Fabrication of amino- and hydroxyl dual-functionalized magnetic microporous organic network for extraction of zearalenone from traditional Chinese medicine prior to the HPLC determination.

Efficient enrichment of trace zearalenone (ZEN) from the complex traditional Chinese medicine (TCM) samples is quite difficult, but of great significance for TCM quality control. Herein, we reported a novel magnetic solid phase extraction (MSPE) strategy for ZEN enrichment using the amino- and hydroxyl dual-functionalized magnetic microporous organic network (Fe3O4@MON-NH2-OH) as an advanced adsorbent combined with the high-performance liquid chromatography (HPLC) determination. Efficient extraction of ZEN was achieved via the possible hydrogen bonding, hydrophobic, and π-π interactions between Fe3O4@MON-NH2-OH and ZEN. The adsorption capacity of Fe3O4@MON-NH2-OH for ZEN was 215.0 mg g-1 at the room temperature, which was much higher than most of the reported adsorbents. Under the optimal condition, the developed Fe3O4@MON-NH2-OH-MSPE-HPLC method exhibited wide linear range (5-2500 µg L-1), low limits of detection (1.4-35 µg L-1), less adsorbent consumption (5 mg), and large enhancement factor (95) for ZEN. The proposed method was successfully applied to detect trace ZEN from 10 kinds of real TCM samples. Conclusively, this work demonstrates the Fe3O4@MON-NH2-OH can effectively extract trace ZEN from the complex TCM matrices, which may open up a new way for the application of MONs in the enrichment and extraction of trace contaminants or active constituents from the complex TCM samples.

Selective Removal of Chlorophyll and Isolation of Lutein from Plant Extracts Using Magnetic Solid Phase Extraction with Iron Oxide Nanoparticles.

In recent years, there has been a growing interest in plant pigments as readily available nutraceuticals. Photosynthetic pigments, specifically chlorophylls and carotenoids, renowned for their non-toxic antioxidant properties, are increasingly finding applications beyond their health-promoting attributes. Consequently, there is an ongoing need for cost-effective methods of isolation. This study employs a co-precipitation method to synthesize magnetic iron oxide nanoparticles. Scanning electron microscopy (SEM) coupled with energy dispersive spectrometry (EDS) confirms that an aqueous environment and oxidizing conditions yield nanosized iron oxide with particle sizes ranging from 80 to 140 nm. X-ray photoelectron spectroscopy (XPS) spectra indicate the presence of hydrous iron oxide FeO(OH) on the surface of the nanosized iron oxide. The Brunauer-Emmett-Teller (BET) surface area of obtained nanomaterial was 151.4 m2 g-1, with total pore volumes of pores 0.25 cm3 g-1 STP. The material, designated as iron oxide nanoparticles (IONPs), serves as an adsorbent for magnetic solid phase extraction (MSPE) and isolation of photosynthetic pigments (chlorophyll a, lutein) from extracts of higher green plants (Mentha piperita L., Urtica dioica L.). Sorption of chlorophyll a onto the nanoparticles is confirmed using UV-vis spectroscopy, Fourier transform infrared photoacoustic spectroscopy (FT-IR/PAS), and high-performance liquid chromatography (HPLC). Selective sorption of chlorophyll a requires a minimum of 3 g of IONPs per 12 mg of chlorophyll a, with acetone as the solvent, and is dependent on a storage time of 48 h. Extended contact time of IONPs with the acetone extract, i.e., 72 h, ensures the elimination of remaining components except lutein, with a spectral purity of 98%, recovered with over 90% efficiency. The mechanism of chlorophyll removal using IONPs relies on the interaction of the pigment's carbonyl (C=O) groups with the adsorbent surface hydroxyl (-OH) groups. Based on molecular dynamics (MD) simulations, it has been proven that the selective adsorption of pigments is also influenced by more favorable dispersion interactions between acetone and chlorophyll in comparison with other solutes. An aqueous environment significantly promotes the removal of pigments; however, it results in a complete loss of selectivity.

High-throughput extraction and automatic purification of alternariol from edible and medicinal herbs based on aptamer-functionalized magnetic nanoparticles.

Mycotoxin contamination is widespread in plants and herbs, posing serious threats to the consumer and human health. Of them, alternariol (AOH) has attracted great attention as an "emerging" mycotoxin in medicinal herbs. However, a specific and high-throughput extraction method for AOH is currently lacking. Thus, developing an efficient pre-treatment technique for AOH detection is extremely vital. Here, a novel automated magnetic solid-phase extraction method was proposed for the highly efficient extraction of AOH. Combining the aptamer-functionalized magnetic nanoparticles (AMNPs) and the automatic purification instrument, AOH could be extracted in medicinal herbs in high throughput (20 samples) and a short time (30 min). The main parameters affecting extraction were optimized, and the method was finally carried out by incubation AMNPs with 3 mL of sample solution for 10 min, and then desorption in 75% methanol for liquid-phase detection. Under optimal conditions, good reproducibility, stability, and selectivity were realized with an adsorption capacity of 550.84 ng/mg. AOH extraction in three edible herbs showed good resistance to matrix interference with recovery rates from 86% to 111%. In combination with AMNPs and the automatic purification instrument, high-throughput and labor-free extraction of AOH in different complex matrices was achieved, which could be extended in other complex matrices.

High enrichment and sensitive measurement of oxytetracycline in tea drinks by thermosensitive magnetic molecular imprinting based magnetic solid phase extraction coupled with boron doped carbon dots.

As a typical kind of new pollutants, there are still some challenges in the rapid detection of antibiotics. In this work, a sensitive fluorescent probe based on boron-doped carbon dots (B-CDs) in combination with thermo-responsive magnetic molecularly imprinted polymers (T-MMIPs) was constructed for the detection of oxytetracycline (OTC) in tea drinks. T-MMIPs were designed, fabricated and employed to enrich OTC at trace level from tea drinks, and B-CDs were utilized as the fluorescent probe to detect the concentration of OTC. The proposed method exhibited good linear relationship with OTC concentration from 0.2 to 60 µg L-1 and the limit of detection was 0.1 µg L-1. The established method has been successfully validated with tea beverages. Present work was the first attempt application of T-MMIPs in combination with CDs in detection of OTC, and demonstrated that the proposed method endowed the detection of OTC with high selectivity, sensitivity, reliability and wide application prospect, meanwhile offered a new strategy for the method establishment of rapid and sensitive detection of trace antibiotics in food and other matrices.

A novel deep eutectic solvent modified magnetic covalent organic framework for the selective separation and determination of trace copper ion in medicinal plants and environmental samples.

BACKGROUND: Pretreatment techniques should be introduced before metal ion determination because there is very low content of heavy metals in Chinese medicinal plants and environmental samples. Magnetic dispersive micro solid phase extraction (MDMSPE) has been widely used for the separation and adsorption of heavy metal pollutants in medicinal plants and environmental samples. However, the majority of MDMSPE adsorbents have certain drawbacks, including low selectivity, poor anti-interference ability, and small adsorption capacity. Therefore, modifying currently available adsorption materials has gained attention in research. RESULTS: In this study, a novel adsorbent MCOF-DES based on a magnetic covalent organic framework (MCOF) modified by a new deep eutectic solvent (DES) was synthesized for the first time and used as an adsorbent of MDMSPE. The MDMSPE was combined with inductively coupled plasma optical emission spectrometry (ICP-OES) for selective separation, enrichment, and accurate determination of trace copper ion (Cu2+) in medicinal plants and environmental samples. Various characterization results show the successful preparation of new MCOF-DES. Under the optimal conditions, the enrichment factor (EF) of Cu2+ was 30, the limit of detection (LOD) was 0.16 µg L-1, and the limit of quantitation (LOQ) was 0.54 µg L-1. The results for the determination of Cu2+ were highly consistent with those of inductively coupled plasma mass spectrometry (ICP-MS), which verified the accuracy and reliability of the method. SIGNIFICANCE: The established method based on a new adsorption material MCOF-DES has achieved the selective separation and determination of trace Cu2+ in medicinal and edible homologous medicinal materials (Phyllanthus emblica Linn.) and environmental samples (soil and water), which provides a promising, selective, and sensitive approach for the determination of trace Cu2+ in other real samples.

Fabrication of a bio-based polymer adsorbent and its application for extraction and determination of glycosides from Huangqi Liuyi decoction.

Huangqi Liuyi Decoction, a famous classical Chinese prescription, shows significant curative effect on diabetes and its complications, in which calycosin-7-glucoside, liquiritin and glycyrrhizic acid are the main components that playing these mentioned pharmacological activity, under the synergistic action of various other ingredients in the decoction. However, there are significant differences in the content of active compounds in Chinese medicinal materials, which mainly due to origin, picking seasons, and processing methods. Hence, the accurate content of the glycosides is the prerequisite for ensuring the pharmacological efficacy. Aiming at establishing an efficient extraction and determination method for accurate quantitative analysis of calycosin-7-glucoside, liquiritin and glycyrrhizic acid in Huangqi Liuyi Decoction, an on line solid-phase extraction-high-performance liquid chromatography method was developed, using a homemade bio-based monolithic adsorbent. The bio-based adsorbent was prepared in a stainless steel tube, using bio-monomers of methyleugenol and S-allyl-L-cysteine, which effectively reduced the dependence of the polymer field on non-renewable fossil resources and reduced carbon emissions. Furthermore, the prepared adsorbent owned abundant chemical groups, which can produce interactions of hydrogen bond, dipole-dipole, π-π and hydrophobic force with the target glycosides, thus improving the specific recognition ability of the adsorbent. The experiments were carried out on an LC-3000 HPLC instrument with a six-way valve. Methodology validation indicates that the recovery is in the range of 97.0%-103.4% with the RSD in the range of 1.6%-4.0%, due to the specific selectivity of the bio-based monolithic adsorbent for these three glycosides, and good matrix-removal ability for Huangqi Liuyi decoction. The limit of detection is 0.17, 0.50 and 0.33 µg/mL for calycosin-7-glucoside, liquiritin and glycyrrhizic acid, respectively, and the limit of quantitation is 0.50, 1.50 and 1.00 µg/mL, respectively, with the linear range of 2-200 µg/mL for calycosin-7-glucoside, and 5-500 µg/mL for liquiritin and glycyrrhizic acid. The present work provided a simple and efficient method for the extraction and determination of glycosides in complex medicinal plants.

In situ growth of ZIF-67 to construct core-shell mosaic structural composites for efficient extraction of benzoylurea insecticides.

A novel mosaic structure Silica@C/Co@ZIF-67 composite was synthesized by successfully embedding Co nanoparticles on the surface of silica spheres with the help of thermoplastic polyethyleneimine by carbon-reduction. The ZIF-67 half-shell layer structure was synthesized by the in-situ growth of ZIF-67 on the surface of silica spheres through the coordination of 2-methylimidazole with Co metal nodes. The composite was used as a magnetic solid-phase extraction adsorbent combined with high performance liquid chromatography-ultraviolet detector (HPLC-UV) for the extraction and determination of benzoylurea insecticides (BUs) in vegetables and tea. Based on the presence of π-π, hydrophobic and hydrogen bonding interactions between Silica@C/Co@ZIF-67 and BUs, the BUs were rapidly captured by the composites resulting in high adsorption performance. Under the optimal extraction parameters, the linear ranges were 0.3-200 µg L-1 for diflubenzuron, 0.6-200 µg L-1 for chlorbenzuron, and 1.0-200 µg L-1 for triflumuron, teflubenzuron, and flufenoxuron, with correlation coefficients (R2) greater than 0.9991. The limits of detection (LODs) of the method were 0.1-0.3 µg L-1, and the relative standard deviations (RSDs) were 1.2-3.0% for intra-day and 2.6-4.6% for inter-day. In the spiked recovery experiments of vegetables and tea, the recoveries of the five kinds of BUs ranged from 75.8 to 112.9%. In addition, after 10 repetitions using Silica@C/Co@ZIF-67, the recoveries of the five kinds of BUs were still as high as 78.4 to 83.9%.

Preparation of a novel MOF-POPM and its application in online purification and enrichment of oleanolic acid in medicinal plants.

In present work, a method for enrichment, purification, and content determination of oleanolic acid (OA) in medicinal plants was established based on on-line solid phase extraction (SPE). A metal organic frameworks-porous organic polymer monolith (MOF-POPM) was prepared with functionalized UiO-66-(OH)2 as monomer and was used as SPE column for online enrichment and purification of OA. The ratio of adsorbent, enriching and eluting solvent, mobile phase pH, and flow rate had been systematically investigated. Under the optimum conditions, the linear range of OA was 0.59-2500 µg/mL with r = 0.9996. The limit of detection (LOD) was 0.18 µg/mL and the limit of quantification (LOQ) was 0.59 µg/mL. The intra-day relative standard deviations (RSDs) and inter-day RSDs of retention time and peak area were less than 0.3% and 1.3%, respectively. The average recoveries of OA in medicinal plants samples ranged from 87.7 to 104.6%. The results demonstrated that the online system was reliable and accurate for enrichment, purification, and content determination of OA in medicinal plants.

Single injection by LC-ESI-MS/MS for simultaneous determination of organophosphate tri- and di-esters in plant tissue based on ultrasonic-assisted sequential extraction and single-step purification.

A novel methodology based on ultrasonic-assisted sequential extraction, dispersive-SPE purification, and single-injection on liquid chromatography-tandem mass spectrometry (LC-MS/MS) is proposed, for the first time, to simultaneously measure 14 tri-OPEs and 9 di-OPEs in plant tissues. The samples were successively ultrasonicated with a mixture of hexane:dichloromethane (1:1, v/v) and 8% acetic acid in acetonitrile for extracting tri- and di-OPEs purified with graphitized carbon black and quantitated on LC-MS/MS at the same time. The recoveries of targeted tri- and di-OPEs in the matrix spike ranged from 66% to 120% and 71% to 110% respectively. The proposed method was validated by processing eight types of common vegetables including spinach (Spinacia oleracea L.), lettuce (Lactuca sativa), carrot (Daucus carota var. sativa Hoffm.), sweet potato (Solanum tuberosum L.), cucumber (Cucumis sativus L.), tomato (Solanum lycopersicum L.), green beans (Phaseolus vulgaris), and cowpeas (Vigna unguiculata), with the recoveries of surrogates ranging from 84% to 98%.

Design and Optimisation of Sustainable Sample Treatments Based on Ultrasound-Assisted Extraction and Strong Cation-Exchange Purification with Functionalised SBA-15 for Opium Alkaloids in Ground Poppy Seeds.

An analysis methodology was optimised and validated for the quantification of opium alkaloids (OAs) in ground poppy seeds. This involved ultrasound-assisted extraction (UAE) and solid-phase extraction (SPE) purification before analysis using a high-performance liquid chromatography mass spectrometry detector (HPLC-MS/MS). UAE was optimised through the design of experiments with three factors and a three-level full factorial design. For SPE optimisation, a commercial material was compared with a previously synthesised material of SBA-15 silica functionalised with sulfonic groups (SBA-15-SO3-). The synthesised material demonstrated superior efficiency with only 25 mg and proved to be reusable for up to four cycles. The methodology was properly validated in terms of linearity, limits of detection and quantification, and selectivity. Matrix effects were negligible; adequate recovery values (85-100%) and inter-day and intra-day precision (≤15%) were obtained. The greenness of the method was evaluated with the AGREEprep metric scale, being more environmentally friendly compared to OA analysis methods. Finally, the method was applied to different samples of ground poppy seeds and revealed a concentration of 140 mg/kg of morphine equivalents in one of the samples, surpassing the legislatively established limits by sevenfold. This highlights the need to analyse these types of samples to mitigate potential public health issues.

Synthesis of composite materials combining magnetic metal-organic frameworks and conjugated organic frameworks for selective extraction of carbendazim and thiabendazole residues from Chinese herbal medicine samples.

A magnetic metal-organic framework MIL-68(Al) and a covalent organic framework were used as magnetic solid-phase extraction (MSPE) adsorbents in combination with high-performance liquid chromatography ultraviolet detection (HPLC-UV) to detect carbendazim (CBZ) and thiabendazole (TBZ). The main parameters affecting the extraction in the MSPE process were studied and optimized. Fe3O4@MIL-68(Al) coated with 1,3,5-tris(4-aminophenyl)benzene and terephthaldehyde (Fe3O4@MIL-68(Al)@TAPB-PDA-COF) was analyzed and verified. The material was proven to be suitable for adsorbing CBZ and TBZ. Various adsorption models were used to study its adsorption mechanism. The adsorption results were in good agreement with the pseudo-second-order kinetic model and Langmuir isotherm model. The maximum adsorption capacities of Fe3O4@MIL-68(Al)@TAPB-PDA-COF over CBZ and TBZ were 54.24 and 67.87 mg g-1, respectively, and the equilibrium adsorption time was 200 min. Fe3O4@MIL-68(Al)@TAPB-PDA-COF with excellent recyclability showed higher adsorption capacity and selectivity. A method based on Fe3O4@MIL-68(Al)@TAPB-PDA-COF combined with HPLC-UV was established under the optimal extraction conditions and used to separate and detect trace imidazole drugs in Chinese herbal samples, achieving a low limit of detection (0.65-1.30 µg L-1) with excellent linear correlation (r > 0.999). The recovery rate and relative standard deviation were 86.05-99.78 % and 0.15-4.90 %, respectively. Therefore, the Fe3O4@MIL-68@TAPB-PDA-COF can be regarded as an effective adsorbent for the pretreatment of CBZ and TBZ drugs in Chinese herbal samples.

Preparation of COF-coated nickel foam adsorbents for dispersive solid-phase extraction of 16 polycyclic aromatic hydrocarbons from Chinese herbal medicines.

Covalent organic framework coated nickel foam (NF@COF) was prepared as a sorbent for the dispersive solid phase extraction (DSPE) of polycyclic aromatic hydrocarbons (PAHs) from Chinese herbal medicines (CHMs) prior to their determination by gas chromatography-mass spectrometry (GC-MS). The structure and morphology of the as-synthesized NF@COF were characterized by different techniques. Various key parameters affecting the performance of the DSPE method, including the amount of sorbent, desorption solvent, desorption volume and time, extraction time, and sample volume, were investigated. Under the optimized conditions, NF@COF combined with GC-MS was successfully applied to the determination of 16 PAHs in CHMs. The method showed wide linearity (20-2000 ng mL-1), low limits of determination (0.3-2.7 ng mL-1), and high recoveries (78.0-124%). These results revealed that NF@COF has the potential for efficient extraction of PAHs from complex samples.

A simple microwave-assisted synthesis of cobalt ferrite nanoparticles and its application for the determination of lead ions in rooibos (Aspalathus linearis) tea.

In this study, a magnetic sorbent assisted dispersive solid phase extraction (DSPE) method was used to preconcentrate lead ions from rooibos tea samples for determination by slotted quartz tube-flame atomic absorption spectrometry (SQT-FAAS). Cobalt ferrite magnetic nanoparticles (CoFe2O4 MNPs) were synthesized by microwave assisted digestion. Limits of detection and quantification were calculated as 5.3 and 17.6 µg/L, respectively, in a linear dynamic range of 20-800 µg/L. The enhancement factor of the developed method was found to be 80-folds when compared to the detection limit of the regular FAAS system. The percent recoveries obtained for rooibos tea samples spiked at different concentrations were in the range of 77 - 125%, with high repeatability as indicated by low standard deviations. The findings of the study demonstrated that the CoFe2O4 MNPs-based extraction method is a straightforward, fast, affordable, safe, and eco-friendly approach to qualifying/quantifying lead with high precision in the selected beverage sample.

Determination of tolfenpyrad residues in green tea by GC-MS/MS based on acetonitrile extractant, dispersion solid phase extraction purification.

Green tea is one of people's favorite drinks. However, pesticide residues in green tea can cause harm to the human body, and therefore, detection of pesticide residues in green tea is very important. In recent years, the detection of pesticide residues in tea has become a research hotspot. In this paper, a gas chromatography-mass spectrometry/mass spectrometry (GC-MS/MS) detection method of tolfenpyrad pesticide residues in green tea was established by using acetonitrile extractant, dispersive solid-phase extraction purification, temperature programming and application retention time lock with the database. After the sample was extracted with acetonitrile, then the sample was purified by QuEChERS extraction purification tube, afterward isomer B was used as the internal standard for the determination by multiple reaction monitoring mode (MRM) of GC-MS/MS. The results indicated that the experimental data accorded with the criterion on quality control of laboratoris(chemical testing of food), and the requirements of recovery, calibration curve, precision.This method was used to detect tolfenpyrad residues in actual green tea samples in multiple batches, and the satisfactory results were obtained.

The Selective Separation of Carnosic Acid and Rosmarinic Acid by Solid-Phase Extraction and Liquid-Liquid Extraction: A Comparative Study.

Rosmarinus officinalis leaves (ROLs) are widely used in the food and cosmetics industries due to their high antioxidant activity and fascinating flavor properties. Carnosic acid (CA) and rosmarinic acid (RA) are regarded as the characteristic antioxidant components of ROLs, and the selective separation of CA and RA remains a significant challenge. In this work, the feasibility of achieving the selective separation of CA and RA from ROLs by solid-phase extraction (SPE) and liquid-liquid extraction (LLE) was studied and compared. The experiments suggested that SPE with CAD-40 macroporous resin as the adsorbent was a good choice for selectively isolating CA from the extracts of ROLs and could produce raw CA with purity levels as high as 76.5%. The LLE with ethyl acetate (EA) as the extraction solvent was more suitable for extracting RA from the diluted extracts of ROLs and could produce raw RA with a purity level of 56.3%. Compared with the reported column chromatography and LLE techniques, the developed SPE-LLE method not only exhibited higher extraction efficiency for CA and RA, but can also produce CA and RA with higher purity.

Is alumina suitable for solid phase extraction of catecholamines from brain tissue?

Occupational and environmental toxicology specialists find catecholamine fluctuations in brain tissue relevant for research of neurotoxicity, such as that induced by manganese or zinc, pesticides, industrial solvents, plastic, air pollution, or irradiation. Considering that catecholamine tissue concentrations are generally very low, their extraction requires a reliable and optimal method that will achieve maximum recovery and minimise other interferences. This study aimed to evaluate whether the aluminium (III) oxide (Al2O3, alumina) based cartridges designed for catecholamine isolation from plasma could be used for solid-phase extraction (SPE) of catecholamine from the brain tissue. To do that, we homogenised Wistar rat brain tissue with perchloric acid and compared three extraction techniques: SPE, the routine filtration through a 0.22 µm membrane filter, and their combination. In the extracts, we compared relative chromatographic catecholamine mobility measured with high performance liquid chromatography with electrochemical detection. Chromatographic patterns for norepinephrine and epinephrine were similar regardless of the extraction technique, which indicates that the alumina cartridge is good enough to isolate them from brain tissue. However, the dopamine pattern was unsatisfactory, and further experiments are needed to identify the issue and optimise the protocol.

Phenylboronic acid-functionalized magnetic metal-organic framework nanoparticles for magnetic solid phase extraction of five benzoylurea insecticides.

This research involves the construction of a phenylboronic acid-functionalized magnetic UiO-66 metal-organic framework (MOF) nanoparticle (CPBA@UiO-66@Fe3O4). Its design is primarily for the magnetic solid phase extraction (MSPE) of benzoylurea insecticides. An organic ligand, 2-amino terephthalic acid (2-ATPA), facilitated the introduction of amino groups while keeping the original crystal structure of UiO-66 intact. The constructed UiO-66 MOF showcases a porous structure and extensive surface area, thereby providing an optimal platform for further functionalization. The employment of 4-carboxylphenylboronic acid as a modifier notably amplified the extraction efficiency for benzoylureas. This improvement was due to the formation of B-N coordination and other secondary interactions. By integrating this with high-performance liquid chromatography (HPLC), we established a quantitative analytical method for benzoylurea insecticides. This method achieved a wide linear range (2.5-500 µg L-1 or 5-500 µg L-1), satisfactory recoveries (83.3-95.1%), and acceptable limits of detection (LODs: 0.3-1.0 µg L-1). The developed method proved successful when applied to six tea infusion samples, representing China's six major tea categories. Semi-fermented and light-fermented tea samples demonstrated relatively higher spiking recoveries.

Dispersive solid-phase extraction of alkaloids and polyphenols using borate hypercrosslinked polymers.

In this study, a borate hyper-crosslinked polymer was synthesized by crosslinking 1-naphthalene boric acid and dimethoxymethane via the Friedel-Crafts reaction. The prepared polymer exhibits excellent adsorption performance toward alkaloids and polyphenols with maximum adsorption capacities ranging from 25.07 to 39.60 mg/g. Adsorption kinetics and isotherms model results indicated the adsorption was a monolayer and chemical process. Under the optimal extraction conditions, a sensitive method was established for the simultaneous quantification of alkaloids and polyphenols in green tea and Coptis chinensis by coupling with the proposed sorbent and ultra-high performance liquid chromatography detection. The proposed method exhibited a wide linear range of 5.0-5000.0 ng/ml with R2 ≥ 0.99, a low limit of detection (0.66-11.25 ng/ml), and satisfactory recoveries (81.2%-117.4%). This work provides a simple and convenient candidate for the sensitive determination of alkaloids and polyphenols in green tea and complex herbal products.

Determination of polycyclic aromatic hydrocarbons in Chinese herbal medicines by gas chromatography-mass spectrometry with graphene-functionalized nickel foam.

Graphene-functionalized nickel foam (NF) sorbent materials were prepared and characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and Thermogravimetric analysis. For the separation and detection of polycyclic aromatic hydrocarbons (PAHs) in five Chinese medicine samples, namely dandelion, fructus aurantii, peppermint, mulberry leaf and embryo chrysanthemum, a method combining dispersive micro-solid phase extraction and gas chromatography-mass spectrometry (GC-MS) was developed. Four conditions affecting the extraction efficiency, such as the type of desorption solvent, the amount of sorbent, the extraction time and the volume of water sample, were optimized. The results of the methodological validation showed that NF@SiO2@G was able to adsorb PAHs well and with good reproducibility. All analytes showed good linearity in the concentration range of 20-2000 ng/mL with coefficient of determination R2≥0.9956. The limit of detection was 0.98-13.34 ng/mL, and the limit of quantification ranged from 3.25 to 44.47 ng/mL. Both the intra-day and inter-day precision were lower than 15.46%, and the spiked recoveries were in the range of 75.5-118.4%. The total contents of the 16 PAHs contained in these five Chinese herbal medicines (CHMs) were varied from 450 to 1557 µg/kg. The results indicated that the graphene-functionalized NF sorbent combined with GC-MS can effectively detect PAHs in CHMs.

A sensitive, robust and high-throughput isotope dilution LC-MS/MS method for quantifying three folate forms in serum.

This study aimed to establish an isotope dilution LC-MS/MS method for the determination of folic acid, 5-formyltetrahydrofolate and 5-methyltetrahydrofolate in human serum. This method was then used to quantify these three folate forms in the healthy adult population and supplement users. A stable 96-well solid-phase extraction system was used to prepare serum samples. The highly sensitive method was established using a Shimadzu LCMS-8060NX. The linearity was good in the range of 0.1-10 nmol/l for folic acid and 5-formyltetrahydrofolate and 1.0-100 nmol/l for 5-methyltetrahydrofolate. The accuracy and precision were good. The method was sensitive, robust and high-throughput and could be used for the routine clinical monitoring of these three folate forms in the Chinese population.