Highly water-resistant paper via infiltration with polymeric microspheres from nanocellulose-stabilized plant oil-derived monomer.

Sustainable strategies to improve the water resistance of cellulose paper are actively sought. In this work, polymeric microspheres (PMs), prepared through emulsion polymerization of cellulose nanofibers stabilized rubber seed oil-derived monomer, were investigated as coatings on corrugated medium paper (CMP). After infiltrating porous paper with PMs, the water-resistant corrugated papers (WRCPn) with enhanced mechanical properties were obtained. When 30 wt% PMs were introduced, WRCP30 turned out to be highly compacted with an increased water contact angle of 106.3° and a low water vapor transmission rate of 81 g/(m2 d) at 23 °C. Meanwhile, the tensile strength of WRCP30 increased to 22.2 MPa, a 4-fold increase from CMP. When tested in a well-hydrated state, 71% of its mechanical strength in the dry state was maintained. Even with a low content of 10 wt% PMs, WRCP10 also exhibited stable tensile strength and water wettability during the cyclic soaking-drying process. Thus, the plant oil based sustainable emulsion polymers provide a convenient route for enhancing the overall performance of cellulose paper.

Microfluidic Paper-Based Device Incorporated with Silica Nanoparticles for Iodide Quantification in Marine Source Dietary Supplements.

Iodine is an essential micronutrient for humans due to its fundamental role in the biosynthesis of thyroid hormones. As a key parameter to assess health conditions, iodine intake needs to be monitored to ascertain and prevent iodine deficiency. Iodine is available from various food sources (such as seaweed, fish, and seafood, among others) and dietary supplements (multivitamins or mineral supplements). In this work, a microfluidic paper-based analytical device (µPAD) to quantify iodide in seaweed and dietary supplements is described. The developed µPAD is a small microfluidic device that emerges as quite relevant in terms of its analytical capacity. The quantification of iodide is based on the oxidation of 3,3',5,5'-tetramethylbenzidine (TMB) by hydrogen peroxide in the presence of iodine, which acts as the catalyst to produce the blue form of TMB. Additionally, powder silica was used to intensify and uniformize the colour of the obtained product. Following optimization, the developed µPAD enabled iodide quantification within the range of 10-100 µM, with a detection limit of 3 µM, and was successfully applied to seaweeds and dietary supplements. The device represents a valuable tool for point-of-care analysis, can be used by untrained personnel at home, and is easily disposable, low-cost, and user-friendly.

Flexible, Biodegradable, and Wireless Magnetoelectric Paper for Simple In Situ Personalization of Bioelectric Implants.

Bioelectronic implants delivering electrical stimulation offer an attractive alternative to traditional pharmaceuticals in electrotherapy. However, achieving simple, rapid, and cost-effective personalization of these implants for customized treatment in unique clinical and physical scenarios presents a substantial challenge. This challenge is further compounded by the need to ensure safety and minimal invasiveness, requiring essential attributes such as flexibility, biocompatibility, lightness, biodegradability, and wireless stimulation capability. Here, a flexible, biodegradable bioelectronic paper with homogeneously distributed wireless stimulation functionality for simple personalization of bioelectronic implants is introduced. The bioelectronic paper synergistically combines i) lead-free magnetoelectric nanoparticles (MENs) that facilitate electrical stimulation in response to external magnetic field and ii) flexible and biodegradable nanofibers (NFs) that enable localization of MENs for high-selectivity stimulation, oxygen/nutrient permeation, cell orientation modulation, and biodegradation rate control. The effectiveness of wireless electrical stimulation in vitro through enhanced neuronal differentiation of neuron-like PC12 cells and the controllability of their microstructural orientation are shown. Also, scalability, design flexibility, and rapid customizability of the bioelectronic paper are shown by creating various 3D macrostructures using simple paper crafting techniques such as cutting and folding. This platform holds promise for simple and rapid personalization of temporary bioelectronic implants for minimally invasive wireless stimulation therapies.

Effect of enzymatic treatment on Eucalyptus globulus vessels passivation.

Hardwood vessel elements generate problems in industrial uncoated wood-free printing paper operation, causing vessel picking and ink refusal. These problems are mitigated using mechanical refining at the cost of paper quality. Vessel enzymatic passivation, altering its adhesion to the fiber network and reducing its hydrophobicity is a way of improving paper quality. The object of this paper is to study how the enzymatic treatment by xylanase and by an enzymatic cocktail containing cellulases and laccases affect elemental chlorine free bleached Eucalyptus globulus vessel and fiber porosities, bulk, and surface chemical compositions. Thermoporosimetry revealed the vessel structure to be more porous, surface analysis showed its lower O/C ratio and bulk chemistry analysis its higher hemicellulose content. Enzymes had different effects on porosity, bulk and surface composition of fibers and vessels, affecting vessel adhesion and hydrophobicity. Vessel picking count decreased 76% for papers containing vessels treated with xylanase and 94% for the papers with vessels treated with the enzymatic cocktail. Fiber sheet samples had lower water contact angle (54.1º) than vessels rich sheets (63.7º), that reduced with xylanase (62.1º) and cocktail (58.4º). It is proposed that differences in vessel and fiber porosity structures affect the enzymatic attacks, eventually causing vessel passivation.

Flotation de-inking for recycling paper: contrasting the effects of three mineral oil-free offset printing inks on its efficiency.

Paper for recycling has become a promising raw material for the pulp and paper industry due to its low cost and because it is conducive to sustainable development. Unfortunately, recycled paper contains a high volume of printed paper that is difficult to deink, which restricts its applications. Flotation deinking plays an essential role in the product quality and process cost of wastepaper recycling. This study was performed to evaluate the deinkability of environmentally friendly offset inks by flotation deinking. For this purpose, three mineral oil free series of four-color inks, namely, hybrid light emitting diode ultraviolet (LED-UV), LED-UV, and vegetable oil-based inks, were printed on white lightweight coated papers under laboratory conditions. The deinking methodology involves repulping, deinking agent treatment, flotation, hand sheet making, and evaluation of the produced hand sheets. The obtained results indicated that the hybrid LED-UV prints had the best deinkability. After flotation deinking, the deinking efficiency and the whiteness of the hybrid LED-UV ink increased by 58.1% and 47.6%, respectively. LED-UV ink had a 46.9% increase in the deinking efficiency and a 37.0% increase in the whiteness of the hand sheet. The deinking efficiency of the vegetable oil-based ink was the lowest, at 42.1%, and the whiteness of the hand sheet increased only by 23.8%. The particle size distribution analysis demonstrated that the hybrid LED-UV four-color ink exhibited a larger value of the average particle size than the two other. Scanning electron microscopy revealed that the hybrid LED-UV ink particles on the surface of the fibers were the least abundant after deinking. The physical strength properties of the hand sheets, including tensile index, folding resistance, and interlayer bonding strength of the hybrid LED-UV, LED-UV inks, and vegetable oil-based inks, increased.

Determination of phosphorus in water and chemical fertilizer samples using a simple drawing microfluidic paper-based analytical device.

A simple one-step drawing for the cost-effective fabrication of microfluidic paper-based analytical devices (µPADs) for the determination of phosphate content in water and fertilizer samples is presented in this paper. The hydrophobic barrier of µPAD was patterned using a 2-mm tip marker pen using a transparent acrylic sheet template. The molybdenum blue reaction using ascorbic acid as a reducing agent was used. A pre-concentration step of samples is proposed to improve the sensitivity of the measurement. The blue complex produced on the µPADs was recorded using a smartphone camera. The color intensities (red, green, blue and gray) were analyzed using ImageJ program. The proposed µPAD method provides a linear calibration range from 0 to 100 mg L-1 P. The limit of detection (LOD) was found to be 0.7 mg L-1 P with a precision of 3.1%RSD for 50 mg L-1 P (n = 10). The proposed method was successfully applied to the determination of phosphorus contents in water and liquid chemical fertilizer samples. The results obtained from µPAD agreed with a spectrophotometric method using paired t test at a 95% confidence level.

A Three-Reagent "Green" Paper-Based Analytical Device for Solid-Phase Spectrometric and Colorimetric Determination of Dihydroquercetin.

Microfluidic paper-based analytical devices (µPADs) represent one of the promising green analytical strategies for low-cost and simple determination of various analytes. The actual task is the development of such devices for quantitation of antioxidants, e.g., flavonoids. In this paper, possibilities of a novel three-reagent µPAD including silver nitrate, 4-nitrophenyldiazonium tetrafluoroborate, and iron(III) chloride as reagents are assessed with respect to the determination of dihydroquercetin. It is shown that all the three reagents produce different colorimetric responses that can be detected by a mini-spectrophotometer-monitor calibrator or by a smartphone. The method is applicable to direct measuring high contents of dihydroquercetin (the linearity range is 0.026-1 mg mL-1, and the limit of detection is 7.7 µg mL-1), which is favorable for many dietary supplements. The analysis of a food supplement was possible with the relative standard deviations of 9-26%, which is satisfactory for quantitative and semiquantitative determinations. It was found that plotting a calibration graph in 3D space of the three reagents' responses allows us to distinguish dihydroquercetin from its close structural analogue, quercetin.

Moringa oleifera seeds-removed ripened pods as alternative for papersheet production: antimicrobial activity and their phytoconstituents profile using HPLC.

In the present study, and for the waste valorization, Moringa oleifera seeds-removed ripened pods (SRRP) were used for papersheet production and for the extraction of bioactive compounds. Fibers were characterized by SEM-EDX patterns, while the phytoconstituents in ethanol extract was analyzed by HPLC. The inhibition percentage of fungal mycelial growth (IFMG) of the treated Melia azedarach wood with M. oleifera SRRP extract at the concentrations of 10,000, 20,000, and 30,000 µg/mL against the growth of Rhizoctonia solani and Fusarium culmorum was calculated and compared with fluconazole (25 µg). The produced papersheet was treated with the ethanol extract (4000, 2000, and 1000 µg/mL) and assayed for its antibacterial activity against Agrobacterium tumefaciens, Erwinia amylovora, and Pectobacterium atrosepticum by measuring the inhibition zones and minimum inhibitory concentrations (MICs). According to chemical analysis of M. oleifera SRRP, benzene:alcohol extractives, holocellulose, lignin, and ash contents were 7.56, 64.94, 25.66 and 1.53%, respectively, while for the produced unbleached pulp, the screen pulp yield and the Kappa number were 39% and 25, respectively. The produced papersheet showed tensile index, tear index, burst index, and double fold number values of 58.8 N m/g, 3.38 mN m2/g, 3.86 kPa m2/g, and 10.66, respectively. SEM examination showed that the average fiber diameter was 16.39 µm, and the mass average of for elemental composition of C and O by EDX were, 44.21%, and 55.79%, respectively. The main phytoconstituents in the extract (mg/100 g extract) by HPLC were vanillic acid (5053.49), benzoic acid (262.98), naringenin (133.02), chlorogenic acid (66.16), and myricetin (56.27). After 14 days of incubation, M. oleifera SRRP extract-wood treated showed good IFMG against R. solani (36.88%) and F. culmorum (51.66%) compared to fluconazole, where it observed 42.96% and 53.70%, respectively. Moderate to significant antibacterial activity was found, where the minimum inhibitory concentration (MIC) values were 500, 650, and 250 µg/mL against the growth of A. tumefaciens, E. amylovora, and P. atrosepticum respectively, which were lower than the positive control used (Tobramycin 10 µg/disc). In conclusion, M. oleifera SRRP showed promising properties as a raw material for pulp and paper production as well as for the extraction of bioactive compounds.

Pulp Enhancement of Oil Palm Empty Fruit Bunches (OPEFBs) via Biobleaching by Using Xylano-Pectinolytic Enzymes of Bacillus amyloliquefaciens ADI2.

The present work reports the biobleaching effect on OPEFB pulp upon utilisation of extracellular xylano-pectinolytic enzymes simultaneously yielded from Bacillus amyloliquefaciens ADI2. The impacts of different doses, retention times, pH, and temperatures required for the pulp biobleaching process were delineated accordingly. Here, the OPEFB pulp was subjected to pre-treatment with xylano-pectinolytic enzymes generated from the same alkalo-thermotolerant isolate that yielded those of higher quality. Remarkable enhanced outcomes were observed across varying pulp attributes: for example, enzyme-treated pulp treated to chemical bleaching sequence generated improved brightness of 11.25%. This resulted in 11.25% of less chlorine or chemical consumption required for obtaining pulp with optical attributes identical to those generated via typical chemical bleaching processes. Ultimately, the reduced consumption of chlorine would minimise the organochlorine compounds found in an effluent, resulting in a lowered environmental effect of paper-making processes overall as a consequence. This will undoubtedly facilitate such environmentally-friendly technology incorporation in the paper pulp industry of today.

Active Barrier Coating for Packaging Paper with Controlled Release of Sunflower Oils.

The use of paper as a sustainable packaging material is favored, but it lacks sufficient barrier properties in terms of water repellence and oil resistance. Novel approaches consider active packaging materials or coatings with controlled release providing additional functionality for delivery of specific components to the surface. In this study, the development of a waterborne coating with organic nanoparticles and encapsulated sunflower oils is presented as a system for thermal release of the oil and on-demand tuning of the final barrier properties of the paper substrate. After synthesis of the nanoparticles, it seems that the encapsulation of various grades of sunflower oil (i.e., either poly-unsaturated or mono-unsaturated) strongly affects the encapsulation efficiency and thermal release profiles. The water contact angles are controlled by the oil release and chemical surface composition of the coating upon thermal heating. The oil resistance of the paper improves as a more continuous oil film is formed during thermal release. In particular, the chemical surface composition of the paper coatings is detailed by means of micro-Raman spectroscopy and surface imaging, which provide an analytical quantification tool to evaluate surface coverage, oil delivery, and variations in organic coating moieties.

Simultaneous and sensitive detection of multiple small biological molecules by microfluidic paper-based analytical device integrated with zinc oxide nanorods.

In this work, ZnO nanorods (ZnO NRs) with different sizes were hydrothermally grown on the surface of Whatman filter paper for the fabrication of a microfluidic paper-based device (µPAD) for the simultaneous detection of glucose and uric acid. As dual enzymatic reaction was employed for the colorimetric detection in this µPAD, the presence of ZnO NRs promoted the enzyme immobilization thus significantly enhancing the colorimetric signal. The coffee ring effect was effectively conquered by the uniform distribution of ZnO NR as well as a specialized double-layered µPAD design. Meanwhile, two color indicators with distinct colors were used to provide complementary results to better quantify the concentration of the analytes by naked eye. As a result, two linear calibration curves were obtained for the detection of glucose (0.01-10 mmol L-1) and uric acid (0.01-5 mmol L-1), along with a LOD of 3 µmol L-1 for glucose and 4 µmol L-1 for uric acid, respectively. The practical usefulness of the proposed µPAD was further validated by the simultaneous analysis of glucose and uric acid in serum samples and urine samples.

Rapid and simple colorimetric detection of hydrogen sulfide using an etching-resistant effect on silver nanoprisms.

A fast and sensitive colorimetric paper sensor has been developed using silver nanoprisms (Ag NPRs) with an edge length of ~50 nm for the detection of free H2S gas. We prepared two types of Ag NPRs-coated H2S sensing papers: a multi-zone patterned paper for passive (diffusion mode), and a single-zone patterned paper for pumped mode of H2S gas. The change in color intensity was quantitatively analyzed of Ag NPRs-coated paper after KCl treatment depending on the concentration of H2S gas, from yellow to purplish brown. As a result, Ag NPRs-coated H2S sensing paper showed good sensitivity with a linear range of 1.03 to 32.9 µM H2S, high selectivity, and good reproducibility and stability, together with a fast response time of 1 min. The developed H2S sensing paper was applied to detect the free H2S gas released from three types of garlic including crushed, peeled, and fresh garlic. Therefore, it can be utilized as a simple, fast, and reliable tool for on-site colorimetric detection of free H2S gas for quality control of dietary supplements and exhaled breath analysis.Graphical abstract.

Dopamine-polyethyleneimine co-deposition cellulose filter paper for α-Glucosidase immobilization and enzyme inhibitor screening.

In this work, cellulose filter paper (CFP), which is inexpensive and commercially available, was used as the carrier, and the immobilized α-glucosidase was obtained by two steps: firstly, the surface of CFP was modified by polydopamine/polyethyleneimine (PDA/PEI) co-deposition method to obtain CFP-PDA/PEI with a uniform coating of rich positive charge; subsequently, α-glucosidase was immobilized on the CFP-PDA/PEI by electrostatic adsorption. The free enzyme and immobilized enzyme have the same optimal temperature (70℃) and pH (8.0), and their Km is similar, which is 2.2 and 2.8, respectively. These results show that the immobilization process does not change the properties of the enzyme greatly. The immobilized enzyme still maintains 75.6% of its initial activity after 10 repeated uses, showing good reusability. The excellent repeatability (RSD = 2.2%, n = 5) and the verification of competitive inhibitor (acarbose) illustrates the reliability of the immobilized enzymes for enzyme inhibitor screening. Finally, combined with CE, a screening method based immobilized α-glucosidase was proposed and applied to screen the α-glucosidase inhibitory from 10 kinds of Traditional Chinese medicines (TCMs) in vitro. The results indicated that the method was a very effective tool for screening potential α-glucosidase inhibitors from TCMs.

Value-added switchgrass extractives for reduction of Escherichia coli O157:H7 and Salmonella Typhimurium populations on Formica coupons.

Recurring outbreaks linked to Escherichia coli O157:H7-contaminated lettuce and Salmonella enterica-contaminated sprouts highlight the need for improved food safety measures. The aim of this study was to determine the ability of a bio-based antimicrobial extract prepared from switchgrass, a dedicated energy crop, to reduce E. coli O157:H7 and S. Typhimurium populations on Formica coupons, a model food-contact surface. Overnight cultures of ~7 log CFU/mL E. coli O157:H7 and S. Typhimurium, air-dried on Formica coupons were treated with 0.625% NaClO, 70% ethanol, sterile water or different batches of switchgrass extractives (SE1, SE2, and SE3) for up to 30 min. E. coli O157:H7 was reduced by 4.43 log CFU/mL after 1 min by SE3, and to non-detectable levels after 1 min by all other treatments. Populations of S. Typhimurium LT2 (15-min drying) were reduced by 3.30 log CFU/mL with 70% ethanol, 5.38 log CFU/mL with SE1, and to non-detectable levels with 0.625% NaClO after 1 min, while S. Typhimurium ATCC 23564 (1-h drying) was non-detectable after 1 min by all treatments. Under soiled conditions, 10-min treatment with SE1 and 70% ethanol reduced both bacteria to non-detectable levels. Studies with concentrated switchgrass extractives combined with various other natural disinfectants or in hurdle approaches warrant further investigation.

Visual paper-based sensor for the highly sensitive detection of caffeine in food and biological matrix based on CdTe-nano ZnTPyP combined with chemometrics.

Caffeine naturally occurs in tea and cocoa, which is also used as an additive in beverages and has pharmacological effects such as refreshing, antidepressant, and digestion promotion, but excessive caffeine can cause harm to the human body. In this work, based on the specific response between nano zinc 5, 10, 15, 20-tetra(4-pyridyl)-21H-23H-porphine (nano ZnTPyP)-CdTe quantum dots (QDs) and caffeine, combined with chemometrics, a visual paper-based sensor was constructed for rapid and on-site detection of caffeine. The fluorescence of QDs can be quenched by nano ZnTPyP. When caffeine is added to the system, it can pull nano ZnTPyP off the surface of the QDs to achieve fluorescence recovery through electrostatic attraction and nitrogen/zinc coordination. The detection range is 5 × 10-11~3 × 10-9 mol L-1, and the detection limit is 1.53 × 10-11 mol L-1 (R2 = 0.9990) (S/N = 3). The paper-based sensor constructed exhibits good results in real samples, such as tea water, cell culture fluid, newborn bovine serum, and human plasma. Therefore, the sensor is expected to be applied to the rapid instrument-free detection of caffeine in food and biological samples.Graphical abstract.

Fabrication of a "Selenium Signature" Chemical Probe-Modified Paper Substrate for Simultaneous and Efficient Determination of Biothiols by Paper Spray Mass Spectrometry.

Significant efforts have been made to develop robust and reliable methods for simultaneous biothiols determination in different matrices, but there still exist the problems such as easy oxidation, tedious derivatization, and difficulty in discrimination, which brings unsatisfactory results in their accuracy and fast quantification in biological samples. To overcome these problems, a simultaneous biothiols detection method combining a "selenium signature" chemical probe and paper spray mass spectrometry (PS-MS) was proposed. In the strategy, the modified-paper substrate is used to enhance the analytical performance. Chemical probe Ebselen-NH2 that has a specific response to biothiols was designed and covalently fixed on the surface of an oxidized paper substrate. By the identification of derivatized product with distinctive selenium isotope distribution and employment of the optimized PS-MS method, qualitative and quantitative analysis of five biothiols including glutathione (GSH), cysteine (Cys), cysteinylglycine (CysGly), N-acetylcysteine (Nac), and homocysteine (Hcy) were realized. Biothiols in plasma and cell lysates were measured with satisfactory results. The established method not only provides a novel protocol for simultaneous determination of biothiols, but also is helpful for understanding the biological and clinical roles played by these bioactive small molecules.

Rapid measurement of total polyphenol content in tea by kinetic matching approach on microfluidic paper-based analytical devices.

In this work, a facile kinetic matching approach for total polyphenol content (TPC) measurement was developed based on the adoption of microfluidic paper-based analytical devices with symmetric channel distribution. A set of Folin-Ciocalteu reactions performed on the same paper chip were activated all at the same time through synchronized filling of sodium carbonate solution among individual channels. Gallic acid was found valid as a standard compound for kinetic matching measurement of tea samples. TPC of tea infusions was successfully measured within ten minutes without any complexed time control procedure needed. Under the optimized conditions, the new developed method showed good linearity in the TPC range of 10-100 mg/L (r > 0.9955) and the inter-chip precision was 5.6% (n = 11). The results measured with the new developed approach were in good agreement with those with the conventional FC assay.

Horticultural Plant Residues as New Source for Lignocellulose Nanofibers Isolation: Application on the Recycling Paperboard Process.

Horticultural plant residues (tomato, pepper, and eggplant) were identified as new sources for lignocellulose nanofibers (LCNF). Cellulosic pulp was obtained from the different plant residues using an environmentally friendly process, energy-sustainable, simple, and with low-chemical reagent consumption. The chemical composition of the obtained pulps was analyzed in order to study its influence in the nanofibrillation process. Cellulosic fibers were subjected to two different pretreatments, mechanical and TEMPO(2,2,6,6-Tetramethyl-piperidin-1-oxyl)-mediated oxidation, followed by high-pressure homogenization to produce different lignocellulose nanofibers. Then, LCNF were deeply characterized in terms of nanofibrillation yield, cationic demand, carboxyl content, morphology, crystallinity, and thermal stability. The suitability of each raw material to produce lignocellulose nanofibers was analyzed from the point of view of each pretreatment. TEMPO-mediated oxidation was identified as a more effective pretreatment to produce LCNF, however, it produces a decrease in the thermal stability of the LCNF. The different LCNF were added as reinforcing agent on recycled paperboard and compared with the improving produced by the industrial mechanical beating. The analysis of the papersheets' mechanical properties shows that the addition of LCNF as a reinforcing agent in the paperboard recycling process is a viable alternative to mechanical beating, achieving greater reinforcing effect and increasing the products' life cycles.

Paper-Based Constant Potential Electrochemiluminescence Sensing Platform with Black Phosphorus as a Luminophore Enabled by a Perovskite Solar Cell.

Exploring efficient luminophores in the electrochemiluminescence (ECL) system is highly desired to pursue a sensitive ECL sensing platform. Herein, the black phosphorus nanosheets (BP NSs) with excellent ECL properties are investigated and serve as the luminophore with the coreactant of peroxydisulfate (S2O82-) solution. Moreover, owing to the overlapping of emission and absorbance spectra, effective resonance energy transfer (RET) is realized between the BP NSs and the introduced Au nanoparticles. In order to achieve the portable and miniaturized developing trends for the paper-based ECL sensing platform, a paper-based perovskite solar cell (PSC) device is designed to act as the power source to replace the commonly utilized expensive and cumbersome electrochemical workstation. Benefiting from that, a PSC driven paper-based constant potential ECL-RET sensing platform is constructed, thereby realizing sensitive microRNAs (miRNAs) detection. What's more, to attain the preferable analytical performance, the duplex-specific nuclease (DSN) is also introduced to assist the target recycling signal amplification strategy. Based on this, highly sensitive detection of miRNA-107 with a range from 0.1 pM to 15 nM is achieved by this designed sensing platform. Most importantly, this work not only pioneers a precedent for developing a high-sensitivity PSC triggered ECL sensing platform but also explores the application prospect of BP nanomaterial in the field of bioanalysis.

Facile Approach for Ecofriendly, Low-Cost, and Water-Resistant Paper Coatings via Palm Kernel Oil.

Paper-based packaging is widely employed in industries ranging from food to beverages to pharmaceuticals because of its attractive advantages of biodegradability, recyclability, good strength, low cost, and lightweight. However, paper products usually have poor water barrier resistance properties because of paper and fibers porous microstructure. In this study, an ecofriendly water-resistant (hydrophobic) oil from biological origin, namely, palm kernel oil (PKO) was used to coat paper by using a facile and cost-effective dip-casting approach. PKO formulation was prepared by mixing with a solvent and furfuryl alcohol (FA). The water resistance, structural properties, and thermal and mechanical properties of the coated papers obtained under different processing conditions were reported and compared to understand the performance of coated paper. Contact angle (CA), Fourier transform infrared (FTIR), and thermal gravimetry (TGA) were used for analysis and characterization of coated papers. Data from contact angle measurements showed that the PKO formulation could considerably improve the liquid water barrier property of the paper, with a measured water contact angle (CA) of ∼120° and reduce the water vapor transmission rate (WVTR) by 22%. This novel, green, low-cost, and water-resistant paper coating made with biological and biodegradable oil is a potential candidate for replacing petroleum-based coatings used in a broad range of applications and will also be able to make an additional full use of the palm kernel oil.