the conditions tested the electrokinetic treatment displayed a poor removal capacity towards PAHs, even when a surfactant (Tween 80) was used to promote contaminant mobilization, indicating the need for further investigation on this issue. Further research on organics removal from this type of materials through electrokinetic remediation is thus required. Furthermore, a number of technical and environmental issues will also require a careful evaluation with a view to full-scale implementation of electrokinetic sediment remediation. These include controlling side effects during the treatment (such as anodic precipitation, oxidation of the conditioning agent, and evolution of toxic gases), as well as evaluating the potential ecotoxicological effects of the chemical agents used.

Enhanced electrokinetic treatment of different marine sediments contaminated by heavy metals.

In the present work, the application of an assisted electrokinetic process for the removal of heavy metals from real contaminated sediments was investigated. The process made use of both chemical and physical methods, including addition of chelating and acid agents, as well as application of a hydraulic gradient. Lab-scale electrokinetic runs were applied on two different dredged sediments varying the applied voltage gradient and the treatment duration. The use of EDTA significantly improved the overall performance of the electrokinetic treatment for sediment V (more than 60% mobilized for each metal), while only aggressive acid conditioning with nitric acid was able to remove significant amounts of heavy metals (up to 40.5% for Pb) from sediment S due to the strong buffering capacity of this material. This clearly assesses that the specific characteristics of the materials under concern and the reactions occurring at the electrodes must be carefully evaluated when applying an electroremediation process.