Design and evaluation of mucoadhesive beads of glipizide as a controlled release drug delivery system.

The present work aims at the development of a low-cost controlled release system of glipizide beads embedded in pectin to overcome the problem of frequent dosing of drug. The method of preparation has been optimised by experimental design to achieve satisfactory responses with respect to controlling variables. The controlling variables are X1, drug-polymer ratio; X2, surfactant concentration and X3, isooctane-acetone ratio. The most effective combination is X1(1:6), X2(1%), X3(50:50). Various parameters such as mucoadhesivity and swellability of beads, characterisation, dissolution, stability, ex vivo absorption and in vivo (Oral glucose tolerance test in rat) studies were performed with the optimised product. The optimised product was found quiet satisfactory that showed yield of 86.78%, drug entrapment efficiency (DEE) of 87.38% and drug release was extended up to 18 h. The present formulation of glipizide is a promising multiparticulate system of glipizide with significant hypoglycemic effect, and moreover it was prepared rapidly with ease.

[Applicability of a natural swelling matrix as the propellant of osmotic pump tablets].

The purpose of this study is to investigate the applicability of a natural swelling matrix derived from boat-fruited sterculia seed (SMS) as the propellant of osmotic pump tablets. The sugar components, static swelling, water uptake and viscosity of SMS were determined and compared with that of polythylene oxide (WSR-N10 and WSR-303). Both ribavirin and glipizide were used as water-soluble and water-insoluble model drugs. Then, the monolayer osmotic pump tablets of ribavirin and the bilayer osmotic pump tablets of glipizide were prepared using SMS as the osmotically active substance and propellant. SMS was mainly composed of rhamnose, arabinose, xylose and galactose and exhibited relatively high swelling ability. The area of the disintegrated matrix tablet was 20.1 times as that at initial after swelling for 600 s. SMS swelled rapidly and was fully swelled (0.5%) in aqueous solution with relative low viscosity (3.66 +/- 0.03) mPa x s at 25 degrees C. The monolayer osmotic pump tablets of ribavirin and the bilayer osmotic pump tablets of glipizide using SMS as propellant exhibited typical drug release features of osmotic pumps. In conclusion, the swelling matrix derived from boat-fruited sterculia seed, with low viscosity and high swelling, is a potential propellant in the application of osmotic pump tablets.

Formulation and evaluation of mucoadhesive glipizide microspheres.

The purpose of this research was to formulate and systematically evaluate in vitro and in vivo performances of mucoadhesive microspheres of glipizide. Glipizide microspheres containing chitosan were prepared by simple emulsification phase separation technique using glutaraldehyde as a cross-linking agent. Results of preliminary trials indicate that volume of cross-linking agent, time for cross-linking, polymer-to-drug ratio, and speed of rotation affected characteristics of microspheres. Microspheres were discrete, spherical, and free flowing. The microspheres exhibited good mucoadhesive property in the in vitro wash-off test and also showed a high percentage drug entrapment efficiency. A 3(2) full factorial design was employed to study the effect of independent variables, polymer-to-drug ratio (X(1) ), and stirring speed (X(2) ) on dependent variables percentage mucoadhesion, t(80), drug entrapment efficiency, and swelling index. The best batch exhibited a high drug entrapment efficiency of 75% and a swelling index of 1.42; percentage mucoadhesion after 1 hour was 78%. The drug release was also sustained for more than 12 hours. The polymer-to-drug ratio had a more significant effect on the dependent variables. In vivo testing of the mucoadhesive microspheres to albino Wistar rats demonstrated significant hypoglycemic effect of glipizide.

Evaluation of bioadhesive glipizide spheres and compacts from spheres prepared by extruder/marumerizer technique.

The objective of this study was to attempt to deliver glipizide from spheres and compacts containing the natural polymer Carrageenan (Gelcarin, GP 812) and prepared by extruder/marumerizer technique. A second objective was to evaluate the mucoadhesive strength of the bioadhesive spheres onto the mucus membrane of rabbit. The effects of polymer, drug level, and type of spheronizing material were evaluated. All sphere formulations were compacted into tablets using a rotary Manesty B-3B machine equipped with 12/32 flat face tooling. Results show drug release from spheres and compacts decreased as the level of Carrageenan was increased. However as the level of drug was increased drug release also increased. Spheres containing Avicel PH-101 gave higher drug release than spheres of the same composition but prepared with Avicel RC-581. In general, the drug release from tablets was higher than its corresponding spheres and drug release from spheres and tablets containing Carrageenan was higher than control spheres and tablets of the same composition but without Carrageenan. Tablet formulations compacted from spheres containing Avicel RC-581 gave higher release rate constants than tablet formulations of the same composition but prepared with Avicel PH-101. The bioadhesion study showed that mucoadhesion strength between spheres and mucus membrane of the rabbit depends on the levels of polymer, drug, and type of spheronizing material. Developed bioadhesive spheres and tablets increase the solubility of glipizide which may increase its bioavailability and also increased the adherence of the bioadhesive systems to the mucous membrane so that once daily dose can be administered.