A new broadband near-infrared emitting Mg2Al4Si5O18:Cr3+ phosphor for night-vision imaging.

Phosphor-converted light-emitting diodes (pc-LEDs) have important applications in security surveillance and food testing. However, developing new broadband near-infrared phosphors remains an important issue. Herein, the high-temperature solid-state reaction method was applied to synthesize a new type of Cr3+ doped Mg2Al4Si5O18 broadband NIR phosphor which matches a blue LED chip. It exhibits a broadband near-infrared (NIR) phosphor emission with a focus of 856 nm and a full width at half maximum >200 nm after excitation at 453 nm. The optimum concentration of Cr3+ was established to contain 2 mol%. At 398 K, the luminescence intensity is 45.2% of that at 298 K. The power output of NIR pc-LEDs fabricated by incorporating a 450 nm chip and the Mg2Al4Si5O18:0.02 Cr3+ phosphor is 19.69 mW at 300 mA current. Finally, the developed NIR pc-LED shows significant potential for use in night-vision imaging.

Photosynthetic efficiency, growth and secondary metabolism of common buckwheat (Fagopyrum esculentum Moench) in different controlled-environment production systems.

Light-emitting diodes (LEDs) and high-pressure sodium lamps (HPS) are among the most commonly used light sources for plant cultivation. The objective of this study was to evaluate the effect of two controlled-environment production systems differing in light sources on growth, photosynthetic activity, and secondary metabolism of common buckwheat. We hypothesized that LED light with the majority of red and blue waves would increase physiological and biochemical parameters compared to sunlight supplemented with HPS lamps. The experiment was performed in a phytotronic chamber (LEDs) and in a greenhouse (solar radiation supplemented with HPS lamps as a control). The effects were analyzed at the flowering phase with biometric measurements, leaf chlorophyll index, the kinetics of chlorophyll a fluorescence, content of soluble carbohydrates and phenolics in the leaves. Applied LED light decreased the biomass but stimulated the production of phenolics compared to control plants. In control plants, a positive correlation between flavonoid content and energy dissipation from photosystem II (DIo/CSm) was found, while in plants under LEDs total pool of phenolic content correlated with this parameter and the quantum yield of electron transport (φ Ro and ψ Ro) was lower than that of the control, probably affecting buckwheat biomass.

Dynamic white lighting to aid sleep and vision for persons living with dementia using off-the-shelf LED strips.

Alzheimer disease and related dementias affect 15-20% of elderly people, and 60-70% of these suffer from sleep disturbances. Studies suggest that lighting can improve sleep. The key challenge is how to deliver light effectively. We have designed a lighting system that adjusts spectrum and irradiance on a 24-hour timetable to provide spatially uniform, shadow-free white light with CRI>85 and up to 1000 Lux for day vision and amber light for night vision. To aid sleep, melanopic illuminance varies over 3 orders of magnitude to enable strong suppression of melatonin in the morning/early afternoon, moderate suppression in the evening, and no suppression at night.

Exploration of yellow-emitting phosphors for white LEDs from natural resources.

White light-emitting diodes (LEDs) are widely used in various lighting fields as a part of energy-efficient technology. However, some shortcomings of luminescent materials for white LEDs, such as complexity of synthesis, high cost, and harmful impact on the environment, limit their practical applications to a large extent. In this respect, the present work aims to study the ability of using Berberine (BBR) chloride extracted from Rhizoma coptidis and Phellodendron Chinese herbs as yellow phosphor for white LEDs. For this, white LEDs were successfully fabricated by applying 0.006 g of BBR chloride onto the blue LED chips (450 nm). The produced LEDs exhibited good luminescence properties at a voltage of 2.4 V along with eco-friendly characteristics and low cost. The Commission International de l'Eclairage chromaticity, the correlated color temperature, and the color rendering index were determined to be (${x} = {0.32}$, ${y} = {0.33}$), 5934 K, and 74, respectively. Therefore, BBR chloride is a suitable environmentally friendly and easily accessible yellow phosphor for white LEDs.

Effects of Supplementary Blue and UV-A LED Lights on Morphology and Phytochemicals of Brassicaceae Baby-Leaves.

Brassicaceae baby-leaves are good source of functional phytochemicals. To investigate how Chinese kale and pak-choi baby-leaves in response to different wavebands of blue (430 nm and 465 nm) and UV-A (380 nm and 400 nm) LED, the plant growth, glucosinolates, antioxidants, and minerals were determined. Both agronomy traits and phytochemical contents were significantly affected. Blue and UV-A light played a predominant role in increasing the plant biomass and morphology, as well as the contents of antioxidant compounds (vitamin C, vitamin E, phenolics, and individual flavonols), the antioxidant activity (DPPH and FRAP), and the total glucosinolates accumulation. In particular, four light wavebands significantly decreased the content of progoitrin, while 400 nm UV-A light and 430 nm blue light were efficient in elevating the contents of sinigrin and glucobrassicin in Chinese kale. Meanwhile, 400 nm UV-A light was able to increase the contents of glucoraphanin, sinigrin, and glucobrassicin in pak-choi. From the global view of heatmap, blue lights were more efficient in increasing the yield and phytochemical levels of two baby-leaves.

Quantifying risk factors associated with light-induced potato tuber greening in retail stores.

Light conditions in retail stores may contribute to potato greening. In this study, we aimed to develop a potato tuber greening risk rating model for retail stores based on light quality and intensity parameters. This was achieved by firstly exposing three potato varieties (Nicola, Maranca and Kennebec) to seven specific light wavelengths (370, 420, 450, 530, 630, 660 and 735 nm) to determine the tuber greening propensity. Detailed light quality and intensity measurements from 25 retail stores were then combined with the greening propensity data to develop a tuber greening risk rating model. Our study showed that maximum greening occurred under blue light (450 nm), while 53%, 65% and 75% less occurred under green (530 nm), red (660 nm) and orange (630 nm) light, respectively. Greening risk, which varied between stores, was found to be related to light intensity level, and partially explained potato stock loss in stores. Our results from this study suggested that other in-store management practices, including lighting duration, average potato turnover, and light protection during non-retail periods, likely influence tuber greening risk.

Use of reflective materials during phototherapy for newborn infants with unconjugated hyperbilirubinaemia.

BACKGROUND: Phototherapy is a well-established effective therapy for treating babies with significant neonatal jaundice. Studies have shown that increasing light intensity will increase its efficiency. A potentially inexpensive and easy way of increasing the intensity of light on the body of the infant may be to hang reflective materials from the sides of phototherapy units. OBJECTIVES: To assess the effects of reflective materials in combination with phototherapy compared with phototherapy alone for unconjugated hyperbilirubinaemia in neonates. SEARCH METHODS: We used the standard search strategy of Cochrane Neonatal to search the Cochrane Central Register of Controlled Trials (CENTRAL; 2019, Issue 11), in the Cochrane Library; Ovid MEDLINE(R) and Epub Ahead of Print, In-Process & Other Non-Indexed Citations, Daily and Versions(R); and the Cumulative Index of Nursing and Allied Health Literature (CINAHL), on 1 November 2019. We also searched clinical trials databases and the reference lists of retrieved articles for randomised controlled trials and quasi-randomised trials. SELECTION CRITERIA: We included randomised and quasi-randomised controlled trials if the participants, who were term or preterm infants, received phototherapy with curtains made of reflective materials of any type in the treatment arm, and if those in the comparison arm received similar phototherapy without curtains or other intensified phototherapy, such as a double bank of lights. DATA COLLECTION AND ANALYSIS: We used standard methodological procedures expected by Cochrane. We used the GRADE approach to assess the certainty of evidence. MAIN RESULTS: Of 15 studies identified, we included 12 (1288 babies) in the review - 11 comparing phototherapy with reflective materials and phototherapy alone, and one comparing a single phototherapy light bank with reflective materials with double phototherapy. All reflective materials consisted of curtains on three or four sides of the cot and were made of white plastic (five studies), white linen (two studies), or aluminium (three studies); materials were not specified in two studies. Only 11 studies (10 comparing reflective materials versus none and one comparing reflective curtains and a single bank of lights with a double (above and below) phototherapy unit) provided sufficient data to be included in the meta-analysis. Two excluded studies used the reflective materials in a way that did not meet our inclusion criteria, and we excluded one study because it compared four different phototherapy interventions not including reflective materials. The risk of bias of included studies was generally low, but all studies had high risk of performance bias due to lack of blinding of the intervention. Three studies (281 participants) reported a decline in serum bilirubin (SB) (µmol/L) at four to eight hours (mean difference (MD) -14.61, 95% confidence interval (CI) -19.80 to -9.42; I² = 57%; moderate-certainty evidence). Nine studies (893 participants) reported a decline in SB over 24 hours and showed a faster decline in SB in the intervention group, but heterogeneity (I² = 97%) was too substantial to permit a meaningful estimate of the actual effect size (very low-certainty evidence). Subgroup analysis by type of reflective material used did not explain the heterogeneity. Exchange transfusion was reported by two studies; both reported none in either group. Four studies (466 participants) reported the mean duration of phototherapy, and in each of these studies, it was reduced in the intervention group but there was substantial heterogeneity (I² = 88%), precluding meaningful meta-analysis of data. The only two studies that reported the mean duration of hospital stay in hours showed a meaningful reduction (MD -41.08, 95% CI -45.92 to -36.25; I² = 0; moderate-certainty evidence). No studies reported costs of the intervention, parental or medical staff satisfaction, breastfeeding outcomes, or neurodevelopmental follow-up. The only study that compared use of curtains with double phototherapy reported similar results for both groups. Studies that monitored adverse events did not report increased adverse events related to the use of curtains, including acute life-threatening events, but other rarer side effects could not be excluded. AUTHORS' CONCLUSIONS: Moderate-certainty evidence shows that the use of reflective curtains during phototherapy may result in greater decline in SB. Very low-certainty evidence suggests that the duration of phototherapy is reduced, and moderate-certainty evidence shows that the duration of hospital stay is also reduced. Available evidence does not show any increase in adverse events, but further studies are needed.

LEDs for photons, physiology and food.

Lighting based on light-emitting diodes (LEDs) not only is more energy efficient than traditional lighting, but also enables improved performance and control. The colour, intensity and distribution of light can now be controlled with unprecedented precision, enabling light to be used both as a signal for specific physiological responses in humans and plants, and as an efficient fuel for fresh food production. Here we show how a broad and improved understanding of the physiological responses to light will facilitate greater energy savings and provide health and productivity benefits that have not previously been associated with lighting.

Supplemental LED inter-lighting compensates for a shortage of light for plant growth and yield under the lack of sunshine.

Supplemental lighting can enhance yield when sunlight is limited, as in winter. As the effect of frequent cloudy or rainy days in other seasons on plant growth and yield remains unclear, we investigated the effect on tomato (Solanum lycopersicum) and compensation by supplemental LED inter-lighting. Plants were grown under 30% shade cloth on 0%, 40%, or 60% of days. Lower leaves were illuminated with red and blue LED inter-lighting modules from right after first anthesis, or not illuminated. Shading during 40% and 60% of days diminished daily light integral (DLI) by 26% and 40%, respectively, and reduced shoot dry weight by 22.0% and 23.3%, yield by 18.5% and 23.3%, and fruit soluble solids content by 12.3% and 9.3%. In contrast, supplemental inter-lighting improved the light distribution within plants and compensated DLI, and maintained similar yield and soluble solids content in both shade treatments as in the control. These results clearly show that supplemental LED inter-lighting could efficiently compensate for a shortage of light for plant growth, photosynthesis and thus yield under the lack of sunshine.

Trichogenic Photostimulation Using Monolithic Flexible Vertical AlGaInP Light-Emitting Diodes.

Alopecia is considered an aesthetic, psychological, and social issue among modern people. Although laser-induced skin stimulation is utilized for depilation treatment, such treatment has significant drawbacks of high energy consumption, huge equipment size, and limited usage in daily life. Here, we present a wearable photostimulator for hair-growth applications using high-performance flexible red vertical light-emitting diodes (f-VLEDs). Flexible microscale LEDs were effectively fabricated by a simple monolithic fabrication process, resulting in high light output (∼30 mW mm-2), low forward voltage (∼2.8 V), and excellent flexibility for wearable biostimulation. Finally, trichogenic stimulation of a hairless mouse was achieved using high-performance red f-VLEDs with high thermal stability, device uniformity, and mechanical durability.

Pretreatment with light-emitting diode therapy reduces ischemic brain injury in mice through endothelial nitric oxide synthase-dependent mechanisms.

Photostimulation with low-level light emitting diode therapy (LED-T) modulates neurological and psychological functions. The purpose of this study was to evaluate the effects of LED-T pretreatment on the mouse brain after ischemia/reperfusion and to investigate the underlying mechanisms. Ischemia/reperfusion brain injury was induced by middle cerebral artery occlusion. The mice received LED-T twice a day for 2 days prior to cerebral ischemia. After reperfusion, the LED-T group showed significantly smaller infarct and edema volumes, fewer behavioral deficits compared to injured mice that did not receive LED-T and significantly higher cerebral blood flow compared to the vehicle group. We observed lower levels of endothelial nitric oxide synthase (eNOS) phosphorylation in the injured mouse brains, but significantly higher eNOS phosphorylation in LED-T-pretreated mice. The enhanced phospho-eNOS was inhibited by LY294002, indicating that the effects of LED-T on the ischemic brain could be attributed to the upregulation of eNOS phosphorylation through the phosphoinositide 3-kinase (PI3K)/Akt pathway. Moreover, no reductions in infarct or edema volume were observed in LED-T-pretreated eNOS-deficient (eNOS-/-) mice. Collectively, we found that pretreatment with LED-T reduced the amount of ischemia-induced brain damage. Importantly, we revealed that these effects were mediated by the stimulation of eNOS phosphorylation via the PI3K/Akt pathway.

Investigation of the effect of UV-LED exposure conditions on the production of vitamin D in pig skin.

The dietary intake of vitamin D is currently below the recommended intake of 10-20µg vitamin D/day. Foods with increased content of vitamin D or new products with enhanced vitamin D are warranted. Light-emitting diodes (LEDs) are a potential new resource in food production lines. In the present study the exposure conditions with ultraviolet (UV) LEDs were systematically investigated in the wavelength range 280-340nm for achieving optimal vitamin D bio-fortification in pig skin. A wavelength of 296nm was found to be optimal for vitamin D3 production. The maximum dose of 20kJ/m(2) produced 3.5-4µg vitamin D3/cm(2) pig skin. Vitamin D3 produced was independent on the combination of time and intensity of the LED source. The increased UV exposure by UV-LEDs may be readily implemented in existing food production facilities, without major modifications to the process or processing equipment, for bio-fortifying food products containing pork skin.

High-intensity light-emitting diode vs fluorescent tubes for intensive phototherapy in neonates.

BACKGROUND: Special blue fluorescent tubes are recommended by the American Academy of Pediatrics (AAP) as the most effective light source for lowering serum bilirubin. A high-intensity light-emitting diode ('super LED') could render intensive phototherapy more effective than the above conventional methods. This study compared the efficacy and safety of a high-intensity light-emitting diode bed vs conventional intensive phototherapy with triple fluorescent tube units as a rescue treatment for severe unconjugated neonatal hyperbilirubinaemia. METHOD: This was a randomised, prospective trial. Two hundred jaundiced neonates ≥ 35 weeks gestation who met the criteria for intensive phototherapy as per AAP guidelines were randomly assigned to be treated either with triple fluorescent tube units (group 1, n = 100) or a super LED bed (group 2, n = 100). The outcome was the avoidance of exchange transfusion by successful control of hyperbilirubinaemia. RESULTS: Statistically significant higher success rates of intensive phototherapy were achieved among neonates treated with super LED (group 2) than in those treated conventionally (group 1) (87% vs 64%, P = 0.003). Significantly higher 'bilirubin decline' rates were reported in both haemolytic and non-haemolytic subgroups treated with the super LED bed compared with a similar sub-population in the conventionally treated group. Comparable numbers of neonates in both groups developed rebound jaundice (8% vs 10% of groups 1 and 2, respectively). Side-effects were mild in both groups, but higher rates of hyperthermia (12% vs 0%, P = 0.03), dehydration (8% vs 2%, P = 0.26) and skin rash (39% vs 1%, P = 0.002) were reported in the fluorescent tubes-treated group compared with the LED group. CONCLUSIONS: Super LED is a safe rescue treatment for severe neonatal hyperbilirubinaemia, and its implementation may reduce the need for exchange transfusion.

Sub-40 fs, 1060-nm Yb-fiber laser enhances penetration depth in nonlinear optical microscopy of human skin.

Advancing the practical utility of nonlinear optical microscopy requires continued improvement in imaging depth and contrast. We evaluated second-harmonic generation (SHG) and third-harmonic generation images from ex vivo human skin and showed that a sub-40 fs, 1060-nm Yb-fiber laser can enhance SHG penetration depth by up to 80% compared to a >100 fs, 800 nm Ti:sapphire source. These results demonstrate the potential of fiber-based laser systems to address a key performance limitation related to nonlinear optical microscopy (NLOM) technology while providing a low-barrier-to-access alternative to Ti:sapphire sources that could help accelerate the movement of NLOM into clinical practice.

Development of multi-colored LED system for therapeutic application.

BACKGROUND: The evaluation and control of lighting is crucial in physiological, biomedical, and industrial fields. Many kinds of lighting techniques based on LED have been developed due to its advantages. OBJECTIVE: The aim of this study is to develop the multi-colored LED system for healing purposes. METHODS: Light source with three-color chip LEDs was investigated to detect the dominant wavelength. RESULTS: The results show that the additive principle by three-color LEDs can be successfully applied to lighting system by generating a variety of colors. CONCLUSIONS: The results are expected to be useful in the field of light therapy and medicine. Applications of the developed light system are lighting therapies such as stimulating blood circulation and digestive processes, and controlling inflammation.

A practical review on photooxidation of crude oil: laboratory lamp setup and factors affecting it.

After an oil spill, crude oil in the marine environment is affected by a variety of processes collectively called weathering. Photooxidation induced by ultraviolet (UV) light from the sun is one of the most significant processes of long-term weathering that changes the chemical nature of oil. Experimental studies on photooxidation in the natural environment are generally not practicable due to the variability of factors that are more readily controlled in a laboratory. The emission spectra and irradiance of artificial lamps are critical factors for simulating sunlight, and the process of acceleration should be differentiated from simulation. We present a comprehensive review of the exposure conditions affecting in vitro photooxidation studies, including the types of lamps, their spectra and irradiance levels and maintenance conditions. The importance of xenon arc, metal halide along with mercury­xenon, high-pressure mercury lamps and other lamps with respect to their spectral characteristics is discussed and the selection guide is provided. A brief discussion on other factors affecting photooxidation rates and outcomes, such as photosensitisers, photodegraders, solvents and the synergistic effects of compounds is also given.

How synthetic biology will reconsider natural bioluminescence and its applications.

As our understanding of natural biological systems grows, so too does our ability to alter and rebuild them. Synthetic biology is the application of engineering principles to biology in order to design and construct novel biological systems for specific applications. Bioluminescent organisms offer a treasure trove of light-emitting enzymes that may have applications in many areas of bioengineering, from biosensors to lighting. A few select bioluminescent organisms have been well researched and the molecular and genetic basis of their luminescent abilities elucidated, with work underway to understand the basis of luminescence in many others. Synthetic biology will aim to package these light-emitting systems as self-contained biological modules, characterize their properties, and then optimize them for use in other chassis organisms. As this catalog of biological parts grows, synthetic biologists will be able to engineer complex biological systems with the ability to emit light. These may use luminescence for an array of disparate functions, from providing illumination to conveying information or allowing communication between organisms.

Enhanced light output power of thin film GaN-based high voltage light-emitting diodes.

The characteristics of high-voltage light-emitting diodes (HVLEDs) consisting of a 64-cell LED array were investigated by employing various LED structures. Two types of HVLED were examined: a standard HVLED with a single roughened indium tin oxide (ITO) surface grown on a sapphire substrate and a thin-film HVLED (TF-HVLED) with a roughened n-GaN and ITO double side transferred to a mirror/silicon substrate. At an injection current of 24 mA, the output powers of the HVLEDs fabricated using a sapphire substrate and those fabricated using a mirror/silicon substrate were 170 and 216 mW, respectively. Because the TF-HVLED exhibited improved thermal dissipation and light extraction, it produced a greater output power than the HVLED fabricated using the sapphire substrate did.

Surface plasmon-enhanced nanoporous GaN-based green light-emitting diodes with Al2O3 passivation layer.

A surface plasmon (SP)-enhanced nanoporous GaN-based green LED based on top-down processing technology has been successfully fabricated. This SP-enhanced LED consists of nanopores passing through the multiple quantum wells (MQWs) region, with Ag nanorod array filled in the nanopores for SP-MQWs coupling and thin Al(2)O(3) passivation layer for electrical protection. Compared with nanoporous LED without Ag nanorods, the electroluminescence (EL) peak intensity for the SP-enhanced LED was greatly enhanced by 380% and 220% at an injection current density of 1 and 20A/cm(2), respectively. Our results show that the increased EL intensity is mainly attributed to the improved internal quantum efficiency of LED due to the SP coupling between Ag nanorods and MQWs.

Characterization of 12CaO x 7Al2O3 doped indium tin oxide films for transparent cathode in top-emission organic light-emitting diodes.

12CaO x 7Al2O3, insulator (C12A7) doped indium tin oxide (ITO) (ITO:C12A7) films were fabricated using a radio frequency magnetron co-sputtering system with ITO and C12A7 targets. The qualitative and quantitative properties of ITO:C12A7 films, as a function of C12A7 concentration, were examined via X-ray photoemission spectroscopy and synchrotron X-ray scattering as well as by conducting atomic force microscopy. The work function of ITO:C12A7 (1.3%) films of approximately 2.8 eV obtained by high resolution photoemission spectroscopy measurements make them a reasonable cathode for top-emission organic light-emitting diodes.