RESUMEN
Fine-grained marine sediments containing veiny and nodular gas hydrates will evolve into fine-grained gassy sediments after hydrate dissociation due to climate-driven ocean warming. The mechanical properties of the fine-grained gassy sediments are basically acquired by ocean engineering design. However, they have not been fully understood, largely due to the lack of microstructure visualization. In this paper, a new system is developed to jointly conduct x-ray computed tomography scans, oedometer tests, and seismic wave testing on a single specimen with temperature being well controlled, allowing varieties of experimental data to be acquired effectively and automatically. The results show that stress history can hardly affect the undrained stiffness of fine-grained gassy sediments, while the drained stiffness of fine-grained sediments without gas bubbles is stress history dependent. After being unloaded, many microstructure changes remain, and examples include the free gas distribution being more concentrated and the connectivity among gas bubbles becoming much better. The multi-orientation system lays the foundation for further studies on the microstructure changes and mechanical responses of fine-grained gassy sediments associated with gas hydrates.
RESUMEN
The three-phase coexistence line of the CO2 hydrate was determined using molecular dynamics (MD) simulations. By using the classical and modified Lorentz-Berthelot (LB) parameters, the simulations were carried out at 10 different pressures from 3 to 500 MPa. For the OPC water model, simulations with the classic and the modified LB parameters both showed negative deviations from the experimental values. For the TIP4P/Ice water model, good agreement with experimental equilibrium data can be achieved when the LB parameter is adjusted based on the solubility of CO2 in water. Our results also show that the influence of the water model on the equilibrium prediction is much larger than the CO2 model. Current simulations indicated that the H2O-H2O and H2O-CO2 cross-interactions' parameters might contribute equally to the accurate prediction of T3. According to our simulations, the prediction of T3 values showed relatively higher accuracy while using the combination of TIP4P/Ice water and EPM2 CO2 with modified LB parameter. Furthermore, varied χ values are recommended for accurate T3 estimation over a wide pressure range. The knowledge obtained in this study will be helpful for further accurate MD simulation of the process of CO2/CH4 replacement.
RESUMEN
Clarifying the creep behaviors of hydrate-bearing sediment (HBS) under long-term loading is crucial for evaluating reservoir stability during hydrate exploitation. Figuring out a way of characterizing deformation behaviors and their geophysical responses to HBS is the basis for modeling creep behaviors. In this study, we propose a novel device to test time-dependent deformation and the ultrasonic response of HBS under high-pressure and low-temperature. The experimental device consists of a high-pressure chamber, an axial-load control system, a confining pressure system, a pore pressure system, a back-pressure system, and a data collection system. This testing assembly allows temperature regulation and independent control of four pressures, e.g., confining pressure, pore pressure, back pressure, and axial loading. Columned artificial HBS samples, with a diameter of 39 mm and a height of 120 mm, can be synthesized in this device. Afterward, in situ creep experiments can be achieved by applying stable confining pressure and axial load, together with geophysical signals acquisition. During loading, the stress-strain relationships and ultrasonic data can be obtained simultaneously. Through analyzing the stress-strain relationship and ultrasonic data, the macroscopical failure and microcosmical creep deformation law of the samples can be figured out. Preliminary experiments verified the applicability of the device. The method provides some significance for field observation of reservoir failure via geophysical techniques during hydrate exploitation.
RESUMEN
Natural gas hydrate has sparked worldwide interest due to its enormous energy potential. Geophysical surveys are commonly used in gas hydrate exploration, and resistivity logging plays an important role in this field. Nevertheless, the electrical response mechanism as a result of the gas hydrate growth in sediment is not well understood. This study develops an apparatus for the in situ resistivity testing of gas hydrate-bearing sediment combined with x-ray computed tomography scanning. Using this equipment, the gas hydrate samples can be synthesized under high-pressure and low-temperature conditions. The sample resistivities of three different layers can also be measured in situ during the gas hydrate formation. Moreover, x-ray computed tomography scanned gray images are acquired, which can be used to calculate the saturation and analyze the microscopic distribution of gas hydrate. A series of experiments are performed to validate the feasibility of the apparatus. The results show that the sample resistivity shows three distinct stages of variation as the gas hydrate grows. The most sensitive saturation range to the electrical response is â¼10.50%-22.34%. Very few gas hydrate particles will not significantly change the pore connectivity. By contrast, too many gas hydrate particles will hinder the pore network blocking. Both situations will not result in a significant change in resistivity.