Multi-project wafers for flexible thin-film electronics by independent foundries.

Flexible and large-area electronics rely on thin-film transistors (TFTs) to make displays1-3, large-area image sensors4-6, microprocessors7-11, wearable healthcare patches12-15, digital microfluidics16,17 and more. Although silicon-based complementary metal-oxide-semiconductor (CMOS) chips are manufactured using several dies on a single wafer and the multi-project wafer concept enables the aggregation of various CMOS chip designs within the same die, TFT fabrication is currently lacking a fully verified, universal design approach. This increases the cost and complexity of manufacturing TFT-based flexible electronics, slowing down their integration into more mature applications and limiting the design complexity achievable by foundries. Here we show a stable and high-yield TFT platform for the fabless manufacturing of two mainstream TFT technologies, wafer-based amorphous indium-gallium-zinc oxide and panel-based low-temperature polycrystalline silicon, two key TFT technologies applicable to flexible substrates. We have designed the iconic 6502 microprocessor in both technologies as a use case to demonstrate and expand the multi-project wafer approach. Enabling the foundry model for TFTs, as an analogy of silicon CMOS technologies, can accelerate the growth and development of applications and technologies based on these devices.

Aqueous Solution-Grown Crystalline Phosphorus Doped Indium Oxide for Thin-Film Transistors Applications.

Solution-grown indium oxide (In2O3) based thin-film transistors (TFTs) hold good prospects for emerging advanced electronics due to their excellent mobility, prominent transparency, and possibility of low-cost and scalable manufacturing; however, pristine In2O3 TFTs suffer from poor switching characteristics due to intrinsic oxygen-vacancy-related defects and require external doping. According to Shanmugam's theory, among potential dopants, phosphorus (P) has a large dopant-oxygen bonding strength (EM-O) and high Lewis acid strength (L) that would suppress oxygen-vacancy related defects and mitigate dopant-induced carrier scattering; however, P-doped In2O3 (IPO) TFTs have not yet been demonstrated. Here, we report aqueous solution-grown crystalline IPO TFTs for the first time. It is suggested that the incorporation of P could effectively inhibit oxygen-vacancy-related defects while maintaining high mobility. This work experimentally demonstrates that dopant with high EM-O and L is promising for emerging oxide TFTs.

Large-scale aqueous synthesis of Cu(In,Ga)Se2 nanoparticles for photocatalytic degradation of ciprofloxacin.

Environmentally friendly synthesis of Cu(In,Ga)Se2 (CIGS) nanoparticles (NPs) is pivotal for producing sustainable photocatalytic compounds to be applied in the remediation of contaminants of emerging concern from water. To this end, we herein report an aqueous synthesis of CIGS NPs, followed by annealing, to give access to phase-pure CIGS crystals with chalcopyrite structure and no signs of secondary phases. Morphological and compositional characterization revealed NPs with an average size of 10-35 nm and uniform distribution of Cu, In, Ga, and Se elements. In addition, the first aqueous large-scale synthesis of CIGS NPs is developed by up-scaling the synthesis procedure, resulting in 5 g of highly crystalline nanoparticles exhibiting an ideal optical band gap of 1.14 eV. The as-synthesized NPs proved the ability to remove 71 and 83% of a contaminant of emerging concern, ciprofloxacin (CIP), under ultraviolet (UV) and visible (Vis) radiations, respectively.

Diagnosis of Prostate Cancer and Prostatitis Using near Infra-Red Fluorescent AgInSe/ZnS Quantum Dots.

The link between the microbiome and cancer has led researchers to search for a potential probe for intracellular targeting of bacteria and cancer. Herein, we developed near infrared-emitting ternary AgInSe/ZnS quantum dots (QDs) for dual bacterial and cancer imaging. Briefly, water-soluble AgInSe/ZnS QDs were synthesized in a commercial kitchen pressure cooker. The as-synthesized QDs exhibited a spherical shape with a particle diameter of 4.5 ± 0.5 nm, and they were brightly fluorescent with a photoluminescence maximum at 705 nm. The QDs showed low toxicity against mouse mammary carcinoma (FM3A-Luc), mouse colon carcinoma (C26), malignant fibrous histiocytoma-like (KM-Luc/GFP) and prostate cancer cells, a greater number of accumulations in Staphylococcus aureus, and good cellular uptake in prostate cancer cells. This work is an excellent step towards using ternary QDs for diagnostic and guided therapy for prostate cancer.

Assessment of Occupational Exposure to Indium Dust for Indium-Tin-Oxide Manufacturing Workers.

According to recent research, indium nanoparticles (NPs) are more toxic than micro-sized particles. While cases of indium lung disease have been reported worldwide, very little research has been conducted on the occupational exposure to indium NPs. Recently, an indium-related lung disease was reported in Korea, a global powerhouse for display manufacturing. In this study, we conducted an assessment ofoccupational exposure at an indium tin oxide (ITO) powder manufacturing plant, where the first case of indium lung disease in Korea occurred. Airborne dustwas obtained from a worker's breathing zone, and area sampling in the workplace environment was conducted using real-time monitoring devices. Personal samples were analyzed for the indium concentrations in total dust, respirable dust fraction, and NPs using personal NPs respiratory deposition samplers. The total indium concentration of the personal samples was lower than the threshold limit value recommended by the American Conference of Governmental Industrial Hygienists (ACGIH TLV), which was set as occupational exposure limit (OEL). However, the respirable indium concentration exceeded the recently set ACGIH TLV for the respirable fraction of indium dust. The concentration of indium NPs ranged between 0.003 and 0.010 × 10-2 mg/m3, accounting for only 0.4% of the total and 2.7% of the respirable indium particles. This was attributed to the aggregating of NPs at the µm sub-level. Given the extremely low fraction of indium NPs in the total and respirable dust, the current OEL values, set as the total and respirable indium concentrations, do not holistically represent the occupational exposure to indium NPs or prevent health hazards. Therefore, it is necessary to set separate OEL values for indium NPs. This study covers only the process of handling ITO powder. Therefore, follow-up studies need to be conducted on other ITO sputtering target polishing and milling processes, which typically generate more airborne NPs, to further investigate the effects of indium on workers and facilitate the necessary implementation of indium-reducing technologies.

Enhancing photoelectrochemical performance of ZnIn2S4 by phosphorus doping for sensitive detection of miRNA-155.

We report the synthesis of phosphorus-doped ZnIn2S4 (ZnIn2S4-xPx) materials through a solid/gas-phase reaction. ZnIn2S4-xPx shows enhanced photoelectrochemical (PEC) performance due to the improved photo-carrier separation efficiency achieved by substituting some of the sulfur with phosphorus. A PEC biosensor was further developed based on ZnIn2S4-xPx, which exhibits excellent analytical performance for miRNA-155.

Water-soluble ZnCuInSe quantum dots for bacterial classification, detection, and imaging.

Bacteria are everywhere and pose severe threats to human health and safety. The rapid classification and sensitive detection of bacteria are vital steps of bacterial community research and the treatment of infection. Herein, we developed optical property-superior and heavy metal-free ZnCuInSe quantum dots (QDs) for achieving rapid discrimination of Gram-positive/Gram-negative bacteria by the naked eye; driven by the structural differences of bacteria, ZnCuInSe QDs are effective in binding to Gram-positive bacteria, especially Staphylococcus aureus (S. aureus), in comparison with Gram-negative bacteria and give discernable color viewed by the naked eye. Meanwhile, based on its distinctive fluorescence response, the accurate quantification of S. aureus was investigated with a photoluminescence system in the concentration ranges of 1 × 103 to 1 × 1011 CFU/mL, with a limit of detection of 1 × 103 CFU/mL. Furthermore, we demonstrated the feasibility of ZnCuInSe QDs as a fluorescence probe for imaging S. aureus. This simple strategy based on ZnCuInSe QDs provides an unprecedented step for rapid and effective bacterial discrimination, detection, and imaging.

Aqueous Synthesis of DNA-Functionalized Near-Infrared AgInS2/ZnS Core/Shell Quantum Dots.

Biocompatibility, biofunctionality, and chemical stability are essential criteria to be fulfilled by quantum dot (QD) emitters for bio-imaging and -sensing applications. In addition to these criteria, achieving efficient near-infrared (NIR) emission with nontoxic QDs remains very challenging. In this perspective, we developed water-soluble NIR-emitting AgInS2/ZnS core/shell (AIS/ZnS) QDs functionalized with DNA. The newly established aqueous route relying on a two-step hot-injection synthesis led to highly luminescent chalcopyrite-type AIS/ZnS core/shell QDs with an unprecedented photoluminescence quantum yield (PLQY) of 55% at 700 nm and a long photoluminescence (PL) decay time of 900 ns. Fast and slow hot injection of the precursors were compared for the AIS core QD synthesis, yielding a completely different behavior in terms of size, size distribution, stoichiometry, and crystal structure. The PL peak positions of both types of core QDs were 710 (fast) and 760 nm (slow injection) with PLQYs of 36 and 8%, respectively. The slow and successive incorporation of the Zn and S precursors during the subsequent shell growth step on the stronger emitting cores promoted the formation of a three-monolayer thick ZnS shell, evidenced by the increase of the average QD size from 3.0 to 4.8 nm. Bioconjugation of the AIS/ZnS QDs with hexylthiol-modified DNA was achieved during the ZnS shell growth, resulting in a grafting level of 5-6 DNA single strands per QD. The successful chemical conjugation of DNA was attested by UV-vis spectroscopy and agarose gel electrophoresis. Importantly, surface plasmon resonance imaging experiments using complementary DNA strands further corroborated the successful coupling and the stability of the AIS/ZnS-DNA QD conjugates as well as the preservation of the biological activity of the anchored DNA. The strong NIR emission and biocompatibility of these AIS/ZnS-DNA QDs provide a high potential for their use in biomedical applications.

AgInSe2-Sensitized ZnO Nanoflower Wide-Spectrum Response Photoelectrochemical/Visual Sensing Platform via Au@Nanorod-Anchored CeO2 Octahedron Regulated Signal.

Herein an ultrasensitive photoelectrochemical (PEC)/visual biosensor coupled with a multiple signal amplification strategy was proposed for the detection of nucleic acids. The initial signal amplification was achieved via ternary AgInSe2 quantum dot (QD)-sensitized ZnO nanoflowers (ZnO NFs) to form an excellent photoelectric layer. A gold-modified nanorod-anchored CeO2 (Au@NR-CeO2) octahedron was introduced as a multifunctional signal regulator via the formation of triple helix molecules. The Au@NR-CeO2 octahedron could not only quench the photocurrent signal due to the competitive capture of photon energy and electron donors with the photoelectric layer but could also act like a peroxidase to catalyze the formation of mimetic enzymatic catalytic precipitation (MECP) on the surface of the photoelectric layer. Furthermore, the steric hindrance effect from the Au@NR-CeO2 octahedron further reduced the output of the photocurrent signal. After incubation with t-DNA, the triple helix conformation was disassembled and the Au@NR-CeO2 octahedron was released from the electrode surface, leading to the significant increase of photocurrent signal. Meanwhile, the released Au@NR-CeO2 octahedron could flow into the colorimetric area of the lab-on-paper device to catalyze the occurrence of the color reaction, achieving a visual detection for t-DNA. On the basis of the multiple signal amplification strategy, t-DNA was detected specifically with a lower limit of detection of 0.28 fM and a wider linear range from 0.5 fM to 50 nM. The proposed method has the potential utility to detect a variety of nucleic acids and biomarkers.

Efficient photocatalytic inactivation of E. coli by Mn-CdS/ZnCuInSe/CuInS2 quantum dots-sensitized TiO2 nanowires.

A novel visible light-driven photocatalyst (represented as Mn-CdS/ZCISe/CIS/TiO2) for the passivation of E. coli was prepared with TiO2 nanowires as support and using CuInS2 (CIS) and ZnCuInSe (ZCISe) quantum dots (QDs), as well as Mn-doped CdS (Mn-CdS) nanoparticles (NPs) as sensitizers. The use of CIS and ZCISe QDs and Mn-CdS NPs extends the light harvest region to visible light. The photoelectric conversion efficiency was consequently improved, with a photocurrent density of 12.5 mA cm-2, about 60 times that of pure TiO2 nanowires. The germicidal efficiency of the photocatalyst was assessed by passivation of E. coli, 96% bacteria in 50 ml 105 colony forming units (CFU) ml-1 solution were killed within 50 min. Besides the high efficiency, the composite has good stability and satisfactory recycling performance. The antibiotic mechanism was also performed by using photoluminescence and a scavenging agent of different active matter, revealing that the photo-generated holes play a major role in the sterilization process.

In vivo Comparison of the Biodistribution and Toxicity of InP/ZnS Quantum Dots with Different Surface Modifications.

INTRODUCTION: Indium phosphide (InP) quantum dots (QDs) have shown a broad application prospect in the fields of biophotonics and nanomedicine. However, the potential toxicity of InP QDs has not been systematically evaluated. In particular, the effects of different surface modifications on the biodistribution and toxicity of InP QDs are still unknown, which hinders their further developments. The present study aims to investigate the biodistribution and in vivo toxicity of InP/ZnS QDs. METHODS: Three kinds of InP/ZnS QDs with different surface modifications, hQDs (QDs-OH), aQDs (QDs-NH2), and cQDs (QDs-COOH) were intravenously injected into BALB/c mice at the dosage of 2.5 mg/kg BW or 25 mg/kg BW, respectively. Biodistribution of three QDs was determined through cryosection fluorescence microscopy and ICP-MS analysis. The subsequent effects of InP/ZnS QDs on histopathology, hematology and blood biochemistry were evaluated at 1, 3, 7, 14 and 28 days post-injection. RESULTS: These types of InP/ZnS QDs were rapidly distributed in the major organs of mice, mainly in the liver and spleen, and lasted for 28 days. No abnormal behavior, weight change or organ index were observed during the whole observation period, except that 2 mice died on Day 1 after 25 mg/kg BW hQDs treatment. The results of H&E staining showed that no obvious histopathological abnormalities were observed in the main organs (including heart, liver, spleen, lung, kidney, and brain) of all mice injected with different surface-functionalized QDs. Low concentration exposure of three QDs hardly caused obvious toxicity, while high concentration exposure of the three QDs could cause some changes in hematological parameters or biochemical parameters related to liver function or cardiac function. More attention needs to be paid on cQDs as high-dose exposure of cQDs induced death, acute inflammatory reaction and slight changes in liver function in mice. CONCLUSION: The surface modification and exposure dose can influence the biological behavior and in vivo toxicity of QDs. The surface chemistry should be fully considered in the design of InP-based QDs for their biomedical applications.

GaAs-Based InPBi Quantum Dots for High Efficiency Super-Luminescence Diodes.

InPBi exhibits broad and strong photoluminescence at room temperature, and is a potential candidate for fabricating super-luminescence diodes applied in optical coherence tomography. In this paper, the strained InPBi quantum dot (QD) embedded in the AlGaAs barrier on a GaAs platform is proposed to enhance the light emission efficiency and further broaden the photoluminescence spectrum. The finite element method is used to calculate the strain distribution, band alignment and confined levels of InPBi QDs. The carrier recombinations between the ground states and the deep levels are systematically investigated. A high Bi content and a flat QD shape are found preferable for fabricating super-luminescence diodes with high efficiency and a broad emission spectrum.

Piezoresistivity of InAsP Nanowires: Role of Crystal Phases and Phosphorus Atoms in Strain-Induced Channel Conductances.

Strong piezoresistivity of InAsP nanowires is rationalized with atomistic simulations coupled to Density Functional Theory. With a focal interest in the case of the As(75%)-P(25%) alloy, the role of crystal phases and phosphorus atoms in strain-driven carrier conductance is discussed with a direct comparison to nanowires of a single crystal phase and a binary (InAs) alloy. Our analysis of electronic structures presents solid evidences that the strong electron conductance and its sensitivity to external tensile stress are due to the phosphorous atoms in a Wurtzite phase, and the effect of a Zincblende phase is not remarkable. With several solid connections to recent experimental studies, this work can serve as a sound framework for understanding of the unique piezoresistive characteristics of InAsP nanowires.

A tyrosinase-induced fluorescence immunoassay for detection of tau protein using dopamine-functionalized CuInS2/ZnS quantum dots.

Rapid, highly sensitive detection of tau protein and other neurodegenerative biomarkers remains a significant hurdle for diagnostic tests for Alzheimer's disease. In this work, we developed a novel tyrosinase (TYR)-induced tau aptamer-tau-tau antibody (anti-tau) sandwich fluorescence immunoassay to detect tau protein that used dopamine (DA)-functionalized CuInS2/ZnS quantum dots as the fluorophore. CuInS2/ZnS core/shell quantum dots with high luminescence, low toxicity, and excellent biocompatibility were successfully fabricated and decorated with DA through amide conjugation. Meanwhile, TYR was conjugated with anti-tau by a click reaction. When DA-functionalized CuInS2/ZnS quantum dots were added to the sandwich system, TYR catalyzed the transformation of DA to dopamine quinone, which acted as an effective electron acceptor and triggered fluorescence quenching. The fluorescence intensity of the immunoassay based on DA-functionalized CuInS2/ZnS quantum dots shows good performance in terms of linearity with the logarithm of tau protein concentration, with a linear concentration range from 10 pM to 200 nM. This work is the first to use a TYR-induced fluorescence immunoassay for the rapid detection of tau protein, paving a new way for the detection of disease biomarkers. Graphical abstract.

Opto-electronic and thermoelectric properties of MgIn2X4 (X = S, Se) spinels via ab-initio calculations.

The structural behavior of MgIn2X4 (X = S, Se) has been elaborated by FP-LAPW + lo method as included in the Wien2k code. The stability of the phase has been confirmed by negative formation energy (-1.24 eV for MgIn2S4 and -0.78 eV for MgIn2Se4). The band gap dependent opto-electronic and thermoelectric properties are realized by modified Becke-Johnson exchange potential. The electronic band gap tuned from ultraviolet to visible (3.1 eV and 1.9 eV) by replacing the S with Se that motivated the studied spinels for photovoltaic and solar applications. Moreover, the attenuation of light, dispersion, transparency, reflection and energy loss when light scattered from material are discussed as function of energy. The thermal conductivity to electrical conductivity ratio, potential gradient and thermal efficiency in the range 0.78-0.80 are elaborated. The comparative study of opto-electronic and thermoelectric properties for energy harvesting increases the potential for optoelectronic than thermoelectric applications.

Towards improving the electroanalytical speciation analysis of indium.

The geochemical fate of indium in natural waters is still poorly understood, while recent studies have pointed out a growing input of this trivalent element in the environment as a result of its utilisation in the manufacturing of high-technology products. Reliable and easy-handling analytical tools for indium speciation analysis are, then, required. In this work, we report the possibility of measuring the total and free indium concentrations in solution using two complementary electroanalytical techniques, SCP (Stripping chronopotentiometry) and AGNES (Absence of Gradients and Nernstian Equilibrium Stripping) implemented with the TMF/RDE (Thin Mercury Film/Rotating Disk Electrode). Nanomolar limits of detection, i.e. 0.5 nM for SCP and 0.1 nM for AGNES, were obtained for both techniques in the experimental conditions used in this work and can be further improved enduring longer experiment times. We also verified that AGNES was able (i) to provide robust speciation data with the known In-oxalate systems and (ii) to elaborate indium binding isotherms in presence of humic acids extending over 4 decades of free indium concentrations. The development of electroanalytical techniques for indium speciation opens up new routes for using indium as a potential tracer for biogeochemical processes of trivalent elements in aquifers, e.g. metal binding to colloidal phases, adsorption onto (bio)surfaces, etc.

Cascaded systems analysis of a-Se/a-Si and a-InGaZnO TFT passive and active pixel sensors for tomosynthesis.

Medical imaging systems like full field digital mammography (FFDM) and digital breast tomosynthesis (DBT) commonly use amorphous selenium (a-Se) based passive pixel sensor (PPS) direct conversion x-ray detectors. On one hand, direct conversion detectors inherently offer better resolution characteristics in terms of a higher modulation transfer function (MTF), in comparison to the indirect CsI:Tl PPS x-ray imager. On the other hand, especially at lower doses, this superior performance of the direct imager is seldom retained in its detective quantum efficiency (DQE) curves. It is well known that a-Se PPS x-ray imagers suffer from high additive electronic noise originating from the from the amorphous silicon (a-Si) thin film transistor (TFT) array that is being used in the current back-plane technology. This degrades the noise power spectrum (NPS) and subsequently the overall DQE. To address this deficiency, we propose to replace the PPS back-plane by active pixel sensor (APS) back-plane technology, which has the potential to reduce the back-plane electronic noise by amplifying the input signal, especially at low doses. The proposed APS is based on amorphous In-Ga-Zn-O (a-IGZO) TFT technology, which can offer high mobility (5-20 cm2 V-1 s-1), low leakage current (<10-13 A) and low flicker noise (Hooge's parameter α H ~ 1.5 [Formula: see text] 10-3), leading to better imager noise performance. To test our hypothesis, we used linear cascaded systems analysis to model the imaging performance (MTF, NPS and DQE) of the PPS and APS a-Se direct imagers. This model was first validated using experimentally measured data obtained for a 85 µm pixel pitch a-Se/a-Si TFT PPS imager. Using this model, we analyzed the noise performance of the direct a-Se and indirect CsI:Tl x-ray a-IGZO APS imagers at different dose and electronic noise levels. Obtained results clearly showed that lowering back-plane electronic noise can significantly improve the performance of the a-Se/a-IGZO TFT APS imager. Our simulated results showed that a higher DQE at lower radiation doses (maximum DQE of 0.6 can be achieved at an exposure level of 1 µGy) can be achieved with the a-Se detector, thereby making this combination a promising candidate for low dose applications like DBT.

Mixed and Matched Metallo-Nanotexaphyrin for Customizable Biomedical Imaging.

The discovery and synthesis of multifunctional organic building blocks for nanoparticles have remained challenging. Texaphyrin macrocycles are multifunctional, all-organic compounds that possess versatile metal-chelation capabilities and unique theranostics properties for biomedical applications. Unfortunately, there are significant difficulties associated with the synthesis of texaphyrin-based subunits capable of forming nanoparticles. Herein, the detailed synthesis of a texaphyrin-phospholipid building block is reported via a key 1,2-dinitrophenyl-phospholipid intermediate, along with stable chelation of two clinically relevant metal ions into texaphyrin-lipid without compromising their self-assembly into texaphyrin nanoparticles or nanotexaphyrin. A postinsertion methodology to quantitatively insert a variety of metal-ions into preformed nanotexaphyrins is developed and employed to synthesize a structurally stable, mixed 111 indium-manganese-nanotexaphyrin for dual modal single-photon emission computed tomography (SPECT) and magnetic resonance imaging (MRI). In vivo dual SPECT/MRI imaging of 111 In-Mn-nanotexaphyrins in an orthotopic prostatic PC3 mouse model demonstrates complementary signal enhancement in the tumor with both modalities at 22 h post intravenous administration. This result highlights the utility of hybrid metallo-nanotexaphyrins to achieve sensitive and accurate detection of tumors by accommodating multiple imaging modalities. The power of this mixed and matched metallo-nanotexaphyrin strategy can be unleashed to allow a diverse range of multifunctional biomedical imaging.

In Situ Monitoring of the Accelerated Performance Degradation of Solar Cells and Modules: A Case Study for Cu(In,Ga)Se2 Solar Cells.

The levelized cost of electricity (LCOE) of photovoltaic (PV) systems is determined by, among other factors, the PV module reliability. Better prediction of degradation mechanisms and prevention of module field failure can consequently decrease investment risks as well as increase the electricity yield. An improved knowledge level can for these reasons significantly decrease the total costs of PV electricity. In order to better understand and minimize the degradation of PV modules, the occurring degradation mechanisms and conditions should be identified. This should preferably happen under combined stresses, since modules in the field are also simultaneously exposed to multiple stress factors. Therefore, two 'Combined Stress test with in situ measurement' setups have been designed and constructed. These setups allow the simultaneous use of humidity, temperature, illumination, and electrical biases as independently controlled stress factors on solar cells and minimodules. The setups also allow real-time monitoring of the electrical properties of these samples. This protocol presents these setups and describes the experimental possibilities. Moreover, results obtained with these setups are also presented: various examples about the influence of both deposition and degradation conditions on the stability of thin film Cu(In,Ga)Se2 (CIGS) as well as Cu2ZnSnSe4 (CZTS) solar cells are described. Results on the temperature dependency of CIGS solar cells are also presented.

Solution-Processable Two-Dimensional In2 Se3 Nanosheets as Efficient Photothermal Agents for Elimination of Bacteria.

Two-dimensional (2D) nanoflakes represent an appealing class of materials for optoelectronics applications due to their unique layered structures and excellent electronic properties. However, the lack of easy-to-manipulate and effective methods for large-scale production of these 2D materials limits their potential for applications. Also, few efforts have been made to explore their applications in biological fields. This work reports the preparation of large quantities of 2D In2 Se3 nanosheets through a solvent exfoliation technique. Transmission electron microscopy and atomic force microscopy results show that the In2 Se3 nanosheets are obtained with lateral sizes of tens of nanometers to hundreds of nanometers and thickness of 2-17 layers. Raman features coupled with the X-ray diffractometry results unequivocally confirm the as-prepared In2 Se3 nanosheets to be α phase. Moreover, these α-In2 Se3 nanosheets exhibit an excellent near-infrared (NIR) photothermal performance under an 808 nm laser irradiation. NIR photo-excitation of the α-In2 Se3 nanosheets in the presence of bacteria leads to a significant antibacterial effect, suggesting that these nanosheets have great potential to be photothermal antibacterial agents. Our work on α-In2 Se3 nanosheets presents an available method for exfoliating 2D layered materials, and highlights the potential application in chemical and biological fields of α-In2 Se3 nanosheets.