Role of plasma process gas on permeate flux augmentation of cellulose nitrate membrane for mud water treatment.

A comparative study between Nitrogen (N2) and Argon (Ar) plasma is carried out to investigate its effect on surface morphology, hydrophilicity, permeate flux and ageing of cellulose nitrate polymeric membranes in the present work. Langmuir probe and Optical Emission Spectroscopy are used to characterize the plasma. The SEM analysis reveals the noticeable macro-void creations and pore enlargement for both N2 and Ar plasma. The AFM analysis shows a higher surface roughness for Ar plasma treatment as compared to N2 plasma treatment. XPS analysis confirms the changes in the polymer matrix along with the incorporation of various functional groups on the membrane surface as a result of the plasma treatment. A better hydrophilic nature with prolonged plasma treatment is observed for Ar plasma as compared to N2 plasma treatment. The present results show a higher permeate flux with a high rejection rate for Ar plasma treatment in comparison to N2 plasma, which might be due to the pore size and pore area enlargement of the membrane. The hydrophobic recovery for both the plasma-treated membranes is found significant for the initial ageing period of 7 days and found almost stable in nature after 7 days. A diffusion-based theoretical model is developed to study the hydrophobic recovery of plasma-treated membranes. A strong alignment between experimental and theoretical results is observed in the present work. The Cake Filtration model, derived from the Hermia model, is identified as the most suitable model for describing the fouling mechanisms for the present work.

Post-treatment of soft drink industrial wastewater using a new antibacterial ultra-filtration membrane prepared of Polyethersulfone blended with boehmite-tannic acid-graphene quantum dot.

Polymeric membranes have garnered great interest in wastewater treatment; however, fouling is known as their main limitation. Therefore, the blending of hydrophilic nanoparticles in polymeric membranes' structure is a promising approach for fouling reduction. Herein, a hydrophilic boehmite-tannic acid-graphene quantum dot (BM-TA-GQD) nanoparticle was synthesized and blended in a polyethersulfone polymeric membrane in different percentages. The fabricated membranes were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) images, water contact angle, porosity measurement, and antibacterial and antifouling properties. Surface SEM images of the modified membranes showed good dispersion of nanoparticles up to 0.5 wt%, which resulted in hydrophilicity and pure water flux enhancement. Based on AFM images, the mean roughness (Sa) of the fabricated membranes decreased from 2.07 to 0.84 nm for the bare and optimum membranes, respectively. In terms of performance, increasing the nanoparticle percentages up to 0.5 wt% resulted in the flux recovery ratio developing from 44.58% for the bare membrane to 71.35% for the 0.5 wt% BM-TA-GQD/PES membrane (optimum membrane). The antibacterial property of fabricated membranes was studied against biologically treated soft drink industrial wastewater (BTSDIW) as a bacterial source. The results showed that the turbidity of solutions containing permeated wastewater from the modified membranes (0.1, 0.5, and 1 wt% of BM-TA-GQD) was lower than that obtained from the unmodified membrane. These results confirmed the antibacterial properties of fabricated membranes. Finally, the optimal membrane (0.5 wt% BM-TA-GQD) was examined for post-treatment of the BTSDIW. An effluent COD of 13 mg/L and turbidity of 2 NTU showed a successful performance of the filtration process. PRACTITIONER POINTS: Ultrafiltration PES membranes were modified by different loadings of BM-TA-GQD. Hydrophilicity improvement was achieved by adding BM-TA-GQD nanoparticles. Expansion of size and number of macro-voids in modified membranes was confirmed. Membrane roughness was reduced in the BM-TA-GQD blended membranes. The optimum membrane was efficient in COD and turbidity removal.

Novel surface biochemical modifications of urinary catheters to prevent catheter-associated urinary tract infections.

More than 70% of hospital-acquired urinary tract infections are related to urinary catheters, which are commonly used for the treatment of about 20% of hospitalized patients. Urinary catheters are used to drain the bladder if there is an obstruction in the tube that carries urine out of the bladder (urethra). During catheter-associated urinary tract infections, microorganisms rise up in the urinary tract and reach the bladder, and cause infections. Various materials are used to fabricate urinary catheters such as silicone, polyurethane, and latex. These materials allow bacteria and fungi to develop colonies on their inner and outer surfaces, leading to bacteriuria or other infections. Urinary catheters could be modified to exert antibacterial and antifungal effects. Although so many research have been conducted over the past years on the fabrication of antibacterial and antifouling catheters, an ideal catheter needs to be developed for long-term catheterization of more than a month. In this review, we are going to introduce the recent advances in fabricating antibacterial materials to prevent catheter-associated urinary tract infections, such as nanoparticles, antibiotics, chemical compounds, antimicrobial peptides, bacteriophages, and plant extracts.

CoFe2O4 modified bentonite-based mixed matrix loose nanofiltration membranes for effective wastewater treatment.

Mixed-matrix membranes (MMMs) with an ideal polymer/hydrophilic flux enhancer interface considerably recuperates the separation and purification performance of membrane. In this direction, a novel CoFe2O4 functionalized natural clay-bentonite (CoFe2O4@BT) material as a compatible flux enhancer was synthesized for preparation of mixed matrix based in polyethersulfone (PES) matrix. Here, the influences of CoFe2O4@BT on the morphology and performance of the MMMs membranes were systematically investigated using various analytical techniques. Meanwhile, the water flux and sepration eficiency of the CoFe2O4@BT-PES membranes significantly enhanced due to the incorporation of CoFe2O4@BT that altered hydrophilicity, pore and surface characteristic features. The water flux as well as separation efficiency range up to 95%, 94.69%, 94.16% of Congo red (CR), Crystal violet (CV), and humic acid (HA) respectively. Meanwhile, the fouling parameters demonstrated that the CoFe2O4@BT-PES membranes exhibited better antifouling property in the long term experiment comparing with commercial polyamide membrane. CoFe2O4@BT material incorporated membranes showed less decline ratio and a better recovery ratio. The high rejection of dyes with a high permeation flux of the newly designed membranes indicated an amazing possibility for dye purification. In this study, a potential dye mechanism for composite membranes impacted by synthetic CoFe2O4@BT was also put forth. Within the context of application considerations for environmental protection, new materials stock in membranes show good potential for the separation of different organic contaminants.

Recent Advances in Dual-Function Superhydrophobic Antibacterial Surfaces.

Bacterial adhesion and subsequent biofilm formation on the surfaces of synthetic materials imposes a significant burden in various fields, which can lead to infections in patients or reduce the service life of industrial devices. Therefore, there is increasing interest in imbuing surfaces with antibacterial properties. Bioinspired superhydrophobic surfaces with high water contact angles (>150°) exhibit excellent surface repellency against contaminations, thereby preventing initial bacterial adhesion and inhibiting biofilm formation. However, conventional superhydrophobic surfaces typically lack long-term durability and are incapable of achieving persistent efficacy against bacterial adhesion. To overcome these limitations, in recent decades, dual-function superhydrophobic antibacterial surfaces with both bacteria-repelling and bacteria-killing properties have been developed by introducing bactericidal components. These surfaces have demonstrated improved long-term antibacterial performance in addressing the issues associated with surface-attached bacteria. This review summarizes the recent advancements of these dual-function superhydrophobic antibacterial surfaces. First, a brief overview of the fabrication strategies and bacteria-repelling mechanism of superhydrophobic surfaces is provided and then the dual-function superhydrophobic antibacterial surfaces are classified into three types based on the bacteria-killing mechanism: i) mechanotherapy, ii) chemotherapy, and iii) phototherapy. Finally, the limitations and challenges of current research are discussed and future perspectives in this promising area are proposed.

Anti-fouling potential and in-silico analysis of carotenoid and fatty acids from Rauvolfia tetraphylla L.

Study investigated the antifouling potential ofRauvolfia tetraphyllaL. fruit, leaf and stem extracts against the marine fouling organisms throughin-vitroand in-silicoapproach. Methanolic crude extract of R. tetraphylla L.leaf exhibited maximum antibacterial potential against six fouling organisms isolated from Parangipettai coast and was further taken up for column fractionation. Twenty-four fractions were obtained, among which five fractions showed inhibitory efficiency against microfoulers of Bacillus megaterium. The active compounds present in the bioactive fraction were identified by FTIR, GC-MS and NMR (13C; 1H). The bioactive compounds that exhibited maximum antifouling activity were identified as Lycopersene (80%), Hexadecanoic acid; 1, 2-Benzenedicarboxylic acid, dioctyl ester; Heptadecene - (8) - carbonic acid - (1) and Oleic acid. Molecular docking studies of the potent anti-fouling compounds Lycopersene, Hexadecanoic acid, 1, 2-Benzenedicarboxylic acid, dioctyl ester and Oleic acid showed the binding energy of 6.6, - 3.8, -5.3 and -5.9 (Kcal/mol) and hence these compounds will act as a potential biocide to control the aquatic foulers. Moreover, further studies need to carry out in terms of toxicity, field assessment and clinical trial in order to take these biocides for a patent.

Green Synthesis of TiO2 Nanoparticles Using Natural Marine Extracts for Antifouling Activity.

Titanium dioxide (TiO2) nanoparticles were synthesized via a novel eco-friendly green chemistry approach using marine natural extracts of two red algae (Bostrychia tenella and Laurencia obtusa), a green alga (Halimeda tuna), and a brown alga (Sargassum filipendula) along with a marine sponge sample identified as Carteriospongia foliascens. X-ray diffraction (XRD), scanning electron microscope (SEM), UV-Vis, X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared spectroscopy (FTIR) were employed to characterize the crystal structure, surface morphology, and optical properties of the synthesized nanoparticles. Each of the as-synthesized marine extract based TiO2 nanoparticles was individually incorporated as an antifouling agent to form a newly fabricated marine paint formulation. The newly prepared formulations were applied on unprimed steel panels. A comparative study with a commercial antifouling paint (Sipes Transocean Coatings Optima) was carried out. After 108 days of the coated steel panels' immersion in the Eastern Harbour seawater of Alexandria-Egypt, the prepared paints using B. tenella and C. foliascens extracts demonstrated an excellent antifouling performance toward fouling organisms by inhibiting their settlement and controlling their adhesion onto the immersed panels. In contrast, heavy fouling with barnacles was observed on the surface of the coated panel with the commercial paint. The physicochemical parameters of the seawater surrounding the immersed coated panels were estimated to investigate the influence of the fabricated paint formulations. Interestingly, no effects of the immersed coated panels on the physicochemical characteristics of the surrounding seawater were observed. Based on the obtained results and a comparison with commercially available antifouling products, the marine extract based TiO2 nanoparticle preparations of B. tenella and C. foliascens are promising candidates for eco-friendly antifouling agents. Based on the obtained results and a comparison with commercially available antifouling products, the marine extract based TiO2 nanoparticle preparations of B. tenella and C. foliascens are promising candidates for eco-friendly antifouling agents, which could be attributed to the small crystallite sizes of 22.86 and 8.3 nm, respectively, in addition to the incorporation of carbon in the crystal structure of the nanoparticles.

Self-cleaning and regenerable nano zero-valent iron modified PCN-224 heterojunction for photo-enhanced radioactive waste reduction.

The expansion of large-scale nuclear power causes a substantial volume of radioactive wastewater containing uranium to be released into the environment. Because of uranium's toxicity and bioaccumulation, it is critical to develop the efficient and sustainable materials for selective removal of uranium (VI). Herein, a regenerable anti-biofouling nano zero-valent iron doped porphyrinic zirconium metal-organic framework (NZVI@PCN-224) heterojunction system was successfully fabricated. Due to the Schottky-junction effect at the NZVI/MOF interface, the NZVI nanomaterial immobilized on PCN-224 could improve interfacial electron transfer and separation efficiency, and enhance entire reduction of highly soluble U(VI) to less soluble U(IV), involving photocatalytic reduction and chemical reduction. Meanwhile, the photocatalytic effect also prompts the NZVI@PCN-224 to produce more biotoxic reactive oxygen species (ROS), resulting in high anti-microbial and anti-algae activities. Under dark conditions, NZVI@PCN-224 with a large specific surface area could provide sufficient oxo atoms as the uranium binding sites and show the highest uranium-adsorbing capability of 57.94 mg/g at pH 4.0. After eight adsorption-desorption cycles, NZVI@PCN-224 still retained a high uranium adsorption capacity of 47.98 mg/g and elimination efficiency (91.72%). This sorption/reduction/anti-biofouling synergistic strategy of combining chelation, chemical reduction and photocatalytic performance inspires new insights for highly efficient treatment of liquid radioactive waste.

Crosslinked biomimetic coating modified stainless-steel-mesh enables completely self-cleaning separation of crude oil/water mixtures.

The development of high-flux, durable and completely self-cleaning membranes is highly desired for separation of massive oil/water mixtures. Herein, differently crosslinked poly(2-methacryloyloxylethyl phosphorylcholine) (PMPC) brush grafted stainless steel mesh (SSM) membranes (SSM/PMPCs) were fabricated by integrating of mussel inspired universal adhesion and crosslinking chemistry with surface-initiated activators regenerated by electron transfer atom transfer radical polymerization (SI-ARGET-ATRP). The durability and self-cleaning performance of the prepared SSM membranes were evaluated by separating sticky crude oil/water mixtures in a continuous recycling dead-end filtration device. The water filtration flux driven by gravity reached 60,000 L⋅m-2⋅h-1 with a separation efficiency of over 99.98%. Furthermore, zero-flux-decline was observed during a 5 h continuous filtration when assisted by mechanical stirring. More significantly, such a completely self-cleaning separation of the well crosslinked SSM/PMPC2 membrane under optimized flux and stirring conditions had been operated cumulatively for 190 h in 30 days without any additional cleaning. These significant advances are more promising for practical applications in crude oil-contaminated water treatments and massive oil/water mixture separation.

Anti-Pectin Fouling Performance of Dopamine and (3-Aminopropy) Triethoxysilane-Coated PVDF Ultrafiltration Membrane.

Due to the diversity and complexity of the components in traditional Chinese medicine (TCM) extracts, serious membrane fouling has become an obstacle that limits the application of membrane technology in TCM. Pectin, a heteropolysaccharide widely existing in plant cells, is the main membrane-fouling substance in TCM extracts. In this study, a hydrophilic hybrid coating was constructed on the surface of a polyvinylidene fluoride (PVDF) ultrafiltration (UF) membrane co-deposited with polydopamine (pDA) and (3-Aminopropy) triethoxysilane (KH550) for pectin antifouling. Characterization analysis showed that hydrophilic coating containing hydrophilic groups (-NH3, Si-OH, Si-O-Si) formed on the surface of the modified membrane. Membrane filtration experiments showed that, compared with a matched group (FRR: 28.66%, Rr: 26.87%), both the flux recovery rate (FRR) and reversible pollution rate (Rr) of the pDA and KH550 coated membrane (FRR: 48.07%, Rr: 44.46%) increased, indicating that pectin absorbed on the surface of membranes was more easily removed. Based on the extended Derjaguin-Laudau-Verwey-Overbeek (XDLVO) theory, the fouling mechanism of a PVDF UF membrane caused by pectin was analyzed. It was found that, compared with the pristine membrane (144.21 kT), there was a stronger repulsive energy barrier (3572.58 kT) to confront the mutual adsorption between the coated membrane and pectin molecule. The total interface between the modified membrane and the pectin molecule was significantly greater than the pristine membrane. Therefore, as the repulsion between them was enhanced, pectin molecules were not easily adsorbed on the surface of the coated membrane.

Biogenic synthesis of selenium and tellurium nanoparticles by marine bacteria and their biological activity.

Selenium (SeNPs) and tellurium nanoparticles (TeNPs) were synthesized by green technology using the three new bacterial marine isolates (strains PL 2476, AF 2469 and G 2451). Isolates were classified as Pseudoalteromonas shioyasakiensis according to 16S rRNA sequence analysis, morphological characteristics, and biochemical reactions. The bioreduction processes of isolates were studied in comparison with the previously described Alteromonas macleodii (strain 2328). All strains exhibited significant tolerance to selenite and tellurite up to 1000 µg/mL. A comparative analysis of the bioreduction processes of the isolates demonstrated that the strains have a high rate of reduction processes. Characterization of biogenic red SeNPs and black TeNPs using scanning electron microscopy (SEM), EDX analysis, Dynamic Light Scattering, and micro-Raman Spectroscopy revealed that all the isolates form stable spherical selenium and tellurium nanoparticles whose size as well as elemental composition depend on the producer strain. Nanoparticles of the smallest size (up to 100 nm) were observed only for strain PL 2476. Biogenic SeNPs and TeNPs were also characterized and tested for their antimicrobial, antifouling and cytotoxic activities. Significant antimicrobial activity was shown for nanoparticles at relatively high concentrations (500 and 1000 µg/mL), with the antimicrobial activity of TeNPs being more significant than SeNPs. In contrast, against cell cultures (breast cancer cells (SkBr3) and human dermal fibroblasts (HDF) SeNPs showed greater toxicity than tellurium nanoparticles. Studies have demonstrated the high antifouling effectiveness of selenium and tellurium nanoparticles when introduced into self-polishing coatings. According to the results obtained, the use of SeNPs and TeNPs as antifouling additives can reduce the concentration of leachable biocides used in coatings, reducing the pressure on the environment.

Slippery Antifouling Polymer Coatings Fabricated Entirely from Biodegradable and Biocompatible Components.

We report the design of slippery liquid-infused porous surfaces (SLIPS) fabricated from building blocks that are biodegradable, edible, or generally regarded to be biocompatible. Our approach involves infusion of lubricating oils, including food oils, into nanofiber-based mats fabricated by electrospinning or blow spinning of poly(ε-caprolactone), a hydrophobic biodegradable polymer used widely in medical implants and drug delivery devices. This approach leads to durable and biodegradable SLIPS that prevent fouling by liquids and other materials, including microbial pathogens, on objects of arbitrary shape, size, and topography. This degradable polymer approach also provides practical means to design "controlled-release" SLIPS that release molecular cargo at rates that can be manipulated by the properties of the infused oils (e.g., viscosity or chemical structure). Together, our results provide new designs and introduce useful properties and behaviors to antifouling SLIPS, address important issues related to biocompatibility and environmental persistence, and thus advance new potential applications, including the use of slippery materials for food packaging, industrial and marine coatings, and biomedical implants.

The Microbial Mechanisms of a Novel Photosensitive Material (Treated Rape Pollen) in Anti-Biofilm Process under Marine Environment.

Marine biofouling is a worldwide problem in coastal areas and affects the maritime industry primarily by attachment of fouling organisms to solid immersed surfaces. Biofilm formation by microbes is the main cause of biofouling. Currently, application of antibacterial materials is an important strategy for preventing bacterial colonization and biofilm formation. A natural three-dimensional carbon skeleton material, TRP (treated rape pollen), attracted our attention owing to its visible-light-driven photocatalytic disinfection property. Based on this, we hypothesized that TRP, which is eco-friendly, would show antifouling performance and could be used for marine antifouling. We then assessed its physiochemical characteristics, oxidant potential, and antifouling ability. The results showed that TRP had excellent photosensitivity and oxidant ability, as well as strong anti-bacterial colonization capability under light-driven conditions. Confocal laser scanning microscopy showed that TRP could disperse pre-established biofilms on stainless steel surfaces in natural seawater. The biodiversity and taxonomic composition of biofilms were significantly altered by TRP (p < 0.05). Moreover, metagenomics analysis showed that functional classes involved in the antioxidant system, environmental stress, glucose−lipid metabolism, and membrane-associated functions were changed after TRP exposure. Co-occurrence model analysis further revealed that TRP markedly increased the complexity of the biofilm microbial network under light irradiation. Taken together, these results demonstrate that TRP with light irradiation can inhibit bacterial colonization and prevent initial biofilm formation. Thus, TRP is a potential nature-based green material for marine antifouling.

Natural Benzo/Acetophenones as Leads for New Synthetic Acetophenone Hybrids Containing a 1,2,3-Triazole Ring as Potential Antifouling Agents.

Marine biofouling is a natural process that represents major economic, environmental, and health concerns. Some booster biocides have been used in biofouling control, however, they were found to accumulate in environmental compartments, showing negative effects on marine organisms. Therefore, it is urgent to develop new eco-friendly alternatives. Phenyl ketones, such as benzophenones and acetophenones, have been described as modulators of several biological activities, including antifouling activity (AF). In this work, acetophenones were combined with other chemical substrates through a 1,2,3-triazole ring, a strategy commonly used in Medicinal Chemistry. In our approach, a library of 14 new acetophenone-triazole hybrids was obtained through the copper(I)-catalyzed alkyne-azide cycloaddition "click" reaction. All of the synthesized compounds were evaluated against the settlement of a representative macrofouling species, Mytilus galloprovincialis, as well as on biofilm-forming marine microorganisms, including bacteria and fungi. The growth of the microalgae Navicula sp. was also evaluated after exposure to the most promising compounds. While compounds 6a, 7a, and 9a caused significant inhibition of the settlement of mussel larvae, compounds 3b, 4b, and 7b were able to inhibit Roseobacter litoralis bacterial biofilm growth. Interestingly, acetophenone 7a displayed activity against both mussel larvae and the microalgae Navicula sp., suggesting a complementary action of this compound against macro- and microfouling species. The most potent compounds (6a, 7a, and 9a) also showed to be less toxic to the non-target species Artemia salina than the biocide Econea®. Regarding both AF potency and ecotoxicity activity evaluation, acetophenones 7a and 9a were put forward in this work as promising eco-friendly AF agents.

Universal Antifouling and Photothermal Antibacterial Surfaces Based on Multifunctional Metal-Phenolic Networks for Prevention of Biofilm Formation.

Biofilms formed from the pathogenic bacteria that attach to the surfaces of biomedical devices and implantable materials result in various persistent and chronic bacterial infections, posing serious threats to human health. Compared to the elimination of matured biofilms, prevention of the formation of biofilms is expected to be a more effective way for the treatment of biofilm-associated infections. Herein, we develop a facile method for endowing diverse substrates with long-term antibiofilm property by deposition of a hybrid film composed of tannic acid/Cu ion (TA/Cu) complex and poly(ethylene glycol) (PEG). In this system, the TA/Cu complex acts as a multifunctional building block with three different roles: (i) as a versatile "glue" with universal adherent property for substrate modification, (ii) as a photothermal biocidal agent for bacterial elimination under irradiation of near-infrared (NIR) laser, and (iii) as a potent linker for immobilization of PEG with inherent antifouling property to inhibit adhesion and accumulation of bacteria. The resulted hybrid film shows negligible cytotoxicity and good histocompatibility and could prevent biofilm formation for at least 15 days in vitro and suppress bacterial infection in vivo, showing great potential for practical applications to solve the biofilm-associated problems of biomedical materials and devices.

Data on elemental concentrations in marine sediments from the South and South West of England.

The present Data In Brief methodological paper details the acquisition, mining and pre-processing of elemental concentration data in marine sediments (coastal and open sea) of Southern England, presented and discussed in the co-submitted Environment International paper entitled: "Three decades of trace element sediment contamination: the mining of governmental databases and the need to address hidden sources for clean and healthy seas" [1]. Elemental sediment concentration data were obtained from the two main UK environmental sources, i.e. the Environment Agency (EA) and the Marine Environment Monitoring and Assessment National (MERMAN) database managed by the British Oceanographic Data Centre (BODC). The merged database is the result of a rigorous data selection-validation process and provides spatially and temporally extensive records of arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), iron (Fe), mercury (Hg), nickel (Ni), lead (Pb) and zinc (Zn) concentrations for hundreds of sites over 31 years (1983-2013). Additional records of manganese (Mn), aluminium (Al), lithium (Li), tin (Sn) [and tributyltin (TBT)], barium (Ba), antimony (Sb), boron (B), calcium (Ca), molybdenum (Mo), cobalt (Co), selenium (Se), potassium (K), magnesium (Mg), beryllium (Be), vanadium (V), titanium (Ti), sodium (Na), silver (Ag), thallium (Tl) and strontium (Sr) are also included. The full secondary database is hosted in the Mendeley Data repository and the geo-spatial information to map sites is given in supplementary files to the paper. To provide end-users with the relevant context on spatial and temporal coverage, monitoring statistics are given for the nine trace elements (TEs). Site-specific statistics include: the first and last year of sediment monitoring, the number of years monitored, and minimum, maximum, mean and median numbers of years monitored. Also given are summary data on the number of sites monitored each year, from the first records from 1983 to 2013. For the nine TEs (total and strong acid digestion techniques are considered separately for Cr and Fe), monitoring statistics are presented separately for coastal and open sea sites. Data are relevant to diverse end-users to assess the local and regional contaminant loads and to contextualize anthropogenic threats to benthic systems in multiple locations from the French/English Channel, southern North and Celtic Seas.

Fabrication of zinc doped aluminium oxide/polysulfone mixed matrix membranes for enhanced antifouling property and heavy metal removal.

Heavy metal removal from water resources is essential for environmental protection and the production of safe drinking water. In this direction, Zinc doped Aluminium Oxide (Zn:Al2O3) nanoparticles were incorporated into Polysulfone (PSf) to prepare mixed matrix membranes for the efficient removal of heavy metals from water. These Zn:Al2O3 nanoparticles prepared by the solution combustion method have a very high surface area (261.44 m2/g) with an approximate size of 50 nm. X-ray Photoelectron Spectroscopy analysis showed that the Al and Zn were in +3 and + 2 oxidation states, respectively. Cross-sectional Scanning Electron Microscopy images revealed the finger-like morphology and porous nature of the membranes. In this study, the optimum loading amount of Zn:Al2O3 nanoparticles was determined. Synthesized membranes showed enhanced hydrophilicity, surface charge, and porosity, which enabled the removal of arsenic and lead with efficiencies of 87% and 98%, respectively. A study of the antifouling properties carried out at various pressures with a feed solution containing Bovine Serum Albumin (BSA) showed 98.4% of flux recovery ratio and reusability up to three continuous cycles. Moreover, this work demonstrates a rational design of novel mixed matrix membranes exhibiting characteristics of hydrophilicity, surface charge, and porosity adequate to realize the efficient removal of heavy metals.

Ammonium ultra-selective membranes for wastewater treatment and nutrient enrichment: Interplay of surface charge and hydrophilicity on fouling propensity and ammonium rejection.

Membrane fouling and ammonium transmembrane diffusion simultaneously pose great challenges in membrane-based pre-concentration of domestic wastewater for efficient subsequent resources recovery (i.e., energy and nutrients). Herein, amine-functionalized osmotic membranes were fabricated by optimizing the grafting pathway of polyamidoamine (PAMAM) dendrimer to mitigate fouling and ammonium transmembrane diffusion. Compared to the control membrane, the PAMAM-grafted membranes with abundant primary amine groups possessed substantially increased hydrophilicity and positive charges (i.e., protonated primary amines) and thus exhibited superior anti-fouling capability and ammonium selectivity. With further increasing the PAMAM grafting ratio, the membrane exhibited a steady enhancement in ammonium selectivity and eventually achieved an ultra-high ammonium rejection of 99.4%. Nevertheless, the anti-fouling capability of such ammonium ultra-selective membrane was weakened due to the suppression of the adverse impact of excessive positive charges over the beneficial effect of increased surface hydrophilicity. This in turn leads to a drop of ammonium rejection below 90% during domestic wastewater concentration. This study demonstrates that the membrane with a moderate primary amine loading could achieve the highest anti-fouling capability with only less than 10% flux decline and meanwhile maintain an excellent ammonium rejection above 94% during raw domestic wastewater concentration. This work provides theoretical guidance for fabricating simultaneously enhanced anti-fouling and ammonia-rejecting membranes.

Well-Defined Gold Nanorod/Polymer Hybrid Coating with Inherent Antifouling and Photothermal Bactericidal Properties for Treating an Infected Hernia.

Biomedical device-associated infection (BAI) is a great challenge in modern clinical medicine. Therefore, developing efficient antibacterial materials is significantly important and meaningful for the improvement of medical treatment and people's health. In the present work, we developed a strategy of surface functionalization for multifunctional antibacterial applications. A functionalized polyurethane (PU, a widely used biomedical material for hernia repairing) surface (PU-Au-PEG) with inherent antifouling and photothermal bactericidal properties was readily prepared based on a near-infrared (NIR)-responsive organic/inorganic hybrid coating which consists of gold nanorods (Au NRs) and polyethylene glycol (PEG). The PU-Au-PEG showed a high efficiency to resist adhesion of bacteria and exhibited effective photothermal bactericidal properties under 808 nm NIR irradiation, especially against multidrug-resistant bacteria. Furthermore, the PU-Au-PEG could inhibit biofilm formation long term. The biocompatibility of PU-Au-PEG was also proved by cytotoxicity and hemolysis tests. The in vivo photothermal antibacterial properties were first verified by a subcutaneous implantation animal model. Then, the anti-infection performance in a clinical scenario was studied with an infected hernia model. The results of animal experiment studies demonstrated excellent in vivo anti-infection performances of PU-Au-PEG. The present work provides a facile and promising approach to develop multifunctional biomedical devices.

The Marine Seagrass Halophila stipulacea as a Source of Bioactive Metabolites against Obesity and Biofouling.

Marine organisms, including seagrasses, are important sources of biologically active molecules for the treatment of human diseases. In this study, organic extracts of the marine seagrass Halophila stipulacea obtained by different polarities from leaves (L) and stems (S) (hexane [HL, HS], ethyl acetate [EL, ES], and methanol [ML, MS]) were tested for different bioactivities. The screening comprehended the cytotoxicity activity against cancer cell lines grown as a monolayer culture or as multicellular spheroids (cancer), glucose uptake in cells (diabetes), reduction of lipid content in fatty acid-overloaded liver cells (steatosis), and lipid-reducing activity in zebrafish larvae (obesity), as well as the antifouling activity against marine bacteria (microfouling) and mussel larval settlement (macrofouling). HL, EL, HS, and ES extracts showed statistically significant cytotoxicity against cancer cell lines. The extracts did not have any significant effect on glucose uptake and on the reduction of lipids in liver cells. The EL and ML extracts reduced neutral lipid contents on the larvae of zebrafish with EC50 values of 2.2 µg/mL for EL and 1.2 µg/mL for ML. For the antifouling activity, the HS and ML extracts showed a significant inhibitory effect (p < 0.05) against the settlement of Mytilus galloprovincialis plantigrade larvae. The metabolite profiling using HR-LC-MS/MS and GNPS (The Global Natural Product Social Molecular Networking) analyses identified a variety of known primary and secondary metabolites in the extracts, along with some unreported molecules. Various compounds were detected with known activities on cancer (polyphenols: Luteolin, apeginin, matairesinol), on metabolic diseases (polyphenols: cirsimarin, spiraeoside, 2,4-dihydroxyheptadec-16-ynyl acetate; amino acids: N-acetyl-L-tyrosine), or on antifouling (fatty acids: 13-decosenamide; cinnamic acids: 3-hydroxy-4-methoxycinnamic acid, alpha-cyano-4-hydroxycinnamic), which could be, in part, responsible for the observed bioactivities. In summary, this study revealed that Halophila stipulacea is a rich source of metabolites with promising activities against obesity and biofouling and suggests that this seagrass could be useful for drug discovery in the future.