Radiotherapy in the head and neck region influences the chemical and mechanical properties of intraradicular dentin.

OBJECTIVES: To investigate the chemical and mechanical properties of intraradicular dentin submitted to radiotherapy. MATERIALS AND METHODS: Sixteen mandibular incisors were divided into two groups (n = 8): non-irradiated and irradiated. The irradiated teeth were obtained from head and neck radiotherapy patients, with a total dose ranging from 70.2 to 72 Gy divided into 1.8 Gy daily. After sample preparation, intraradicular dentin slices of each root third were evaluated by Raman spectroscopy, energy dispersive spectroscopy and Knoop microhardness test. Data were analyzed by Two-way ANOVA and Tukey's test (α = 0.05). RESULTS: In Raman spectroscopy, carbonate and amide III showed a significant difference for irradiation and third (carbonate p = 0.021 and p < 0.001; amide III p < 0.001 and p = 0.001, respectively). For amide I, there was a significant difference for third (p < 0.001). For carbonate/mineral ratio, there was a significant difference for irradiation (p = 0.0016) and third (p < 0.001), with the irradiated middle third showing the lowest values. For amide I/amide III ratio, there was a significant difference for irradiation (p = 0.005) in the cervical third. In energy dispersive spectroscopy, carbon (p = 0.004; p = 0.020), phosphorus (p < 0.001; p = 0.009) and calcium (p = 0.008; p = 0.007) showed differences for irradiation and third, with the irradiated groups presenting lower values in cervical and middle thirds. For calcium/phosphorus ratio, there was a significant difference for irradiation (p < 0.001) in cervical and middle thirds. Regarding microhardness, there was a significant difference for irradiation (p < 0.001), with all irradiated groups showing lower microhardness values. CONCLUSIONS: The radiotherapy altered the chemical and mechanical properties of intraradicular dentin, mainly in the cervical and middle root thirds.

Does polishing of bleached enamel affect roughness and tooth color stability after exposure to coffee?

OBJECTIVE: This laboratory randomized study was designed to evaluate the effect of polishing on roughness and color stability of bleached teeth after coffee immersion. MATERIALS AND METHODS: Ninety bovine crowns were randomly allocated to six groups (n = 15), according to bleaching protocols: At-home: standard protocol using 10% hydrogen peroxide (HP) or In-office: standard protocol using 35% HP; and with polishing protocols: (1) no polishing, (2) bleached enamel polished with #0.5 µm or (3) #2-4 µm diamond particles grit pastes. Samples were daily immersed into coffee solution for 45 min followed by mechanical brushing simulation (30 s) for 30 days. The surface roughness (Ra) and color alteration, expressed by ΔEab , ΔE00 , and whitening index (WI) were analyzed at baseline, after bleaching/polishing protocols and after coffee solution staining. The surface from each group was examined using a scanning electron microscope. Data were analyzed by two-way repeated measure analysis of variance followed by the Tukey test (α = 0.05). RESULTS: Staining increases Ra, ΔEab , ΔE00 , and decreases WI values. Polishing after bleaching did not prevent staining, however, tooth polished with #0.5 µ-grit polishing paste showed better performance than #2-4 µ-grit (ΔEab : p = 0.001/ΔE00 : p = 0.003). Scanning electron microscope revealed a more irregular surface after coffee staining for all groups regardless bleaching/polishing protocols. CONCLUSIONS: Using #0.5 µ-grit diamond paste to polish 35%HP in-office bleached enamel reduces the roughness and tooth staining. However, polishing after 10%HP at-home bleached enamel neither affects roughness nor improves tooth color stability after exposure to coffee. CLINICAL SIGNIFICANCE: Polishing after at-home bleaching does not have benefits but after 35% hydrogen peroxide in-office bleaching, the polishing with #0.5 µ-grit polishing paste is indicated to reduce roughness and the tooth staining over time.

Can intra-radicular cleaning protocols increase the retention of fiberglass posts? A systematic review.

The presence of residues within the root canal after post-space preparation can influence the bond strength between resin cement and root dentin when using fiberglass posts (FGPs). Currently, there is no consensus in the literature regarding what is the best solution for the removal of debris after post-space preparation. This systematic review involved "in vitro" studies to investigate if cleaning methods of the root canal after post-space preparation can increase the retention of FGPs evaluated by the push-out test. Searches were carried out in PubMed (MEDLINE) and Scopus databases up to July2017. English language studies published from 2007 to July 2017 were selected. 475 studies were found, and 9 were included in this review. Information from the 9 studies were collected regarding the number of samples, storage method after extraction, root canal preparation, method of post-space preparation, endodontic sealer, resin cement, cleaning methods after post-space and presence of irrigant activation. Five studies presented the best results for the association of sodium hypochlorite (NaOCl) and ethylenediamine tetra-acetic acid (EDTA), while in the other 4 studies, the solutions that showed improved retention of FGPs were photon-induced photoacoustic streaming (PIPS), Qmix, Sikko and EDTA. The results showed heterogeneity in all comparisons due to a high variety of information about cleaning methods, different concentrations, application time, type of adhesive system and resin cements used. In conclusion, this review suggests that the use of NaOCl/EDTA results in the retention of FGPs and may thus be recommended as a post-space cleaning method influencing the luting procedure.

Can intra-radicular cleaning protocols increase the retention of fiberglass posts? A systematic review

Abstract The presence of residues within the root canal after post-space preparation can influence the bond strength between resin cement and root dentin when using fiberglass posts (FGPs). Currently, there is no consensus in the literature regarding what is the best solution for the removal of debris after post-space preparation. This systematic review involved "in vitro" studies to investigate if cleaning methods of the root canal after post-space preparation can increase the retention of FGPs evaluated by the push-out test. Searches were carried out in PubMed (MEDLINE) and Scopus databases up to July2017. English language studies published from 2007 to July 2017 were selected. 475 studies were found, and 9 were included in this review. Information from the 9 studies were collected regarding the number of samples, storage method after extraction, root canal preparation, method of post-space preparation, endodontic sealer, resin cement, cleaning methods after post-space and presence of irrigant activation. Five studies presented the best results for the association of sodium hypochlorite (NaOCl) and ethylenediamine tetra-acetic acid (EDTA), while in the other 4 studies, the solutions that showed improved retention of FGPs were photon-induced photoacoustic streaming (PIPS), Qmix, Sikko and EDTA. The results showed heterogeneity in all comparisons due to a high variety of information about cleaning methods, different concentrations, application time, type of adhesive system and resin cements used. In conclusion, this review suggests that the use of NaOCl/EDTA results in the retention of FGPs and may thus be recommended as a post-space cleaning method influencing the luting procedure.

Effect of Instrumentation Techniques, Irrigant Solutions and Artificial accelerated Aging on Fiberglass Post Bond Strength to Intraradicular Dentin.

OBJECTIVE: To evaluate the effect of instrumentation techniques, irrigant solutions and specimen aging on fiberglass posts bond strength to intraradicular dentine. MATERIALS AND METHODS: A total of 120 bovine teeth were prepared and randomized into control and experimental groups resulting from three study factors (instrumentation techniques, irrigant solutions, specimen aging). Posts were cemented with RelyX U100. Samples were submitted to push-out test and failure mode was evaluated under a confocal microscope. RESULTS: In specimens submitted to water artificial aging, nickel-titanium rotary instruments group presented higher bond strength values in apical third irrigated with NaOCl or chlorhexi-dine. Irrigation with NaOCl resulted in higher bond strength than ozonated water. Artificial aging resulted in significant bond strength increase. Adhesive cement-dentin failure was prevalent in all the groups. CONCLUSION: Root canal preparation with NiTi instruments associated with NaOCl irrigation and ethylenediaminetetra acetic acid (EDTA) increased bond strength of fiberglass posts cemented with self-adhesive resin cement to intraradicular dentine. Water artificial aging significantly increased post-Clinical significance: The understanding of factors that may influence the optimal bond between post-cement and cement-dentin are essential to the success of endodontically treated tooth restoration.

Effect of the crown, post, and remaining coronal dentin on the biomechanical behavior of endodontically treated maxillary central incisors.

STATEMENT OF PROBLEM: It is unclear how the amount of remaining coronal dentin and the type of post and core rehabilitation affect the strain, stress distribution, and fracture resistance of endodontically treated teeth. PURPOSE: The purpose of this study was to evaluate the effects of the type of post, type of crown, and the amount of remaining coronal dentin on the biomechanical behavior of endodontically treated teeth. MATERIAL AND METHODS: The investigation was conducted by using 3-dimensional finite element analysis and laboratory tests. Three-dimensional models of a maxillary central incisor were generated: without remaining coronal dentin, with 1.0 mm of remaining coronal dentin, with 2.0 mm of remaining coronal dentin, and restored with a glass-fiber post or a cast post and core in combination with a metal crown or an alumina-reinforced ceramic crown. The results were evaluated by using the von Mises criterion and Maximum Principal Stress. One hundred twenty bovine incisors were selected and divided into 12 treatment groups (n=10). Specimens were loaded at a 135-degree angle to perform strain measurements and were then loaded until fracture. The strain and fracture resistance results were analyzed with 3-way analysis of variance and the Tukey honestly significant difference test (α=.05). RESULTS: The alumina-reinforced ceramic crowns and metal crowns associated with a glass-fiber post showed a homogeneous stress distribution within the root. The cast post and core concentrated higher stresses at the post-dentin interface. Significant differences were found among the mean fracture resistance values for all groups (P<.05). The presence of 2.0 mm of coronal remnants resulted in lower strains and higher fracture resistance for both the metal and ceramic crowns. Roots restored with glass-fiber posts exhibited more favorable fractures. CONCLUSIONS: The presence of 2 mm of remaining coronal dentin improved the mechanical behavior of the endodontically treated maxillary incisors. Teeth restored with glass-fiber posts and composite resin cores showed a homogeneous stress distribution within the root dentin.

In vitro study of fracture load and fracture pattern of ceramic crowns: a finite element and fractography analysis.

PURPOSE: This in vitro study investigated the null hypothesis that metal-free crowns induce fracture loads and mechanical behavior similar to metal ceramic systems and to study the fracture pattern of ceramic crowns under compressive loads using finite element and fractography analyses. MATERIALS AND METHODS: Six groups (n = 8) with crowns from different systems were compared: conventional metal ceramic (Noritake) (CMC); modified metal ceramic (Noritake) (MMC); lithium disilicate-reinforced ceramic (IPS Empress II) (EMP); leucite-reinforced ceramic (Cergogold) (CERG); leucite fluoride-apatite reinforced ceramic (IPS d.Sign) (SIGN); and polymer crowns (Targis) (TARG). Standardized crown preparations were performed on bovine roots containing NiCr metal dowels and resin cores. Crowns were fabricated using the ceramics listed, cemented with dual-cure resin cement, and submitted to compressive loads in a mechanical testing machine at a 0.5-mm/min crosshead speed. Data were submitted to one-way ANOVA and Tukey tests, and fractured specimens were visually inspected under a stereomicroscope (20×) to determine the type of fracture. Maximum principal stress (MPS) distributions were calculated using finite element analysis, and fracture origin and the correlation with the fracture type were determined using fractography. RESULTS: Mean values of fracture resistance (N) for all groups were: CMC: 1383 ± 298 (a); MMC: 1691 ± 236 (a); EMP: 657 ± 153 (b); CERG: 546 ± 149 (bc); SIGN: 443 ± 126 (c); TARG: 749 ± 113 (b). Statistical results showed significant differences among groups (p < 0.05) represented by different lowercase letters. Metal ceramic crowns presented fracture loads significantly higher than the others. Ceramic specimens presented high incidence of fractures involving either the core or the tooth, and all fractures of polymer crown specimens involved the tooth in a catastrophic way. Based on stress and fractographic analyses it was determined that fracture occurred from the occlusal to the cervical direction. CONCLUSIONS: Within the limitations of this study, the results indicated that the use of ceramic and polymer crowns without a core reinforcement should be carefully evaluated before clinical use due to the high incidence of failure with tooth involvement. This mainly occurred for the polymer crown group, although the fracture load was higher than normal occlusal forces. High tensile stress concentrations were found around and between the occlusal loading points. Fractographic analysis indicated fracture originating from the load point and propagating from the occlusal surface toward the cervical area, which is the opposite direction of that observed in clinical situations.

The effect of post, core, crown type, and ferrule presence on the biomechanical behavior of endodontically treated bovine anterior teeth.

STATEMENT OF PROBLEM: Unresolved controversy exists concerning the remaining coronal tooth structure of anterior endodontically treated teeth and the best treatment option for restoring them. PURPOSE: The purpose of this study was to evaluate the effect of post, core, crown type, and ferrule presence on the deformation, fracture resistance, and fracture mode of endodontically treated bovine incisors. MATERIAL AND METHODS: One hundred and eighty bovine incisors were selected and divided into 12 treatment groups (n=15). The treatment variations were: with or without ferrule, restored with cast post and core, glass fiber post with composite resin core, or glass fiber post with fiber-reinforced core, and metal- or alumina-reinforced ceramic crown (n=15). The restored incisors were loaded at a 135-degree angle, and the deformation was measured using strain gauges placed on the buccal and proximal root surfaces. Specimens were subsequently loaded to the point of fracture. Strain and fracture resistance results were analyzed by 3-way ANOVA and Tukey HSD tests (α=.05). RESULTS: Ferrule presence did not significantly influence the buccal strain and fracture resistance for the ceramic crown groups, irrespective of core and crown type. Ferrule presence resulted in lower strains and higher fracture resistance in the metal crown groups, irrespective of core. The cast post and core showed lower strain values than groups with glass fiber posts when restored with metal crowns. CONCLUSIONS: Core type did not affect the deformation and fracture resistance of endodontically treated incisors restored with alumina-reinforced ceramic crowns. The presence of a ferrule improved the mechanical behavior of teeth restored with metal crowns, irrespective of core type.

Mechanical and acid root treatment on periodontally affected human teeth: a scanning electronic microscopy

Aim: To evaluate the root topography of human teeth affected by periodontitis, after different root surface treatments. Methods: Forty-two periodontally affected single-rooted human teeth were selected and randomly divided into 7 groups (n=6): Cont- control group, which received no treatment; Sca- root surface scaling and root planning with curettes; ScaPh- Sca followed by 37%phosphoric acid gel etching for 15 s; ScaEdta- Sca followed by 24% EDTA gel pH 7 for 1 min; ScaCi- Sca followed by 30% citric acid pH 1.6 for 5 min; ScaTe- Sca followed by - mixture obtained by 500 mg tetracycline capsule dissolved in saline solution for 3 min; ScaTeg- Sca followed by 0.2 g/mL tetracycline gel pH 1.8 for 1 min. The specimens were analyzed by scanning electronic microscopy to verify the presence of calculus, demineralization level and residues of the product. Results: Calculus deposits were found in all control specimens. ScaEdta, ScaCi and ScaTeg removed completely calculus deposits and resulted in adequate demineralization without smear layer and smear plug on root surface. ScaTe produced great tetracycline residues with several demineralization areas on root dentin surface. Conclusions: ScaEdta, ScaCi and ScaTeg produced clean root surfaces associated with regular dentin demineralization.

Influence of airborne-particle abrasion on mechanical properties and bond strength of carbon/epoxy and glass/bis-GMA fiber-reinforced resin posts.

STATEMENT OF PROBLEM: Controversy exists concerning the use of fiber-reinforced posts to improve bond strength to resin cement because some precementation treatments can compromise the mechanical properties of the posts. PURPOSE: The purpose of this study was to analyze the influence of airborne-particle abrasion on the mechanical properties and microtensile bond strength (MTBS) of carbon/epoxy and glass/bis-GMA fiber-reinforced resin posts. MATERIAL AND METHODS: Flexural strength (delta(f)), flexural modulus (E(f)), and stiffness (S) were assessed using a 3-point bending test for glass fiber-reinforced and carbon fiber-reinforced resin posts submitted to airborne-particle abrasion (AB) with 50-microm Al(2)O(3), and for posts without any surface treatment (controls) (n=10). Forty glass fiber (GF) and 40 carbon fiber (CF) posts were submitted to 1 of 4 surface treatments (n=10) prior to MTBS testing: silane (S); silane and adhesive (SA); airborne-particle abrasion with 50-microm Al(2)O(3) and silane (ABS); airborne-particle abrasion, silane, and adhesive (ABSA). Two composite resin restorations (Filtek Z250) with rounded depressions in the lateral face were bilaterally fixed to the post with resin cement (RelyX ARC). Next, the specimen was sectioned with a precision saw running perpendicular to the bonded surface to obtain 10 bonded beam specimens with a cross-sectional area of 1 mm(2). Each beam specimen was tested in a mechanical testing machine (EMIC 2,000 DL), under stress, at a crosshead speed of 0.5 mm/min until failure. Data were analyzed by 2-way ANOVA followed by Tukey HSD test (alpha=.05). Failure patterns of tested specimens were analyzed using scanning electron microscopy (SEM). RESULTS: The 3-point bending test demonstrated significant differences among groups only for the post type factor for flexural strength, flexural modulus, and stiffness. The carbon fiber posts exhibited significantly higher mean flexural strength (P=.001), flexural modulus (P=.003), and stiffness (P=.001) values when compared with glass fiber posts, irrespective of surface treatment. An alteration in the superficial structure of the posts could be observed by SEM after airborne-particle abrasion. MTBS testing showed no significant effect for the surface treatment type; however, significant effects for post system factor and for interaction between the 2 factors were observed. For the carbon fiber post, the ABSA surface treatment resulted in values significantly lower than the S surface treatment. SEM analysis of MTBS-tested specimens demonstrated adhesive and cohesive failures. CONCLUSIONS: Airborne-particle abrasion did not influence the mechanical properties of the post; however, it produced undesirable surface changes, which could reduce the bond strength to resin cement. For the surface treatments studied, if silane is applied, the adhesive system and airborne-particle abrasion are not necessary.

Efeito de diferentes tratamentos do substrato dental na resistência adesiva e fixação de restaurações indiretas associada a adesivo auto-condicionante / Effect of different treatments of the dental substrate on the ultimate bond strength of indirect restorations associated to a self-etching adhesive

Este trabalho avaliou a resistência adesiva (µTBS) na fixação de restaurações indiretas por meio de cimento resinoso e adesivo auto-condicionante sob influência de diferentes tratamentos prévios de esmalte e dentina. Trinta incisivos bovinos foram extraídos e tiveram suas raízes cortadas na junção cemento-esmalte. A superfície vestibular dos dentes foi lixada até exposição de dentina superficial, padronizando a formação de smear layer. As amostras foram divididas aleatoriamente em três grupos (n=10): G1: aplicação do adesivo auto-condicionante One up Bond F (OB), seguindo as instruções do fabricante; G2:condicionamento com ácido fosfórico à 37% em esmalte e dentina seguindo aplicação de (OB); G3: jateamento com óxido de alumínio 50µm em esmalte e dentina previamente à aplicação de (OB). Restaurações indiretas com resina composta foram fixadas usando cimento resinoso dual e as amostras foram cortadas com área adesiva de aproximadamente 1,0 mm² em três regiões: esmalte (E), dentina periférica (DP) e dentina central (DC). Foram submetidas a ensaio de microtração em máquina de ensaio mecânico em velocidade de 0,5mm/min. Após fratura, as amostras foram analisadas em Microscopia Eletrônica de Varredura (MEV) para avaliação do padrão de fratura. Os valores de (µTBS) foram expressos em MPa e os dados foram analisados em ANOVA seguido por teste Tukey (p<0,05). Os resultados foram: E/G2: 30,4±11,9a; E/G3: 16,0±8,9b; E/G1: 15,8±5,8b; DP/G1: 24,2±12,1a; DP/G3: 15,2±7,1b; DP/G2: 15,0±9,8b; DC/G1: 17,3±10,4a; DC/G3: 11,6±3,5b; DC/G2: 11,4±5,2b. O jateamento não aumentos os valores de (µTBS). O prévio condicionamento ácido aumentou a resistência adesiva em esmalte e diminuiu em dentina.

Surface treatment protocols in the cementation process of ceramic and laboratory-processed composite restorations: a literature review.

UNLABELLED: The clinical longevity of indirect restorations made of ceramics or indirect composite resins depends on their successful treatment and cementation. The cementation technique is determined by the type of restorative material-ceramics or indirect composite resins; thus, their intaglio surface treatment should be performed according to their particular compositions. The aim of this literature review was to define surface treatment protocols of different esthetic indirect restorative materials. A PubMed database search was conducted for in vitro studies pertaining to the most common treatment protocols of tooth-colored materials. Articles that described at least the surface treatment procedure, its effects on adhesion, its relationship with the material's composition, clinical aspects, and expected longevity were selected. The search was limited to peer-reviewed articles published in English between 1965 and 2004 in dental journals. Sandblasting, etching techniques, and silane coupling agents are the most common procedures with improved results. CLINICAL SIGNIFICANCE: Tooth-colored restorative materials vary considerably in composition and require different protocols for adhesive cementation.