Identifying patterns and sources of anthropogenic trace metals in the Argentine Central Andes by using snow samples and an atmospheric dispersion model.

This study presents the first local measurements of metals in snow from the Argentine Central Andes. Cu, Pb and Zn were selected as specific tracers of anthropogenic local emission sources in the study area. Snow samples were collected during winter (2014, 2015 and 2016) at two sites with different characteristics: Punta de Vacas and Vallecitos. The samples were analyzed by ICP-MS, and the average concentrations found were 1.4 µg L-1 (Cu), 2.2 µg L-1 (Pb) and 14.2 µg L-1 (Zn) in the snow samples from Vallecitos, and 5.3 µg L-1 (Cu), 2.6 µg L-1 (Pb) and 24.0 µg L-1 (Zn) in the snow samples from Punta de Vacas. These data and the snowfall amount in each sampling site were statistically analyzed. Results suggested that the levels of metals in the snow are influenced not only by the atmospheric concentrations, but also by the amount of precipitated snow. Additionally, an atmospheric dispersion model, CALPUFF, was applied in the study area to determine the origin of the studied metals and to understand the spatial distribution pattern of the concentrations found. Results showed that the metal atmospheric loads in the study area originated from local sources, especially vehicular traffic and mining. This work represents an important contribution to the knowledge and preservation of the local Andean cryosphere, and it could be used as an input to develop protection policies in the area through the combination of different and complementary tools for the evaluation of air quality.

Concomitant occurrence of anthropogenic air pollutants, mineral dust and fungal spores during long-distance transport of ragweed pollen.

Large-scale synoptic conditions are able to transport considerable amounts of airborne particles over entire continents by creating substantial air mass movement. This phenomenon is observed in Europe in relation to highly allergenic ragweed (Ambrosia L.) pollen grains that are transported from populations in Central Europe (mainly the Pannonian Plain and Balkans) to the North. The path taken by atmospheric ragweed pollen often passes through the highly industrialised mining region of Silesia in Southern Poland, considered to be one of the most polluted areas in the EU. It is hypothesized that chemical air pollutants released over Silesia could become mixed with biological material and be transported to less polluted regions further North. We analysed levels of air pollution during episodes of long-distance transport (LDT) of ragweed pollen to Poland. Results show that, concomitantly with pollen, the concentration of air pollutants with potential health-risk, i.e. SO2, and PM10, have also significantly increased (by 104% and 37%, respectively) in the receptor area (Western Poland). Chemical transport modelling (EMEP) and air mass back-trajectory analysis (HYSPLIT) showed that potential sources of PM10 include Silesia, as well as mineral dust from the Ukrainian steppe and the Sahara Desert. In addition, atmospheric concentrations of other allergenic biological particles, i.e. Alternaria Nees ex Fr. spores, also increased markedly (by 115%) during LDT episodes. We suggest that the LDT episodes of ragweed pollen over Europe are not a "one-component" phenomenon, but are often related to elevated levels of chemical air pollutants and other biotic and abiotic components (fungal spores and desert dust).

Enhanced phosphorus removal in intermittently aerated constructed wetlands filled with various construction wastes.

Phosphorus (P) loss by various pathways in constructed wetlands (CWs) is often variable. The effects of intermittent aeration and different construction waste substrates (gravel, red brick, fly-ash brick) on P processing using six batch-operated vertical flow constructed wetlands (VFCWs) were studied for decentralized domestic wastewater treatment. Average removal of total phosphorus (TP) in three aerated CWs was markedly higher (21.06, 24.83, and 27.02 mg m-2 day-1, respectively) than non-aerated CWs (10.64, 18.16, and 25.09 mg m-2 day-1, respectively). Fly-ash brick offered superior TP removal efficiency in both aerated and non-aerated batch-operated VFCWs, suggesting its promising application for P removal in CWs. Aeration greatly promoted plant growth and thusly increased plant uptake of P by 0.57-1.45 times. Substance storage was still the main P sink accounting for 23.92-59.47% of TP removal. Other process including microbial uptake was revealed to be a very important P removal pathway (accounting for 14.86-34.84%). The contribution of microbial uptake was also indicated by microbial analysis. Long-term results suggested that the contribution of microbial P uptake could be always ignored and underestimated in most CWs. A combination of intermittent aeration and suitable substrates is effective to intensify P transformation in CWs.

Airborne Quercus pollen in SW Spain: Identifying favourable conditions for atmospheric transport and potential source areas.

The pollen grains of Quercus spp. (oak trees) are allergenic. This study investigates airborne Quercus pollen in SW Spain with the aim identifying favourable conditions for atmospheric transport and potential sources areas. Two types of Quercus distribution maps were produced. Airborne Quercus pollen concentrations were measured at three sites located in the Extremadura region (SW Spain) for 3 consecutive years. The seasonal occurrence of Quercus pollen in the air was investigated, as well as days with pollen concentrations ≥80Pm(-3). The distance that Quercus pollen can be transported in appreciable numbers was calculated using clusters of back trajectories representing the air mass movement above the source areas (oak woodlands), and by using a state-of-the-art dispersion model. The two main potential sources of Quercus airborne pollen captured in SW Spain are Q. ilex subsp. ballota and Q. suber. The minimum distances between aerobiological stations and Quercus woodlands have been estimated as: 40km (Plasencia), 66km (Don Benito), 62km (Zafra) from the context of this study. Daily mean Quercus pollen concentration can exceed 1,700Pm(-3), levels reached not less than 24 days in a single year. High Quercus pollen concentration were mostly associated with moderate wind speed events (6-10ms(-1)), whereas that a high wind speed (16-20ms(-1)) seems to be associated with low concentrations.

Investigation of hybrid plasma-catalytic removal of acetone over CuO/γ-Al2O3 catalysts using response surface method.

In this work, plasma-catalytic removal of low concentrations of acetone over CuO/γ-Al2O3 catalysts was carried out in a cylindrical dielectric barrier discharge (DBD) reactor. The combination of plasma and the CuO/γ-Al2O3 catalysts significantly enhanced the removal efficiency of acetone compared to the plasma process using the pure γ-Al2O3 support, with the 5.0 wt% CuO/γ-Al2O3 catalyst exhibiting the best acetone removal efficiency of 67.9%. Catalyst characterization was carried out to understand the effect the catalyst properties had on the activity of the CuO/γ-Al2O3 catalysts in the plasma-catalytic reaction. The results indicated that the formation of surface oxygen species on the surface of the catalysts was crucial for the oxidation of acetone in the plasma-catalytic reaction. The effects that various operating parameters (discharge power, flow rate and initial concentration of acetone) and the interactions between these parameters had on the performance of the plasma-catalytic removal of acetone over the 5.0 wt% CuO/γ-Al2O3 catalyst were investigated using central composite design (CCD). The significance of the independent variables and their interactions were evaluated by means of the Analysis of Variance (ANOVA). The results showed that the gas flow rate was the most significant factor affecting the removal efficiency of acetone, whilst the initial concentration of acetone played the most important role in determining the energy efficiency of the plasma-catalytic process.

The long distance transport of airborne Ambrosia pollen to the UK and the Netherlands from Central and south Europe.

The invasive alien species Ambrosia artemisiifolia (common or short ragweed) is increasing its range in Europe. In the UK and the Netherlands, airborne concentrations of Ambrosia pollen are usually low. However, more than 30 Ambrosia pollen grains per cubic metre of air (above the level capable to trigger allergic symptoms) were recorded in Leicester (UK) and Leiden (NL) on 4 and 5 September 2014. The aims of this study were to determine whether the highly allergenic Ambrosia pollen recorded during the episode could be the result of long distance transport, to identify the potential sources of these pollen grains and to describe the conditions that facilitated this possible long distance transport. Airborne Ambrosia pollen data were collected at 10 sites in Europe. Back trajectory and atmospheric dispersion calculations were performed using HYSPLIT_4. Back trajectories calculated at Leicester and Leiden show that higher altitude air masses (1500 m) originated from source areas on the Pannonian Plain and Ukraine. During the episode, air masses veered to the west and passed over the Rhône Valley. Dispersion calculations showed that the atmospheric conditions were suitable for Ambrosia pollen released from the Pannonian Plain and the Rhône Valley to reach the higher levels and enter the airstream moving to northwest Europe where they were deposited at ground level and recorded by monitoring sites. The study indicates that the Ambrosia pollen grains recorded during the episode in Leicester and Leiden were probably not produced by local sources but transported long distances from potential source regions in east Europe, i.e. the Pannonian Plain and Ukraine, as well as the Rhône Valley in France.

Mesoscale atmospheric transport of ragweed pollen allergens from infected to uninfected areas.

Allergenic ragweed (Ambrosia spp.) pollen grains, after being released from anthers, can be dispersed by air masses far from their source. However, the action of air temperature, humidity and solar radiation on pollen grains in the atmosphere could impact on the ability of long distance transported (LDT) pollen to maintain allergenic potency. Here, we report that the major allergen of Ambrosia artemisiifolia pollen (Amb a 1) collected in ambient air during episodes of LDT still have immunoreactive properties. The amount of Amb a 1 found in LDT ragweed pollen grains was not constant and varied between episodes. In addition to allergens in pollen sized particles, we detected reactive Amb a 1 in subpollen sized respirable particles. These findings suggest that ragweed pollen grains have the potential to cause allergic reactions, not only in the heavily infested areas but, due to LDT episodes, also in the regions unaffected by ragweed populations.

Risk of exposure to airborne Ambrosia pollen from local and distant sources in Europe - an example from Denmark.

BACKGROUND: Ambrosia artemisiifolia L. is a noxious invasive alien species in Europe. It is an important aeroallergen and millions of people are exposed to its pollen. OBJECTIVE: The main aim of this study is to show that atmospheric concentrations of Ambrosia pollen recorded in Denmark can be derived from local or more distant sources. METHODS: This was achieved by using a combination of pollen measurements, air mass trajectory calculations using the HYPLIT model and mapping all known Ambrosia locations in Denmark and relating them to land cover types. RESULTS: The annual pollen index recorded in Copenhagen during a 15-year period varied from a few pollen grains to more than 100. Since 2005, small quantities of Ambrosia pollen has been observed in the air every year. We have demonstrated, through a combination of Lagrangian back-trajectory calculations and atmospheric pollen measurements, that pollen arrived in Denmark via long-distance transport from centres of Ambrosia infection, such as the Pannonian Plain and Ukraine. Combining observations with results from a local scale dispersion model show that it is possible that Ambrosia pollen could be derived from local sources identified within Denmark. CONCLUSIONS: The high allergenic capacity of Ambrosia pollen means that only small amounts of pollen are relevant for allergy sufferers, and just a few plants will be sufficient to produce enough pollen to affect pollen allergy sufferers within a short distance from the source. It is necessary to adopt control measures to restrict Ambrosia numbers. Recommendations for the removal of all Ambrosia plants can effectively reduce the amount of local pollen, as long as the population of Ambrosia plants is small.

Fumio Matsumura--accomplishments at the University of California, Davis, and in the Sierra Nevada Mountains.

Fumio Matsumura joined the University of California, Davis, faculty in 1987 where he served as founding director of the Center for Environmental Health Sciences, associate director of the U.C. Toxic Substances Research and Teaching Program, and chair of the Department of Environmental Toxicology. He was an active affiliate with the NIEHS-funded Superfund Basic Research Program and the NIH Comprehensive Cancer Center. He was in many instances a primary driver or otherwise involved in most activities related to environmental toxicology at Davis, including the education of students in environmental biochemistry and ecotoxicology. A significant part of his broad research program was focused on the long range transport of chemicals such as toxaphene, PCBs and related contaminants used or released in California to the Sierra Nevada mountains, downwind of the urban and agricultural regions of the state. He hypothesized that these chemical residues adversely affected fish and wildlife, and particularly the declining populations of amphibians in Sierra Nevada streams and lakes. Fumio and his students and colleagues found residues of toxaphene and PCBs at higher elevations, an apparent result of atmospheric drift and deposition in the mountains. Fumio and his wife Teruko had personal interests in, and a love of the mountains, as avid skiers, hikers, and outdoor enthusiasts.

A comparison of the closed-face cassette at different orientations while measuring total particles.

The current method for sampling aerosols using the 37-mm closed-face cassette (CFC) sampler is based on the orientation of the cassette at ∼45° from horizontal. There is some concern as to whether this method is appropriate and may be underestimating exposures. An alternative orientation at ∼0° (horizontal) has been discussed. This research compared the CFC's orientation at 45° from horizontal to the proposed orientation at horizontal, 0° in a controlled laboratory setting. The particles used in this study were fused alumina oxide in four sizes, approximately 9.5 µm, 12.8 µm, 18 µm, and 44.3 µm in aerodynamic diameter. For each test, one aerosol was dispersed in a wind tunnel operating at 0.2 m/s with samplers mounted in the breathing zone of a rotating mannequin. A sampling event consisted of four pairs of samplers, placed side by side (one pair at 45° and another at 0° cassette orientation), and exposed for a period of 45 minutes. A total of 12 sampling events, 3 sample events per particle size, were conducted with a total of 94 samples collected. Mass concentration measurements were compared to assess the relationship between the sampler orientations of the cassettes. In addition, the relationship between the mass collected on the cassette filter and on the interior walls of the cassette was also assessed. The results indicated that there was no significant difference between the measured concentrations based on the orientation of the CFCs. The amount of mass collected on the interior walls of the cassettes was relatively low (<5%) compared to expected (up to 100%) wall losses for both orientations.

Health risk assessments for alumina refineries.

OBJECTIVE: To describe contemporary air dispersion modeling and health risk assessment methodologies applied to alumina refineries and to summarize recent results. METHODS: Air dispersion models using emission source and meteorological data have been used to assess ground-level concentrations (GLCs) of refinery emissions. Short-term (1-hour and 24-hour average) GLCs and annual average GLCs have been used to assess acute health, chronic health, and incremental carcinogenic risks. RESULTS: The acute hazard index can exceed 1 close to refineries, but it is typically less than 1 at neighboring residential locations. The chronic hazard index is typically substantially less than 1. The incremental carcinogenic risk is typically less than 10(-6). CONCLUSIONS: The risks of acute health effects are adequately controlled, and the risks of chronic health effects and incremental carcinogenic risks are negligible around referenced alumina refineries.

Improvement in the accuracy of back trajectories using WRF to identify pollen sources in southern Iberian Peninsula.

Airborne pollen transport at micro-, meso-gamma and meso-beta scales must be studied by atmospheric models, having special relevance in complex terrain. In these cases, the accuracy of these models is mainly determined by the spatial resolution of the underlying meteorological dataset. This work examines how meteorological datasets determine the results obtained from atmospheric transport models used to describe pollen transport in the atmosphere. We investigate the effect of the spatial resolution when computing backward trajectories with the HYSPLIT model. We have used meteorological datasets from the WRF model with 27, 9 and 3 km resolutions and from the GDAS files with 1° resolution. This work allows characterizing atmospheric transport of Olea pollen in a region with complex flows. The results show that the complex terrain affects the trajectories and this effect varies with the different meteorological datasets. Overall, the change from GDAS to WRF-ARW inputs improves the analyses with the HYSPLIT model, thereby increasing the understanding the pollen episode. The results indicate that a spatial resolution of at least 9 km is needed to simulate atmospheric flows that are considerable affected by the relief of the landscape. The results suggest that the appropriate meteorological files should be considered when atmospheric models are used to characterize the atmospheric transport of pollen on micro-, meso-gamma and meso-beta scales. Furthermore, at these scales, the results are believed to be generally applicable for related areas such as the description of atmospheric transport of radionuclides or in the definition of nuclear-radioactivity emergency preparedness.

Assessment of volatile organic compound removal by indoor plants--a novel experimental setup.

Indoor plants can remove volatile organic compounds (VOCs) from the air. The majority of knowledge comes from laboratory studies where results cannot directly be transferred to real-life settings. The aim of this study was to develop an experimental test system to assess VOC removal by indoor plants which allows for an improved real-life simulation. Parameters such as relative humidity, air exchange rate and VOC concentration are controlled and can be varied to simulate different real-life settings. For example, toluene diffusion through a needle gave concentrations in the range of 0.10-2.35 µg/L with deviations from theoretical values of 3.2-10.5%. Overall, the system proved to be functional for the assessment of VOC removal by indoor plants with Hedera helix reaching a toluene removal rate of up to 66.5 µg/m(2)/h. The mode of toluene exposure (semi-dynamic or dynamic) had a significant influence on the removal rate obtained by H. helix.

[Optimization of one-step pelletization technology of Jiuwei Xifeng granules by response surface methodology].

Using the qualified rates of particles as the evaluation indexes, the impact tactors of one-step pelletization technology of Jiuwei Xifeng granules were selected from six factors by the Plackett-Burman experimental design and the levels of non-significant factors were identified. According to the Plackett-Burman experimental design, choosing the qualified rates of particles and angle of repose as the evaluation indexes, three levels of the three factors were selected by Box-Behnken of central composite design to optimize the experimental. The best conditions were as follows: the fluid extract was sprayed with frequency of 29 r . min-1, inlet air temperature was 90 °C, the frequency of fan was 34 Hz. Under the response surface methodology optimized scheme, the average experimental results are similar to the predicted values, and surface methodology could be used in the optimization of one-step pelletization for Chinese materia medica.

Optimization of one-step pelletization technology of Jiuwei Xifeng granules by response surface methodology / 中国中药杂志

Using the qualified rates of particles as the evaluation indexes, the impact tactors of one-step pelletization technology of Jiuwei Xifeng granules were selected from six factors by the Plackett-Burman experimental design and the levels of non-significant factors were identified. According to the Plackett-Burman experimental design, choosing the qualified rates of particles and angle of repose as the evaluation indexes, three levels of the three factors were selected by Box-Behnken of central composite design to optimize the experimental. The best conditions were as follows: the fluid extract was sprayed with frequency of 29 r . min-1, inlet air temperature was 90 °C, the frequency of fan was 34 Hz. Under the response surface methodology optimized scheme, the average experimental results are similar to the predicted values, and surface methodology could be used in the optimization of one-step pelletization for Chinese materia medica.

The cavity structure effect in medicine: the physical aspect.

BACKGROUND: In 1893 the German scientist Oskar Korschelt was granted a patent for using cavity structures (CS) for therapeutic purposes. In the end of the 20th century in Russia Victor Grebennikov also studied possibilities of using CS in curing various diseases. Korschelt used artificial CSs made of copper chains or plates. Grebennikov used mainly natural CS, e.g., empty bee combs. The main features of the CS effect are: the therapeutic efficacy of a CS depends on its orientation with respect to the biological object and on the material the CS is made of. It does not depend on the presence of acoustic or electromagnetic screens. The CS influence on the target biological object may not cease after removal of the CS, i.e. there is an after-effect. METHODS: It is shown in the paper that it is possible to explain the effects of CSs on biological objects under the assumption that the physical vacuum has the properties of superfluid (3)He-B. RESULTS: The effects may be due to spin supercurrents being present in CSs. CONCLUSION: CSs differ from bodies of other form in that the cavity is 'filled' with spin supercurrents. The properties of the supercurrents are like those of the spin supercurrents between spin structures in superfluid (3)He-B.

Tracking hazardous air pollutants from a refinery fire by applying on-line and off-line air monitoring and back trajectory modeling.

The air monitors used by most regulatory authorities are designed to track the daily emissions of conventional pollutants and are not well suited for measuring hazardous air pollutants that are released from accidents such as refinery fires. By applying a wide variety of air-monitoring systems, including on-line Fourier transform infrared spectroscopy, gas chromatography with a flame ionization detector, and off-line gas chromatography-mass spectrometry for measuring hazardous air pollutants during and after a fire at a petrochemical complex in central Taiwan on May 12, 2011, we were able to detect significantly higher levels of combustion-related gaseous and particulate pollutants, refinery-related hydrocarbons, and chlorinated hydrocarbons, such as 1,2-dichloroethane, vinyl chloride monomer, and dichloromethane, inside the complex and 10 km downwind from the fire than those measured during the normal operation periods. Both back trajectories and dispersion models further confirmed that high levels of hazardous air pollutants in the neighboring communities were carried by air mass flown from the 22 plants that were shut down by the fire. This study demonstrates that hazardous air pollutants from industrial accidents can successfully be identified and traced back to their emission sources by applying a timely and comprehensive air-monitoring campaign and back trajectory air flow models.

Effect of flow characteristics on ultrafine particle emissions from range hoods.

In order to understand the physical mechanisms of the production of nanometer-sized particulate generated from cooking oils, the ventilation of kitchen hoods was studied by determining the particle concentration, particle size distribution, particle dimensions, and hood's flow characteristics under several cooking scenarios. This research varied the temperature of the frying operation on one cooking operation, with three kinds of commercial cooking oils including soybean oil, olive oil, and sunflower oil. The variations of particle concentration and size distributions with the elevated cooking oil temperatures were presented. The particle concentration increases as a function of temperature. For oil temperatures ranging between 180°C and 210°C, a 5°C increase in temperature increased the number concentration of ultrafine particles by 20-50%. The maximum concentration of ultrafine particles was found to be approximately 6 × 10(6) particles per cm(3) at 260°C. Flow visualization techniques and particle distribution measurement were performed for two types of hood designs, a wall-mounted range hood and an island hood, at a suction flow rate of 15 m(3) min(-1). The flow visualization results showed that different configurations of kitchen hoods induce different aerodynamic characteristics. By comparing the results of flow visualizations and nanoparticle measurements, it was found that the areas with large-scale turbulent vortices are more prone to dispersion of ultrafine particle leakage because of the complex interaction between the shear layers and the suction movement that results from turbulent dispersion. We conclude that the evolution of ultrafine particle concentration fluctuations is strongly affected by the location of the hood, which can alter the aerodynamic features. We suggest that there is a correlation between flow characteristics and amount of contaminant leakage. This provides a comprehensive strategy to evaluate the effectiveness of kitchen hoods in capturing cooking oil fumes, which is based on an assessment of the entire hood face exposure instead of on breathing-zone sampling alone.

A numerical model of birch pollen emission and dispersion in the atmosphere. Description of the emission module.

A birch pollen emission model is described and its main features are discussed. The development of the model is based on a double-threshold temperature sum model that describes the propagation of the flowering season and naturally links to the thermal time models to predict the onset and duration of flowering. For the flowering season, the emission model considers ambient humidity and precipitation rate, both of which suppress the pollen release, as well as wind speed and turbulence intensity, which promote it. These dependencies are qualitatively evaluated using the aerobiological observations. Reflecting the probabilistic character of the flowering of an individual tree in a population, the model introduces relaxation functions at the start and end of the season. The physical basis of the suggested birch pollen emission model is compared with another comprehensive emission module reported in literature. The emission model has been implemented in the SILAM dispersion modelling system, the results of which are evaluated in a companion paper.

Ragweed pollen observed in Turkey: detection of sources using back trajectory models.

This paper discusses the pollen season and the source apportionment of ragweed (Ambrosia) grains detected in the atmosphere of Istanbul, Turkey. The dynamic migration of this invasive taxon is a serious environmental issue. Ragweed pollen is highly allergenic and causes sensitization in patients at low concentrations. At present, there is no floristic evidence of this taxon in the region. Aerobiological records presented here, though, indicate a local source. Moreover, we argue that ragweed pollen comes from distant sources through air mass movements. The analysis concerns the ragweed season 2007. Pollens were sampled with a Burkard trap and identified at a magnification of 400 ×. Grains were counted on 12 transverse traverses to estimate bi-hourly changes in concentrations. The peak day was on August 28 with 20 grainsm(-3). Ragweed was observed on 22 days during August and September 2007. On all days, except one, the daily average concentration was below 10 grainsm(-3). Diurnal bi-hourly ragweed concentrations reached a maximum at 11:00 EET. Relatively high concentrations were observed between 21:00 and 01:00 EET. This allowed for the assumption of a local and a remote ragweed pollen source. We used HYSPLIT backward trajectory ensembles to identify possible sources on peak day. A frequency analysis of back trajectories covering the entire ragweed season followed. Firstly, possible local sources were the Istanbul Province and Turkish Thrace; secondly, a likely over-regional source was Bulgaria; and lastly, remote sources of ragweed pollen were the Ukraine, the Russian coastal region of the Black Sea and Moldova. This study provides evidence that pollens detected on our receptor site stem from combined local and remote origins.