ICP-MS based on-line monitoring of Pu-239 airborne concentration.

An online monitoring technology of Pu-239 aerosol based on aerosol direct introduction device, membrane desolvation nebuliser and ICP-MS was established for workplaces of reprocessing plants. Briefly, 0.8 l min-1 Pu-239 aerosol from the workplace was introduced into the aerosol direct introduction device where the air was replaced by Argon, and then the aerosol was introduced into the ICP-MS for measurement. To determine the activity of Pu-239 aerosol, 1.10E-3 Bq ml-1 Pu-242 standard solution generated by a membrane desolvation nebuliser was used. The introduction efficiency of the nebuliser was determined by sampling the aerosol generated from the nebuliser with Lead Standard Solution by glass fiber filter, which was (26.82 ± 3.33) %. The mass bias between Pu-239 and Pu-242 for the ICP-MS measurement was determined by Pu-239 and Pu-242 standard solutions generated by the nebuliser, and mass discrimination correction factor for Pu-239/Pu-242 was 0.972 ± 0.010. The limit of detection (LOD) and limit of quantification (LOQ) of this system were calculated according to the ISO 20 899:2018, which were 2.24E-05 Bq m-3 and 7.45E-05 Bq m-3 with 1 min measurement. The main interference which was from U-238 was determined by U-238 standard solution generated by the nebuliser, and the interferences of U-238 to 239 was (8.50 ± 1.05) E-05. According to the counts of U-238 from several workplaces of reprocessing plant where this system was tested, 239 counts rate from the interferences of U-238 of those workplaces were at the same level of the system background counts, which meant that the LOD above was suitable for those places.

INVESTIGATION OF RADIATION BACKGROUND IN THE MICRODISTRICTS OF KROPYVNYTSKYI USING DOSIMETER-RADIOMETER MKS-08-01 Gm «DKS-96¼ AND WIRELESS SENSORS. / DOSLIDZhENNIa RADIATsIY̆NOGO FONU V MIKRORAY̆ONAKh m. KROPYVNYTs'KOGO ZA DOPOMOGOIu DOZYMETRA-RADIOMETRA MKS-08-01 Gm «DKS-96¼ TA BEZDROTOVYKh DATChYKIV.

OBJECTIVE: Determine the radiation background in the Kropyvnytskyi microdistricts using the dosimeter-radiometer MKS-08-01 Gm «DKS-96¼ and a wireless sensor (dosimeter), analyze the measured values using the Student's t-test and create radiation background interactive map of Kropyvnytskyi microdistricts. MATERIALS AND METHODS: Measurement of Kropyvnytskyi radiation background was carried out in two ways: using the dosimeter-radiometer MKS-08-01 Gm «DKS-96¼ to measure the radiation background in the Kropyvnytskyi microdis- tricts (Zavadivka (sanitary zone and observation zone), Kovalivka, Velyka Balka, Lisoparkova, Raion 5/5, Popova, Miskyi sad); using a wireless sensor (dosimeter) with a monitoring system of the area radiation situation on the basis of Wi-Fi module with a microcontroller (Lisoparkova, Zavadivka (sanitary zone and observation zone), Raion 5/5). RESULTS AND CONCLUSIONS: Experiment results allowed us to conclude that in some microdistricts of Kropyvnytskyi increased level of radiation pollution. Evaluation of exposure for a human from technological reinforced naturally occurring radioactive sources, particularly from 238U and 222Rn is a key factor that determines the risk of cancerous pathologies in Kirovohrad region. We checked the effectiveness of our wireless sensor (dosimeter) for monitoring the radiation situation in the area. To analyze, interpret and report to the general public the results of our study, we created our own application for smartphones based on the Android operating system.

TYPE TESTING OF LiF:Mg,Cu,P (TLD-100H) WHOLE-BODY DOSEMETERS FOR THE ASSESSMENT OF Hp(10) AND Hp(0.07).

In this work, the initial results of the type testing of the LiF:Mg,Cu,P (TLD-100H) whole-body personal dosemeters are presented. An assessment of reproducibility, linearity of the response, the residual signal as a function of the dose, energy and angular dependence of the response was performed. In general, the dosemeters show good reproducibility for different dose values and a linear behaviour for a range between 0.1 and 300 mSv. The detection limits obtained are lower than 50 µSv. The system presents a good energy and angular response for different radiation qualities.

Wireless, battery-free, flexible, miniaturized dosimeters monitor exposure to solar radiation and to light for phototherapy.

Exposure to electromagnetic radiation can have a profound impact on human health. Ultraviolet (UV) radiation from the sun causes skin cancer. Blue light affects the body's circadian melatonin rhythm. At the same time, electromagnetic radiation in controlled quantities has beneficial use. UV light treats various inflammatory skin conditions, and blue light phototherapy is the standard of care for neonatal jaundice. Although quantitative measurements of exposure in these contexts are important, current systems have limited applicability outside of laboratories because of an unfavorable set of factors in bulk, weight, cost, and accuracy. We present optical metrology approaches, optoelectronic designs, and wireless modes of operation that serve as the basis for miniature, low-cost, and battery-free devices for precise dosimetry at multiple wavelengths. These platforms use a system on a chip with near-field communication functionality, a radio frequency antenna, photodiodes, supercapacitors, and a transistor to exploit a continuous accumulation mechanism for measurement. Experimental and computational studies of the individual components, the collective systems, and the performance parameters highlight the operating principles and design considerations. Evaluations on human participants monitored solar UV exposure during outdoor activities, captured instantaneous and cumulative exposure during blue light phototherapy in neonatal intensive care units, and tracked light illumination for seasonal affective disorder phototherapy. Versatile applications of this dosimetry platform provide means for consumers and medical providers to modulate light exposure across the electromagnetic spectrum in a way that can both reduce risks in the context of excessive exposure and optimize benefits in the context of phototherapy.

Dealing with crosstalk in electromagnetic field measurements of portable devices.

Portable devices measuring radiofrequency electromagnetic fields (RF-EMF) are affected by crosstalk: signals originating in one frequency band that are unintentionally registered in another. If this is not corrected, total exposure to RF-EMF is biased, particularly affecting closely spaced frequency bands such as GSM 1800 downlink (1,805-1,880 MHz), DECT (1,880-1,900 MHz), and UMTS uplink (1,920-1,980 MHz). This study presents an approach to detect and correct crosstalk in RF-EMF measurements, taking into account the real-life setting in which crosstalk is intermittently present, depending on the exact frequency of the signal. Personal measurements from 115 volunteers from Zurich canton, Switzerland were analyzed. Crosstalk-affected observations were identified by correlation analysis, and replaced by the median value of the unaffected observations, measured during the same activity. DECT is frequently a victim of crosstalk, and an average of 43% of observations was corrected, resulting in an average exposure reduction of 38%. GSM 1800 downlink and UMTS uplink were less often corrected (6.9% and 8.9%), resulting in minor reductions in exposure (7.1% and 0.92%). The contribution of DECT to total RF-EMF exposure is typically already low (3.2%), but is further reduced after correction (3.0%). Crosstalk corrections reduced the total exposure by 1.0% on average. Some individuals had a larger reduction of up to 16%. The code developed to make the corrections is provided for free as an R function which is easily applied to any time series of EMF measurements. Bioelectromagnetics. 39:529-538, 2018. © 2018 Wiley Periodicals, Inc.

Portable X-ray fluorescence system to measure Th and U concentrations.

This study reports the results obtained in the analysis of waste material samples generated by the industries of phosphate fertilizers, in particular, the use of specific filters in a portable X-ray fluorescence system, a simple equipment allowing the characterization, identification and quantification of low concentrations of Th and U (ppm). The industrial byproduct is classified as a Technologically-Enhanced, Naturally-Occurring Radioactive Material - TENORM, and therefore requires monitoring for its radio-toxic activity due to the presence of radioactive thorium and uranium families. From the results obtained, it is concluded that this technique is able to determine the contents of these elements to concentrations of tens of ppm in measurements of about 300 s, and a small sample amount (∼0.1 g).

Alpha Air Sample Counting Efficiency Versus Dust Loading: Evaluation of a Large Data Set.

Dust loading on air sample filters is known to cause a loss of efficiency for direct counting of alpha activity on the filters, but the amount of dust loading and the correction factor needed to account for attenuated alpha particles is difficult to assess. In this paper, correction factors are developed by statistical analysis of a large database of air sample results for a uranium and plutonium processing facility at the Savannah River Site. As is typically the case, dust-loading data is not directly available, but sample volume is found to be a reasonable proxy measure; the amount of dust loading is inferred by a combination of the derived correction factors and a Monte Carlo model. The technique compares the distribution of activity ratios [beta/(beta + alpha)] by volume and applies a range of correction factors on the raw alpha count rate. The best-fit results with this method are compared with MCNP modeling of activity uniformly deposited in the dust and analytical laboratory results of digested filters. A linear fit is proposed to evenly-deposited alpha activity collected on filters with dust loading over a range of about 2 mg cm to 1,000 mg cm.

Wearable slot antenna at 2.45 GHz for off-body radiation: Analysis of efficiency, frequency shift, and body absorption.

The interaction of body-worn antennas with the human body causes a significant decrease in antenna efficiency and a shift in resonant frequency. A resonant slot in a small conductive box placed on the body has been shown to reduce these effects. The specific absorption rate is less than international health standards for most wearable antennas due to small transmitter power. This paper reports the linear relationship between power absorbed by biological tissues at different locations on the body and radiation efficiency based on numerical modeling (r = 0.99). While the -10 dB bandwidth of the antenna remained constant and equal to 12.5%, the maximum frequency shift occurred when the antenna was close to the elbow (6.61%) and on the thigh (5.86%). The smallest change was found on the torso (4.21%). Participants with body-mass index (BMI) between 17 and 29 kg/m2 took part in experimental measurements, where the maximum frequency shift was 2.51%. Measurements showed better agreement with simulations on the upper arm. These experimental results demonstrate that the BMI for each individual had little effect on the performance of the antenna. Bioelectromagnetics. 39:25-34, 2018. © 2017 Wiley Periodicals, Inc.

Dose Quantification in UV Phototherapy.

Ultraviolet light has long been used to alleviate a number of skin conditions, and its efficacy is well known. However, over-exposure to ultraviolet radiation has a number of detrimental effects and thus it is vital to maintain a dose to skin within the therapeutic window. To maximise treatment gain whilst circumventing potential side-effects of over-exposure requires accurate determination of irradiance and skin-dose. This is complicated by the fact that ultraviolet radiation is essentially absorbed at the skin surface, which means that changing orientation of the patient and source can modulate dose received. In addition, irregular patient shapes mean dose must be carefully calibrated. This chapter focuses on methods of determination of dose, clinical protocols for quantifying radiation dose received and mathematical models for estimating these quantities.

SEISMIC PREDICTION USING UNATTACHED RADON DECAY PRODUCTS.

Long-term measurements of the 222Rn concentration, 222Rn decay product activity, particle size distribution, and unattached, and attached 222Rn decay products, were made at two locations using the 22 y radon decay product 210Pb as their tracer. The particle size sampler collects both short lived 222Rn decay products that ultimately decay to 210Pb on the filters, and also airborne 210Pb. The measurements were made outdoors, at a suburban home and at Fernald, OH, a former uranium processing facility, on top of one of the two 226Ra storage silos containing 150 TBq 226Ra. The size distributions showed the unattached fractions, i.e. particle diameter 2-4 nm, to be 1.5% at the home and 14% at the silos. The unattached fraction of 218Po can be shown to be an immediate measure of the 222Rn concentration. The data indicates detection of the pressure driven 222Rn flow at the silo and with the enhanced measurement capability of a filtered air source versus the usual 222Rn gas measurement. It is proposed that real time measurements of unattached 218Po may be used to identify rapidly changing 222Rn concentrations associated with pressure driven soil air flow associated with seismic activity.

Assessment of background gamma radiation levels using airborne gamma ray spectrometer data over uranium deposits, Cuddapah Basin, India - A comparative study of dose rates estimated by AGRS and PGRS.

The Atomic Minerals Directorate for Exploration and Research (AMD) has conducted high-resolution airborne gamma ray spectrometer (AGRS), magnetometer and time domain electromagnetic (TDEM) surveys for uranium exploration, along the northern margins of Cuddapah Basin. The survey area includes well known uranium deposits such as Lambapur-Peddagattu, Chitrial and Koppunuru. The AGRS data collected for uranium exploration is utilised for estimating the average absorbed rates in air due to radio-elemental (potassium in %, uranium and thorium in ppm) distribution over these known deposit areas. Further, portable gamma ray spectrometer (PGRS) was used to acquire data over two nearby locations one from Lambapur deposit, and the other from known anomalous zone and subsequently average gamma dose rates were estimated. Representative in-situ rock samples were also collected from these two areas and subjected to radio-elemental concentration analysis by gamma ray spectrometer (GRS) in the laboratory and then dose rates were estimated. Analyses of these three sets of results complement one another, thereby providing a comprehensive picture of the radiation environment over these deposits. The average absorbed area wise dose rate level is estimated to be 130 ± 47 nGy h-1 in Lambapur-Peddagattu, 186 ± 77 nGy h-1 in Chitrial and 63 ± 22 nGy h-1 in Koppunuru. The obtained average dose levels are found to be higher than the world average value of 54 nGy h-1. The gamma absorbed dose rates in nGy h-1 were converted to annual effective dose rates in mSv y-1 as proposed by the United Nations Scientific Committee on the Effect of Atomic Radiation (UNSCEAR). The annual average effective dose rates for the entire surveyed area is 0.12 mSv y-1, which is much lower than the recommended limit of 1 mSv y-1 by International Commission on Radiation protection (ICRP). It may be ascertained here that the present study establishes a reference data set (baseline) in these areas to assess any changes in gamma radiation levels due to mining and milling activities in future.

An HF exposure system for mice with improved efficiency.

An exposure system that addresses difficulties that arise for exposure of small animals at low frequencies with a high exposure level is presented. The system, intended to operate at 27 MHz, consists of two identical transverse electro-magnetic (TEM) cells for exposure and sham exposure of groups of 16 free-running mice housed in pairs within standard cages, capable of exposure over extended daily periods while being provided food and water. Inclusion of the exposure cell in a half-wavelength resonator has been developed as a new paradigm to enhance field strength for an increase of >50-fold in available specific absorption rate (SAR) levels compared to traditional TEM cell configurations. The system described allows both daily and weekly exposure schedules and supports blinded protocols with continuous wave (CW) and amplitude modulation (AM) signals with programmable modulation depths and frequencies. Electric field (E-field) homogeneity across the TEM cell along a vertical plane (orthogonal to the axis of the TEM line) was within 3.3%, and 3.1% along the horizontal plane. Accurate and comprehensive dosimetric assessments based on whole-body and organ-specific SAR essential for in vivo bioelectromagnetic experiments are presented, which takes into account various factors (e.g., mouse activities, close proximity, and field homogeneity). Average SAR levels are controllable in the range of 1 mW/kg to 2 W/kg, with expanded uncertainty (k = 2) of 1 dB and instantaneous variation (k = 1) of 4 dB.

On-body calibration and measurements using personal radiofrequency exposimeters in indoor diffuse and specular environments.

For the first time, response of personal exposimeters (PEMs) is studied under diffuse field exposure in indoor environments. To this aim, both numerical simulations, using finite-difference time-domain method, and calibration measurements were performed in the range of 880-5875 MHz covering 10 frequency bands in Belgium. Two PEMs were mounted on the body of a human male subject and calibrated on-body in an anechoic chamber (non-diffuse) and a reverberation chamber (RC) (diffuse fields). This was motivated by the fact that electromagnetic waves in indoor environments have both specular and diffuse components. Both calibrations show that PEMs underestimate actual incident electromagnetic fields. This can be compensated by using an on-body response. Moreover, it is shown that these responses are different in anechoic chamber and RC. Therefore, it is advised to use an on-body calibration in an RC in future indoor PEM measurements where diffuse fields are present. Using the response averaged over two PEMs reduced measurement uncertainty compared to single PEMs. Following the calibration, measurements in a realistic indoor environment were done for wireless fidelity (WiFi-5G) band. Measured power density values are maximally 8.9 mW/m(2) and 165.8 µW/m(2) on average. These satisfy reference levels issued by the International Commission on Non-Ionizing Radiation Protection in 1998. Power density values obtained by applying on-body calibration in RC are higher than values obtained from no body calibration (only PEMs) and on-body calibration in anechoic room, by factors of 7.55 and 2.21, respectively. Bioelectromagnetics. 37:298-309, 2016. © 2016 Wiley Periodicals, Inc.

Analysis of spectra from portable handheld gamma-ray spectrometry for terrain comparative assessment.

Geological characteristics can have impacts on societal development by, e.g., geotechnical issues and radiological hazard levels. Due to urban sprawl, there is an increasing need for detailed geological assessment. In this work are analysed data from portable handheld gamma-ray spectra (K, eU and eTh) obtained in granitic and Silurian metaclastic outcrops as well as in an profile, roughly N-S, on soil covered terrains transecting a mapped contact between these rock types (the profile's northern extremity is at locations mapped as granite). Estimations from gamma-ray spectra were studied by univariate and multivariate analyses. K, eU and eTh values were higher on granite in relation to Silurian metaclastic rocks. The northern extremity of the profile showed clearly higher contents of eTh and this contrast was supported by univariate statistical tools (normality plot and Wilk-Shapiro test; boxplots). A ternary plot with the contribution of the elements to gamma-ray absorbed dose showed the separation of granite from Silurian metaclastic rocks with the former being nearer the eTh vertex. The points in the northern extremity of the profile are nearer the eTh vertex than the other points on the profile. These visual suggestions were supported by hierarchical cluster analysis, which was able to differentiate between granite and metaclastic outcrops and separate portions of the profile located on different terrains. Portable gamma-ray spectrometry showed, hence, the potential to distinguish granite and metaclastic terrains at a scale useful for engineering works. These results can also be useful for a first comparative zoning of radiological hazards (which are higher for granite).

RADIATION DOSE MEASUREMENTS FOR HIGH-INTENSITY LASER INTERACTIONS WITH SOLID TARGETS AT SLAC.

A systematic study of photon and neutron radiation doses generated in high-intensity laser-solid interactions is underway at SLAC National Accelerator Laboratory. These laser-solid experiments are being performed using a 25 TW (up to 1 J in 40 fs) femtosecond pulsed Ti:sapphire laser at the Linac Coherent Light Source's (LCLS) Matter in Extreme Conditions (MEC) facility. Radiation measurements were performed with passive and active detectors deployed at various locations inside and outside the target chamber. Results from radiation dose measurements for laser-solid experiments at SLAC MEC in 2014 with peak intensity between 1018 and 7.1 × 1019 W cm-2 are presented.

FADING EFFECT OF LiF:Mg,Ti AND LiF:Mg,Cu,P Ext-Rad AND WHOLE-BODY DETECTORS.

Thermoluminescence dosemeters are widely used in individual and environmental monitoring. The aim of this work was to compare the thermal stability of dosemeters of the Ext-Rad and whole-body card types with LiF:Mg,Ti and LiF:Mg,Cu,P detectors stored at different temperatures and periods. The dosemeters were stored at 0°C, room temperature and 40°C for periods that lasted 8, 30, 45, 90 and 120 d. In general, TLD-100H detectors present higher TL signal stability than TLD-100 detectors. The intensity of the signal remained constant for both materials for storage periods at 0°C. At RT the same results was observed for TLD-100H. For TLD-100 detectors, a maximum variation of 22 % was registered for the longest period. At 40°C the TL signal decreased with storage time for both detectors. The TL signal of TLD-100H detectors presented maximum variations of 12 % whereas for TLD-100 detectors, larger variations of 25 % were observed.

PROPERTIES OF THE BEOSL DOSIMETRY SYSTEM IN THE FRAMEWORK OF A LARGE-SCALE PERSONAL MONITORING SERVICE.

The Individual Monitoring Service of the Helmholtz Zentrum München is currently using the BeOSL dosimetry system for monitoring ∼15 000 persons per month. This dosimetry system has a modular structure and represents a complete new concept on handling dosemeters in a large-scale dosimetry service. It is based on optically stimulated luminescence dosemeters made of beryllium oxide. The dosimetric and operational properties of the system are shown and discussed.

RELATIVE DISSOLUTION RATES OF RADIOACTIVE MATERIALS USED AT AWE.

A simple in vitro dissolution test was used to provide a semi-quantitative comparison of the relative dissolution rates of samples of radioactive materials used at Atomic Weapons Establishment in a lung fluid surrogate (Ringer's solution). A wide range of dissolution rates were observed for aged legacy actinides, freshly produced actinide alloys and actinides from waste management operations.

ENHANCED RADIOACTIVE CONTENT OF 'BALANCE' BRACELETS.

During a routine whole body counting measurement of a worker at the Nuclear Research Center Negev, abnormal activities of (232)Th and (238)U were measured. After a thorough investigation, it was found that the radioactivity was due to a rubber bracelet ('balance bracelet') worn by the worker during the measurement. The bracelet was counted directly by an high pure germanium gamma spectrometry system, and the specific activities determined were 10.80 ± 1.37 Bq g(-1) for (232)Th and 5.68 ± 0.88 Bq g(-1) for natural uranium. These values are obviously high compared with normally occurring radioactive material (NORM) average values. The dose rate to the wrist surface was estimated to be ∼3.9 µGy h(-1) and ∼34 mGy for a whole year. The dose rate at the centre of the wrist was estimated to be ∼2.4 µGy h(-1) and ∼21 mGy for a whole year. The present findings stresses a more general issue, as synthetic rubber and silicone products are common and widely used, but their radioactivity content is mostly uncontrolled, thus causing unjustified exposure due to enhanced NORM radioactivity levels.