Phosphorus recovery from aqueous solutions using Bioclastic Granules (Lithothamnium calcareum).

Against the growing world demand for food and the possibility of recovering some nutrients, this work focused on the evaluation of the use of Bioclastic Granules (BG) from the algae Lithothamnium calcareum as sorbent material for the removal/recovery of phosphorus from aqueous solutions. The main variables that affect the sorption process, pH, initial concentration of phosphate, and GB, as well as the contact time, were evaluated. The effect of pH was very significant, obtaining the best results of PO43- removal at pH 5. In the coarser granulometric fractions (+ 106 - 150 and + 210 - 300 µm), the best removals were observed (around 75%). Regarding the initial PO43- concentration in the solutions, the highest removal (in the range of 74 to 78%) was observed in the lowest concentrations (5 to 70 mg L-1) and the best uptake (10 to 14 mg g-1) at higher concentrations (200 to 420 mg L-1). The PO43- sorption data fitted the Freundlich model well, with kF of 1.35 L mg-1 and n of 2.43. A qmax of 14.35 mg g-1 was obtained using the Langmuir model. Regarding the sorption data over time, a better fit to the pseudo-first-order kinetic model was observed, obtaining a calculated qeq of 6.56 mg g-1 and a k1 of 0.0073 min-1. The incorporation of PO43- ions in the GB structure was confirmed through the characterization results before and after the sorption experiments using X-ray fluorescence (FRX) and scanning electron microscopy (SEM) techniques.

Combining topical dermal infused exosomes with injected calcium hydroxylapatite for enhanced tissue biostimulation.

BACKGROUND: Exosome research continues to flourish. Subsequent knowledge surrounding indications, dose-response, safety, efficacy, and the ability to combine exosome treatment as a "skin primer"-for biostimulation modalities such as calcium hydroxylapatite (CaHA), platelet-rich plasma (PRP), and platelet-rich fibrin matrix (PRFM) is growing rapidly. The objective of this study was to develop safe, reproducible methods of improving topical exosome absorption to enhance the quality of skin either by themselves, or in combination with injectable CaHA. METHODS: Under IRB Approval (International Cell Surgical Society: ICSS-2022-007), 40 patients were enrolled in this study. Twenty patients underwent facial biostimulatory dermal infusion alone, to determine if this method allowed adequate exosome absorption. Five patients underwent facial biostimulatory infusion followed immediately by Dilute CaHA injection (1:1 dilution) to the face. Five patients underwent exosome biostimulatory dermal infusion followed immediately by hyperdilute CaHA (dilution 1:4) injection to the neck. Five patients underwent Facial Dilute CaHA injection (1:1 dilution) alone, without dermal infusion. Five patients underwent neck hyperdilute CaHA injection (1:4 dilution) alone, without dermal infusion. All patients had pretreatment Quantificare 3-D photo-documentation and skin analysis (Quantificare, France). In all patients, the skin was first cleansed with a gentle glycolic acid facial wash (Gregory MD). To induce a "homing inflammatory environment" for the exosomes, sea salt exfoliation was performed (SaltFacial®, SaltMed, Cardiff, CA). A nitric oxide-generating serum (N101 Pneuma Nitric Oxide, Austin, TX) was then applied to act as an enhanced vehicle for absorption. A 3 MHz ultrasound (SaltFacial®, SaltMed, Cardiff, CA) was then utilized to further deepen the absorption of the nitric oxide serum. A topical emulsion containing equal volumes (1.0 cc containing 1 million) of exosomes (Kimera Labs, Miramar, FL), 25 units of botulinum toxin (Xeomin, Merz Aesthetics, Raleigh, NC) and hyaluronic acid (Belatero, Merz Aesthetics, Raleigh, NC) was mixed via back-and-forth propulsion in a 3-cc syringe. When adequately mixed, the emulsion was then applied to the treatment areas. The cavitating ultrasound was then used to aid in the absorption of the emulsion. The patients were then treated with high-intensity LED therapy (SaltFacial®, SaltMed, Cardiff, CA), utilizing the collagen restoration preset program of combination red (660 nm) near-infrared (930 nm) wavelength for 20 min. Post-treatment Quantificare analysis was performed at 15 and 30 days after treatment. RESULTS: Without exception, all dermal infusion alone and CaHA injection alone patients showed an improvement in the tone, quality, and texture of their skin. Quantificare results showed consistent improvement in wrinkles, pores, skin evenness, improved vascularity, and a reduction in oiliness and unwanted pigment. When employed as a skin primer prior to injections (CaHA), enhanced and more rapid results were seen. CONCLUSIONS: Biostimulatory dermal infusion can be achieved utilizing topical placental mesenchymal stem cell-derived exosomes. These exosomes can be used alone, or mixed with ancillary ingredients such as botulinum toxin, hyaluronic acid dermal filler, and CaHA to customize and personalize treatments based upon individual patient needs. Topical absorption is enhanced with sea salt exfoliation, a topical nitric oxide-generating serum, and 3 MHz cavitating ultrasound. Post-absorption activity is enhanced with high-intensity LED treatment. The addition of CaHA injections after the topical exosome "priming of the skin" yielded enhanced skin quality faster than exosomes or CaHA alone.

Self-assembled Patterns Formed in Evaporating Droplets to Analyze Bi-component Homeopathic Preparations in the Low Dilution Range.

BACKGROUND: Homeopathic complex remedies, composed of several homeopathic medicines in the low potency range, are frequently used in the treatment of a number of common disorders. At the same time, they represent an almost unexplored area of research. Are complex remedies just additive mixtures of the components, or are there interactions between the latter leading to new properties of the complex? METHODS: In the present study, we analyzed as an example the simple bi-component complex, Luffa 4x - Mercurius bijodatus 9x, by means of patterns from evaporated droplets and tested what influences the complex's single compounds have upon the patterns and if there are any interactions. For this purpose, we compared in a series of five experiments patterns from evaporated droplets of the complex, Luffa 4x - Mercurius bijodatus 9x, and three comparison samples in which one or both of the complex's compounds were replaced by potentized solute. The patterns were photographed and evaluated for their gray-level distribution and texture using the software ImageJ. The experimental set-up's stability was tested by means of systematic control experiments. RESULTS: We found that Mercurius bijodatus 9x significantly influenced the patterns of Luffa 4x, increasing their homogeneity; at the same time, the patterns of Mercurius bijodatus 9x combined with solvent were more heterogeneous than those obtained from a control consisting of two pure solvents. CONCLUSION: In this phenomenological assay, the complex Luffa 4x - Mercurius bijodatus 9x does not correspond to a simple addition of the components. The exact nature of the underlying interaction needs to be elucidated in further investigations.

An effective uranium removal using diversified synthesized cross-linked chitosan bis-aldehyde Schiff base derivatives from aqueous solutions.

Three new cross-linked chitosan derivatives were yielded through intensification of chitosan with diverse types of bis-aldehydes. The prepared cross-linked chitosan was characterized by FTIR, 1H NMR, XRD, and TGA techniques. TGA indicated an improvement in thermal stability of the cross-linked chitosan compared with pure chitosan. Batch adsorption experiments showed that the three novel cross-linked chitosan bis-aldehyde derivatives possessed good adsorption capacity against U(VI) in the order of BFPA > BFB > BODB (adsorption capacity of the three adsorbents for U(VI) reaches 142, 124, and 114 mg/g respectively) and the adsorption isotherm and kinetic were well described by the Langmuir and the pseudo-second-order kinetic model, respectively. In addition, the prepared cross-linked chitosan bis-aldehyde derivatives were examined as U(VI) catcher from waste solutions.

Effect of different molecular characteristics on the lubrication behavior of polysaccharide solutions.

Polysaccharides strongly affect the sensorial properties of foods, which is partly related to the lubrication they provide. We investigated the lubrication performance of polysaccharides with different characteristics (i.e. molecular weight, conformation, stiffness, and charge density) to identify the most relevant structural features related to lubrication ability. The effect of viscosity was excluded using isoviscous systems. Conformation resulted to be a key factor in determining lubrication. Rigid rod-like polysaccharides (xanthan) showed higher lubricating capacity and better resistance to changes in pH and ionic strength compared to semi-flexible (pectin and carboxymethyl cellulose) and flexible polysaccharide (guar gum). The friction behavior of flexible polysaccharides was highly dependent on concentration and sliding speed, for which a model including parameters of friction, concentration, and speed was developed. The concentration-dependency of the lubrication was related to the shear-thinning behavior, and possible mechanisms to explain these differences in terms of molecular properties of the polysaccharides are proposed.

The effect of biopolymer-water interaction on relaxation phenomena in blackcurrant pectin solutions.

Pectin is commonly used food additive. Depends on the source of the acquisition, its properties may vary significantly, therefore pectin obtained from different sources may be used for various purposes. Little information can be found about the properties of blackcurrant pectin. Therefore, the aim of this study was to investigate blackcurrant pectin properties, with particular emphasis on biopolymer behaviour in aqueous solutions. Applied water extraction resulted in a water-soluble fraction of pectin with Mw = 115.75 kg·mol-1. Aqueous solutions of obtained polysaccharides was tested with various methods (membrane osmometry, DLS, NMR, viscosity tests) that allowed for a comprehensive description of biopolymer-biopolymer and biopolymer-water interactions in both, dilute and semidilute regime. Blackcurrant pectin exhibits behaviour characteristic for polyelectrolytes. The analysis of the obtained results shows that, despite its low molecular weight, obtained pectin has a highly branched structure, which influences strong intermolecular interactions in solutions.

Biosorption of uranium from aqueous solutions by Azolla sp. and Limnobium laevigatum.

The main goal of this study was to assess alternatives to the current challenges on environmental quality and circular economy. The former is here addressed by the treatment of radioactively contaminated solutions, and the latter by using abundant and low-cost biomass. In this paper, we examine the biosorption of hexavalent uranium (U(VI)) in a batch system using the macrophytes Limnobium laevigatum and Azolla sp. by three operational parameters: biomass dose, metal ion concentration, and contact time. Simulated solutions were firstly addressed with two biomasses, followed by studies with real liquid organic radioactive waste (LORW) with Azolla sp. The batch experiments were carried out by mixing 0.20 g biomass in 10 mL of the prepared solution or LORW. The total contact time employed for the determination of the equilibrium times was 240 min, and the initial U(VI) concentration was 0.63 mmol L-1. The equilibrium times were 15 min for L. laevigatum and 30 min for Azolla sp. respectively. A wide range of initial U(VI) concentrations (0.25-36 mmol L-1) was then used to assess the adsorption capacity of each macrophyte. Isotherm models validated the adsorption performance of the biosorption process. Azolla sp. presented a much higher U(VI) uptake (0.474 mmol g-1) compared to L. laevigatum (0.026 mmol g-1). When in contact with LORW, Azolla sp. removed much less uranium, indicating an adsorption capacity of 0.010 mmol g-1. In conclusion, both biomasses, especially Azolla sp., can be used in the treatment of uranium-contaminated solutions.

Structure and functionality of Rhamnogalacturonan I in the cell wall and in solution: A review.

Rhamnogalacturonan I (RG-I) belongs to the pectin family and is found in many plant cell wall types at different growth stages. It plays a significant role in cell wall and plant biomechanics and shows a gelling ability in solution. However, it has a significantly more complicated structure than smooth homogalacturonan (HG) and its variability due to plant source and physiological state contributes to the fact that RG-I's structure and function is still not so well known. Since functionality is a product of structure, we present a comprehensive review concerning the chemical structure and conformation of RG-I, its functions in plants and properties in solutions.

Novel adsorbent based on carbon-modified zirconia/spinel ferrite nanostructures: Evaluation for the removal of cobalt and europium radionuclides from aqueous solutions.

Herein, a novel adsorbent based on carbon-modified zirconia/spinel ferrite (C@ ZrO2/Mn0.5Mg0.25Zn0.25Fe2O4) nanostructures were chemically prepared to remove 60Co and 152+154Eu radionuclides from liquid media using batch experiments. The XRD pattern confirms the successful preparation of the C@ZrO2/MnMgZnFe2O4 composite. Also, SEM and TEM images confirmed that the composite owns a heterogeneous morphology in the nanoscale range. The optical band gap value of Mn0.5Mg0.25Zn0.25Fe2O4, ZrO2, and the composite samples was 1.45, 2.38, and 1.54 eV, respectively. Many parameters have been studied as the effect of time, solution pH, and initial ion concentration. The kinetics models for the removal process of 152+154Eu and 60Co radionuclides were studied. The second-order kinetic equation could describe the sorption kinetics for both radionuclides. The Langmuir monolayer capacity for 60Co was 82.51 mg/g and for 152+154Eu was 136.98 mg/g. The thermodynamic parameters such as free energy ΔGo, the enthalpy ΔHo, and the entropy ΔSo were calculated. The results indicated that the sorption process has endothermic nature for both two radionuclides onto C@ZrO2/MnMgZnFe2O4 composite.

Removal of nano-sized polystyrene plastic from aqueous solutions using untreated coffee grounds.

Nanoplastic (NP) pollution is an emerging global concern due to its adverse impact on aquatic ecosystems. Nevertheless, the removal of aqueous NPs from aquatic environments remains a significant challenge. This study aims to investigate whether polystyrene NP in aqueous solutions can be removed using coffee grounds. Due to the difficulty associated with directly measuring NP levels and monitoring the biosorption process, we used fluorescent-orange amine-modified polystyrene beads (fluo-NP, 100 nm) to evaluate the efficacy of the biosorption process. The factors including pH, coffee grounds concentration, initial fluo-NP concentration, and contact time were optimized on batch experiments. In addition, the isotherm and kinetic models were employed to clarify the adsorption behaviors and mechanisms. It was found that aqueous fluo-NP particles were effectively adsorbed onto the coffee grounds over a wide pH range (pH 2-12), with a coffee ground concentration of 25 g/L leading to the maximum adsorption efficiency (74%). The equilibrium adsorption capacity of the coffee grounds was 4 mg/g for a reaction time of 40 min. Coffee grounds demonstrated the highest removal efficiency when the initial fluo-NP concentration was 100-125 mg/L. The Dubinin-Radushkevich model and pseudo-second-order model described the adsorption isotherm and kinetics well, respectively, and the adsorption at high fluo-NP concentration range was favorable. Moreover, the results suggest that the mechanism lies in the electrostatic interactions and hydrogen bonding between surface functional groups of the coffee grounds and the fluo-NP particles. Given that there is an urgent need to remove NPs from aqueous systems, this study illustrates that it is possible to use coffee ground biowaste for this purpose.

Removal of Congo red dyes from aqueous solutions by porous γ-alumina nanoshells.

Porous alumina has been shown to be an excellent adsorbent for Congo Red (CR) dye. In this work, highly porous g-Al2O3 nanoshells were synthesized from alumina coated carbon black (CB) obtained from a new deposition technique and used for removal of CR dye from aqueous solutions. Adsorption experiments were conducted in a batch mode and a series of parameters were investigated, including contact time, initial dye concentrations, ionic strength and pH of the solutions. It was found that equilibrium for CR adsorption can be reached within 30 min, much faster than reported by other studies in the literature on similar adsorbents. It was also found that the adsorption capacity of Al2O3 nanoshells is 44.8 % higher than that of alumina/CB. The adsorption capacity of Al2O3 nanoshells was more favorable at lower pH, and the optimal adsorption ability was achieved at pH 4.0 with a removal efficiency at 98.6 %. The Al2O3 nanoshells have a maximum adsorption capacity of 370.4 mg g-1 (25 °C; pH 7; no salt added), better than or comparable to those reported in the literature. A pseudo-second-order kinetics model can best fit the kinetics of CR adsorption, which follows the Langmuir isotherm. The high adsorption capacity is attributed to the strong hydrogen-bonding interactions between the anionic dye and Al2O3 nanoshells surface as well as to the electrostatic interactions between CR dye and the Al2O3 nanoshells.

Shedding light on curcumin stability.

The stability of molecular curcumin (purcumin, 1a) in solution is strongly light-dependent. Under laboratory artificial light, a relative stability is observed only at neutral pH, while more intense light and/or solar light can trigger degradation via a combination of hydrolytic and oxidative fragmentation of the heptadiendione moiety. Minor curcuminoids in commercial curcumin (purcuminoids) can improve the stability of molecular curcumin, but only under conditions of low irradiation. While confirming earlier observations alerting to the instability of purcumin, our results provide new rationales for unexplained differences between previous studies, question the biological relevance of a non-enzymatic degradation for the bioactivity profiles that have been reported for purcumin, and highlight the need of a better characterization of the degradation of purcuminoids under visible light irradiation.

From coffee stains to uniform deposits: Significance of the contact-line mobility.

HYPOTHESIS: Contact-line motion upon drying of a sessile droplet strongly affects the solute transport and solvent evaporation profile. Hence, it should have a strong impact on the deposit formation and might be responsible for volcano-like, dome-like and flat deposit morphologies. EXPERIMENTS: A method based on a thin-film interference was used to track the drop height profile and contact line motion during the drying. A diverse set of drying scenarios was obtained by using inks with different solvent compositions and by adjusting the substrate wetting properties. The experimental data was compared to the predictions of a phenomenological model. FINDINGS: We highlight the essential role of contact-line mobility on the deposit morphology of solution-based inks. A pinned contact line produces exclusively ring-like deposits under normal conditions. On the contrary, drops with a mobile contact line can produce ring-, flat- or dome-like morphology. The developed phenomenological model shows that the deposit morphology depends on solvent evaporation profile, evolution of the drop radius relative to its contact angle, and the ratio between initial and maximal (gelling) solute concentration. These parameters can be adjusted by the ink solvent composition and substrate wetting behaviour, which provides a way for deposition of uniform and flat deposits via inkjet printing.

Mangiferin and Hesperidin Transdermal Distribution and Permeability through the Skin from Solutions and Honeybush Extracts (Cyclopia sp.)-A Comparison Ex Vivo Study.

Polyphenolic compounds-mangiferin and hesperidin-are, among others, the most important secondary metabolites of African shrub Cyclopia sp. (honeybush). The aim of this study was to compare the percutaneous absorption of mangiferin and hesperidin from solutions (water, ethanol 50%, (v/v)) and extracts obtained from green and fermented honeybush (water, ethanol 50%, (v/v)). Research was performed with the Bronaugh cells, on human dorsal skin. The mangiferin and hesperidin distributions in skin layers (stratum corneum, epidermis, and dermis) and in acceptor fluid (in every 2, 4, 6, and 24 h) were evaluated by HPLC-Photodiode Array Coulometric and Coulometric Electrochemical Array Detection. The transdermal distribution of hesperidin was also demonstrated by fluorescence microscopy. Results indicated that mangiferin and hesperidin were able to cross the stratum corneum and penetrate into the epidermis and dermis. An advantage of hesperidin penetration into the skin from the water over ethanol solution was observed (451.02 ± 14.50 vs. 357.39 ± 4.51 ng/cm2), as well as in the mangiferin study (127.56 ± 9.49 vs. 97.23 ± 2.92 ng/cm2). Furthermore, mangiferin penetration was more evident from nonfermented honeybush ethanol extract (189.85 ± 4.11 ng/cm2) than from solutions. The permeation of mangiferin and hesperidin through the skin to the acceptor fluid was observed regardless of whether the solution or the honeybush extract was applied. The highest ability to permeate the skin was demonstrated for the water solution of hesperidin (250.92 ± 16.01 ng/cm2), while the hesperidin occurring in the extracts permeated in a very low capacity. Mangiferin from nonfermented honeybush ethanol extract had the highest ability to permeate to the acceptor fluid within 24 h (152.36 ± 8.57 ng/cm2).

[Molecular Mechanisms Underlying Cellular Responses to the Loading of Non-thermal Atmospheric Pressure Plasma-activated Solutions].

Plasma medicine is a rapidly expanding new field of interdisciplinary research that combines physics, chemistry, biology, and medicine. Non-thermal atmospheric pressure plasma (NTAPP) has recently been applied to living cells and tissues, and has emerged as a novel technology for medical applications, such as wound healing, blood coagulation, and cancer treatment. NTAPP was found to affect cells indirectly through the treatment of cells with previously prepared medium irradiated by NTAPP, termed plasma-activated medium (PAM). The treatment of culture media with NTAPP results in the generation of a large amount of reactive oxygen species and reactive nitrogen species, and their derived species. We found that PAM triggered a spiral apoptotic cascade in the mitochondrial-nuclear network in A549 cancer cells. This process induced the depletion of total cellular NAD+ and elevations in intracellular calcium ion, ultimately leading to cell death. We also detected the production of hydroxyl radical and elevations in intracellular ferrous ions in PAM-treated cells. The elevations observed in ferrous ions may have been due to their release from the intracellular iron store, ferritin. However, difficulties are associated with applying PAM to the clinical phase because culture media cannot be used for medical treatments. The anti-tumor activity of plasma-activated Ringer's solution was significantly stronger than that of PAM. At the end, we herein demonstrated the advantages of the combined application of plasma-activated acetate Ringer's solution and hyperthermia, a heat treatment at 42℃, for A549 cancer cell death and elucidated the underlying mechanisms.

Synthesis of Ammonium-Based Ionic Liquids for the Extraction Process of a Natural Pigment (Betanin).

The use of new synthesized ammonium-based ionic liquids was explored as an alternative to the current process implemented in the betanin extraction from red beet juice, resulting in high yields: 70% and 82%. Betanin is a vegetal pigment that has been applied to a large variety of products in the food industry, which is important, for it can work as a substitute for the red synthetic dyes used nowadays. Additionally, the use of the kosmotropic salt sodium acetate was explored in order to separate the complex formed by the ionic liquid and pigment of interest in a process that combined two techniques: ATPS (aqueous two-phase system) and SOES (salting-out extraction system). The results reveal that the studied techniques could work as a novel process for the extraction of betanin from red beet juice employing ionic liquids, which have not been tested for this purpose in other research.

Structural properties of diluted alkali-soluble pectin from Pyrus communis L. in water and salt solutions.

The self-assembly and gelation of low-methoxyl diluted alkali-soluble pectin (LM DASP) from pear fruit (Pyrus communis L. cv. Conference) was studied in water and salt solutions (NaCl and CaCl2, constant ionic strength) without pH adjustment at 20 °C. The samples at different LM DASP concentrations were characterized using rheological tests, Fourier-transform infrared spectroscopy, dual-angle dynamic light scattering and atomic force microscopy. LM DASP from pear fruit (Pyrus communis L.) showed gelling ability. The indices (aggregation index and shape factor) based on light scattering may be useful for the characterization of structural changes in polysaccharide suspension, particularly for the determination of a gel point. The results obtained may be important for the food, cosmetic and pharmaceutical industries where pectin is used as a texturizer, an encapsulating agent, a carrier of bioactive substances or a gelling agent.

Enhancing safety and quality of shrimp by nanoparticles of sodium alginate-based edible coating containing grapefruit seed extract.

Edible coatings are safe and effective in extending the shelf life of foods. In this study, a nanoparticle-based edible coating solution was prepared, containing alginate as a coating agent and grapefruit seed extract as an antibacterial agent to improve the safety and quality of shrimp during storage. Shrimp coated with this formulation were maintained at 4°C for 8 days, and periodically analyzed for changes in sensory, chemical [total volatile basic nitrogen (TVB-N) and pH] and microbial parameters. The uncoated shrimp exceeded the microbiological limits at 7.87 log CFU/g on Day 4 of storage, whereas the nanoparticle-based coated shrimp did not exceed the limit by Day 8 of storage. In addition, uncoated shrimp tended to maintain their quality, while uncoated shrimp deteriorated due to increased TVB-N values, pH values, and off-flavors. Nanoparticles are easily dispersed in food to minimize flavor impact and enhance diffusion and bioactivity. We concluded that the nanoparticles coating extended the shelf life of shrimp by more than 5 days. Therefore, the use of nanoparticle-based coatings could be a new and effective way to maintain shrimp quality.

Simultaneous Recovery of High Quality Black Sesame Oil and Defatted Meal by a New Aqueous Method: Optimization and Comparison with Other Methods.

A method able to simultaneously obtain oil and defatted meal (rich in proteins) with high quality is preferable to others for processing black sesame seeds, which should also be green, healthy, highly efficient and sustainable. Methods including solvent extraction and hot-pressing currently available for the commercial production of oils are not able to meet all criteria just mentioned above. Therefore, development of new aqueous method of extracting black sesame oil has been promoted. In our study, we developed a new aqueous method using 1.95:10 aqueous salt solution-to-ground black sesame seed ratio which simultaneously recovered 96.54% black sesame oils and defatted meal with only 3.89% residual oils and 50.1% proteins (on dry weight basis). The oil produced had low acid value at 0.43 mgKOH/kg and peroxide value 3.37 mmol/kg and good other quality indexes. We found that proper amount of water added was essential for efficiently recover black sesame oils while other factors including temperature and time of baking raw materials to deactivate lipase activity, pore size of the sieve for ground black sesame seeds to pass through, addition of salt as well as temperature and time of agitating significantly affected the recovery efficiency. As compared with other methods, the new aqueous method had higher oil recovery rate or quality and was more environmentally friendly. No waste water was discharged during separation of oils. The experimental data can be applied to guide the design and manufacture of production line of black sesame oilseeds on a pilot or commercial scale.