The Effect of Yoga on Intraocular Pressure Using the "iCare HOME2" Tonometer.

BACKGROUND: Various yoga positions may have an unfavorable impact on intraocular pressure (IOP) and may therefore be seen as a potential risk factor for the progression of glaucoma. The new "iCare HOME2" is a handheld self-tonometer for IOP measurements outside clinical settings. This is the first study to evaluate the immediate effect of common yoga postures on the IOP of healthy and glaucomatous eyes using the "iCare HOME2" self-tonometer and to compare the time of IOP recovery in both groups. METHODS: This is a single-center, prospective, observational study including 25 healthy and 25 glaucoma patients performing the following yoga positions: "legs up" (Viparita Karani), "bend over" (Uttanasana), "plough pose" (Halasana), and the "down face dog" (Adho Mukha Svanasana) for 90 s each, with a 2-min break in between. IOP was measured with the "iCare HOME2" before, during, and after each position. RESULTS: IOP significantly increased in all eyes in all positions (p < 0.05), showing no statistically significant difference between healthy or glaucomatous eyes (p > 0.05). The mean rise in IOP in healthy subjects was 1.6 mmHg (SD 1.42; p = 0.037), 14.4 mmHg (SD 4.48; p < 0.001), 7.5 mmHg (SD 4.21; p < 0.001), and 16.5 mmHg (SD 3.71; p < 0.001), whereas in glaucoma patients, IOP rose by 2.8 mmHg (SD 2.8; p = 0.017), 11.6 mmHg (SD 3.86; p < 0.001), 6.0 mmHg (SD 2.24; p < 0.001), and 15.1 mmHg (SD 4.44; p < 0.001) during the above listed yoga positions, repsectively. The highest increase in IOP was seen in the down face position, reaching mean IOP values above 31 mmHg in both study groups. IOP elevation was observed immediately after assuming the yoga position, with no significant change during the following 90 s of holding each pose (p > 0.05). All IOP values returned to baseline level in all individuals, with no significant difference between healthy and glaucoma participants. CONCLUSION: Our data show that common yoga positions can lead to an acute IOP elevation of up to 31 mmHg in healthy as well as glaucoma eyes, with higher IOP values during head-down positions. Given that IOP peaks are a major risk factor for glaucomatous optic neuropathy, we generally advise glaucoma patients to carefully choose their yoga exercises. If and to what extent practicing yoga leads to glaucoma progression, however, remains unclear and warrants further research.

Miniaturizing a Chip-Scale Spectrometer Using Local Strain Engineering and Total-Variation Regularized Reconstruction.

A wafer-thin chip-scale portable spectrometer suitable for wearable applications based on a reconstructive algorithm was demonstrated. A total of 16 spectral encoders that simultaneously functioned as photodetectors were monolithically integrated on a chip area of 0.16 mm2 by applying local strain engineering in compressively strained InGaN/GaN multiple quantum well heterostructures. The built-in GaN pn junction enabled a direct photocurrent measurement. A non-negative least-squares (NNLS) algorithm with total-variation regularization and a choice of a proper kernel function was shown to deliver a decent spectral reconstruction performance in the wavelength range of 400-645 nm. The accuracies of spectral peak positions and intensity ratios between peaks were found to be 0.97% and 10.4%, respectively. No external optics, such as collimation optics and apertures, were used, enabled by angle-insensitive light-harvesting structures, including an array of cone-shaped backreflectors fabricated on the underside of the sapphire substrate.

Artificial Pancreas With Carbohydrate Suggestion Performance for Unannounced and Announced Exercise in Type 1 Diabetes.

OBJECTIVE: To evaluate the safety and performance of a new multivariable closed-loop (MCL) glucose controller with automatic carbohydrate recommendation during and after unannounced and announced exercise in adults with type 1 diabetes (T1D). RESEARCH DESIGN AND METHODS: A randomized, 3-arm, crossover clinical trial was conducted. Participants completed a heavy aerobic exercise session including three 15-minute sets on a cycle ergometer with 5 minutes rest in between. In a randomly determined order, we compared MCL control with unannounced (CLNA) and announced (CLA) exercise to open-loop therapy (OL). Adults with T1D, insulin pump users, and those with hemoglobin (Hb)A1c between 6.0% and 8.5% were eligible. We investigated glucose control during and 3 hours after exercise. RESULTS: Ten participants (aged 40.8 ± 7.0 years; HbA1c of 7.3 ± 0.8%) participated. The use of the MCL in both closed-loop arms decreased the time spent <70 mg/dL of sensor glucose (0.0%, [0.0-16.8] and 0.0%, [0.0-19.2] vs 16.2%, [0.0-26.0], (%, [percentile 10-90]) CLNA and CLA vs OL respectively; P = 0.047, P = 0.063) and the number of hypoglycemic events when compared with OL (CLNA 4 and CLA 3 vs OL 8; P = 0.218, P = 0.250). The use of the MCL system increased the proportion of time within 70 to 180 mg/dL (87.8%, [51.1-100] and 91.9%, [58.7-100] vs 81.1%, [65.4-87.0], (%, [percentile 10-90]) CLNA and CLA vs OL respectively; P = 0.227, P = 0.039). This was achieved with the administration of similar doses of insulin and a reduced amount of carbohydrates. CONCLUSIONS: The MCL with automatic carbohydrate recommendation performed well and was safe during and after both unannounced and announced exercise, maintaining glucose mostly within the target range and reducing the risk of hypoglycemia despite a reduced amount of carbohydrate intake.Register Clinicaltrials.gov: NCT03577158.

Gunshot damage to monoplace hyperbaric chamber acrylic.

Introduction: Health care workers are vulnerable to workplace violence, including active shooter incidents. Little is known about how firearms could damage monoplace chamber acrylic and whether a breached pressurized chamber presents additional threat to the patient or bystanders. Methods: In a remote area where firearm discharge is permitted, we tested the durability of sections of monoplace hyperbaric chamber acrylic under various firearm discharges. Firearms were discharged at acrylic sections from a distance of 17 feet at 45 degrees and 10 degrees from perpendicular while wearing protective gear. Firearm calibers ranged from .22 caliber handgun to 5.56 mm AR-15 rifle. We also conducted similar testing on a monoplace hyperbaric chamber pressurized with >99% oxygen to a differential pressure of 14.7 psig (2.0 atmospheres absolute at sea level). Handguns were remotely fired at a distance of 12 feet from the chamber (30 degrees from perpendicular), while the rifles were fired at a distance of 60 feet from the chamber. Result: Higher-caliber handguns penetrated or fractured the acrylic sections only after multiple shots. The tested rifles caused full-thickness penetration and fracture with a single shot. However, the pressurized monoplace hyperbaric chamber required two shots from the AR-15 rifle, separated by approximately 60 mm, to penetrate the acrylic, resulting in rapid depressurization. The chamber otherwise remained intact, with no explosion or conflagration observed. Conclusion: An intact or pressurized chamber performs differently than stand-alone acrylic sections under firearms testing. In a worst-case active shooter scenario, the pressurized monoplace chamber tested posed no additional threat to bystanders beyond the significant risk of ricochet.

Current phototherapy practice on Java, Indonesia.

BACKGROUND: In Indonesia, the burden of severe hyperbilirubinemia is higher compared to other countries. Whether this is related to ineffective phototherapy (PT) is unknown. The aim of this study is to investigate the performance of phototherapy devices in hospitals on Java, Indonesia. METHODS: In 17 hospitals we measured 77 combinations of 20 different phototherapy devices, with and without curtains drawn around the incubator/crib. With a model to mimic the silhouette of an infant, we measured the irradiance levels with an Ohmeda BiliBlanket Meter II, recorded the distance between device and model, and compared these to manufacturers' specifications. RESULTS: In nine hospitals the irradiance levels were less than required for standard PT: < 10 µW/cm2/nm and in eight hospitals irradiance failed to reach the levels for intensive phototherapy: 30 µW/cm2/nm. Three hospitals provided very high irradiance levels: > 50 µW/cm2/nm. Half of the distances between device and model were greater than recommended. Distance was inversely correlated with irradiance levels (R2 = 0.1838; P < 0.05). The effect of curtains on irradiance levels was highly variable, ranging from - 6.15 to + 15.4 µW/cm2/nm, with a mean difference (SD) of 1.82 (3.81) µW/cm2/nm (P = 0.486). CONCLUSIONS: In half of the hospitals that we studied on Java the levels of irradiance are too low and, in some cases, too high. Given the risks of insufficient phototherapy or adverse effects, we recommend that manufacturers provide radiometers so hospitals can optimize the performance of their phototherapy devices.

Detection of high-frequency artifact as a function of pulse generator algorithms and outer-insulation material.

BACKGROUND: A high rate of malfunction, predominantly intermittent high-frequency artifacts (HFAs), has been recently reported in Abbott Medical Tendril pacing leads. OBJECTIVE: To investigate the factors associated with the occurrence of HFAs on Tendril leads using a commonly used comparator lead for a control. METHODS: We reviewed institutional data for Medtronic CapSureFix 5076 and Abbott Medical Tendril pace-sense leads retrospectively. Recordings deemed to be due to electromagnetic interference and far-field oversensing were not included in the classification of HFAs. RESULTS: A total of 7673 leads were analyzed: 1628 Optim-insulated Tendril leads, 825 non-Optim Tendril leads, and 5220 CapSureFix 5076. HFAs were seen in 212 leads and were more frequently observed in Tendril compared to CapSureFix leads during a mean follow-up of 4.1 ± 3.6 years. Lower age at implant, defibrillator systems, atrial position, and connection to an Abbott Medical generator were associated with increased HFA. In multivariable analysis, only connection to Abbott Medical generators (odds ratio 7.686, P < .001) and age (odds ratio 0.988 per year, P = .016) were independently associated with HFAs on pace-sense leads. In an Abbott-generator-only analysis, Optim-insulated Tendril leads were more likely to display HFAs than non-Optim Tendril leads but not Medtronic CapSureFix 5076 leads. CONCLUSION: Abbott Medical pulse generators independently predict HFA in Tendril and CapSureFix 5076 leads, likely the result of displaying short or low-amplitude noise episodes that other devices do not record. When restricted to Abbott generators only, Optim-insulated Tendril leads show an increased incidence of HFAs when compared to non-Optim Tendril leads but not CapSureFix 5076 leads.

Cardiac implantable electronic devices in adults with tetralogy of Fallot.

BACKGROUND: Tachyarrhythmias and bradyarrhythmias affect 20%-50% of adult patients with tetralogy of Fallot (TOF) and some of these patients will require cardiac implantable electronic devices (CIED) such as pacemaker and/or internal cardioverter defibrillator. METHODS: The Mayo Adult Congenital Heart Disease database was queried for patients with repaired TOF and history of CIED implantation, 1990-2017. The study objectives were: (1) determine the occurrence of device-related complications defined as lead failure, lead recall, device infection and lead thrombus; and (2) determine the occurrence and risk factors for defibrillator shock. RESULTS: There were 99 patients (age 46±14 years and 66 (66%) men) with CIED, and the CIEDs were 41 (41%) pacemakers and 73 (73%) defibrillators. Indication for defibrillator implantation was for primary prevention in 28 (38%) and secondary prevention in 45 (62%). Device-related complications occurred in 20 (20%) patients (lead failure 17, lead recall 4, device infection 12 and thrombus 3). Twenty-five per cent of all device infections occurred within 30 days from the time of device generator change. Annualised rates of appropriate and inappropriate shocks were 5.7% and 6.2%, respectively. The use of class III antiarrhythmic drug was protective against defibrillator shock. CONCLUSION: The current study provides useful outcome data to aid patient counselling and clinical decision-making. Further studies are required to explore ways to decrease the risk of postprocedural infection after device generator change, and to determine which patients will benefit from empirical antiarrhythmic therapy as a strategy to decrease incidence of inappropriate defibrillator shock.

Sudden-onset severe presyncope in a 67-year-old man.

A 67-year-old man presented to the emergency department with sudden onset of severe presyncope. He reported that he had a permanent pacemaker implanted in 2006 following atrioventricular node ablation for persistent atrial fibrillation (AF). After suffering increasing shortness of breath, he underwent upgrade to cardiac resynchronisation therapy (CRT) in 2016. He denied any recent falls, interventions or changes in medication. ECG monitoring showed AF with a broad ventricular escape rhythm at around 25 bpm with pauses of up to 3 s. Placement of a magnet over the device resulted in pacing (figure 1A). The implanted device (Medtronic Syncra C2TR01) was interrogated (figure 1B), and a chest radiograph was obtained (figure 2). heartjnl;105/8/657/F1F1F1Figure 1(A) Twelve-lead ECG demonstrating intrinsic rhythm and pacing after application of magnet. (B) Device interrogation with right ventricular threshold test. heartjnl;105/8/657/F2F2F2Figure 2(C) Anteroposterior chest radiograph demonstrating lead position on admission. QUESTION: What was the cause of this presentation?Noise oversensing on the right ventricular (RV) lead due to lead fracture.The RV septal lead has displaced into the right atrial (RA).RA and RV leads were switched in the can during the CRT upgrade.Increase in threshold of RV and left ventricular (LV) leads resulting in loss of capture.

Non-calorimetric determination of absorbed power during magnetic nanoparticle based hyperthermia.

Nanomagnetic hyperthermia (NMH) is intensively studied with the prospect of cancer therapy. A major challenge is to determine the dissipated power during in vivo conditions and conventional methods are either invasive or inaccurate. We present a non-calorimetric method which yields the heat absorbed during hyperthermia: it is based on accurately measuring the quality factor change of a resonant radio frequency circuit which is employed for the irradiation. The approach provides the absorbed power in real-time, without the need to monitor the sample temperature as a function of time. As such, it is free from the problems caused by the non-adiabatic heating conditions of the usual calorimetry. We validate the method by comparing the dissipated power with a conventional calorimetric measurement. We present the validation for two types of resonators with very different filling factors: a solenoid and a so-called birdcage coil. The latter is a volume coil, which is generally used in magnetic resonance imaging (MRI) under in vivo condition. The presented method therefore allows to effectively combine MRI and thermotherapy and is thus readily adaptable to existing imaging hardware.

Can the Application of Multi-Mode Adhesive be a Substitute to Silicatized/Silanized Y-TZP Ceramics?

This study evaluated the effectiveness of a multi-mode adhesive (SBU-Scotch Bond Universal/3M) as a substitute for silica coating and silane application on the bonding of zirconia ceramics to resin cement. One-hundred and twenty sintered zirconia ceramic blocks (5 x 5 x 5 mm) were obtained, finished by grounding with silicon carbide paper (#600, #800, #1000 and #1200) and randomly divided into 12 groups (n=10) in accordance with the factors "surface treatment" (ScSi - silicatization + silanization; ScSBU - silicatization + SBU; SBU - SBU without photoactivation and SBUp - SBU photoactivated) and "ceramic" (Lava / 3M ESPE, Ceramill Zirconia / Amann Girrbach and Zirkonzahn / Zirkonzahn). Dual resin cement cylinders (RelyX Ultimate/3M ESPE) were subsequently produced in the center of each block using a silicon matrix (Ø=2 mm, h=5 mm) and photoactivated for 40 s (1200 mW/cm2). The samples were stored for 30 days in distilled water (37ºC) and submitted to shear bond strength test (1 mm/min, 100 KgF). Data (MPa) were analyzed under ANOVA (2 levels) and Tukey test (5%). Complementary analyzes were also performed. ANOVA revealed that only the factor "surface treatment" was significant (p=0.0001). The ScSi treatment (14.28A) promoted statistically higher bond strength values than the other ScSBU (9.03B), SBU (8.47B) and SBUp (7.82B), which were similar to each other (Tukey). Failure analysis revealed that 100% of the failures were mixed. The silica coating followed by the silanization promoted higher bond strength values of resin cement and ceramic, regardless of the zirconia ceramic or SBU.

Time to augment?! Impact of cement augmentation on pedicle screw fixation strength depending on bone mineral density.

PURPOSE: Cement augmentation of pedicle screws is known to increase their mechanical strength. Aim was to evaluate the impact of cement augmentation on pedicle screw fatigue strength in dependence of the bone mineral density (BMD). METHODS: Twenty-one human L2 vertebral bodies from donors between 19 and 96 years of age were used for in vitro experiments. BMD was measured using quantitative computed tomography (QCT). Two pedicle screws were inserted in each specimen and unilaterally augmented with bone cement. Fatigue testing was performed using a cranio-caudal sinusoidal, cyclic load (0.5 Hz) with increasing compression force (100 N + 0.1 N/cycles). Results were evaluated for the BMD groups: normal: BMD > 120 mg/cm3, osteopenic: BMD 80-120 mg/cm3, and osteoporotic: BMD < 80 mg/cm3 bone mass. RESULTS: There was a significant correlation between fatigue force and BMD for the non-augmented and augmented screws (non-augmented R2 = 0.839, p < 0.001; augmented R2 = 0.551, p < 0.001). There was a significantly increased fatigue strength of the augmented screws over the non-augmented screws in the osteoporotic group (p = 0.001), while the differences in the other groups were not significant (normal p = 0.818/osteopenic p = 0.132). CONCLUSIONS: The benefit of pedicle screw cement augmentation significantly depends on the bone mineral density and has the greatest extent of increased fatigue strength in osteoporotic vertebrae. Preoperative measurement of the BMD is strongly recommended to predict the benefit of augmentation and reinforce the decision for cement augmentation. These slides can be retrieved under Electronic Supplementary Material.

Inhibition and restoration of CRT pacing - What is the mechanism?

The electrocardiogram (ECG) interpretation in patients with cardiac resynchronization therapy (CRT) may be challenging. The difficulty increases if not well-known pacemaker algorithm is turned on. We show a T-wave protection algorithm (LVTP) in a patient with CRT. Accelerated sinus rhythm and intermittent oversensing in left ventricular channel resulted in loss of CRT pacing. The restoration of biventricular pacing occurred when atrial rate decreased. We provide detailed descriptions of the electrocardiogram and intracardiac electrogram. LVTP may confuse ECG examination interpretation, especially in patients with accelerated atrial rhythm and oversensing in left ventricular channel.

Can the application of multi-mode adhesive be a substitute to silicatized/silanized y-tzp ceramics?

Abstract This study evaluated the effectiveness of a multi-mode adhesive (SBU-Scotch Bond Universal/3M) as a substitute for silica coating and silane application on the bonding of zirconia ceramics to resin cement. One-hundred and twenty sintered zirconia ceramic blocks (5 x 5 x 5 mm) were obtained, finished by grounding with silicon carbide paper (#600, #800, #1000 and #1200) and randomly divided into 12 groups (n=10) in accordance with the factors "surface treatment" (ScSi - silicatization + silanization; ScSBU - silicatization + SBU; SBU - SBU without photoactivation and SBUp - SBU photoactivated) and "ceramic" (Lava / 3M ESPE, Ceramill Zirconia / Amann Girrbach and Zirkonzahn / Zirkonzahn). Dual resin cement cylinders (RelyX Ultimate/3M ESPE) were subsequently produced in the center of each block using a silicon matrix (Ø=2 mm, h=5 mm) and photoactivated for 40 s (1200 mW/cm2). The samples were stored for 30 days in distilled water (37ºC) and submitted to shear bond strength test (1 mm/min, 100 KgF). Data (MPa) were analyzed under ANOVA (2 levels) and Tukey test (5%). Complementary analyzes were also performed. ANOVA revealed that only the factor "surface treatment" was significant (p=0.0001). The ScSi treatment (14.28A) promoted statistically higher bond strength values than the other ScSBU (9.03B), SBU (8.47B) and SBUp (7.82B), which were similar to each other (Tukey). Failure analysis revealed that 100% of the failures were mixed. The silica coating followed by the silanization promoted higher bond strength values of resin cement and ceramic, regardless of the zirconia ceramic or SBU.

Resumo Este estudo avaliou a efetividade de um adesivo "multi-mode" (Single Bond Universal/3M) como um substituto para a silicatização e aplicação do silano na resistência de união das cerâmicas de zircônia e um cimento resinoso. Para isso, 120 blocos cerâmicos sinterizados de zircônia nas dimensões de (5 x 5 x 5 mm) foram obtidos, lixados com lixas de granulação decrescente (#600, #800, #1000 e #1200) e divididos aleatoriamente em 12 grupos (n = 10), de acordo com os fatores "tratamento de superfície" (ScSi - silicatização + silanização; ScSBU - silicatização + Single Bond; SBU - SBU sem fotoativação e SBUp - SBU com fotoativação) e "cerâmica" (Lava/3M ESPE, Ceramill Zircônia/ Amann Girrbach e Zirkonzahn/Zirkonzahn). Posteriormente, cilindros de cimento resinoso dual (RelyX Ultimate/3M ESPE) foram confeccionados no centro de cada bloco com auxílio de uma matriz de silicone (Ø=2 mm; h=5 mm) e fotopolimerizados por 40 s (1200 mW/ cm²). Em seguida, as amostras foram armazenadas durante trinta dias em água destilada (37 °C) e submetidas ao ensaio de resistência de união ao cisalhamento (1 mm/min, 100 kgF). Os dados (MPa) foram analisados sob ANOVA (2 fatores) e teste de Tukey (5%). Análises complementares também foram realizadas. ANOVA revelou que apenas o fator "tratamento de superfície" foi significativo (p=0,0001). O tratamento ScSi (14.28A) promoveu valores de adesão estatisticamente superiores aos demais ScSBU (9.03B), SBU (8.47B) e SBUp (7.82B), os quais foram semelhantes entre si (Tukey). A Análise de falhas revelou que 100% da falhas que ocorreram foram mistas. A silicatização seguida da silanização promoveu a melhor resistência de união entre cimento resinoso e a cerâmica, independentemente do tipo da cerâmica ou do SBU.

High-Dose TL Dosimetry of Reactor Neutrons.

Radiation dose was measured with set of TL dosimeters during checkout of neutron radiation hardness of the ORTEC preamplifier type 142A in the experiment at the MARIA nuclear reactor at the National Centre for Nuclear Research (NCBJ), Otwock-Swierk, Poland. Different types of LiF-based TL detectors have been used for measurements in order to evaluate neutron and non-neutron components of the radiation field in the reactor channel during exposure and to check their relevancy for dose measurements in the reactor environment. For high-dose evaluation a new Ultra-High-Temperature Ratio (UHTR) method established for highly sensitive LiF:Mg,Cu,P detectors has been applied. Neutron fluence evaluated from TL measurements was in good agreement with one calculated using neutron flux data during the experiment.

Stroke: ineffective tube securement reduces nutrition and drug treatment.

Stroke patients with dysphagia often depend on nutrition, hydration and medication via nasogastric (NG) feeding tubes. Securing tubes using tape is associated with repeated tube loss. In this study, the authors determined cause and effect by auditing tube placement methods, delays incurred, duration and costs. Of 202 NG tube placements in 75 patients, 67 placements occurred in 17 patients over a full course of enteral nutrition (EN) and 40 of these placements were tracked. Tubes were secured by tape in 100%, mittens 31% and special observation 5.4%. However, over an EN course, inadvertent tube loss occurred in 82% of patients and was associated with age (p=0.049) and mitten use (p<0.001): 64% of tubes were lost due to patients and 9% slipped. Average 'tube life' was 2 days, less than 25% of the EN episode (p<0.001). While tube placement occurred within 2.55 hours of request, X-ray confirmation led to a delay in feed and drugs of 8-9 hours per tube placement and loss of 18.8% of feeding time per EN episode. Delays exceeded the 1-hour and 4-hour limits for antibiotics and other medicines in 20% and 80%, respectively. In the 17 tracked patients, it was estimated that 55% of the £5979 direct costs could be saved by nasal bridle use. In conclusion, most tubes studied were lost to inadvertent tube removal, leading to clinically significant delays to nutrition, hydration and drug treatments; this may impair recovery. Reducing tube loss is likely to reduce patient distress, treatment cost and enhance recovery.

In Vitro Evaluation of the Fresenius Kabi CATSmart Autotransfusion System.

Use of autotransfusion systems to collect, wash, and concentrate shed blood during surgical procedures is a widely used method for reducing postoperative anemia and the need for blood transfusions. The aim of this study was to evaluate the CATSmart Continuous Autotransfusion System wash program performance with small (200 or 700 mL) and large volumes (1,000 mL) of shed blood and to determine non-inferiority of the CATSmart to the C.A.T.S plus system. Human whole blood was collected in citrate phosphate dextrose, diluted, and divided into two aliquots to be processed as a pair using the C.A.T.S plus and CATSmart systems with their corresponding wash programs: low-volume, high quality/smart, or emergency wash. Final packed red cell product was analyzed for red blood cell (RBC), white blood cell, and platelet counts; hemoglobin; hemolysis; RBC recovery rates; and elimination of albumin, total protein, and potassium. The mean hematocrit (HCT) after processing with CATSmart and C.A.T.S plus systems were 59.63% and 57.71%, respectively. The calculated overall RBC recovery rates on the CATSmart and C.A.T.S plus systems were 85.41% and 84.99%, respectively. Elimination of albumin (97.5%, 98.0%), total proteins (97.1%, 97.5%), and potassium (92.1%, 91.9%) were also calculated for the CATSmart and C.A.T.S plus systems. The CATSmart and C.A.T.S plus systems both provided a high-quality product in terms of HCT, protein elimination, and hemolysis rates across the range of tested shed blood volumes and all wash programs. The study was able to confirm the CATSmart is non-inferior to the C.A.T.S plus system.

Biosynthesis of silver nanoparticles using Artemisia annua callus for inhibiting stem-end bacteria in cut carnation flowers.

A biological method for synthesising silver nanoparticles (AgNPs) was developed using the callus extracts from Artemisia annua L. under sunlight at 25,000 lx. The AgNPs were characterised using transmission electron microscopy, atomic force microscope, X-ray diffraction and Fourier transform infrared spectroscopy. The AgNPs were mostly spherical with the size of 2.1 to 45.2 nm (average 10.9 nm). Pulse treatments of AgNPs at 125, 250 and 500 mg/l for 1 h extended vase life of cut carnation (Dianthus caryophyllus cv. Green Land) flowers. Four dominant bacteria strains Arthrobacter arilaitensis, Kocuria sp., Staphylococcus equorum and Microbacterium oxydans were isolated from the stem-ends of cut D. caryophyllus flowers. AgNP pulse inhibited significantly bacterial growth in vase solution and cut stem ends during all of the vase period. The bacteria related blockage in the stem-ends was significantly alleviated by AgNP pulse because of its higher antibacterial efficacy against the dominant bacteria. In addition, ethylene release of cut carnation flowers was inhibited in response to AgNP pulse. This is the first time that the biologically synthesised AgNPs could be applied as a promising preservative agent for cut carnation flowers.

Novel synthesis and characterization of pristine Cu nanoparticles for the non-enzymatic glucose biosensor.

Non enzymatic electrochemical glucose sensing was developed based on pristine Cu Nanopartilces (NPs)/Glassy Carbon Electrode (GCE) which can be accomplished by simple green method via ocimum tenuiflorum leaf extract. Then, the affect of leaf extract addition on improving Structural, Optical and electrochemical properties of pristine cu NPs was investigated. The synthesized Cu NPs were characterized with X-ray diffraction (X-ray), Uv-Visible spectroscopy (Uv-Vis), Fourier transformation infrared spectroscopy (FTIR), Particle size distribution (PSA), Scanning electron microscopy (SEM), Energy dispersive X-ray spectroscopy (EDS), Transmission electron microscopy (TEM) for structural optical and morphological studies respectively. The synthesized Cu NPs were coated over glassy carbon electrode (GCE) to study the electrochemical response of glucose by cyclic voltammetry and ampherometer. The results indicates that the modified biosensor shows a remarkable sensitivity (1065.21 µA mM-1 cm-2), rapid response time (<3s), wide linear range (1 to 7.2 mM), low detection limit (0.038 µM at S/N = 3). Therefore, the prepared Cu NPs by the Novel Bio-mediated route were exploited to construct a non-enzymatic glucose biosensor for sustainable clinical field applications.

Magneto-therapy of human joint cartilage.

PURPOSE: The topic of the present paper concerns the human joint cartilage therapy performed by the magnetic induction field. There is proved the thesis that the applied magnetic field for concrete cartilage illness should depend on the proper relative and concrete values of applied magnetic induction, intensity as well the time of treatment duration. Additionally, very important are frequencies and amplitudes of magnetic field as well as magnetic permeability of the synovial fluid. MATERIAL AND METHODS: The research methods used in this paper include: magnetic induction field produced by a new Polish and German magneto electronic devices for the therapy of human joint cartilage diseases, stationary and movable magnetic applicators, magnetic bandage, ferrofluid injections, author's experience gained in Germany research institutes and practical results after measurements and information from patients. RESULTS: The results of this paper concern concrete parameters of time dependent electro-magnetic field administration during the joint cartilage therapy duration and additionally concern the corollaries which are implied from reading values gained on the magnetic induction devices. CONCLUSIONS: The main conclusions obtained in this paper are as follows: Time dependent magnetic induction field increases the dynamic viscosity of movable synovial fluid and decreases symptoms of cartilage illness for concrete intensity of magnetic field and concrete field line architecture. The ferrofluid therapy and phospholipids bilayer simultaneously with the administrated external electromagnetic field, increases the dynamic viscosity of movable synovial fluid.

Modulation and modeling of monoclonal antibody N-linked glycosylation in mammalian cell perfusion reactors.

Mammalian cell perfusion cultures are gaining renewed interest as an alternative to traditional fed-batch processes for the production of therapeutic proteins, such as monoclonal antibodies (mAb). The steady state operation at high viable cell density allows the continuous delivery of antibody product with increased space-time yield and reduced in-process variability of critical product quality attributes (CQA). In particular, the production of a confined mAb N-linked glycosylation pattern has the potential to increase therapeutic efficacy and bioactivity. In this study, we show that accurate control of flow rates, media composition and cell density of a Chinese hamster ovary (CHO) cell perfusion bioreactor allowed the production of a constant glycosylation profile for over 20 days. Steady state was reached after an initial transition phase of 6 days required for the stabilization of extra- and intracellular processes. The possibility to modulate the glycosylation profile was further investigated in a Design of Experiment (DoE), at different viable cell density and media supplement concentrations. This strategy was implemented in a sequential screening approach, where various steady states were achieved sequentially during one culture. It was found that, whereas high ammonia levels reached at high viable cell densities (VCD) values inhibited the processing to complex glycan structures, the supplementation of either galactose, or manganese as well as their synergy significantly increased the proportion of complex forms. The obtained experimental data set was used to compare the reliability of a statistical response surface model (RSM) to a mechanistic model of N-linked glycosylation. The latter outperformed the response surface predictions with respect to its capability and reliability in predicting the system behavior (i.e., glycosylation pattern) outside the experimental space covered by the DoE design used for the model parameter estimation. Therefore, we can conclude that the modulation of glycosylation in a sequential steady state approach in combination with mechanistic model represents an efficient and rational strategy to develop continuous processes with desired N-linked glycosylation patterns. Biotechnol. Bioeng. 2017;114: 1978-1990. © 2017 Wiley Periodicals, Inc.