The Effects of Metabolism Tracker Device (Lumen) Usage on Metabolic Control in Adults with Prediabetes: Pilot Clinical Trial.

INTRODUCTION: Prediabetes is a risk factor for type 2 diabetes mellitus (T2DM). However, it may be reversed via lifestyle changes. Lumen is a novel handheld device that measures exhaled CO2 producing results in agreement with those of indirect calorimetry when assessing metabolic fuel usage. The aim of this study was to examine the effects of following Lumen's personalized, measurement-guided lifestyle intervention program on anthropometric and metabolic variables in adults with prediabetes. METHODS: A 12-week single-arm intervention study was conducted in 27 participants. Body composition and blood markers were measured at the start and end of the study. Each participant took a daily morning (fasted) measurement and received feedback on their metabolic state (i.e., their degree of fat vs. carbohydrate oxidation). Participants were then provided with personalized daily guidelines for their carbohydrate, fat, and protein consumption, along with recommended lifestyle changes. RESULTS: Intention-to-treat analysis revealed a significant decrease in body weight (5.99 kg, p < 0.001), comprising a significant reduction in percentage body fat (2.93%, p < 0.001) and waist circumference (6.23 cm, p < 0.001). Significant reductions were also observed in glycated hemoglobin A1c (0.27%, p < 0.001), triglycerides (0.45 mg/dL, p < 0.001), and systolic blood pressure (0.5 mm Hg, p < 0.05). CONCLUSION: In a 12-week pilot study of participants with prediabetes, Lumen usage significantly improved multiple metabolic parameters, demonstrating its potential to deliver better clinical outcomes for patients with T2DM and metabolic syndrome.

Monitoring the Progression of Cell-Free Expression of Microbial Rhodopsins by Surface Enhanced IR Spectroscopy: Resolving a Branch Point for Successful/Unsuccessful Folding.

The translocon-unassisted folding process of transmembrane domains of the microbial rhodopsins sensory rhodopsin I (HsSRI) and II (HsSRII), channelrhodopsin II (CrChR2), and bacteriorhodopsin (HsBR) during cell-free expression has been investigated by Surface-Enhanced Infrared Absorption Spectroscopy (SEIRAS). Up to now, only a limited number of rhodopsins have been expressed and folded into the functional holoprotein in cell free expression systems, while other microbial rhodopsins fail to properly bind the chromophore all-trans retinal as indicated by the missing visible absorption. SEIRAS experiments suggest that all investigated rhodopsins lead to the production of polypeptides, which are co-translationally inserted into a solid-supported lipid bilayer during the first hour after the in-vitro expression is initiated. Secondary structure analysis of the IR spectra revealed that the polypeptides form a comparable amount of α-helical structure during the initial phase of insertion into the lipid bilayer. As the process progressed (>1 h), only HsBR exhibited a further increase and association of α-helices to form a compact tertiary structure, while the helical contents of the other rhodopsins stagnated. This result suggests that the molecular reason for the unsuccessful cell-free expression of the two sensory rhodopsins and of CrChR2 is not due to the translation process, but rather to the folding process during the post-translational period. Taking our previous observation into account that HsBR fails to form a tertiary structure in the absence of its retinal, we infer that the chromophore retinal is an integral component of the compaction of the polypeptide into its tertiary structure and the formation of a fully functional protein.

High wear resistance of femoral components coated with titanium nitride: a retrieval analysis.

PURPOSE: The objective of this study was to evaluate the in vivo wear resistance of cobalt-chromium femoral components coated with titanium nitride (TiN). Our null hypothesis was that the surface damage and the thickness of the TiN coating do not correlate with the time in vivo. METHODS: Twenty-five TiN-coated bicondylar femoral retrievals with a mean implantation period of 30.7 ± 11.7 months were subjected to an objective surface damage analysis with a semi-quantitative assessment method. A visual examination of scratches, indentations, notches and coating breakthroughs of the surfaces was performed. The roughness and the coating thickness of the TiN coating were evaluated in the main articulation regions. RESULTS: Narrow scratches and indentations in the range of low flexion angles on the retrieval surfaces were the most common modes of damage. There was no evidence of delamination on the articulation surface but rather at the bottom of isolated severe indentations or notches. An analysis of three retrievals revealed a coating breakthrough in the patellofemoral joint region, resulting from patella maltracking and a dislocation. The arithmetical mean roughness of the TiN surface slightly increased with the implantation period. In contrast, the maximum peak height of the roughness profile was reduced at the condyles of the retrieved components in comparison with new, unused surfaces. No significant association between the coating thickness and implantation period was determined. Moreover, the measured values were retained in the range of the initial coating thickness even after several years of in vivo service. CONCLUSIONS: As was demonstrated by the results of this study, the surface damage to the TiN coating did not deteriorate with the implantation period. The calculated damage scores and the measured coating thickness in particular both confirmed that the TiN coating provides low wear rates. Our findings support the use of wear-resistant TiN-coated components in total knee arthroplasty with the objective of reducing the risk of aseptic loosening. However, in terms of TiN-coated femoral components, particular attention should be paid to a correct patellar tracking in order to avoid wear propagation at the implant.

Characterization of thick titanium plasma spray coatings on PEEK materials used for medical implants and the influence on the mechanical properties.

Coating poly-ether-ether-ketone (PEEK) with rough and porous titanium plasma spray (TPS) coatings is a technique which is commonly used to enhance the osseointegrative properties of medical implants. However, the influence of the TPS coating on the PEEK mechanical properties has not been sufficiently evaluated to date. In this study, PEEK samples were coated with a thick TPS layer with grains of 90µm and 180µm diameter. The coating characteristics and the adhesive strength of the coatings on the samples were determined and compared to coatings on titanium samples. The influence of the coating process on the mechanical and chemical-physical properties of PEEK was also evaluated. All TPS coatings on PEEK and titanium fulfilled the manufacturer's requirements for thickness (200 ± 50µm), porosity (30 ± 10%) and roughness (90µm grain diameter coating: 25 ± 5µm and 180µm grain diameter coating: 45 ± 15µm) and were able to meet the demands required for adhesive strength (> 22MPa) and shear strength (> 20MPa). However, the mechanical properties i.e. yield stress, fracture strain, flexural modulus and flexural stress, of the PEEK samples were influenced by the coating process, while the chemical-physical properties were not altered.

In-Situ Observation of Membrane Protein Folding during Cell-Free Expression.

Proper insertion, folding and assembly of functional proteins in biological membranes are key processes to warrant activity of a living cell. Here, we present a novel approach to trace folding and insertion of a nascent membrane protein leaving the ribosome and penetrating the bilayer. Surface Enhanced IR Absorption Spectroscopy selectively monitored insertion and folding of membrane proteins during cell-free expression in a label-free and non-invasive manner. Protein synthesis was performed in an optical cell containing a prism covered with a thin gold film with nanodiscs on top, providing an artificial lipid bilayer for folding. In a pilot experiment, the folding pathway of bacteriorhodopsin via various secondary and tertiary structures was visualized. Thus, a methodology is established with which the folding reaction of other more complex membrane proteins can be observed during protein biosynthesis (in situ and in operando) at molecular resolution.