Adsorptive removal of naproxen onto nano magnesium oxide-modified castor wood biochar: Treatment of pharmaceutical wastewater via sequential Fenton's-adsorption process.

This current investigation explored the thermal conversion process of castor wood into biochar, which was subsequently harnessed for removing naproxen from pharmaceutical industrial effluent via adsorption. Surface composition analyses conducted through scanning electron microscopy-energy dispersive X-ray, laser-induced breakdown spectroscopy, and Fourier-transform infrared studies unveiled the presence of nano MgO particles within the adsorbent material. Employing optimization techniques such as response surface methodology facilitated a refined approach to batch study. The optimized conditions for batch naproxen sodium (NPX) adsorption on nano-MgO-modified biochar were identified as pH 4, 1.5 g/L adsorbent dosage, and a 120-min contact time maintaining a constant NPX concentration of 10 mg/L. The adsorption capacity was calculated to be 123.34 mg/g for a nano-magnesium oxide-modified castor wood biochar (modified biochar) and 99.874 mg/g for pristine castor wood biochar (pristine biochar). Fenton's reagents comprising 15 mM of FeSO4 (7H2O) and 25 mM of H2O2 have been scrutinized under conditions of pH 3.0, a reaction time of 30 min, a temperature of 30°C, and stirring at 120 rpm, followed by batch adsorption treatment. The COD, NH3-N, NO3 -, PO4 3-, and NPX removal percentages was found to be 90%, 87%, 79%, 80%, and 90%, respectively. Thus nano MgO-modified biochar holds promise of treatment of pharmaceutical effluent.

Response surface methodology-based optimisation of adsorption of diclofenac and treatment of pharmaceutical effluent using combined coagulation-adsorption onto nFe2O3 decorated water chestnut shells biochar.

This work involved the preparation of pristine and iron nanoparticle-loaded biochar from a water chestnut shell to remove diclofenac sodium (DCF) containing effluent of pharmaceutical origin. To create suitable forecasting equations for the modelling of the DCF adsorption onto the adsorbent, response surface methodology (RSM) was used. The parameters, e.g. pH, adsorbent mass, DCF concentration and contact time, were used for the modeling of adsorption. The RSM model predicts that for 98.0% DCF removal, the ideal conditions are pH 6, an adsorbent dose of 0.5 g L-1, and a contact time of 60 min with an initial adsorbate concentration of 25 mg L-1 at 303 K. The maximum capacity deduced from the Langmuir model was 75.9 mg g-1 for pristine water chestnut shell biochar (pWCBC) and 122.3 mg g-1 for magnetically modified nano-Fe2O3 biochar (mWCBC). Under equilibrium conditions, the Langmuir model was the best-suited model compared to the Temkin and Freundlich models. The adsorption data in this investigation efficiently fitted the pseudo-second-order model, emphasizing that chemisorption or ion exchange processes may be involved in the process. The WCBC demonstrated recyclability after 10 cycles of repeated adsorption and desorption of DCF. A combined coagulation adsorption process removed COD, NH3-N, NO3-, PO43-, and DCF by 92.50%, 86.41%, 77.57%, 84.54%, and 97.25%, respectively. This study therefore shows that coagulation followed by adsorption onto biochar can be a cost-effective substitute for conventional pharmaceutical wastewater treatment.

Fluorinated Co-Solvents Enable Excellent Performances of Practical Cells Comprising LixSiO-Graphite Composite Anodes and LiNi0.89Co0.05Mn0.05Al0.01O2 (NCMA) Cathodes.

Li-ion batteries based on high specific capacity LixSiO-Graphite anodes and LiNi0.89Co0.05 Mn0.05Al0.01O2 (NCMA) cathodes may have numerous practical applications owing to high energy density without a necessary compromise on safety. SiO, which is an attractive Li insertion anode material, offers more cycling stability than Si and a higher capacity than graphite. Therefore, a new trend has emerged for developing composite C-Si anodes, possessing the excellent cyclability of graphite coupled with high capacity SiO. The composite structure described herein prevents the volume expansion of SiO and maintains the structural integrity during prolonged cycling. However, graphite electrodes suffer from exfoliation in propylene carbonate (PC) based electrolyte solutions, which avoids well known safety benefits related to a possible use of PC based electrolyte solutions in all kinds of Li batteries. Herein, it is reported that trifluoro propylene carbonate (TFPC) is compatible with graphite anodes. New electrolyte formulations are developed and tested containing fluorinated co-solvents and compared the performance of several electrolyte solutions, including conventional alkyl carbonates-based solutions in full Li-ion cells, which included LixSiO-Graphite anodes and LiNi0.89Co0.05Mn0.05Al0.01O2 (NCMA) cathodes. Cells with new electrolyte solutions developed herein demonstrated nearly twice capacity retention in prolonged cycling experiments compared to similar reference cells containing conventional electrolyte solutions.

CrI3-WTe2: A Novel Two-Dimensional Heterostructure as Multisensor for BrF3 and COCL2 Toxic Gases.

A new multisensor (i.e. resistive and magnetic) CrI3-WTe2 heterostructure (HS) to detect the toxic gases BrF3 and COCl2 (Phosgene) has been theoretically studied in our present investigation. The HS has demonstrated sensitivity towards both the gases by varying its electronic and magnetic properties when gas molecule interacts with the HS. Fast recovery time (<0.14 fs) under UV radiation has been observed. We have considered two configurations of BrF3 adsorbed HS; (1) when F ion interacts with HS (C1) and (2) when Br ion interacts with HS (C2). In C1 case the adsorption energy Ead is observed to be -0.66 eV while in C2 it is -0.95 eV. On the other hand in case of COCl2 Ead is found to be -0.42 eV. Magnetic moments of atoms are also found to vary upon gas adsorption indicates the suitability of the HS as a magnetic gas sensor. Our observations suggest the suitability of CrI3-WTe2 HS to respond detection of the toxic gases like BrF3 and COCl2.

An ab initio study of sensing applications of MoB2 monolayer: a potential gas sensor.

Using first principles density functional theory, we have studied the interaction mechanism of NO2 and SO2 gas molecules on an MoB2 monolayer, for gas sensing applications. The selectivity for a particular gas by the sensor has been analyzed through electronic structure calculations and adsorption studies. The calculations have been performed by considering the fact that the MoB2 monolayer as a sensing material encounters a change in its electrical properties, when gas molecules with different orientations get adsorbed on the surface. From the density of states study, we find better selectivity for NO2 as compared to SO2, as the latter leaves the electronic structure of the sensing material unaffected. Further, the adsorption curves support the above fact as the larger value of adsorption energy (Ead ∼ -1 eV) for NO2 indicates stronger adsorption. The chemisorptive nature for NO2, in contrast with the relatively weaker physisorption for SO2, additionally supports the fact that NO2 gas has a better perspective for MoB2 sensor application. Charge density plots for each case are in good agreement with the above conclusions. The faster recovery time attributes the MoB2 monolayer better as a sensor material for NO2 interaction.

MoB2 Driven Metallic Behavior and Interfacial Charge Transport Mechanism in MoS2/MoB2 Heterostructure: A First-Principles Study.

We have performed the density functional theory calculations on heterostructure (HS) of MoS2 and MoB2 monolayers. The aim of this study is to assess the influence of MoB2 on electron transport of adjacent MoS2 layer. In present investigation we predict that the electronic properties of MoS2 monolayer is influenced by 4d-states of Mo in MoB2 monolayer. Whereas, the B atoms of MoB2 and S atoms of MoS2 exhibit overlapping of intermediate atomic orbitals thereby collectively construct the interfacial electronic structure observed to be metallic in nature. From charge density calculations, we have also determine that the charge transfer is taking place at the interface via B-2p and S-3p states. The bonds at the interface are found to be metallic which is also confirmed by adsorption analysis. Thermoelectric performance of this HS is found be in good agreement with available literature. Low Seebeck coefficient and high electrical conductivity further confirms the existence of metallic state of the HS.

Interfacial Coupling Effect on Electron Transport in MoS2/SrTiO3 Heterostructure: An Ab-initio Study.

A variety of theoretical and experimental works have reported several potential applications of MoS2 monolayer based heterostructures (HSs) such as light emitting diodes, photodetectors and field effect transistors etc. In the present work, we have theoretically performed as a model case study, MoS2 monolayer deposited over insulating SrTiO3 (001) to study the band alignment at TiO2 termination. The interfacial characteristics are found to be highly dependent on the interface termination. With an insulating oxide material, a significant band gap (0.85eV) is found in MoS2/TiO2 interface heterostructure (HS). A unique electronic band profile with an indirect band gap (0.67eV) is observed in MoS2 monolayer when confined in a cubic environment of SrTiO3 (STO). Adsorption analysis showed the chemisorption of MoS2 on the surface of STO substrate with TiO2 termination which is justified by the charge density calculations that shows the existence of covalent bonding at the interface. The fabrication of HS of such materials paves the path for developing the unprecedented 2D materials with exciting properties such as semiconducting devices, thermoelectric and optoelectronic applications.