Boosting the Efficiency of Perovskite/Organic Tandem Solar Cells via Enhanced Near-Infrared Absorption and Minimized Energy Losses.

The compatibility of perovskite and organic photovoltaic materials in solution processing provides a significant advantage in the fabrication of high-efficiency perovskite/organic tandem solar cells. However, additional recombination losses can occur during exciton dissociation in organic materials, leading to energy losses in the near-infrared region of tandem devices. Consequently, a ternary organic rear subcell is designed containing two narrow-bandgap non-fullerene acceptors to enhance the absorption of near-infrared light. Simultaneously, a unique diffusion-controlled growth technique is adopted to optimize the morphology of the ternary active layer, thereby improving exciton dissociation efficiency. This innovation not only broadens the absorption range of near-infrared light but also facilitates the generation and effective dissociation of excitons. Owing to these technological improvements, the power conversion efficiency (PCE) of organic solar cells increased to 19.2%. Furthermore, a wide-bandgap perovskite front subcell is integrated with a narrow-bandgap organic rear subcell to develop a perovskite/organic tandem solar cell. Owing to the reduction in near-infrared energy loss, the PCE of this tandem device significantly improved, reaching 24.5%.

Constructing Multiscale Fibrous Morphology to Achieve 20% Efficiency Organic Solar Cells by Mixing High and Low Molecular Weight D18.

This study underscores the significance of precisely manipulating the morphology of the active layer in organic solar cells (OSCs). By blending polymer donors of D18 with varying molecular weights, a multiscale interpenetrating fiber network structure within the active layer is successfully created. The introduction of 10% low molecular weight D18 (LW-D18) into high molecular weight D18 (HW-D18) produces MIX-D18, which exhibits an extended exciton diffusion distance and orderly molecular stacking. Devices utilizing MIX-D18 demonstrate superior electron and hole transport, improves exciton dissociation, enhances charge collection efficiency, and reduces trap-assisted recombination compared to the other two materials. Through the use of the nonfullerene acceptor L8-BO, a remarkable power conversion efficiency (PCE) of 20.0% is achieved. This methodology, which integrates the favorable attributes of high and low molecular weight polymers, opens a new avenue for enhancing the performance of OSCs.

Highly efficient and stable binary and ternary organic solar cells using polymerized nonfused ring electron acceptors.

This study reports the successful design and synthesis of two novel polymerized nonfused ring electron acceptors, P-2BTh and P-2BTh-F, derived from the high-performance nonfused ring electron acceptor, 2BTh-2F. Prepared via Stille polymerization, these polymers feature thiophene and fluorinated thiophene as π-bridge units. Notably, P-2BTh-F, with difluorothiophene as the π-bridge, exhibits a more planar backbone and red-shifted absorption spectrum compared with P-2BTh. When employed in organic solar cells (OSCs) with PBDB-T as the donor material, P-2BTh-F-based devices demonstrate an outstanding power conversion efficiency (PCE) of over 11%, exceeding the 8.7% achieved by P-2BTh-based devices. Furthermore, all-polymer solar cells utilizing PBDB-T:P-2BTh-F exhibit superior storage stability. Additionally, P-2BTh-F was explored as a functional additive in a high-performance binary system, enhancing stability while maintaining comparable PCE (19.45%). This strategy offers a cost-effective approach for fabricating highly efficient and stable binary and ternary organic solar cells, opening new horizons for cost-effective and durable solar cell development.

Boosting Organic Solar Cells to Over 18% Efficiency through Dipole-Dipole Interactions in Fluorinated Nonfused Ring Electron Acceptors.

This study successfully designed and synthesized two nonfused ring electron acceptors, 412-6F and 412-6Cl, modified with fluorine and chlorine substituents, respectively. Single-crystal analysis revealed that 412-6F possesses a planar molecular backbone and exhibits pronounced dipole-dipole interactions between the fluorine atoms on the lateral phenyl groups and the carbonyl oxygen atoms on the end groups. This specific interaction promotes dense end-group stacking, leading to a reduced interlayer spacing. Improved crystallinity and coherence length are observed in the D18:412-6F blend film. Conversely, 412-6Cl adopts a more distorted configuration and lacks these interactions. As a result, the organic solar cell (OSC) based on D18:412-6F achieved a remarkable power conversion efficiency of 18.03%, surpassing the performance of the D18:412-6Cl OSC. This underscores the importance of designing novel acceptors with beneficial intermolecular interactions to enhance OSC efficiency, thus providing a new direction for organic photovoltaic advancement.

Promotion of Fast and Efficient Singlet Fission Process of PDI Dimers by Selenium Substitution.

Singlet fission (SF) is a triplet generation mechanism capable of turning a singlet exciton into two triplet excitons. It has the potential to enhance the power conversion efficiency of single-junction solar cells. Perylene diimides (PDIs) are a class of dye molecules with photovoltaic properties and are beginning to receive more and more attention due to their potential for SF. Here, we report a selenium-substituted PDI dimer, Se-PDI-II, and we studied its SF mechanism by using steady-state, transient absorption, and time-resolved photoluminescence spectroscopy. Compared with the unsubstituted dimer PDI-II, we found that the introduction of selenium atoms can suppress excimer emission during the SF process, showing much higher SF efficiency and triplet yield.

Hierarchical Solid-Additive Strategy for Achieving Layer-by-Layer Organic Solar Cells with Over 19 % Efficiency.

Layer-by-layer (LbL) deposition of active layers in organic solar cells (OSCs) offers immense potential for optimizing performance through precise tailoring of each layer. However, achieving high-performance LbL OSCs with distinct solid additives in each layer remains challenging. In this study, we explore a novel approach that strategically incorporates different solid additives into specific layers of LbL devices. To this end, we introduce FeCl3 into the lower donor (D18) layer as a p-type dopant to enhance hole concentration and mobility. Concurrently, we incorporate the wide-band gap conjugated polymer poly(9,9-di-n-octylfluorenyl-2,7-diyl) (PFO) into the upper acceptor (L8-BO) layer to improve the morphology and prolong exciton lifetime. Unlike previous studies, our approach combines these two strategies to achieve higher and more balanced electron and hole mobility without affecting device open-circuit voltage, while also suppressing charge recombination. Consequently, the power conversion efficiency (PCE) of the D18+FeCl3/L8-BO device increases to 18.12 %, while the D18/L8-BO+PFO device attains a PCE of 18.79 %. These values represent substantial improvements over the control device's PCE of 17.59 %. Notably, when both FeCl3 and PFO are incorporated, the D18+FeCl3/L8-BO+PFO device achieves a remarkable PCE of 19.17 %. In summary, our research results demonstrate the effectiveness of the layered solid additive strategy in improving OSC performance.

Designing A-D-A Type Fused-Ring Electron Acceptors with a Bulky 3D Substituent at the Central Donor Core to Minimize Non-Radiative Losses and Enhance Organic Solar Cell Efficiency.

Designing and synthesizing narrow band gap acceptors that exhibit high photoluminescence quantum yield (PLQY) and strong crystallinity is a highly effective, yet challenging, approach to reducing non-radiative energy losses (▵Enr) and boosting the performance of organic solar cells (OSCs). We have successfully designed and synthesized an A-D-A type fused-ring electron acceptor, named DM-F, which features a planar molecular backbone adorned with bulky three-dimensional camphane side groups at its central core. These bulky substituents effectively hinder the formation of H-aggregates of the acceptors, promoting the formation of more J-aggregates and notably elevating the PLQY of the acceptor in the film. As anticipated, DM-F showcases pronounced near-infrared absorption coupled with impressive crystallinity. Organic solar cells (OSCs) leveraging DM-F exhibit a high EQEEL value and remarkably low ▵Enr of 0.14 eV-currently the most minimal reported value for OSCs. Moreover, the power conversion efficiency (PCE) of binary and ternary OSCs utilizing DM-F has reached 16.16 % and 20.09 %, respectively, marking a new apex in reported efficiency within the OSCs field. In conclusion, our study reveals that designing narrow band gap acceptors with high PLQY is an effective way to reduce ▵Enr and improve the PCE of OSCs.

A 3,3'-Difluoro-2,2'-Bithiophene Based Donor Polymer Realizing High Efficiency (>17%) Single Junction Binary Organic Solar Cells.

In this study, two novel donor-acceptor (D-A) copolymers are designed and synthesized, DTBT-2T and DTBT-2T2F with 2,2'-bithiophene or 3,3'-difluoro-2,2'-bithiophene as the donor unit and dithienobenzothiadiazole as the acceptor unit, and used them as donor materials in non-fullerene organic solar cells (OSCs). Due to enhanced planarity of polymer chains resulted by the intramolecular F···S noncovalent interactions, the incorporation of 3,3'-difluoro-2,2'-bithiophene unit instead of 2,2'-bithiophene into the polymers can enhance their molecular packing, crystallinity and hole mobility. The DTBT-2T:L8-BO based binary OSCs deliver a power conversion efficiency (PCE) of only 9.71% with a Voc of 0.78 V, a Jsc of 20.69 mA cm-2 , and an FF of 59.67%. Moreover, the introduction of fluoro atoms can lower the highest occupied molecular orbital levels. As a result, DTBT-2T2F:L8-BO based single-junction binary OSCs exhibited less recombination loss, more balanced charge mobility, and more favorable morphology, resulting in an impressive PCE of 17.03% with a higher Voc of 0.89 V, a Jsc of 25.40 mA cm-2, and an FF of 75.74%. These results indicate that 3,3'-difluoro-2,2'-bithiophene unit can be used as an effective building block to synthesize high performance polymer donor materials. This work greatly expands the selection range of donor units for constructing high-performance polymers.

Sequentially Processed Bulk-Heterojunction-Buried Structure for Efficient Organic Solar Cells with 500 nm Thickness.

Large-area printing fabrication is a distinctive feature of organic solar cells (OSCs). However, the advance of upscalable fabrication is challenged by the thickness of organic active layers considering the importance of both exciton dissociation and charge collection. In this work, a bulk-heterojunction-buried (buried-BHJ) structure is introduced by sequential deposition to realize efficient exciton dissociation and charge collection, thereby contributing to efficient OSCs with 500 nm thick active layers. The buried-BHJ distributes donor and acceptor phases in the vertical direction as charge transport channels, while numerous BHJ interfaces are buried in each phase to facilitate exciton dissociation simultaneously. It is found that buried-BHJ configurations possess efficient exciton dissociation and rapid charge transport, resulting in reduced recombination losses. In comparison with traditional structures, the buried-BHJ structure displays a decent tolerance to film thickness. In particular, a power conversion efficiency of 16.0% is achieved with active layers at a thickness of 500 nm. To the best of the authors' knowledge, this represents the champion efficiency of thick film OSCs.

Decreasing exciton dissociation rates for reduced voltage losses in organic solar cells.

Enhancing the device electroluminescence quantum efficiency (EQEEL) is a critical factor in mitigating non-radiative voltage losses (VNR) and further improving the performance of organic solar cells (OSCs). While the common understanding attributes EQEEL in OSCs to the dynamics of charge transfer (CT) states, persistent efforts to manipulate these decay dynamics have yielded limited results, with the EQEEL of high-efficiency OSCs typically remaining below 10-2%. This value is considerably lower than that observed in high efficiency inorganic photovoltaic devices. Here, we report that EQEEL is also influenced by the dissociation rate constant of singlet states (kDS). Importantly, in contrast to the traditional belief that advocates maximizing kDS for superior photovoltaic quantum efficiency (EQEPV), a controlled reduction in kDS is shown to enhance EQEEL without compromising EQEPV. Consequently, a promising experimental approach to address the VNR challenge is proposed, resulting in a significant improvement in the performance of OSCs.

High-Efficiency Binary and Ternary Organic Solar Cells Based on Novel Nonfused-Ring Electron Acceptors.

In this study, three nonfused-ring electron acceptors (2TT, 2TT-C6-F, and 2TT-C11-F) with the same steric hindrance groups (2,4,6-tripropylbenzene) are designed and synthesized and the impact of electron-withdrawing and lateral alkyl side chains on the performance of binary and ternary organic solar cells (OSCs) is explored. For the binary OSCs, 2TT-C11-F with IC-2F terminal groups and lateral undecyl side chains display a red shifted absorption spectrum and suitable energy levels, and the corresponding blend film exhibits appropriate phase separation and crystallinity. Thus, binary OSCs based on 2TT-C11-F achieve an impressive power conversion efficiency of 13.03%, much higher than the efficiencies of those based on 2TT (9.68%) and 2TT-C6-F (12.11%). In the ternary OSCs, 2TT with CC terminal groups and lateral hexyl side chains exhibit complementary absorption and cascade energy levels with a host binary system (D18:BTP-eC9-4F). Hence, the ternary OSCs based on 2TT achieve a remarkable efficiency of 19.39%, ranking among the highest reported values. The research yields comprehensive 2TT-series nonfused-ring electron acceptors, demonstrating their great potential for the fabrication of high-performance binary and ternary OSCs.

Halogenated Nonfused Ring Electron Acceptor for Organic Solar Cells with a Record Efficiency of over 17.

Three nonfused ring electron acceptors (NFREAs), namely, 3TT-C2-F, 3TT-C2-Cl, and 3TT-C2, are purposefully designed and synthesized with the concept of halogenation. The incorporation of F or/and Cl atoms into the molecular structure (3TT-C2-F and 3TT-C2-Cl) enhances the π-π stacking, improves electron mobility, and regulates the nanofiber morphology of blend films, thus facilitating the exciton dissociation and charge transport. In particular, blend films based on D18:3TT-C2-F demonstrate a high charge mobility, an extended exciton diffusion distance, and a well-formed nanofiber network. These factors contribute to devices with a remarkable power conversion efficiency of 17.19%, surpassing that of 3TT-C2-Cl (16.17%) and 3TT-C2 (15.42%). To the best of knowledge, this represents the highest efficiency achieved in NFREA-based devices up to now. These results highlight the potential of halogenation in NFREAs as a promising approach to enhance the performance of organic solar cells.

Precise Methylation Yields Acceptor with Hydrogen-Bonding Network for High-Efficiency and Thermally Stable Polymer Solar Cells.

Utilizing intermolecular hydrogen-bonding interactions stands for an effective approach in advancing the efficiency and stability of small-molecule acceptors (SMAs) for polymer solar cells. Herein, we synthesized three SMAs (Qo1, Qo2, and Qo3) using indeno[1,2-b]quinoxalin-11-one (Qox) as the electron-deficient group, with the incorporation of a methylation strategy. Through crystallographic analysis, it is observed that two Qox-based methylated acceptors (Qo2 and Qo3) exhibit multiple hydrogen bond-assisted 3D network transport structures, in contrast to the 2D transport structure observed in gem-dichlorinated counterpart (Qo4). Notably, Qo2 exhibits multiple and stronger hydrogen-bonding interactions compared with Qo3. Consequently, PM6 : Qo2 device realizes the highest power conversion efficiency (PCE) of 18.4 %, surpassing the efficiencies of devices based on Qo1 (15.8 %), Qo3 (16.7 %), and Qo4 (2.4 %). This remarkable PCE in PM6 : Qo2 device can be primarily ascribed to the enhanced donor-acceptor miscibility, more favorable medium structure, and more efficient charge transfer and collection behavior. Moreover, the PM6 : Qo2 device demonstrates exceptional thermal stability, retaining 82.8 % of its initial PCE after undergoing annealing at 65 °C for 250 hours. Our research showcases that precise methylation, particularly targeting the formation of intermolecular hydrogen-bonding interactions to tune crystal packing patterns, represents a promising strategy in the molecular design of efficient and stable SMAs.

Spontaneously spreading film process to improve the photovoltaic performance of organic solar cells with PHJ structure.

Efficient charge transport and extraction within the active layer plays a major role in the photovoltaic performance of organic solar cells (OSCs). In this work, the spontaneously spreading (SS) process was utilized to achieve sequential deposition of the active layer with a planar heterojunction (PHJ) structure. The SS process avoids the damage of the upper layer solution to the lower layer film by the spin coating process. The film with PHJ structure exhibits notable vertical phase separation compared to the bulk heterojunction (BHJ). Moreover, the power conversion efficiency (PCE) of the PHJ device (12.00%) is significantly higher than that of the BHJ (10.84%) due to the efficient charge transport. This work offers a novel fabrication method and device structure to enhance the photovoltaic performance of OSCs.

Macrocyclic Encapsulation in a Non-fused Tetrathiophene Acceptor for Efficient Organic Solar Cells with High Short-Circuit Current Density.

Non-fullerene acceptors have shown great promise for organic solar cells (OSCs). However, challenges in achieving high efficiency molecular system with conformational unicity and effective molecular stacking remain. In this study, we present a new design of non-fused tetrathiophene acceptor R4T-1 via employing the encapsulation of tetrathiophene with macrocyclic ring. The single crystal structure analysis reveals that cyclic alkyl side chains can perfectly encapsulate the central part of molecule and generate a conformational stable and planar molecular backbone. Whereas, the control 4T-5 without the encapsulation restriction displays cis- and twisted conformation. As a result, R4T-1 based OSCs achieved an outstanding power conversion efficiency (PCE) exceeding 15.10 % with a high short-circuit current density (Jsc ) of 25.48 mA/cm2 , which is significantly improved by ≈30 % in relative to that of the control. Our findings demonstrate that the macrocyclic encapsulation strategy could assist fully non-fused electron acceptors (FNEAs) to achieve a high photovoltaic performance and pave a new way for FNEAs design.

High-Pressure Fabrication of Binary Organic Solar Cells with High Molecular Weight D18 Yields Record 19.65 % Efficiency.

In this work, inspired by the principles of a pressure cooker, we utilized a high-pressure method to address the processing challenges associated with high molecular weight polymers. Through this approach, we successfully dissolved high molecular weight D18 in chloroform at 100 °C within a pressure-tight vial. The increased steam pressure raised the boiling point and dissolving capacity of chloroform, enabling the creation of a hybrid film with superior properties, including more ordered molecular arrangement, increased crystallinity, extended exciton diffusion length, and improved phase morphology. Organic solar cells (OSCs) based on D18 : L8-BO prepared using this high-pressure method achieved an outstanding power conversion efficiency of 19.65 %, setting a new record for binary devices to date. Furthermore, this high-pressure method was successfully applied to fabricate OSCs based on other common systems, leading to significant enhancements in device performance. In summary, this research introduces a universal method for processing high molecular weight D18 materials, ultimately resulting in the highest performance reported for binary organic solar cells.

Improving the Performance of Layer-by-Layer Organic Solar Cells by n-Doping of the Acceptor Layer.

Molecular dopants can effectively improve the performance of organic solar cells (OSCs). Here, PM6/BTP-eC9-4Cl-based OSCs are fabricated by a layer-by-layer (LbL) deposition method, and the electron acceptor BTP-eC9-4Cl layer is properly doped by n-type dopant benzyl viologen (BV) or [4-(1,3-dimethyl-2,3-dihydro-1H-benzoimidazol-2-yl)phenyl]dimethyl-amine (N-DMBI-H). The power conversion efficiency (PCE) of OSCs increases from 16.80 to 17.61 or 17.84% when the acceptor layer is doped by BV (0.01 wt %) or N-DMBI-H (0.01 wt %), respectively. At the optimal doping concentration, the device exhibits more balanced charge transport, fewer bimolecular recombinations, faster charge separation and transfer, and better stability. This doping strategy has good universality; when the acceptor layer L8-BO of LbL OSCs is doped by 0.01 wt % BV or 0.01 wt % N-DMBI-H, the PCE increases from 17.49 to 18.35 or 18.25%, respectively. All in all, our studies have demonstrated that the doping strategy is effective in enhancing the performance of OSCs.

Improving the Performance of Layer-by-Layer Processed Organic Solar Cells via Introducing a Wide-Bandgap Dopant into the Upper Acceptor Layer.

The layer-by-layer (LbL) solution-processed organic solar cells (OSCs) are conductive to achieve vertical phase separation, tunable donor-acceptor (D/A) interfaces, and favorable charge-transport pathways. In this work, a wide-bandgap component poly(9-vinylcarbazole) (PVK) is added to the upper electron acceptor layer to improve the performance of LbL-processed OSCs. Results show that the PVK component can adjust the film morphology, dope the electron acceptor, increase the electron concentration, and improve charge transport. Such n-type doping is verified by Seebeck coefficient measurement, ultraviolet photoelectron spectroscopy, and electron paramagnetic resonance characterization. In addition, the fluorescence intensity and exciton lifetime of the PVK-doped acceptor film are increased, thus being beneficial for exciton diffusion to the D/A interface. Therefore, the power conversion efficiency (PCE) of LbL OSCs increases when 2.50 wt.% PVK is employed in the electron acceptor layer of commonly-used high-efficiency system and a maximum value of 19.05% can be achieved. The role of PVK played in the active layer is different from those of additives and ternary components reported previously, so the results provide an alternative way to enhance the device performance of LbL-processed OSCs.

Intramolecular and Intermolecular Interaction Switching in the Aggregates of Perylene Diimide Trimer: Effect of Hydrophobicity.

The research on perylene diimide (PDI) aggregates effectively promotes their applications in organic photovoltaic solar cells and fluorescent sensors. In this paper, a PDI fabricated with three peripheral PDI units (N, N'-bis(6-undecyl) perylene-3,4,9,10-bis(dicarboximide)) is investigated. The trimer shows different absorption and fluorescence properties due to hydrophobicity when dissolved in the mixed solvent of tetrahydrofuran (THF) and water. Through comprehensive analysis of the fluorescence lifetime and transient absorption spectroscopic results, we concluded that the trimer underwent different excited state kinetic pathways with different concentrations of water in THF. When dissolved in pure THF solvent, both the intramolecular charge-transfer and excimer states are formed. When the water concentration increases from 0 to 50% (v/v), the formation time of the excimer state and its structural relaxation time are prolonged, illustrating the arising of the intermolecular excimer state. It is interesting to determine that the probability of the intramolecular charge-transfer pathway will first decrease and then increase as the speed of intermolecular excimer formation slows down. The two inflection points appear when the water concentration is above 10% and 40%. The results not only highlight the importance of hydrophobicity on the aggregate properties of PDI multimers but also guide the further design of PDI-based organic photovoltaic solar cells.

Formation of Core-Shell AuCu@Ag Nanocrystals through the Nanoscale Kirkendall Effect.

Polymetallic nanocrystals (NCs) consist of multiple metal elements. A powerful platform to achieve the flexible construction of polymetallic NCs is highly desired but challenging. Herein, we devise a model system that realizes metal atom diffusion between different NCs, resulting in the formation of polymetallic NCs. The differential bond strength between different metal atoms is proposed to initiate such metal atom diffusion, and the specific high surface-to-volume ratio of the NCs can expedite the diffusion process. Taking the Au-Cu-Ag trimetallic system as an example, core-shell AuCu@Ag NCs were successfully formed by combining AgCu NCs with Au NCs. The evolution process was explored, and the gradual fusion of simple NCs into AuCu@Ag NCs was unambiguously observed, which could be attributed to the larger bond strength of Au-Cu than that of Ag-Cu. This work offers an opportunity/platform in theory and experiment to expand the synthesis framework as well as the polymetallic NC list.