Effect of using scan body accessories and inter-implant distances on the accuracy of complete arch implant digital impressions: An in vitro study.

PURPOSE: To introduce a novel design for scan body accessory parts that are reusable, easy to attach and detach without permanent change of the scan body, and can be used with different inter-implant distances to enhance the accuracy of complete arch implant scans. MATERIALS AND METHODS: A maxillary polymethylmethacrylate (PMMA) model with a soft tissue replica was fabricated with four implant analogs located at tooth positions 17, 13, 22, and 27 with 18, 25, and 30 mm inter-implant distances. Four scan bodies (SBs) were attached to the implants. The model was scanned with a laboratory scanner to be used as a reference scan. A total of 40 scans were made with the same intraoral scanner and they were divided equally into two groups. Group A: Complete arch implant scans without scan body accessories (n = 20), and Group B: Complete arch implant scans with scan body accessories (n = 20). Intraoral scans were exported and superimposed on the reference scan using reverse engineering inspection software to be evaluated for 3D deviations, angular deviations, and linear deviations. Statistical analysis was performed with student t-test and analysis of variance (ANOVA) with repeated measures followed by post hoc adjusted Bonferroni test. The level of significance was set at P = 0.05. RESULTS: The scan body accessories decreased both the 3D and linear deviations, with a statistically significant difference at SB4 for the 3D deviation (P = 0.043) and the linear inter-implant discrepancies between SB1-SB2 and SB3-SB4 (P = 0.029 and < 0.001), respectively. However, there was no statistically significant difference in angular deviation between the study groups. Implant positions had significant differences within each group. CONCLUSIONS:  A significant improvement in the accuracy of the complete arch implant digital impression was achieved by using the scan body accessories, particularly in reducing the 3D and linear deviations at the most distant implant positions.

Retention of zirconia crowns to titanium bases with straight versus angled screw access channels: an invitro study.

BACKGROUND: The aim of this study was to assess the impact of abutments with angled screw access channel on the retention of zirconia crowns. METHODS: Seven implant replicas were inserted in epoxy resin blocks. Fourteen zirconia crowns for central incisor tooth were digitally fabricated and cemented to titanium bases (Ti-bases) with resin cement. Titanium bases were categorized into 2 groups (n = 7). Control group (Group STA) included straight screw access channel abutments. Study group (Group ASC) included angled screw access channel abutments. Following aging (5 °C-55 °C, 60 s; 250,000 cycles, 100 N, 1.67 Hz), the pull-off forces (N) were recorded by using retention test (1 mm/min). Types of failure were defined as (Type 1; Adhesive failure when luting agent predominantly remained on the Ti-base surface (> 90%); Type 2; Cohesive failure when luting agent remained on both Ti-base and crown surfaces; and Type 3; Adhesive failure when luting agent predominantly remained on the crown (> 90%). Statistical analysis was conducted by using (IBM SPSS version 28). Normality was checked by using Shapiro Wilk test and Q-Q plots. Independent t-test was then used to analogize the groups. RESULTS: Mean ± standard deviation of retention force records ranged from 1731.57 (63.68) N (group STA) to 1032.29 (89.82) N (group ASC), and there was a statistically significant variation between the 2 groups (P < .05). Failure modes were Type 2 for group STA and Type 3 for group ASC. CONCLUSIONS: The retention of zirconia crowns to abutments with a straight screw access channel is significantly higher than abutments with angled screw access channel.

Evaluation of prosthetic screw loosening in all-on-four implant-supported restorations with two different connection systems.

STATEMENT OF PROBLEM: The OT BRIDGE connection system can be an alternative to multiunit abutments (MUA) for patients with all-on-four implant-supported restorations. However, the amount of prosthetic screw loosening of the OT BRIDGE in comparison with the MUA used in all-on-four implant restorations is unclear. PURPOSE: The purpose of this in vitro study was to compare the loss of removal torque in the absence of load and after dynamic cyclic loading between the 2 different connection systems: OT BRIDGE attachment and MUA used in all-on-four implant-supported restorations. MATERIAL AND METHODS: Four dummy implants (Neobiotech Co Ltd) were inserted into an edentulous mandibular model according to the all-on-four concept. Sixteen screw-retained restorations were digitally fabricated and assigned to 2 groups: the OT BRIDGE group received 8 restorations connected with OT BRIDGE (Rhein 83 srl); the MUA group received 8 restorations connected with MUA (Neobiotech Co Ltd). Restorations were tightened to the abutments according to the manufacturers' recommendations by using a digital torque gauge. The removal torque value (RTV) was measured with the same digital torque gauge. After retightening, dynamic cyclic loading was applied by using a pneumatic custom cyclic loading machine. RTV after loading was measured with the same torque gauge. From the RTVs measured, the ratios of removal torque loss (RTL) before and after loading and the difference between before and after loading were calculated. Data were analyzed by using the independent samples t test, paired samples t test, and mixed model analysis of variance (α=.05). RESULTS: The OT BRIDGE showed significantly higher RTL before loading ratio (%) than the MUA in anterior abutments (P=.002) and posterior abutments (P=.003), as well as significantly higher RTL after loading ratio (%) in anterior abutments (P=.02). The MUA showed significantly higher RTL difference between before and after loading ratio (%) than the OT BRIDGE in both anterior (P=.001) and posterior abutments (P<.001). In both systems, posterior abutments showed significantly higher RTL after loading ratio (%) than anterior abutments (P<.001). CONCLUSIONS: Posterior abutments showed more prosthetic screw loosening than anterior ones in both systems. The OT BRIDGE showed higher total prosthetic screw loosening than the MUA, although this was not significant in posterior abutments after loading. However, the OT BRIDGE was less affected by cyclic loading than the MUA.

Evaluation of physicomechanical properties of milled versus 3D-printed denture base resins: A comparative in vitro study.

STATEMENT OF PROBLEM: Studies comparing the physicomechanical characteristics of denture base resins manufactured by computer-aided design and computer-aided manufacturing (CAD-CAM) milling and 3-dimensional (3D) printing are sparse, resulting in challenges when choosing a fabrication method for complete dentures. PURPOSE: The purpose of this in vitro study was to evaluate and compare the impact strength, flexural strength, and the surface roughness of denture base resins manufactured by CAD-CAM milling and 3D printing before and after thermocycling and polishing. MATERIAL AND METHODS: Evaluation of the physicomechanical properties (n=35) was completed before and after 500 thermocycles. Impact strength (n=14) was measured with a Charpy impact tester and flexural strength (n=14) with the 3-point bend test. Surface roughness (Ra) was evaluated (n=7) with a profilometer before and after thermocycling and polishing and by viewing the surface topography before and after polishing using a scanning electron microscope at ×2000. The Mann-Whitney U test and Wilcoxon sign rank test were used for statistical analysis (α=.05). RESULTS: Milled specimens showed statistically significantly higher impact strength before thermocycling and statistically significantly higher flexural strength before and after thermocycling (P=.004) compared with 3D-printed specimens. The Ra values for the milled group were significantly lower than for the 3D-printed group both before and after thermocycling (P=.006) and after polishing (P=.027). Thermocycling resulted in a statistically significant difference in flexural strength (P=.018) in both groups and in surface roughness in the milled group (P=.048); but no significant effect was found on impact strength (P>.05). Ra values for the 3D-printed group decreased after polishing (P=.048). CONCLUSIONS: Milled specimens had higher flexural and impact strength and lower surface roughness values than 3D-printed specimens. Polishing significantly reduced the surface roughness in 3D-printed specimens but had no significant effect on milled specimens.

Registration of maxillomandibular relationship through a fully digital workflow for complete-mouth rehabilitation with screw-retained fixed implant-supported prostheses: A clinical report.

Digital recording of the maxillomandibular relationship by using intraoral scanning in completely edentulous patients for computer-aided design and computer-aided manufacture implant-supported prostheses can be challenging. This clinical report describes the fabrication of complete-arch, screw-retained implant-supported prostheses in a completely edentulous patient with a fully digital workflow.

Comparison of the strain developed around implants with angled abutments with two reinforced polymeric CAD-CAM superstructure materials: An in vitro comparative study.

STATEMENT OF PROBLEM: The strain developed around implants with angled abutments should be considered when selecting a superstructure material. Studies that evaluated the strain developed around implants with angled abutments when using fiber-reinforced polymer as the implant superstructure material are lacking. PURPOSE: The purpose of this in vitro study was to assess the strain developed around implants with angled abutments (15 and 25 degrees) of biocompatible high-performance polymer (BioHPP) and reinforced nanohybrid polymer with a multilayered glass fiber (TRINIA) superstructure under axial and oblique loading. The strain developed around implants was evaluated by using strain gauges. MATERIAL AND METHODS: Thirty-two polyurethane test blocks were divided into 2 main groups (n=16) according to the degrees of buccal tilting of the implant platform (15 and 25 degrees). Each group was divided into 2 subgroups (n=8), and each subgroup received different superstructure materials (BioHPP or TRINIA). Two buccal and palatal strain gauges were installed on their corresponding prepared sites to measure the microstrains in the medium surrounding the implant. A universal testing machine was used to apply the static load from 0 to 100 N in the axial and 45-degree oblique direction, with the loading tip of the device on the loading point at the central fossa of the crown. For each tested implant, loads were applied, microstrains were recorded with the strain gauges, and the strain developed around the implant was statistically evaluated with 1-way ANOVA, followed by multiple pairwise comparisons by using the Bonferroni adjusted significance level (α=.05). RESULTS: For superstructure materials, the microstrain values recorded around implants restored with TRINIA were significantly lower than those restored with BioHPP in all groups (P<.001). The 25-degree implant angulation recorded significantly higher microstrain than 15 degrees buccally and palatally when axial and oblique loads were applied (P<.05). The microstrain was significantly higher in the oblique load than in the axial load in both the BioHPP and TRINIA groups in 15- and 25-degree implant angulations on the buccal and palatal sides (P<.001). CONCLUSIONS: The strain developed around dental implants was significantly affected by the superstructure material. The microstrain was considerably higher when the implant abutment angulation increased. When a 45-degree loading direction was used, this tendency became more pronounced.

A prospective cross-over study to evaluate the effect of two different occlusal concepts on the masseter muscle activity in implant-retained mandibular overdentures.

BACKGROUND: The purpose of this prospective cross-over study is to evaluate the effect of bilateral balanced occlusion and canine guidance occlusion on the masseter muscle activity using implant-retained mandibular overdentures. METHODS: After evaluation of 12 completely edentulous patients using cone beam computed tomography (CBCT), mucoperiosteal flaps were reflected exposing the mandibular interforaminal region. Two implants were placed in the interforaminal region for each of the 12 patients. After a healing period of 3 months, acrylic maxillary complete dentures and mandibular overdentures were fabricated with bilateral balanced occlusion for 6 patients and canine guidance occlusion for the other 6 patients. Electromyographic evaluation of the masseter muscles, during clenching on a silicon index and chewing peanuts and cake, was conducted on the patients after using their dentures for 4 weeks. Each occlusion concept was then converted into the other concept using the same dentures, and the procedure of evaluation was repeated after 4 weeks. The recordings were analyzed statistically using Wilcoxon signed ranks test. p < 0.05 was considered statistically significant. RESULTS: The highest electromyographic activity of the masseter muscles was recorded during clenching on a preformed silicon index followed by chewing peanut then cake for both occlusal concepts. The recordings of the masseter muscle associated with canine guidance occlusion were higher than bilateral balanced occlusion but with no statistically significant difference except between the right masseter muscles during clenching (p = 0.042*). CONCLUSIONS: Both bilateral balanced occlusion and canine guidance occlusion can be used successfully in implant-retained mandibular overdentures without affecting masseter muscle activity.