Real-time, in situ DNA hybridization detection with attomolar sensitivity without amplification using (pb(Mg1/3Nb2/3)O3)0.65-(PbTiO3)0.35 piezoelectric plate sensors.

In this paper we have investigated real-time, in situ DNA hybridization detection using piezoelectric plate sensors (PEPSs) consisting of a highly piezoelectric lead magnesium niobate-lead titanate (PMN-PT) layer 8µm in thickness thinly coated with Cr/Au electrodes and electrically insulated with 3-mercaptopropyltrimethoxysilane (MPS) encapsulation. With probe complementary DNA (cDNA) immobilized on the PEPS surface and by monitoring the first longitudinal extension mode (LEM) resonance frequency shift of the PEPS we detected hybridization of the target DNA (tDNA) to the probe cDNA on the PEPS surface in real time at concentration 1.6×10(-18)M with a signal to noise ratio of 8 without isolation and amplification at room temperature in 30min in phosphate buffered saline (PBS) solution. The detection was validated in situ by two different methods: (1) the detection of fluorescently labeled microspheres coated with reporter cDNA complementary to the tDNA but different from the probe cDNA; (2) fluorescent visualization.

The MainSTREAM component platform: a holistic approach to microfluidic system design.

A microfluidic component library for building systems driving parallel or serial microfluidic-based assays is presented. The components are a miniaturized eight-channel peristaltic pump, an eight-channel valve, sample-to-waste liquid management, and interconnections. The library of components was tested by constructing various systems supporting perfusion cell culture, automated DNA hybridizations, and in situ hybridizations. The results showed that the MainSTREAM components provided (1) a rapid, robust, and simple method to establish numerous fluidic inputs and outputs to various types of reaction chips; (2) highly parallel pumping and routing/valving capability; (3) methods to interface pumps and chip-to-liquid management systems; (4) means to construct a portable system; (5) reconfigurability/flexibility in system design; (6) means to interface to microscopes; and (7) compatibility with tested biological methods. It was found that LEGO Mindstorms motors, controllers, and software were robust, inexpensive, and an accessible choice as compared with corresponding custom-made actuators. MainSTREAM systems could operate continuously for weeks without leaks, contamination, or system failures. In conclusion, the MainSTREAM components described here meet many of the demands on components for constructing and using microfluidics systems.

Morpholino-functionalized silicon nanowire biosensor for sequence-specific label-free detection of DNA.

We investigated Morpholino-functionalized silicon nanowires (SiNWs) as a novel gene chip platform for the sequence-specific label-free detection of DNA. Morpholino attachment and subsequent Morpholino-DNA hybridization on silicon surface was characterized by X-ray photoelectron spectroscopy and fluorescence microscopy. The resultant Morpholino-modified surfaces showed high specificity of recognition for DNA. Subsequently, by using the same protocol, the surface of the SiNW biosensor was functionalized with Morpholino, and this was used for label-free Morpholino-DNA hybridization detection. Real-time measurements of the Morpholino-functionalized SiNW biosensor exhibited a decrease in a time-dependent conductance when complementary and mutant DNA samples were added. Furthermore, identification of fully complementary versus mismatched DNA samples was carried out by the Morpholino-functionalized SiNW biosensor. We demonstrated that DNA detection using the Morpholino-functionalized SiNW biosensor could be carried out to the hundreds of femtomolar range. The Morpholino-functionalized SiNWs show a novel biosensor for label-free and direct detection of DNA with good selectivity, and a promising application in gene expression.

An enzyme-amplified amperometric DNA hybridisation assay using DNA immobilised in a carboxymethylated dextran film anchored to a graphite surface.

This report describes a simple methodology for preparation of an enzyme-amplified amperometric DNA hybridisation assay using solution-phase ferrocenemethanol mediation of glucose oxidase oxidation of glucose. The recognition layer consists of amine-terminated ssDNA (designed for binding of the sequence ssrA gene of Listeria monocytogenes) bound within a carboxymethylated dextran film that is anchored to a graphite electrode. Anchoring sites are provided by electrochemical grafting of an arylamine to the carbon surface following in situ diazotisation of p-phenylenediamine. Hybridisation between the immobilised probe ssDNA and a biotin-labelled target ssDNA sequence is detected by following the oxidation of glucose upon addition of a glucose oxidase-avidinD conjugate and ferrocenemethanol. The stability of the anchored film permits washing and blocking steps to discriminate between hybridisation and non-specific binding. The signal current, measured by cyclic voltammetry and constant potential amperometry, scales with biotin-complementary DNA concentration, from 2.5x10(-6) M to 3x10(-7) M and a detection limit of 0.2 nmol in the 500 microL sample at the 3-mm diameter graphite electrode is estimated. Approaches to improve upon the analytical performance of this simple assay are highlighted.

Anodized aluminum oxide-based capacitance sensors for the direct detection of DNA hybridization.

We fabricated a capacitance sensor based on an anodized aluminum oxide (AAO) nanoporous structure to detect DNA hybridization. We utilized Au film deposited on the surface of the AAO membrane and Au nanowires infiltrating the nanopores as the top and bottom electrodes, respectively. When completely complementary target DNA molecules were added to the sensor-immobilized DNA molecule probes, the capacitance was reduced; with a concentration of 1pM, the capacitance decreased by approximately 10%. We measured the capacitance change for different concentrations of the target DNA solution. A linear relationship was found between the capacitance change and DNA concentration on a semi-logarithmic scale. We also investigated the possibility of detecting DNA molecules with a single-base mismatch to the probe DNA molecule. In contrast to complementary target DNA molecules, the addition of one-base mismatch DNA molecules caused no significant change in capacitance, demonstrating that DNA hybridization was detected with single nucleotide polymorphism sensitivity.

Highly sensitive measurements of PNA-DNA hybridization using oxide-etched silicon nanowire biosensors.

The highly sensitive and sequence-specific detection of single-stranded oligonucleotides using nonoxidized silicon nanowires (SiNWs) is demonstrated. To maximize device sensitivity, the surface of the SiNWs was functionalized with a densely packed organic monolayer via hydrosilylation, subsequently immobilized with peptide nucleic acid (PNA) capable of recognizing the label-free complementary target DNA. Because of the selective functionalization of the SiNWs, binding competition between the nanowire and the underlying oxide is avoided. Transmission electron microscopy was conducted to clearly differentiate the SiNW surface before and after removal of SiO(2). Fluorescence microscopy was used to further realize the selectivity of the oxide-etched chemistry on the SiNWs and sequence specificity of PNA-DNA hybridization. The concentration-dependent resistance change measurements upon hybridization of PNA-DNA show that detection limit down to 10fM can be obtained. The SiNW devices also reveal the capability of an obvious discrimination against mismatched sequences. Among several efforts being made to improve detection sensitivity, this work addresses one significant issue regarding surface functionalization which enables highly sensitive biomolecular sensing with SiNWs.

DNA immobilisation procedures for surface plasmon resonance imaging (SPRI) based microarray systems.

Two different surface chemistries have been studied for the development of surface plasmon resonance imaging (SPRI) based DNA microarray affinity sensors: (1) 11-mercaptoundecanoic acid-poly(ethylenimine) (MUA-PEI) and (2) dextran procedures. The MUA-PEI method consists of assembling a multilayer on the basis of electrostatic interactions formed with: 11-mercaptoundecanoic acid (MUA), poly(ethylenimine) (PEI) and extravidin layers. The dextran procedure involves assembling a multilayer formed with 11-mercaptoundecanol, dextran and streptavidin layers, which are linked by covalent bonds. The oligonucleotide probes are immobilised onto the sensor surface as spots forming a matrix 14x14, which is spotted by a robot, while the target sequences are free in solution. The system allows the interaction (hybridisation) monitoring, in real-time and in parallel, of unlabeled oligonucleotide solution targets to oligonucleotide probes immobilised on a 196 spots matrix. Using oligonucleotides as probes and targets, both functionalised surfaces have been evaluated in view of their application to the diagnosis of gene mutations involved in human diseases. In particular, we demonstrate the ability to detect, in parallel, several mutations causing human cystic fibrosis (CF), which lie within exon 10 of the human cystic fibrosis transmembrane conductance regulator (CFTR) gene. The immobilised probes were complementary to sequences corresponding the mutant or wild type alleles. Two deletions of three bases (DeltaF508 and DeltaI507) and four single nucleotide polymorphisms (M470V, Q493X, V520F and 1716 G>A) were investigated. In both functionalised surfaces, the system showed the capacity to discriminate normal and mutant sequences differing by a single base.

Label-free DNA sensors using ultrasensitive diamond field-effect transistors in solution.

Charge detection biosensors have recently become the focal point of biosensor research, especially field-effect-transistors (FETs) that combine compactness, low cost, high input, and low output impedances, to realize simple and stable in vivo diagnostic systems. However, critical evaluation of the possibility and limitations of charge detection of label-free DNA hybridization using silicon-based ion-sensitive FETs (ISFETs) has been introduced recently. The channel surface of these devices must be covered by relatively thick insulating layers ( SiO2, Si3N4, Al2O3, or Ta2O5) to protect against the invasion of ions from solution. These thick insulating layers are not suitable for charge detection of DNA and miniaturization, as the small capacitance of thick insulating layers restricts translation of the negative DNA charge from the electrolyte to the channel surface. To overcome these difficulties, thin-gate-insulator FET sensors should be developed. Here, we report diamond solution-gate FETs (SGFETs), where the DNA-immobilized channels are exposed directly to the electrolyte solution without gate insulator. These SGFETs operate stably within the large potential window of diamond (>3.0 V). Thus, the channel surface does not need to be covered by thick insulating layers, and DNA is immobilized directly through amine sites, which is a factor of 30 more sensitive than existing Si-ISFET DNA sensors. Diamond SGFETs can rapidly detect complementary, 3-mer mismatched (10 pM) and has a potential for the detection of single-base mismatched oligonucleotide DNA, without biological degradation by cyclically repeated hybridization and denature.

Visual DNA microarrays for simultaneous detection of Ureaplasma urealyticum and Chlamydia trachomatis coupled with multiplex asymmetrical PCR.

Visual DNA microarrays, based on gold label silver stain (GLSS) and coupled with multiplex asymmetrical PCR, were developed for simultaneous, sensitive and specific detection of Ureaplasma urealyticum and Chlamydia trachomatis. 5'-end-amino-modified oligonucleotides, which were immobilized on glass surface, acted as capturing probes that were designed to bind complementary biotinylated targets DNA. The gold-conjugated streptavidins were introduced to the microarray for specific binding to biotin. The black image of microarray spots, resulting from the precipitation of silver onto nanogold particles bound to streptavidins, were used to detect biotinylated targets DNA visually or with a visible light scanner. Multiplex asymmetrical PCR of U. urealyticum, C. trachomatis and Bacillus subtilis (used as positive control) was performed to prepare abundant biotinylated single-stranded targets DNA, which affected detection efficiency and sensitivity of hybridization on microarray. Plenty of clinical samples of U. urealyticum and C. trachomatis from infected patients were tested using home-made DNA microarrays. For its high sensitivity, good specificity, simplicity, cheapness and speed, the present visual gene-detecting technique has potential applications in clinical fields.

DNA hybridization detection on electrical microarrays using coulostatic pulse technique.

We demonstrated a novel application of transient coulostatic pulse technique for the detection of label free DNA hybridization on nm-sized gold interdigitated ultramicroelectrode arrays (Au-IDA) made in silicon technology. The array consists of eight different positions with an Au-IDA pair at each position arranged on the Si-based Biochip. Immobilization of capture probes onto the Au-IDA was accomplished by self-assembling of thiol-modified oligonucleotides. Target hybridization was indicated by a change in the magnitude of the time dependant potential relaxation curve in presence of electroactive Fe(CN)(6)(3-) in the phosphate buffer solution. While complementary DNA hybridization showed 50% increase in the relaxation potential, the non-complementary DNA showed a negligible change. A constant behaviour was noted for all positions. The dsDNA specific intercalating molecule, methylene blue, was found to be enhancing the discrimination effect. The changes in the relaxation potential curves were further corroborated following the ELISA like experiments using ExtraAvidine alkaline phosphatase labelling and redox recycling of para-aminophenol phosphate at IDAs. The coulostatic pulse technique was shown to be useful for identifying DNA sequences from brain tumour gene CK20, human herpes simplex virus, cytomegalovirus, Epstein-Barr virus and M13 phage. Compared to the hybridization of short chain ONTs (27 mers), the hybridization of long chain M13 phage DNA showed three times higher increase in the relaxation curves. The method is fast enough to monitor hybridization interactions in milli or microsecond time scales and is well suitable for miniaturization and integration compared to the common impedance techniques for developing capacitative DNA sensors.

Manipulation and extraction of genomic DNA from cell lysate by functionalized magnetic particles for lab on a chip applications.

A novel approach for extracting living cells' genomic DNA materials utilizing functionalized magnetic particles (MPs) is reported in this investigation. This strategy is amenable to handle bio-samples in a miniaturized environment and it offers a possibility to separate and purify DNA from other cell lysate mixtures "on-chip", which is known to be a bottle-neck step in an integrated micro-total-analysis-system (muTAS). "Species-specific" genomic DNA of interest is captured by the MPs based on the hybridization interaction between the biotinylated probes modified MPs and a complementary region of the targeted genome. The genome DNA anchored on the particles can be separated from the rest of cellular mixtures by a simple buffer washing upon the exertion of external magnetic force. Surface modifications of MPs and hybridization conditions affecting the genome capturing efficiency are investigated. Extraction of genomic DNA from E. coli is demonstrated in a silicon/glass-based micro-reactor patterned with a platinum heater and sensors. On-chip extraction and manipulation of genomic DNAs illustrated in this study is a step forward toward a total integrated bioanalytical microsystem for crude cells/sample analysis.

Towards a label-free optical porous silicon DNA sensor.

We report on the fabrication of an optical silicon-based label-free DNA sensor. n-Type crystalline silicon wafers have been electrochemically etched to form porous silicon layers and characterized in terms of porosity, pore distribution, surface composition and photoluminescence. Samples (0.25 cm(2)) have been cut and properly derivatized using trimethoxy-3-bromoacetamidopropylsilane in order to link single strand DNA (ss-DNA). Such a molecule is not commercially available and has been ad-hoc prepared by reacting hydrobromic acid and 3-aminopropyltrimethoxysilane in presence of 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide as coupling agent. Trimethoxy-3-bromoacetamidopropylsilane acts as a bridge anchored to the porous silicon surface through the silane group while immobilizing ss-DNA by means of the bromoacetamido moiety. We have found that derivatized samples exhibit a photoluminescence that is stable in time and is not modified after exposure to non-complementary DNA strand. On the other hand, a sensible enhancement of the light emission has been observed when the derivatized samples react with the complementary strand, showing that the specific ss-DNA/complementary DNA (c-DNA) interaction can be optically sensed without using further labeling steps. This strongly strengthens the possible role of silicon as a material for biosensors.

A monolithic silicon based integrated signal generation and detection system for monitoring DNA hybridisation.

The aim of this work was to develop an integrated solution to DNA hybridisation monitoring for diagnostics on a monolithic silicon platform. A fabrication process was developed incorporating a gold initiation electrode patterned directly onto a PIN photodiode detector. Patterned interdigitated type electrodes exhibited the smallest reduction in photodiode sensitivity, therefore these were chosen as the ECL initiator design. A novel DNA hybridisation assay was developed based on the displacement of a partially mismatched complementary strand by a perfectly matched labelled complementary strand. Pre-hybridised thiolated oligonucleotide and unlabelled 25% mismatched oligonucleotide were assembled on the gold initiation electrode. On addition of the labelled perfectly complementary oligonucleotide, the mismatched strands were displaced and a signal was generated. The sensitivity of the photodiode to light emitted at 620 nm, the ruthenium emission wavelength, was determined and subsequently, the diode current response to light generated by flow addition of ruthenium solution was found to be measurable to a concentration of 10 fM. Pre-hybridised duplex DNA, consisting of thiolated oligonucleotide and ruthenium labelled complementary oligonucleotide, was assembled on the gold initiation electrode. The difference between the current measured during flow of buffer and the ECL co-reactant TPA was three orders of magnitude, indicating that DNA assembled on the surface comprised sufficient ruthenium to generate a measurable signal. Finally, the displacement of unlabelled partial mismatch oligonucleotide from the sensor surface was monitored on addition of the ruthenium labelled perfectly complementary oligonucleotide in TPA flow and the measured photodiode current response was up to 50 times greater.

Genosensor on gold films with enzymatic electrochemical detection of a SARS virus sequence.

A hybridisation-based genosensor was designed on a 100 nm sputtered gold film. This material worked as an immobilisation and transduction surface. A 30-mer sequence that encodes a short lysine-rich region, unique to SARS (severe acute respiratory syndrome) virus, was chosen as target. A complementary strand (probe), labelled with a thiol group at the 3'-end, was immobilised on the film. After blocking the surface, hybridisation with the biotin-conjugated SARS strand (at the 3'-end) took place. Interaction with alkaline phosphatase-labelled streptavidin permits amplified indirect electrochemical detection. The analytical signal is constituted by an electrochemical process of indigo carmine, the soluble product of the enzymatic hydrolysis of 3-indoxyl phosphate. The use of a sensitive electrochemical technique such as square wave voltammetry allowed a detection limit of 6 pM to be obtained for this DNA sequence, lower than any other found in the bibliography. The parameters affecting the methodology were studied, with special attention being placed on selectivity. Specificity was clearly enhanced when interaction time and stringency (in the form of formamide percentage) were increased. With 1h of strand interaction and employing 50% of formamide in the hybridisation buffer, a 3-base mismatch strand was perfectly distinguished from the complementary.

Species differentiation by DNA-modified carbon electrodes using an ac impedimetric approach.

A simple and novel electrochemical biosensor based approach is described for differentiating between differing species of fish on the basis of DNA hybridisation events. Screen-printed carbon electrodes modified with a variety of polymers were used to immobilise commercially available DNA in a single-stranded form. AC impedimetric measurements were firstly carried out on these systems and then upon exposure to single-stranded DNA solutions. When the electrode and solution DNA were complementary, a large drop in impedance was measured; this did not occur for non-matching DNA exposures. DNA hybridisation sensors for closely related species of fish were in the first instance developed as a demonstration for this approach. Species of fish such as herrings and salmon could be differentiated by this method. This sensor format offers great promise for many DNA hybridisation applications and lends itself to mass fabrication due to the simplicity and inexpensiveness of the materials and methods used. The hybridisation results were confirmed by use of ellipsometry to measure the characteristics of similar films deposited on silicon substrates.

Amplicon secondary structure prevents target hybridization to oligonucleotide microarrays.

DNA microarrays that are used as end-point detectors for PCR assays are typically composed of short (15-25 mer) oligonucleotide probes bound to glass. When designing these detectors, we have frequently encountered situations where a probe would not hybridize to its complementary, terminally labeled PCR amplicon. To determine if failures could be explained by general phenomenon such as secondary structure, we designed a microarray to detect eight regions of the Escherichia coli 16S rDNA gene. We then amplified eight amplicons of different lengths using a biotin conjugated, antisense primer. Amplicons were then hybridized to the microarray and detected using a combination of signal amplification and fluorescence. In most cases, probe sequences complementary to the 5' region of the amplified products (sense orientation) did not hybridize to their respective amplicon. We tested for positional bias and showed that a biotin conjugated sense primer mirrored the same probe failures. Nick translated products, however, hybridized to all probes. Because nick translation generates many labeled fragments of random length, we concluded that this method disrupted secondary structure that otherwise prevented the amplicons from hybridizing to their respective probes. We also show that nick translation does not compromise detector sensitivity even when used with long PCR amplicons (ca. 1.5 kbp). Despite the increased cost of the nick translation, we concluded that this labeling strategy will reduce the time needed to design new assays as well as avoid possible false negatives during field applications. Alternative labeling strategies are also discussed.

Macroporous silicon electrical sensor for DNA hybridization detection.

Macroporous silicon (pore diameter 1-2 microm) was used in an electrical sensor for real time, label free detection of DNA hybridization. Electrical contacts were made exclusively on the back side of the substrate, which allowed complete exposure of the porous layer to DNA. Hybridization of a DNA probe with its complementary sequence produced a reduction in the impedance and a shift in the phase angle resulting from a change in dielectric constant inside the porous matrix and a modification of the depletion layer width in the crystalline silicon structure. The effect of the DNA charge on the response was corroborated using peptide nucleic acid (PNA), an uncharged analog of DNA. The sensitivity and selectivity of the device were characterized and the sensing properties of the porous layer alone were investigated using self-supporting macroporous silicon membranes.

Dynamic DNA hybridization on a chip using paramagnetic beads.

Dynamic DNA hybridization is presented as an approach to perform gene expression analysis. The method is advantageous because of its dynamic supplies of both DNA samples and probes. The approach was demonstrated on a microfluidic platform by incorporating paramagnetic beads as a transportable solid support. A glass chip was fabricated to allow simultaneous interrogation of eight DNA target samples by DNA probes. DNA targets were immobilized on beads via streptavidin-biotin conjugation or base pairing between oligonucleotide residues. The DNA/bead complex was introduced into the device in which hybridization took place with a complementary probe. The hybridized probe was then removed by heat denaturation to allow the DNA sample to be interrogated again by another probe with a different sequence of interest. A pneumatic pumping apparatus was constructed to transport DNA probes and other reagents into the microfluidic device while hydrostatic pumping was used for the introduction of paramagnetic beads with samples. After investigating three types of paramagnetic beads, we found Dynabeads Oligo(dT)25 best suited this application. Targets on the beads could be sequentially interrogated by probes for 12 times, and the hybridization signal was maintained within experimental variation. Demonstration of specific hybridization reactions in an array format was achieved using four synthesized DNA targets in duplicate and five probes in sequence, indicating the potential application of this approach to gene expression analysis.