RESUMEN
Recycled soda-lime glass powder is a sustainable material that is also often considered a filler in cement-based composites. The changes in the surface properties of the glass particles due to the treatments were analyzed by X-ray photoelectron spectroscopy (XPS) and optical spectroscopy. We have found that there is a relatively high level of carbon contamination on the surface of the glass particles (around 30 at.%), so plasma technology and thermal annealing were tested for surface cleaning. Room temperature plasma treatment was not sufficient to remove the carbon contamination from the surface of the recycled glass particles. Instead, the room temperature plasma treatment of recycled soda-lime glass particles leads to a significant enhancement in their room temperature photoluminescence (PL) by increasing the intensity and accelerating the decay of the photoluminescence. The enhanced blue PL after room-temperature plasma treatment was attributed to the presence of carbon contamination on the glass surface and associated charge surface and interfacial defects and interfacial states. Therefore, we propose blue photoluminescence under UV LED as a fast and inexpensive method to indicate carbon contamination on the surface of glass particles.
RESUMEN
Diamond thin films can be, at a relatively low-cost, prepared with a high-density of light-emitting negatively charged silicon vacancy (SiV) centers, which opens up the possibility of their application in photonics or sensing. The films are composed of diamond grains with both the SiV centers and sp2-carbon phase, the ratio of these two components being dependent on the preparation conditions. The grain surface and the sp2-related defects might act as traps for the carriers excited within the SiV centers, consequently decreasing their internal photoluminescence (PL) quantum efficiency. Here, we show that in a 300 nm thick polycrystalline diamond film on a quartz substrate, the SiV centers in the diamond grains possess similar temperature-dependent (13-300 K) PL decay dynamics as the SiV centers in monocrystalline diamond, which suggests that most of the SiV centers are not directly interconnected with the defects of the diamond thin films, i.e. that the carriers excited within the centers do not leak into the defects of the film. The activation energy ΔE = 54 meV and the attempt frequency α = 2.6 were extracted from the measured data. These values corresponded very well with the published values for SiV centers in monocrystalline diamond. We support this claim by measuring the transient absorption via a pump and probe technique, where we separated the nanosecond recombination dynamics of carriers in SiV centers from the picosecond decay dynamics of polycrystalline diamond defects. Our results show that PL emission properties of SiV centers in polycrystalline diamond thin films prepared via chemical vapor deposition are very similar to those in monocrystalline diamond thereby opening the door for their application in diamond photonics and sensing.
RESUMEN
The present study investigates the effect of an oxidized nanocrystalline diamond (O-NCD) coating functionalized with bone morphogenetic protein 7 (BMP-7) on human osteoblast maturation and extracellular matrix mineralization in vitro and on new bone formation in vivo. The chemical structure and the morphology of the NCD coating and the adhesion, thickness and morphology of the superimposed BMP-7 layer have also been assessed. The material analysis proved synthesis of a conformal diamond coating with a fine nanostructured morphology on the Ti6Al4V samples. The homogeneous nanostructured layer of BMP-7 on the NCD coating created by a physisorption method was confirmed by AFM. The osteogenic maturation of hFOB 1.19 cells in vitro was only slightly enhanced by the O-NCD coating alone without any increase in the mineralization of the matrix. Functionalization of the coating with BMP-7 resulted in more pronounced cell osteogenic maturation and increased extracellular matrix mineralization. Similar results were obtained in vivo from micro-CT and histological analyses of rabbit distal femurs with screws implanted for 4 or 12 weeks. While the O-NCD-coated implants alone promoted greater thickness of newly-formed bone in direct contact with the implant surface than the bare material, a further increase was induced by BMP-7. It can be therefore concluded that O-NCD coating functionalized with BMP-7 is a promising surface modification of metallic bone implants in order to improve their osseointegration.
Asunto(s)
Proteína Morfogenética Ósea 7 , Oseointegración , Aleaciones , Animales , Proteína Morfogenética Ósea 7/farmacología , Materiales Biocompatibles Revestidos/química , Materiales Biocompatibles Revestidos/farmacología , Diamante/química , Matriz Extracelular , Conejos , TitanioRESUMEN
Synthetic diamond films are routinely grown using chemical vapor deposition (CVD) techniques. Due to their extraordinary combination of intrinsic properties, they are used as the functional layers in various bio-optoelectronic devices. It is a challenge to grow the dimensional layers or porous structures that are required. This study reviews the fabrication of various porous diamond-based structures using linear antenna microwave plasma (LAMWP) chemical vapor deposition (CVD), a low-cost technology for growing diamond films over a large area (>1 m2) at low pressure (<100 Pa) and at low temperature (even at 350 °C). From a technological point of view, two different approaches, i.e., templated diamond growth using three different prestructured (macro-, micro-, and nanosized) porous substrates and direct bottom-up growth of ultra-nanoporous diamond (block-stone and dendritelike) films, are successfully employed to form diamond-based structures with controlled porosity and an enhanced surface area. As a bottom-up strategy, the LAMWP CVD system allows diamond growth at as high as 80% CO2 in the CH4/CO2/H2 gas mixture. In summary, the low-pressure and cold plasma conditions in the LAMWP system facilitate the growth on three-dimensionally prestructured substrates of various materials that naturally form porous self-standing diamond structures.