INFLUENCE OF AGING, BEVERAGES, AND MOUTH WASH SOLUTIONS ON THE MICROSTRUCTURAL AND COLOR STABILITY OF DIFFERENT DENTAL CERAMICS: AN IN VITRO STUDY.

Рurроse - to evaluate the influence of aging, beverages, and mouthwash solutions on the microstructural and color stability of three CAD/CAM ceramic materials. In total, 87 specimens (7×5×1.5 mm) were prepared from 3 CAD/CAM ceramic groups, Lithium Disilicate glass ceramic (IPS e.max CAD), Extra translucent zirconia (VITA YZ), and Resin Nanoceramic (Cerasmart 270). All the materials were A2 or equivalent shades. After hydrothermal aging in distilled water at 5 C to 55 C for (10.000 cycles). The samples were randomly allocated into 3 groups (n=27) and immersion (staining) for one week in 3 different solutions coffee, green tea, and chlorhexidine. The baseline measurements of ceramic discs were recorded for color change and 2 samples of each group sent for SEM (microstructure) images before aging and staining. The second measurement was recorded after 10000 thermocycling and immersion in staining agents for 7 days. Statistical analysis were performed with an independent Kruskal-wallis test . The significant level was set at P≤0.05. ∆E values for lithium Disilicate after immersion in coffee, green tea and chlorhexidine gluconate were 3.167, 1.847 and 2.022, respectively. corresponding ∆E values for VITA XT were 3.438, 4.201 and 2.267. meanwhile Cerasmart shows more sensitivity for staining than LD and VITA of 4.454, 2.926 and 2.933. Within limitation of this study lithium disilicate showed the best color stability with values less than perception threshold. VITA and Cerasmart show higher sensitivity for staining with VITA more affected by green tea (Higher than clinically accepted threshold) and Cerasmart more affected by coffee (higher than clinically accepted threshold).

Oviposition Deterrent Activity of Some Wild Plants for Adult Females of Chrysomya albiceps with Medical and Veterinary Importance.

<b>Background and Objective:</b> <i>Chrysomya albiceps</i> is widely spread worldwide, causing myiasis in both humans and animals and playing a mechanical role in the spreading of helminths, viruses and bacteria. Searching for new and safe alternative control methods is very important to eliminate the transmission of pathogens. This study aims to determine the oviposition-deterrent activity of <i>Juniperus procera</i>, <i>Artemisia absinthium</i>, <i>Rosmarinus officinalis</i> and <i>Hypoestes forskaolii</i> wild plants against adult <i>Chrysomya albiceps</i>. <b>Materials and Methods:</b> The effect of plant extracts from <i>Juniperus procera</i>, <i>Artemisia absinthium</i>, <i>Rosmarinus officinalis</i> and <i>Hypoestes forskaolii</i> plants were tested against adult females of <i>Chrysomya albiceps</i> for oviposition deterrent or repellency. These extracts resulted in oviposition deterrent efficacy for adult females of <i>C. albiceps</i> based on the plant type, plant part (leaves or stems), extract type (methanol, acetone and petroleum ether) and tested dose. <b>Results:</b> The highest anti-oviposition activity against <i>C. albiceps</i> females presented from <i>A. absinthium</i> stems acetone extract at a dose of 1 mg cm² by 100 %, while at 0.5 mg cm² recorded remarkable repellency by 86.7% as compared with the control treatment. According to the dose-response relationship, <i>A. absinthium</i> methanol and acetone extracts were ED₅₀ values of 0.85, 0.319 mg cm² (leaves) and 1.88, 0.576 mg cm² (stems), followed by <i>J. procera</i> methanol extract by 0.983 mg cm² (leaves) and 0.98 mg cm² (stems), respectively achieved highest oviposition deterrent efficiency as compared with other extracts. <b>Conclusion:</b> The high repellency activities of these extracts can be utilized to stop <i>C. albiceps</i> flies from laying eggs on wounds and transmitting myiasis diseases to humans and animals and could potentially replace pesticides used in the future control programs of flies.

Ethnoveterinary medicinal plants and their utilization by the people of Soro District, Hadiya Zone, southern Ethiopia.

BACKGROUND: Ethnoveterinary studies are important to maintain the sustainability of livestock health and support people's livelihoods through the provision of food, maintaining livestock health, and other biological resources. This study was carried out in Soro District, southern Ethiopia, to identify, document and analyse plant species with ethnoveterinary uses along with the associated indigenous and local knowledge. MATERIALS AND METHODS: Informants were selected using purposive (key informants) and systematic random sampling (general informants) methods. Data on ethnoveterinary plants and their uses were collected through semi-structured interviews, guided field walks, 13 focus group discussions with five to seven members in each and participant observation. Informant consensus factor and fidelity level were computed to identify the most common livestock ailment categories and the best plant species with ethnoveterinary use, respectively. Preference ranking methods were used to identify the potentially effective ethnoveterinary medicinal plants for the most frequently reported livestock ailments. The use diversity of multipurpose plants with ethnoveterinary importance was analysed using the analytical methods of ethnobotany including priority ranking, comparisons and important indices. The T-test statistic was used to compare knowledge differences among different social groups. RESULTS: A total of 132 plant species in 120 genera and 61 families were reported by informants as having ethnoveterinary uses. The plants are said to be used by the local communities in various ways to treat 50 livestock health problems. Higher number of informants (23.77%) cited Momordica foetida for the treatment of 16 livestock ailments. The highest informant consensus value for this species is associated with its use for treating blackleg in cattle; Nicotiana tabacum was cited for the treatment of 15 livestock ailments mainly recommended for the Lumpy Skin Disease/Ailment of bovines; Croton macrostachyus for treatment of 13 livestock ailments including wooden tongue, FMD in bovines; and Gymnanthemum amygdalinum for nine ailments mainly diarrhoea of all livestock types. Achyranthes aspera is claimed to provide the most effective treatment for Aspiration pneumonia (severe coughing in bovines, sheep and goats) alone, while Croton macrostachyus, Ximenia americana, Allium sativum and Juniperus procera were indicated as potential plant species to treat Lumpy Skin Disease in bovines in the order given. The fidelity level analysis showed that Datura stramonium, Dodonaea viscosa subsp. angustifolia and Asparagus africanus were potential medicinal plant species to treat the respective ailments of rabies, Peste des petits ruminants (PPR) and evil eye/spirit. Multipurpose plant species including Prunus africanus, Combretum molle and Afrocarpus falcatus have been highly threatened as indicated by direct matrix ranking mainly due to collection of fuel wood, construction materials and making household utensils, and farm implements rather than for other uses. CONCLUSION: Soro District has rich and diversified livestock herbal medicinal resources, and indigenous knowledge of remedy preparations and applications is transmitted through generation lines. This resource faces anthropogenic threats with deforestation being the leading factor. Consequently, ethnoveterinary medicinal plants continue to decline before adequate and proper scientific documentation and testing are made. There is a dire need for planning and implementation of appropriate in situ and ex situ conservation strategies and to strive towards ensuring the survival and sustainable utilization of such important plant resources of Soro District. This must be supported by further documentation of the associated indigenous knowledge and pharmacological testing of the key promising species including Balanites aegyptiaca (novel species/NS to treat specific ailment), Brugmansia suaveolens (novel species/NS reported first to treat Livestock ailments/LsAs), Euclea divinorum (NS to treat specific ailments), Grevillea robusta (NS), Hagenia abyssinica (NS for the reported specific ailment), Pentanema confertiflorum (NS), Juniperus procera (NS), Maesa lanceolata (NS), Millettia ferruginea (NS for reported specific ailments), Schrebera alata/NS, Securidaca longepedunculata, Spiniluma oxyacantha/NS, Vepris nobilis (novel species reported first to treat LsAs), Zanthoxylum asiaticum /NS and Ximenia americana (NS for specific ailments). This ethnoveterinary study attempted to fill part of the gaps concerning the prevalent livestock health problems and the associated indigenous and local knowledge in the area.

Calotropis procera extract inhibits prostate cancer through regulation of autophagy.

Current treatment options available for prostate cancer (PCa) patients have many adverse side effects and hence, new alternative therapies need to be explored. Anticancer potential of various phytochemicals derived from Calotropis procera has been studied in many cancers but no study has investigated the effect of leaf extract of C. procera on PCa cells. Hence, we investigated the effect of C. procera leaf extract (CPE) on cellular properties of androgen-independent PC-3 and androgen-sensitive 22Rv1 cells. A hydroalcoholic extract of C. procera was prepared and MTT assay was performed to study the effect of CPE on viability of PCa cells. The effect of CPE on cell division ability, migration capability and reactive oxygen species (ROS) production was studied using colony formation assay, wound-healing assay and 2',7'-dichlorodihydrofluorescein diacetate assay, respectively. Caspase activity assay and LDH assay were performed to study the involvement of apoptosis and necrosis in CPE-mediated cell death. Protein levels of cell cycle, antioxidant, autophagy and apoptosis markers were measured by western blot. The composition of CPE was identified using untargeted LC-MS analysis. Results showed that CPE decreased the viability of both the PCa cells, PC-3 and 22Rv1, in a dose- and time-dependent manner. Also, CPE significantly inhibited the colony-forming ability, migration and endogenous ROS production in both the cell lines. Furthermore, CPE significantly decreased NF-κB protein levels and increased the protein levels of the cell cycle inhibitor p27. A significant increase in expression of autophagy markers was observed in CPE-treated PC-3 cells while autophagy markers were downregulated in 22Rv1 cells after CPE exposure. Hence, it can be concluded that CPE inhibits PCa cell viability possibly by regulating the autophagy pathway and/or altering the ROS levels. Thus, CPE can be explored as a possible alternative therapeutic agent for PCa.

Ethnobotanical, ecological and health risk assessment of some selected wild medicinal plants collected along mafic and Ultra Mafic rocks of Northwest Pakistan.

The current study investigated wild plant resources and health risk assessment along with northern Pakistan's mafic and ultramafic regions. Ethnobotanical data was collected through field visits and semi-structured questionnaire surveys conducted from local inhabitants and healers. Six potentially toxic elements (PTEs) such as lead (Pb), cadmium (Cd), nickel (Ni), chromium (Cr), manganese (Mn), and zinc (Zn) were extracted with acids and analyzed using atomic absorption spectrophotometer (AAS, Perkin Elmer-7000) in nine selected wild medicinal plants. Contamination factor (CF), pollution load index (PLI), estimated daily intake (EDI), target hazard quotient (THQ), and hazard index (HI) were used to determine the health risk assessment of the studied medicinal plants. The results showed that the selected medicinal plants were used for the treatments of cough, joint swelling, cardiovascular disorders, toothaches, diabetes, and skin pimples by the local inhabitants due to their low-cost and easy accessibility. The concentrations of Pb (3.4-53 mg kg-1), Cd (0.03-0.39 mg kg-1), Ni (17.5-82 mg kg-1), Cr (29-315 mg kg-1), Mn (20-142 mg kg-1), and Zn (7.4-64 mg kg-1) in the studied medicinal plants were found above the safe limits (except Zn) set by WHO/FAO/USEPA (1984/2010). The Pb contamination factor was significantly (p < 0.05) higher in A. modesta (7.84) and D. viscosa (6.81), and Cd contamination factor was significantly higher in C. officinalis (26.67), followed by A. modesta (8.0) mg kg-1. Based on PTE concentrations, the studied plants are considered not suitable for human consumption purposes. Pollution load index values for A. modesta, A. barbadensis, A. caudatus, A. indica, C. procera (2.93), D. viscosa (2.79), and C. officinalis (2.83), R. hastatus (3.12), and Z. armatum were observed as 1.00, 2.80, 2.29, 2.29, 2.93, 2.79, 2.83, 3.12 and 2.19, respectively. Hazard index values were in order of R. hastatus (1.32 × 10-1) ˃ C. procera (1.21 × 10-1) ˃ D. viscosa (1.10 × 10-1) ˃ A. caudatus (9.11 × 10-2) ˃ A. barbadensis (8.66 × 10-2) ˃ Z. armatum (7.99 × 10-2) ˃ A. indica (6.87 × 10-2) ˃ A. modesta (5.6 × 10-2) ˃ C. officinalis (5.42 × 10-2). The health risk index values suggested that consumption of these plants individually or in combination would cause severe health problems in the consumers. Pearson's correlation results showed a significant correlation (p ≤ 0.001) between Zn and Mn in the studied medicinal plants. The current study suggests that wild medicinal plants should be adequately addressed for PTEs and other carcinogenic pollutants before their uses in the study area. Open dumping of mining waste should be banned and eco-friendly technology like organic amendments application should be used to mitigate PTEs in the study area.

Stainability and translucency of potassium aluminum sulfate applied computer-aided design and computer-aided manufacturing materials after coffee thermocycling.

OBJECTIVE: The purpose of this in vitro study was to evaluate the effect of potassium aluminum sulfate (alum) application on the stainability and translucency of computer-aided design and computer-aided manufacturing (CAD-CAM) materials after coffee thermocycling (CTC). MATERIALS AND METHODS: Disk-shaped specimens (Ø10 × 1 mm; N = 200) were fabricated by using additively (Crowntec [CT] and Varseo Smile Crown Plus [VS]) and subtractively manufactured (Brilliant Crios [RCR], CEREC Block [FC], and Vita Enamic [VE]) CAD-CAM materials and polished. All specimens were randomly divided into two groups as alum applied and control (n = 10). All specimens were then subjected to CTC (10,000 cycles at 5-55°C) and color coordinates were measured at each time interval. Color differences (ΔE00 ) and relative translucency parameters (RTPs) were calculated and the data were statistically analyzed (a = 0.05). RESULTS: Among tested time intervals, alum applied specimens had their lowest ΔE00 after alum application (p ≤ 0.006), except for FC (p = 0.177). In addition, alum applied RCR had lower ΔE00 values than its control specimens (p = 0.029). Alum applied specimens had their lowest RTP after CTC (p < 0.001) and alum application decreased the RTP of CT (p = 0.010). CTC reduced the RTP of all materials in control groups (p < 0.001). Alum applied CT had higher RTP than its control specimens (p = 0.049). CONCLUSIONS: Alum application's effect on color change varied depending on the material and alum mostly resulted in clinically acceptable changes in translucency. CTC led to unacceptable color and translucency changes based on previously reported threshold values. CLINICAL SIGNIFICANCE: Optical properties of CAD-CAM materials and the sustainability of these properties over time is critical for longevity. Alum may improve the color stability of reinforced composite resin when subjected to long-term coffee consumption.

Microhardness and Gloss of a New CAD/CAM Hybrid Material Following Accelerated Aging and Coffee Immersion.

PURPOSE: To evaluate and compare the effect of accelerated aging and coffee immersion on the microhardness and gloss of a new computer-aided design and computer-aided manufacturing (CAD/CAM) hybrid material (Crystal Ultra) to those of contemporary restorative materials. MATERIALS AND METHODS: A total of 160 specimens (12 × 14 × 1 mm ± 0.05 mm) were obtained from IPS e.max (IPS), VITA Enamic (VE), Crystal Ultra (CU), Lava Ultimate (LU), and CeraSmart (CS) high-translucency CAD/CAM blocks. The Vickers microhardness and gloss of the specimens were determined after thermocycling and coffee immersion. Data analysis was performed using SPSS (α = .05). RESULTS: IPS and CS specimens exhibited the highest (572.66 ± 11.30) and lowest (61.92 ± 3.91) microhardness, respectively. The highest gloss was observed with IPS specimens (3.31 ± 0.32), and LU specimens showed the lowest gloss (2.33 ± 0.06). A significant difference in gloss was observed between the materials at all measurement intervals (P < .01), except at T0 (P = .43). IPS specimens showed no significant changes in either group at any measurement interval. CONCLUSIONS: The microhardness and gloss of the new CU material were comparable to those of the tested contemporary hybrid restorative materials. Glass-ceramic showed superior hardness and gloss compared to hybrid restorative materials. Accelerated aging with thermocycling and staining significantly affected the microhardness and gloss of all tested CAD/CAM materials.

The loss of resin cement adhesion to ceramic influences the fatigue behavior of bonded lithium disilicate restorations.

When partial and/or non-retentive preparation, such as those for occlusal veneers, is indicated, a proper and stable adhesion is essential. Therefore, the aim of this in vitro study was to evaluate the effect of loss of adhesion in different regions of the bonding interface on the fatigue behavior of simplified lithium disilicate restorations. For this, lithium disilicate (IPS e.max CAD) discs (1 mm thick and Ø = 10 mm) were fabricated, polished with #400-, #600-, #1200-grit silicon carbide (SiC) papers, and crystallized. As substrate, fiber-reinforced resin epoxy discs (2.5 mm thick and Ø = 10 mm) were fabricated and polished with #600-grit SiC paper. The ceramic bonding surface was treated with 5% hydrofluoric acid and a silane-containing primer (Monobond N), while the substrate was etched with 10% hydrofluoric acid followed by the application of the bonding system primers (Primer A + B). A lacquer (nail polish) was used to simulate the loss of adhesion in specific areas according to the study design to compose the testing groups: bonded (control; did not received nail polish application); - non-bonded (loss of adhesion in the whole specimen area); - margin (loss of adhesion in the ceramic margin); - center (loss of adhesion in the ceramic central area). The adhesive area of partially bonded groups was 50% of the adhesive surface. Then, the discs (n = 12) were bonded to the respective substrate using a resin cement (Multilink N), light-cured, water-stored for 90 days, and subjected to thermocycling (25,000 cycles, 5° to 55 °C) before testing. A cyclic fatigue test was run (20 Hz, initial load of 200 N for 5000 cycles, 50 N step size for 10,000 cycles each until specimen failure), and the fatigue failure load and number of cycles for failure were recorded. As complementary analysis, finite element analysis (FEA) and scanning electron microscopy analysis were performed. Kaplan-Meier log-rank (Mantel-Cox) was conducted for survival analysis. The results showed that as the loss of adhesion reaches the central area, the worse is the fatigue behavior and the higher is the stress peak concentration in the ceramic bonding surface. The bonded specimens presented better fatigue behavior and stress distribution compared to the others. In conclusion in a non-retentive preparation situation, proper adhesion is a must for the restoration fatigue behavior even after aging; while the loss of adhesion reaches central areas the mechanical functioning is compromised.

Advanced lithium disilicate: A comparative evaluation of translucency and fatigue failure load to other ceramics for monolithic restorations.

The aim of this in vitro study was to evaluate the surface roughness, translucency, fatigue failure load (FFL), and number of cycles for fatigue failure (CFF) of a recently released lithia-based material called advanced lithium disilicate and three other ceramics indicated for monolithic restorations. First, ALD (advanced lithium disilicate, CEREC Tessera, Dentsply Sirona), LD (lithium disilicate, IPS e. max CAD, Ivoclar), LS (lithium silicate-disilicate, Suprinity, Vita Zahnfabrik), and 4Y-PSZ (Yttria-stabilized zirconia, IPS e.max ZirCAD MT, Ivoclar) discs (n = 15, Ø = 10 mm and thickness = 1.0 mm) were fabricated from CAD/CAM blocks/discs, A2 shade. The discs were sintered/crystallized and subsequently analyzed by a rugosimeter (Mitutoyo SJ-410) to determine Ra and Rz surface roughness parameters. Next, they were evaluated to determine the translucency parameter (TP) using a bench-top spectrophotometer (SP60, EX-Rite). The discs were subsequently cemented to glass fiber epoxy resin discs, and the specimens were tested under cyclic loading (Step-test), immersed in distilled water at a frequency of 20 Hz, with an initial cyclic load of 200 N for 5,000 cycles and increments of 50 N every 10,000 cycles until failure. Fatigue failure load (FFL) and number of cycles for fatigue failure (CFF) were recorded for subsequent Kaplan Meier analysis, with post-hoc Mantel-Cox and Weibull analysis (α = 0.05). Complementary fractographic, topographic and energy dispersive spectroscopy analyses (EDS) were performed. 4Y-PSZ showed higher survival (p < 0.05), with higher FFL and CFF (1077 N; 180,333 cycles), followed by LD (980 N; 161,000 cycles), LS (937 N; 152,333 cycles) and ALD (910 N; 147,000 cycles). No differences were observed between the tested groups regarding Weibull modulus. ALD presented TP (28.14) equal to DL (28.27) and higher than LS (25.51). All lithia-based materials had higher translucency than 4Y-PSZ (TP = 8.62) (p < 0.05). ALD appears to have a similar elemental composition to LD and LSD for oxygen and silicon. ALD and LSD have a similar zirconium content. Fractures originated on the cemented surface of the ceramic discs. Lithia-based ceramics showed lower surface roughness, with ALD (Ra = 0.04 µm; Rz = 0.66 µm) showing the lowest values (p < 0.05). Despite showing lower FFL when compared to LD and 4Y-PSZ, ALD has compatible translucency and mechanical fatigue performance with its indication for fabricating monolithic, anterior and posterior adhesively cemented single-unit restorations. However, further studies are needed to substantiate its clinical performance.

Influence of coloring techniques on the surface characteristics and color stability of a monolithic zirconia ceramic.

STATEMENT OF PROBLEM: The color of monolithic zirconia restorations is obtained by presintering or postsintering coloring techniques. However, studies on the differences in surface characteristics and their influence on color stability are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the influence of shading and staining techniques for a zirconia ceramic on the surface characteristics and colorimetric parameters (color difference, translucency, and whiteness index) after exposure to coffee or red wine and then polishing. MATERIAL AND METHODS: Ceramic disks (N=30; Ø10×1mm) were allocated into 3 groups: preshaded-shaded by the manufacturer (IPS e.max ZirCAD MT, shade A2); manually shaded-unshaded zirconia (IPS e.max ZirCAD MT, bleaching shade-BL) colored by the brushing technique, before sintering; stained-unshaded zirconia (IPS e.max ZirCAD MT BL) colored by the staining technique, after sintering. Spectrophotometric color assessments ensured the same initial perceived color (Vita Classical A2) for specimens included in the study (∆E00<1.77 acceptability threshold). Surface characteristics were assessed by scanning electron microscopy and atomic force microscopy. The specimens were immersed in coffee (n=5) or red wine (n=5) for 12 and 24 days and subsequently polished. The data were statistically and descriptively analyzed for color differences (∆E00), translucency parameters (TP00), and whiteness indexes for dentistry (WID), considering acceptability and perceptibility thresholds. RESULTS: The shaded groups found an irregular ceramic surface with uniformly sized zirconia crystals. The stained group found a glass-covered smoother surface. Significant alterations in color parameters (∆E00, TP00, WID) were observed with immersion in pigmenting beverages (P<.001) both after 12 days, and after 24 days. The shaded specimens had greater color alterations after immersion but benefited from the polishing procedure, which reduced color differences below an acceptable threshold in comparison with the baseline. Stained specimens had lower color alterations after immersion, but the polishing protocol was detrimental as it whitened the ceramic by subsurface exposure. CONCLUSIONS: The coloring technique influences the surface characteristics of zirconia ceramic and also the color parameters after exposure to colored beverages and polishing.

Influence of resin cement on color stability when luting lithium disilicate and zirconia restorations.

AIM: To evaluate the influence of resin cement on the color stability of lithium disilicate and zirconia restorations immersed in coffee after aging. MATERIALS AND METHODS: Eighty maxillary premolars were classified into eight groups (n = 10) based on restorative material type (lithium disilicate or zirconia), resin cement type (G-CEM LinkForce; GC Corporation or Panavia SA Cement Plus Automix; Kuraray Noritake Dental), and preheating temperature (25°C or 54°C). Following tooth preparation, each restoration was bonded to its corresponding substrate. Using a reflectance spectrophotometer, Commission Internationale de l'Éclairage (CIE) tristimulus values were detected and calculated (D65 standard illumination, 10-degree observer angle). All specimens were aged (240,000 load cycles followed by 10,000 thermal cycles), then immersed in coffee (18 h). Following that, the second measurements of the color coordinates were determined. The total color differences were measured, and the data were statistically analyzed (α = 0.05). RESULTS: The temperature had a significant effect on ΔL΄ (P < 0.001), ΔC΄ (P < 0.001), and ΔH΄ (P < 0.001). The lithium disilicate restorations were more color stable than the zirconia restorations. Also, there was a significant difference (P = 0.047) between the LinkForce (2.28 ± 0.48) and Panavia SA (2.15 ± 0.46) cement. The restorations cemented at a temperature of 54°C (1.76 ± 0.11) showed significant color differences (P < 0.001) compared with those cemented at a temperature of 25°C (2.67 ± 0.15). A three-way analysis of variance (ANOVA) test revealed that the interaction between the ceramic material, cement type, and temperature had no statistically significant effect (P = 0.611) on the color stability of the ceramic restorations. CONCLUSIONS: Cement type has a significant effect on the color stability of lithium disilicate and zirconia restorations. Cement at a temperature of up to 54°C enhances the color stability of lithium disilicate and zirconia restorations.

Failure behavior of zirconia crowns subjected to air abrasion with different particle sizes.

This study aimed to investigate the failure behavior of 3 mol.% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) prosthetic crowns air-abraded with aluminum oxide (AO) particles of different sizes. Ninety ceramic premolar crowns were produced with 3Y-TZP frameworks veneered with porcelain. Crowns were randomly divided into three groups, according to the size of the air abrasion AO particles (n = 30): (GC) untreated (control); (G53) 53 µm; (G125) 125 µm. Air abrasion was performed with 0.25 mpa pressure, 10-mm distance, for 10 s. Crowns were adhesively cemented to dentin analog abutments. Specimens were loaded in compression to failure, in 37oC distilled water, using a universal testing machine (n = 30). Fractographic analysis was performed using a stereomicroscope and SEM. The roughness of the crown's inner surface was evaluated using an optical profilometer (n = 10). Fracture load data were statistically analyzed with Weibull analysis and roughness data with Kruskal-Wallis (α = 0.05). GC had the lowest characteristic fracture load (L0), while G53 and G125 had higher and statistically similar L0 values. The Weibull modulus (m) was similar among groups. The failure modes observed were catastrophic failure and porcelain chipping. There were no differences between the roughness parameters for the experimental groups (p > 0.05). The size of the AO particles did not affect the fracture load and failure mode of 3Y-TZP crowns. Air abrasion with 53 µm and 125 µm particles resulted in a higher fracture load of ceramic crowns than the untreated group while maintaining their reliability and surface characteristics.

Comparison of the Degree of Staining of Computer-Aided Design-Computer-Aided Manufacture (CAD-CAM) Ceramic Veneers by Green Tea, Coffee, and Coca-Cola Using a Digital Spectrophotometer.

BACKGROUND The majority of dental professionals currently recognize lithium disilicate E-max ceramic veneers as a the most widely used, conservative, and effective cosmetic materials in dentistry. This study aimed to compare the degree of surface changes - roughness (Ra), depth (Rz), and mean color changes (ΔE00) - of computer-aided design-computer-aided manufactured (CAD/CAM) ceramic veneers materials of varying thicknesses caused by staining by green tea, coffee, and Coca-Cola using digital spectrophotometer. MATERIAL AND METHODS This study was conducted at King Khalid University, College of Dentistry. Lithium disilicate glass ceramic (LDGC) material was used to create 60 rectangular slices using the CAD/CAM system. The material thickness and the type of beverage were measured. The specimens were immersed in beverages according to the manufacturer's instructions. Specimen description and tomography were completed with a 3D noncontact surface metrology using interferometry. The "VITA Easy-Shade" spectrophotometer was used to measure ΔE00. It was recorded after 2 weeks for different material thicknesses after immersing samples in green tea, coffee, and Coca-Cola staining materials.f RESULTS Significant changes in ceramic thickness were found in Ra and Rz of 0.07 and 1.00 mm after 14 days of staining. Coca-Cola showed a significant difference in Ra and Rz with 1.00 mm thickness measurement compared to the 0.07 mm group with ≤ of 0.05, which was considered statistically significant. Highest ΔE00 were recorded among samples stained by Coca-Cola, followed by coffee, for both thicknesses. CONCLUSIONS Those findings support previous studies using spectrophotometric analysis of staining of CAD-CAM ceramic veneers that Coca-Cola followed by coffee resulted in the greatest color ΔE00 change.

Choosing transcatheter aortic valve replacement in porcelain aorta: outcomes versus surgical replacement.

OBJECTIVES: Porcelain aorta complicates aortic valve replacement and is an indication for transcatheter approaches. No study has compared surgical and transcatheter valve replacement in the setting of porcelain aorta. We characterize porcelain aorta patients undergoing aortic valve replacement and the association of aortic calcification and outcomes. METHODS: Patients undergoing aortic valve replacement with porcelain aorta were identified. Aortic calcium volume was determined using 3D computed tomography thresholding techniques. Propensity scoring was performed to assess the effect of surgical versus transcatheter approaches. Risk factors for composite major hospital complications (death, stroke and dialysis) were identified using random forest machine learning. RESULTS: From January 2006 to January 2015, 164 patients with porcelain aorta underwent aortic valve replacement [105 (64%) surgical replacement, 59 (36%) transcatheter replacement]. Propensity scoring matched 29 pairs (49% of transcatheter patients). Before matching, 5-year survival was 41% [(43% surgical, 35% transcatheter, P(log-rank) = 0.9]. After matching, mortality for surgical versus transcatheter replacement was 3.4% (n = 1) vs 10% (n = 3), stroke 14% (n = 4) vs 3.4% (n = 1) and dialysis 6.9% (n = 2) versus 11% (n = 3). Matched 5-year survival was 40% after surgical replacement and 29% after transcatheter replacement [P(log-rank) = 0.4]. Total aortic calcium volume was greater in transcatheter than surgical patients [18 (8.0) vs 17 (7.7) ml] and was associated with more major hospital complications after either approach. CONCLUSIONS: Surgical and transcatheter approaches are complementary options for aortic stenosis with porcelain aorta. Surgical valve replacement remains an effective treatment for patients requiring concomitant procedures. Quantifying aortic calcium volume is a helpful risk predictor in all patients with porcelain aorta.

Wear pattern-associated color stability of prefabricated composite veneers versus ceramic veneers.

PURPOSE: To evaluate the effect of different surface wear patterns on the discoloration tendency of two different prefabricated composite veneers and lithium disilicate ceramic veneers. MATERIALS AND METHODS: Discoloration tendency of two prefabricated composite resin veneers (Visalys Veneer Chairside (VIS) and Componeer (COM)) were compared to lithium disilicate veneers (IPS) in vitro. For each material, n = 60 samples were allocated to different test groups, and therefore each n = 10 specimens per group went through different wear tests. Mechanical abrasion tests were conducted using a toothbrush simulator, while erosive effects were carried out by citric acid (pH 1.57). A combination of abrasion and erosion tests was conducted as well. Four groups of wear tests were implemented: (1) abrasion, (2) abrasion followed by erosion, (3) erosion, and (4) erosion followed by abrasion. Another group was stored in distilled water as the control and one group was stained without a prior wear test. The staining solution was made from a coffee-tobacco brew. Specimens were stored in the coffee-tobacco solution for 21 days. Color measurements were performed with VITA Easyshade. To evaluate intramaterial discoloration, one half of every specimen was protected with foil. After storage in the staining solution, the first measurement was carried out on the 'protected' (untreated) surface, followed by a second measurement on the 'processed' (treated) discolored surface. Euclidean distance (ΔE) of discoloration was calculated according to the CIE-L*C*h* system. Data were analyzed with ANOVA followed by Games-Howell post hoc test and paired t-test (α = 0.05). RESULTS: Highest changes in ΔE were found in COM after 'abrasion' (ΔE -2.55) and 'erosion followed by abrasion' (ΔE -1.41). The discoloration tendency of VIS was affected by all wear tests, but changes were below the perceptive threshold (ΔE -0.19-0.32). Only abrasion followed by erosion affected the discoloration of IPS significantly, but findings were below the perceptive threshold, as well (ΔE -0.09). CONCLUSIONS: Prefabricated composite resin veneers revealed a low level of discoloration tendency after different wear tests. Nevertheless, in most cases the lowest discoloration tendency was found in specimens made from lithium disilicate.

Effect of dimensional variations on the manufacturing process and the 3D shrinkage ratio of stereolithographic dental alumina ceramics.

The purpose of the present study was to evaluate the influence of height and length variations of alumina ceramics manufactured by stereolithography on deformations caused by the manufacturing process and on the 3D shrinkage ratio to control the final dimensions and improve the adaptation of stereolithographic ceramic dental prostheses. Two different U-shaped models were designed with variable heights or lengths. The specimens were manufactured by stereolithography and were scanned using a microtomographic device before and after the heat treatment. Dimensional variations were measured using inspection software. The number and surface of layers of alumina ceramic influenced the reliability of the stereolithography manufacturing but did not influence the 3D shrinkage ratio. The larger the layer surface, the larger the deformation of the ceramic. Dental ceramics manufactured by stereolithography with smallest layer surface are the most reliable. This helps in the selection of the build orientation.

Strength and flexibility of lithium disilicate bonded to polyetherketoneketone.

STATEMENT OF PROBLEM: Polyetherketoneketone (PEKK) is a high-performance polymer gaining popularity in dentistry for the fabrication of crowns, fixed partial dentures, removable partial denture frameworks, and frameworks for implant-supported fixed complete dentures. Despite a lack of performance data, lithium disilicate crowns have been bonded to retentive elements in PEKK frameworks. PURPOSE: The purpose of this in vitro study was to compare the bond strengths and flexibility of lithium disilicate to PEKK or zirconia. MATERIAL AND METHODS: Forty-five PEKK, 15 zirconia, and 60 lithium disilicate beam-shaped specimens (12.5×2×2 mm) were fabricated. The ends of the PEKK beams were subjected to 3 different surface treatments before the application and light polymerization of a primer: 50-µm aluminum oxide airborne-particle abrasion, nonthermal air plasma, and argon-oxygen plasma. The zirconia specimen bonding surfaces were prepared with 50-µm aluminum oxide airborne-particle abrasion and the application of primer. Lithium disilicate specimens were etched with 4.5% hydrofluoric acid, and primer was applied. The lithium disilicate specimens were luted with an adhesive resin cement to the PEKK and zirconia specimens by using light-activated and chemically activated polymerization. Fifteen monolithic specimens of PEKK, lithium disilicate, and zirconia (25×2×2 mm) were also fabricated. All specimens were incubated overnight in 100% humidity before testing. Bonded and monolithic specimens were loaded in a universal testing machine, and 4-point bend tests were conducted until failure (n=15). The flexural modulus and strength were calculated and statistically analyzed with 1-way analysis of variance and Student-Newman-Keuls post hoc tests (α=.05). RESULTS: All bonded specimens failed at the adhesive interface. The zirconia-lithium disilicate bond strength was approximately twice that of the strongest group of PEKK (airborne-particle abrasion group) bonded to lithium disilicate (42 ±12 MPa and 24 ±13 MPa, respectively) and was approximately 9 times more rigid (71 ±19 GPa and 8 ±2 GPa, respectively). Monolithic PEKK fractured at 238 ±22 MPa, monolithic zirconia at 771 ±128 MPa, and monolithic lithium disilicate at 173 ±26 MPa. Monolithic PEKK was approximately 30 times more flexible than monolithic zirconia (6 ±1 GPa and 178 ±16 GPa, respectively). All values were statistically significantly different (P<.05), except for the bond strength between lithium disilicate and PEKK treated with airborne-particle abrasion and nonthermal air plasma and the flexural moduli of PEKK to lithium disilicate. CONCLUSIONS: Bond strength between PEKK and lithium disilicate was significantly weaker than that between zirconia and lithium disilicate. Monolithic PEKK was significantly more flexible than monolithic zirconia.

Translucency, color stability, and biaxial flexural strength of advanced lithium disilicate ceramic after coffee thermocycling.

OBJECTIVE: To compare the color stability, translucency, and biaxial flexural strength (BFS) of differently glazed advanced lithium disilicate (ALDS) with those of lithium disilicate (LDS) and zirconia-reinforced lithium silicate (ZLS) after coffee thermocycling. MATERIALS AND METHODS: Forty disk-shaped specimens were prepared from three lithium silicate based materials (CEREC Tessera, ALDS; IPS e.max CAD, LDS; Vita Suprinity, ZLS). ALDS specimens were divided into two subgroups according to glazing procedures (reduced glaze duration, ALDS-S and normal glaze duration, ALDS-N), while LDS and ZLS specimens were crystallized and glazed. Color coordinate measurements were performed before and after coffee thermocycling. Color differences (ΔE00 ) and relative translucency parameters (RTP) were calculated. Specimens were then subjected to BFS test. Statistical analysis was performed by using 1- (ΔE00 and BFS) and 2-way (RTP) ANOVA tests (α = 0.05). RESULTS: ΔE00 values of tested materials were similar (df = 3, F = 0.150, p = 0.929). Two-way ANOVA showed the significant effect of material type, coffee thermocycling, and the interaction between these parameters on RTP values (p < 0.001). Both before and after thermocycling, LDS had the highest (p ≤ 0.001) and ZLS had the lowest (p < 0.001) RTP values, while ALDS-N had higher RTP than ALDS-S (p ≤ 0.001). Among tested materials, only LDS had similar RTP values before and after thermocycling (p = 0.865) as the other materials had lower RTP values after thermocycling (p < 0.001). ALDS-N had higher BFS values than ALDS-S (p = 0.005), while LDS had similar values to ALDS specimens (p ≥ 0.201). ZLS had the highest BFS (p ≤ 0.007). CONCLUSIONS: ALDS had comparable values to those of other materials. However, reduced glazing duration resulted in decreased translucency and BFS of ALDS. CLINICAL SIGNIFICANCE: ALDS may be an appropriate restorative material for those patients with increased coffee consumption considering its color stability and ability to maintain translucency, particularly when glazed by using a conventional porcelain furnace.

Polyphenols-Rich Extract of Calotropis procera Alone and in Combination with Trichoderma Culture Filtrate for Biocontrol of Cantaloupe Wilt and Root Rot Fungi.

Fungal diseases have always been a major problem for cantaloupe crops; however, synthetic fungicides are hazardous to humans and the environment. Consequently, a feasible alternative to fungicides without side effects could be by using bio agents and naturally occurring plants with antibacterial potential. This study has achieved a novel procedure for managing wilt and root rot diseases by potentially using Trichoderma sp. culture filtrates in consortium with plant extract of Calotropis procera, Rhizoctonia solani, Fusarium oxysporum, and Pythium ultimum, which were isolated from infected cantaloupe roots with identified root rot symptoms. The antagonistic activity of four Trichoderma isolates and analysis of antibiotics and filtrate enzymes of the most active Trichoderma isolate were determined as well as phytochemical analysis of C. procera plant extract using HPLC-UV. The obtained results showed that all Trichoderma isolates considerably lowered the radial growth of P. ultimum, R. solani, and F. oxysporum in varying degrees. The scanning electron micrographs illustrate the mycoparasitic nature of Trichoderma sp. on F. oxysporum. The phytochemical analysis of C. procera indicated that phenolic contents were the major compounds found in extracts, such as vanillin (46.79%), chlorogenic acid (30.24%), gallic acid (8.06%), and daidzein (3.45%) but including only a low amount of the flavonoid compounds rutin, naringenin, and hesperetin. The Pot experiment's findings showed that cantaloupe was best protected against wilting and root rot diseases when it was treated with both Trichoderma sp. culture filtrates (10%) and C. procera extract of (15 mg/mL), both alone and in combination. This study demonstrates that the application of bio agent Trichoderma spp. filtrate with C. procera phenol extract appears useful for controlling wilting and root rot disease in cantaloupe. This innovative approach could be used as an alternative to chemical fungicide for the control of wilting and rot root diseases.

EFFECT OF SURFACE TREATMENT PROTOCOLS OF ZIRCONIUM DIOXIDE MULTILAYER RESTORATIONS ON FUNCTIONAL PROPERTIES OF THE HUMAN ORAL MUCOSA STROMAL CELLS.

Aim - to study the effect of protocols of surface treatment of zirconium dioxide multilayer restorations on the functional properties of stromal cells of the human oral mucosa using molecular biological methods. For all experiments, identical standardized specimens of different types of zirconia with a diameter of 10 mm and a height of 1 mm were used. These types included Katana (Kuraray Noritake Dental, Tokyo, Japan) HTML (control) UTML, STML and ZirCAD Prime (Ivoclar Vivadent). DMEM/F12 growth medium (Paneco, Russian Federation) with addition of fetal calf serum (Gibco, USA) up to 10% and penicillin-streptomycin (Paneco, Russian Federation) up to 1% was used in the experiment. Cells were detached from the culture substrate with trypsin-EDTA solution (Paneco, RF) and their number and viability were assessed using an automatic counter TC-20 (Bio-Rad, USA). For repopulation, samples were transferred into wells of a 96-well culture plate (1 sample in 1 well) and cell suspension was layered at the rate of 12.5 thousand or 25 thousand live cells per well. After 48 hours, the cytotoxic properties of the tested samples were evaluated in vitro. According to the results of MTT test we can conclude that samples of ZirCad Prime and Katana UTML groups do not show cytotoxic properties (score "0" on the cytotoxicity scale according to GOST R ISO 10993-5-2009 "National Standard of the Russian Federation. Medical devices. Evaluation of biological effect of medical devices. Part 5. Studies on cytotoxicity: in vitro methods"). The samples of Katana STML group samples were slightly reduced compared to the control (about 12%), nevertheless, these samples can also be considered non-cytotoxic. Analyzing the direct contact with the material in all samples, a good occupancy of the material by cells was observed, in particular, the polished surface prevailed over the glazed one, however, this difference is not statistically significant. Analysis of human oral stromal cells to zirconium dioxide showed no statistically significant effect of different surface treatment protocols. However, the number of fibroblasts prevailed on the polished surface.