ESTRO-ACROP guideline on surface guided radiation therapy.

Surface guidance systems enable patient positioning and motion monitoring without using ionising radiation. Surface Guided Radiation Therapy (SGRT) has therefore been widely adopted in radiation therapy in recent years, but guidelines on workflows and specific quality assurance (QA) are lacking. This ESTRO-ACROP guideline aims to give recommendations concerning SGRT roles and responsibilities and highlights common challenges and potential errors. Comprehensive guidelines for procurement, acceptance, commissioning, and QA of SGRT systems installed on computed tomography (CT) simulators, C-arm linacs, closed-bore linacs, and particle therapy treatment systems are presented that will help move to a consensus among SGRT users and facilitate a safe and efficient implementation and clinical application of SGRT.

Surface guided radiation therapy: An international survey on current clinical practice.

Introduction: Surface Guided Radiation Therapy (SGRT) is being increasingly implemented into clinical practice across a number of techniques and irradiation-sites. This technology, which is provided by different vendors, can be used with most simulation- and delivery-systems. However, limited guidelines and the complexity of clinical settings have led to diverse patterns of operation. With the aim to understand current clinical practice a survey was designed focusing on specifics of the clinical implementation and usage. Materials and methods: A 32-question survey covered: type and number of systems, quality assurance (QA), clinical workflows, and identification of strengths/limitations. Respondents from different professional groups and countries were invited to participate. The survey was distributed internationally via ESTRO-membership, social media and vendors. Results: Of the 278 institutions responding, 172 had at least one SGRT-system and 136 use SGRT clinically. Implementation and QA were primarily based on the vendors' recommendations and phantoms. SGRT was mainly implemented in breast RT (116/136), with strong but diverse representation of other sites. Many (58/135) reported at least partial elimination of skin-marks and a third (43/126) used open-masks. The most common imaging protocol reported included the combination of radiographic imaging with SGRT. Patient positioning (115/136), motion management (104/136) and DIBH (99/136) were the main applications.Main barriers to broader application were cost, system integration issues and lack of demonstrated clinical value. A lack of guidelines in terms of QA of the system was highlighted. Conclusions: This overview of the SGRT status has the potential to support users, vendors and organisations in the development of practices, products and guidelines.

The contact angle of nanofluids as thermophysical property.

Droplet volume and temperature affect contact angle significantly. Phase change heat transfer processes of nanofluids - suspensions containing nanometre-sized particles - can only be modelled properly by understanding these effects. The approach proposed here considers the limiting contact angle of a droplet asymptotically approaching zero-volume as a thermophysical property to characterise nanofluids positioned on a certain substrate under a certain atmosphere. Graphene oxide, alumina, and gold nanoparticles are suspended in deionised water. Within the framework of a round robin test carried out by nine independent European institutes the contact angle of these suspensions on a stainless steel solid substrate is measured with high accuracy. No dependence of nanofluids contact angle of sessile droplets on the measurement device is found. However, the measurements reveal clear differences of the contact angle of nanofluids compared to the pure base fluid. Physically founded correlations of the contact angle in dependency of droplet temperature and volume are obtained from the data. Extrapolating these functions to zero droplet volume delivers the searched limiting contact angle depending only on the temperature. It is for the first time, that this specific parameter, is understood as a characteristic material property of nanofluid droplets placed on a certain substrate under a certain atmosphere. Together with the surface tension it provides the foundation of proper modelling phase change heat transfer processes of nanofluids.

3D morphometric analysis of calcified cartilage properties using micro-computed tomography.

OBJECTIVE: Our aim is to establish methods for quantifying morphometric properties of calcified cartilage (CC) from micro-computed tomography (µCT). Furthermore, we evaluated the feasibility of these methods in investigating relationships between osteoarthritis (OA), tidemark surface morphology and open subchondral channels (OSCCs). METHOD: Samples (n = 15) used in this study were harvested from human lateral tibial plateau (n = 8). Conventional roughness and parameters assessing local 3-dimensional (3D) surface variations were used to quantify the surface morphology of the CC. Subchondral channel properties (percentage, density, size) were also calculated. As a reference, histological sections were evaluated using Histopathological osteoarthritis grading (OARSI) and thickness of CC and subchondral bone (SCB) was quantified. RESULTS: OARSI grade correlated with a decrease in local 3D variations of the tidemark surface (amount of different surface patterns (rs = -0.600, P = 0.018), entropy of patterns (EP) (rs = -0.648, P = 0.018), homogeneity index (HI) (rs = 0.555, P = 0.032)) and tidemark roughness (TMR) (rs = -0.579, P = 0.024). Amount of different patterns (ADP) and EP associated with channel area fraction (CAF) (rp = 0.876, P < 0.0001; rp = 0.665, P = 0.007, respectively) and channel density (CD) (rp = 0.680, P = 0.011; rp = 0.582, P = 0.023, respectively). TMR was associated with CAF (rp = 0.926, P < 0.0001) and average channel size (rp = 0.574, P = 0.025). CC topography differed statistically significantly in early OA vs healthy samples. CONCLUSION: We introduced a µ-CT image method to quantify 3D CC topography and perforations through CC. CC topography was associated with OARSI grade and OSCC properties; this suggests that the established methods can detect topographical changes in tidemark and CC perforations associated with OA.

In vitro method for 3D morphometry of human articular cartilage chondrons based on micro-computed tomography.

OBJECTIVE: The aims of this study were: to 1) develop a novel sample processing protocol to visualize human articular cartilage (AC) chondrons using micro-computed tomography (µCT), 2) develop and validate an algorithm to quantify the chondron morphology in 3D, and 3) compare the differences in chondron morphology between intact and osteoarthritic AC. METHOD: The developed protocol is based on the dehydration of samples with hexamethyldisilazane (HMDS), followed by imaging with a desktop µCT. Chondron density and depth, as well as volume and sphericity, were calculated in 3D with a custom-made and validated algorithm employing semi-automatic chondron selection and segmentation. The quantitative parameters were analyzed at three AC depth zones (zone 1: 0-10%; zone 2: 10-40%; zone 3: 40-100%) and grouped by the OARSI histological grades (OARSI grades 0-1.0, n = 6; OARSI grades 3.0-3.5, n = 6). RESULTS: After semi-automatic chondron selection and segmentation, 1510 chondrons were approved for 3D morphometric analyses. The chondrons especially in the deeper tissue (zones 2 and 3) were significantly larger (P < 0.001) and less spherical (P < 0.001), respectively, in the OARSI grade 3-3.5 group compared to the OARSI grade 0-1.0 group. No statistically significant difference in chondron density between the OARSI grade groups was observed at different depths. CONCLUSION: We have developed a novel sample processing protocol for chondron imaging in 3D, as well as a high-throughput algorithm to semi-automatically quantify chondron/chondrocyte 3D morphology in AC. Our results also suggest that 3D chondron morphology is affected by the progression of osteoarthritis (OA).

Electromechanical properties of human osteoarthritic and asymptomatic articular cartilage are sensitive and early detectors of degeneration.

OBJECTIVE: To evaluate cross-correlations of ex vivo electromechanical properties with cartilage and subchondral bone plate thickness, as well as their sensitivity and specificity regarding early cartilage degeneration in human tibial plateau. METHOD: Six pairs of tibial plateaus were assessed ex vivo using an electromechanical probe (Arthro-BST) which measures a quantitative parameter (QP) reflecting articular cartilage compression-induced streaming potentials. Cartilage thickness was then measured with an automated thickness mapping technique using Mach-1 multiaxial mechanical tester. Subsequently, a visual assessment was performed by an experienced orthopedic surgeon using the International Cartilage Repair Society (ICRS) grading system. Each tibial plateau was finally evaluated with µCT scanner to determine the subchondral-bone plate thickness over the entire surface. RESULTS: Cross-correlations between assessments decreased with increasing degeneration level. Moreover, electromechanical QP and subchondral-bone plate thickness increased strongly with ICRS grade (ρ = 0.86 and ρ = 0.54 respectively), while cartilage thickness slightly increased (ρ = 0.27). Sensitivity and specificity analysis revealed that the electromechanical QP is the most performant to distinguish between different early degeneration stages, followed by subchondral-bone plate thickness and then cartilage thickness. Lastly, effect sizes of cartilage and subchondral-bone properties were established to evaluate whether cartilage or bone showed the most noticeable changes between normal (ICRS 0) and each early degenerative stage. Thus, the effect sizes of cartilage electromechanical QP were almost twice those of the subchondral-bone plate thickness, indicating greater sensitivity of electromechanical measurements to detect early osteoarthritis. CONCLUSION: The potential of electromechanical properties for the diagnosis of early human cartilage degeneration was highlighted and supported by cartilage thickness and µCT assessments.

Regioselective thioacetylation of chitosan end-groups for nanoparticle gene delivery systems.

Chitosan (CS) end-group chemistry is a conjugation strategy that has been minimally exploited in the literature to date. Although the open-chain form of the CS reducing extremity bears a reactive aldehyde moiety, the most common method to generate a reactive end-group on CS is nitrous acid depolymerization, which produces a 2,5-anhydro-d-mannose unit (M-Unit) bearing also an aldehyde moiety. However, the availability of the latter might be low, since previous literature suggests that its hydrated and non-reactive form, namely the gem-diol form, is predominant in acidic aqueous conditions. Oxime-click chemistry has been used to react on such aldehydes with various degrees of success, but the use of a co-solvent and additional chemical reagents remain necessary to obtain the desired and stable covalent linkage. In this study, we have assessed the availability of the aldehyde reactive form on chitosan treated with nitrous acid. We have also assessed its reactivity towards thiol-bearing molecules in acidic conditions where CS amino groups are fully protonated and thus unreactive towards aldehyde. LC-MS and NMR spectroscopy methods (1H and DOSY, respectively) confirmed the regioselective thioacetylation of the reactive aldehyde with conversion rates between 55 and 70% depending on the thiol molecule engaged. The stabilization of the hemithioacetal intermediates into the corresponding thioacetals was also found to be facilitated upon freeze-drying of the reaction medium. The PEGylation of the CS M-Unit aldehyde by thioacetylation was also performed as a direct application of the proposed conjugation approach. CS-b-PEG2 block copolymers were successfully synthesized and were used to prepare block ionomer complexes with plasmid DNA, as revealed by their spherical morphology vs. the rod-like/globular/toroidal morphology observed for polyplexes prepared using native unmodified chitosan. This novel aqueous thiol-based conjugation strategy constitutes an alternative to the oxime-click pathway; it could be applicable to other polymers.

Extracellular matrix mineralization in murine MC3T3-E1 osteoblast cultures: an ultrastructural, compositional and comparative analysis with mouse bone.

Bone cell culture systems are essential tools for the study of the molecular mechanisms regulating extracellular matrix mineralization. MC3T3-E1 osteoblast cell cultures are the most commonly used in vitro model of bone matrix mineralization. Despite the widespread use of this cell line to study biomineralization, there is as yet no systematic characterization of the mineral phase produced in these cultures. Here we provide a comprehensive, multi-technique biophysical characterization of this cell culture mineral and extracellular matrix, and compare it to mouse bone and synthetic apatite mineral standards, to determine the suitability of MC3T3-E1 cultures for biomineralization studies. Elemental compositional analysis by energy-dispersive X-ray spectroscopy (EDS) showed calcium and phosphorus, and trace amounts of sodium and magnesium, in both biological samples. X-ray diffraction (XRD) on resin-embedded intact cultures demonstrated that similar to 1-month-old mouse bone, apatite crystals grew with preferential orientations along the (100), (101) and (111) mineral planes indicative of guided biogenic growth as opposed to dystrophic calcification. XRD of crystals isolated from the cultures revealed that the mineral phase was poorly crystalline hydroxyapatite with 10 to 20nm-sized nanocrystallites. Consistent with the XRD observations, electron diffraction patterns indicated that culture mineral had low crystallinity typical of biological apatites. Fourier-transform infrared spectroscopy (FTIR) confirmed apatitic carbonate and phosphate within the biological samples. With all techniques utilized, cell culture mineral and mouse bone mineral were remarkably similar. Scanning (SEM) and transmission (TEM) electron microscopy showed that the cultures had a dense fibrillar collagen matrix with small, 100nm-sized, collagen fibril-associated mineralization foci which coalesced to form larger mineral aggregates, and where mineralized sites showed the accumulation of the mineral-binding protein osteopontin. Light microscopy, confocal microscopy and three-dimensional reconstructions showed that some cells had dendritic processes and became embedded within the mineral in an osteocyte-like manner. In conclusion, we have documented characteristics of the mineral and matrix phases of MC3T3-E1 osteoblast cultures, and have determined that the structural and compositional properties of the mineral are highly similar to that of mouse bone.

Non-destructive electromechanical assessment (Arthro-BST) of human articular cartilage correlates with histological scores and biomechanical properties.

OBJECTIVE: The hand-held Arthro-BST™ device is used to map electromechanical properties of articular cartilage. The purpose of the study was to evaluate correlation of electromechanical properties with histological, biochemical and biomechanical properties of cartilage. METHOD: Electromechanical properties (quantitative parameter (QP)) of eight human distal femurs were mapped manually ex vivo using the Arthro-BST (1 measure/site, 5 s/measure, 3209 sites). Osteochondral cores were then harvested from different areas on the femurs and assessed with the Mankin histological score. Prior to histoprocessing, cores were tested in unconfined compression. A subset of the cores was analyzed with polarized light microscopy (PLM) to assess collagen structure. Biochemical assays were done on additional cores to obtain water content and glycosaminoglycan (GAG) content. The QP corresponding to each core was calculated by averaging all QPs collected within 6 mm of the core center. RESULTS: The electromechanical QP correlated strongly with both the Mankin score and the PLM score (r = 0.73, P < 0.0001 and r = -0.70, P < 0.0001 respectively) thus accurately reflecting tissue quality and collagen architecture. Electromechanical QP also correlated strongly with biomechanical properties including fibril modulus (r = -0.76, P < 0.0001), matrix modulus (r = -0.69, P < 0.0001), and log of permeability (r = 0.72, P < 0.0001). The QP correlated weakly with GAG per wet weight and with water content (r = -0.50, P < 0.0003 and r = 0.39, P < 0.006 respectively). CONCLUSION: Non-destructive electromechanical QP measurements correlate strongly with histological scores and biomechanical parameters providing a rapid and reliable assessment of articular cartilage quality.

Electroarthrography: a novel method to assess articular cartilage and diagnose osteoarthritis by non-invasive measurement of load-induced electrical potentials at the surface of the knee.

OBJECTIVE: A new technique called electroarthrography (EAG) measures electrical potentials on the surface of the knee during joint loading. The objective of this study was to evaluate the effectiveness of EAG to assess joint cartilage degeneration. DESIGN: EAG recordings were performed on 20 asymptomatic subjects (Control group) and on 20 patients with bilateral knee osteoarthritis (OA) who had had a unilateral total knee replacement (TKR), both the TKR knee and the remaining knee were analyzed. EAG signals were recorded at eight electrode sites over one knee as the subjects shifted their weight from one leg to the other to achieve joint loading. The EAG signals were filtered, baseline-corrected and time-averaged. RESULTS: EAG repeatability was assessed with a test-retest protocol which showed statistically significant high intraclass correlation coefficients (ICC) for four electrode sites near the joint line. These sites also showed the highest mean EAG values. The mean EAG potentials of the Control group were significantly higher compared with the OA group for three sites overlying the joint line. The potentials overlying the TKR were statistically nul. In the Control group, no statistically significant correlation was found between the EAG amplitude and age, weight, height or body mass index (BMI); no statistical difference was found in mean EAG potentials between women and men. CONCLUSIONS: This study indicates that EAG signals arise from the streaming potentials in compressed articular cartilage which are known sensitive indicators of joint cartilage health. EAG is a promising new technique for the non-invasive assessment of cartilage degeneration and arthritis.

Indocyanine green-augmented diode laser therapy vs. long-pulsed Nd:YAG (1064 nm) laser treatment of telangiectatic leg veins: a randomized controlled trial.

BACKGROUND: Telangiectatic leg veins (TLV) represent a common cosmetic problem. Near infrared lasers have been widely used in treatment because of their deeper penetration into the dermis, but with varying degrees of success, particularly because of different vessel diameters. Indocyanine green (ICG)-augmented diode laser treatment (ICG+DL) may present an alternative treatment option. OBJECTIVES: This trial evaluates the efficacy of ICG+DL in the treatment of TLV and compares the safety and efficacy of therapy with the standard treatment, the long-pulsed neodymium-doped yttrium aluminium garnet (Nd:YAG) laser. METHODS: In a prospective randomized controlled clinical trial, 29 study participants with TLV were treated with a Nd:YAG laser (λem = 1064 nm, 160-240 J cm(-2) , 65-ms pulse duration, 5-mm spot size) and ICG+DL (λem = 810 nm, 60-110 J cm(-2) , 48-87-ms pulse duration, 6-mm spot size; total ICG dose 4 mg kg(-1) ) in a side-by-side comparison in one single treatment setting that included histological examination in four participants. Two blinded investigators and the participants assessed clearance rate, cosmetic appearance and adverse events up to 3 months after treatment. RESULTS: According to both the investigators' and participants' assessment, clearance rates were significantly better after ICG+DL therapy than after Nd:YAG laser treatment (P < 0·05). On a 10-point scale indicating pain during treatment, participants rated ICG+DL therapy to be more painful (6·1 ± 2·0) than Nd:YAG laser (5·4 ± 2·0). CONCLUSIONS: ICG+DL therapy represents a new and promising treatment modality for TLV, with high clearance rates and a very good cosmetic outcome after one single treatment session.

Bone marrow stimulation induces greater chondrogenesis in trochlear vs condylar cartilage defects in skeletally mature rabbits.

OBJECTIVE: The aim of this study was to compare the early repair response of cartilage defects in trochlea (TR) and medial femoral condyle (MFC) at 2-3 weeks after bone marrow stimulation. DESIGN: Bilateral full-thickness cartilage defects were generated in central trochlear groove and MFC of skeletally mature rabbits. Four subchondral perforations were made on each defect, either by microfracture to 2 mm deep, or by drilling to 2 mm or 6 mm deep. Rabbits were sacrificed either on Day 14 post-operatively or on Day 21. Defects were analyzed by histology, stereology, histomorphometry and micro-computed tomography (CT). Intact femurs (N = 4) served as controls. RESULTS: Stromal cell density recruitment was similar in all defects, irrespective of defect location and surgical techniques used. There was a robust appearance of chondrocytes at Day 21 in TR defects with significantly higher volume fraction of chondrocytes in TR compared to MFC (P = 0.013). Chondrogenic foci were observed in marrow penetrating holes, with a significantly higher frequency and larger foci in TR vs MFC defects at Day 21 (P = 0.043 and P = 0.0014, respectively). Micro-CT analysis showed that deep drilling elicited significantly more mineralized bone fill compared to shallower perforations at 2 and 3 weeks repair (all at P ≤ 0.0008). CONCLUSIONS: Bone marrow stimulation induced greater chondrogenesis in TR vs MFC defects in adult rabbits, with more chondrocytes and larger chondrogenic foci appearing in TR vs MFC on Day 21 post-operation.

Partial meniscectomy changes fluid pressurization in articular cartilage in human knees.

Partial meniscectomy is believed to change the biomechanics of the knee joint through alterations in the contact of articular cartilages and menisci. Although fluid pressure plays an important role in the load support mechanism of the knee, the fluid pressurization in the cartilages and menisci has been ignored in the finite element studies of the mechanics of meniscectomy. In the present study, a 3D fibril-reinforced poromechanical model of the knee joint was used to explore the fluid flow dependent changes in articular cartilage following partial medial and lateral meniscectomies. Six partial longitudinal meniscectomies were considered under relaxation, simple creep, and combined creep loading conditions. In comparison to the intact knee, partial meniscectomy not only caused a substantial increase in the maximum fluid pressure but also shifted the location of this pressure in the femoral cartilage. Furthermore, these changes were positively correlated to the size of meniscal resection. While in the intact joint, the location of the maximum fluid pressure was dependent on the loading conditions, in the meniscectomized joint the location was predominantly determined by the site of meniscal resection. The partial meniscectomy also reduced the rate of the pressure dissipation, resulting in even larger difference between creep and relaxation times as compared to the case of the intact knee. The knee joint became stiffer after meniscectomy because of higher fluid pressure at knee compression followed by slower pressure dissipation. The present study indicated the role of fluid pressurization in the altered mechanics of meniscectomized knees.

Structural characteristics of the collagen network in human normal, degraded and repair articular cartilages observed in polarized light and scanning electron microscopies.

OBJECTIVE: This study characterizes collagen organization (CO) in human normal (n = 6), degraded (n = 6) and repair (n = 22) cartilages, using polarized light (PLM) and scanning electron (SEM) microscopies. DESIGN: CO was assessed using a recently developed PLM-CO score (Changoor et al. Osteoarthritis Cartilage 2011;19:126-35), and zonal proportions measured. SEM images were captured from locations matched to PLM. Fibre orientations were assessed in SEM and compared to those observed in PLM. CO was also assessed in individual SEM images and combined to generate a SEM-CO score for overall CO analogous to PLM-CO. Fibre diameters were measured in SEM. RESULTS: PLM-CO and SEM-CO scores were correlated, r = 0.786 (P < 0.00001, n = 32), after excluding two outliers. Orientation observed in PLM was validated by SEM since PLM/SEM correspondence occurred in 91.6% of samples. Proportions of the deep (DZ), transitional (TZ) and superficial (SZ) zones averaged 74.0 ± 9.1%, 18.6 ± 7.0%, and 7.3 ± 1.2% in normal, and 45.6 ± 10.7%, 47.2 ± 10.1% and 9.5 ± 3.4% in degraded cartilage, respectively. Fibre diameters in normal cartilage increased with depth from the articular surface [55.8 ± 9.4 nm (SZ), 87.5 ± 1.8 nm (TZ) and 108.2 ± 1.8 nm (DZ)]. Fibre diameters were smaller in repair biopsies [60.4 ± 0.7 nm (SZ), 63.2 ± 0.6 nm (TZ) and 67.2 ± 0.8 nm (DZ)]. Degraded cartilage had wider fibre diameter ranges and bimodal distributions, possibly reflecting new collagen synthesis and remodelling or collagen fibre unravelling. Repair tissues revealed the potential of microfracture-based repair procedures to produce zonal CO resembling native articular cartilage structure. Values are reported as mean ± 95% confidence interval. CONCLUSION: This detailed assessment of collagen architecture could benefit the development of cartilage repair strategies intended to recreate functional collagen architecture.

Streaming potential-based arthroscopic device is sensitive to cartilage changes immediately post-impact in an equine cartilage injury model.

Models of post-traumatic osteoarthritis where early degenerative changes can be monitored are valuable for assessing potential therapeutic strategies. Current methods for evaluating cartilage mechanical properties may not capture the low-grade cartilage changes expected at these earlier time points following injury. In this study, an explant model of cartilage injury was used to determine whether streaming potential measurements by manual indentation could detect cartilage changes immediately following mechanical impact and to compare their sensitivity to biomechanical tests. Impacts were delivered ex vivo, at one of three stress levels, to specific positions on isolated adult equine trochlea. Cartilage properties were assessed by streaming potential measurements, made pre- and post-impact using a commercially available arthroscopic device, and by stress relaxation tests in unconfined compression geometry of isolated cartilage disks, providing the streaming potential integral (SPI), fibril modulus (Ef), matrix modulus (Em), and permeability (k). Histological sections were stained with Safranin-O and adjacent unstained sections examined in polarized light microscopy. Impacts were low, 17.3 ± 2.7 MPa (n = 15), medium, 27.8 ± 8.5 MPa (n = 13), or high, 48.7 ± 12.1 MPa (n = 16), and delivered using a custom-built spring-loaded device with a rise time of approximately 1 ms. SPI was significantly reduced after medium (p = 0.006) and high (p<0.001) impacts. Ef, representing collagen network stiffness, was significantly reduced in high impact samples only (p < 0.001 lateral trochlea, p = 0.042 medial trochlea), where permeability also increased (p = 0.003 lateral trochlea, p = 0.007 medial trochlea). Significant (p < 0.05, n = 68) moderate to strong correlations between SPI and Ef (r = 0.857), Em (r = 0.493), log(k) (r = -0.484), and cartilage thickness (r = -0.804) were detected. Effect sizes were higher for SPI than Ef, Em, and k, indicating greater sensitivity of electromechanical measurements to impact injury compared to purely biomechanical parameters. Histological changes due to impact were limited to the presence of superficial zone damage which increased with impact stress. Non-destructive streaming potential measurements were more sensitive to impact-related articular cartilage changes than biomechanical assessment of isolated samples using stress relaxation tests in unconfined compression geometry. Correlations between electromechanical and biomechanical methods further support the relationship between non-destructive electromechanical measurements and intrinsic cartilage properties.

Creep behavior of the intact and meniscectomy knee joints.

The mechanical functions of the menisci may be partially performed through the fluid pressurization in articular cartilages and menisci. This creep behavior has not been investigated in whole knee joint modeling. A three-dimensional finite element knee model was employed in the present study to explore the fluid-flow dependent creep behaviors of normal and meniscectomy knees. The model included distal femur, tibia, fibula, articular cartilages, menisci and four major ligaments. Articular cartilage or meniscus was modeled as a fluid-saturated solid matrix reinforced by a nonlinear orthotropic and site-specific collagen network. A 300 N compressive force, equal to half of body weight, was applied to the knee in full extension followed by creep. The results showed that the fluid pressurization played a substantial role in joint contact mechanics. Menisci bore more loading as creep developed, leading to decreased stresses in cartilages. The removal of menisci not only changed the stresses in the cartilages, which was in agreement with published studies, but also altered the distribution and the rate of dissipation of fluid pressure in the cartilages. The high fluid pressures in the femoral cartilage moved from anterior to more central regions of the condyles after total meniscectomy. For both intact and meniscectomy joints, the fluid pressure level remained considerably high for thousands of seconds during creep, which lasted even longer after meniscectomy. For the femoral cartilage, the maximum principal stress was generally in agreement with the fiber direction, which indicated the essential role of fibers in load support of the tissue.

Effective and safe gene-based delivery of GLP-1 using chitosan/plasmid-DNA therapeutic nanocomplexes in an animal model of type 2 diabetes.

Glucagon-like peptide-1 (GLP-1) is an incretin hormone that regulates blood glucose level post-prandially. It has been proposed that GLP-1 can be used in type 2 diabetes (T2D) mellitus treatment because of its insulinotropic action. Despite its remarkable advantages, GLP-1 suffers the disadvantage of an extremely short half-life owing to its degradation by the dipeptidyl peptidase IV protease. One way of overcoming this drawback is GLP-1 gene delivery. Here we show effective and safe gene-based delivery of GLP-1 using chitosan/plasmid-DNA therapeutic nanocomplexes (TNCs) in Zucker diabetic fatty (ZDF) animal model of T2D. The expression plasmid fused the GLP-1 gene to a Furin cleavage site was driven by a cytomegalovirus promoter/enhancer. TNCs were prepared by mixing this plasmid with chitosans of specific molecular weight (MW), degree of deacetylation (DDA) and ratio of chitosan amine to DNA phosphate (N:P ratio). Animals injected with the TNC chitosan 92-10-5 (DDA-MW-N:P) showed GLP-1 plasma levels of about fivefold higher than that in non-treated animals and the insulinotropic effect of recombinant GLP-1 was shown by a threefold increase in plasma insulin concentration when compared with untreated animals. Intraperitoneal glucose tolerance tests revealed an efficacious decrease of blood glucose compared with controls for up to 24 days after treatment, where injections of this formulation allowed near-normalization of blood glucose level. TNCs composed of specific chitosans and GLP-1-expressing plasmid constructs showed an impressive ability to harness the profound therapeutic potential of GLP-1 for the treatment of T2D mellitus.

A polarized light microscopy method for accurate and reliable grading of collagen organization in cartilage repair.

OBJECTIVES: Collagen organization, a feature that is critical for cartilage load bearing and durability, is not adequately assessed in cartilage repair tissue by present histological scoring systems. Our objectives were to develop a new polarized light microscopy (PLM) score for collagen organization and to test its reliability. DESIGN: This PLM score uses an ordinal scale of 0-5 to rate the extent that collagen network organization resembles that of young adult hyaline articular cartilage (score of 5) vs a totally disorganized tissue (score of 0). Inter-reader reliability was assessed using Intraclass Correlation Coefficients (ICC) for Agreement, calculated from scores of three trained readers who independently evaluated blinded sections obtained from normal (n=4), degraded (n=2) and repair (n=22) human cartilage biopsies. RESULTS: The PLM score succeeded in distinguishing normal, degraded and repair cartilages, where the latter displayed greater complexity in collagen structure. Excellent inter-reader reproducibility was found with ICCs for Agreement of 0.90 [ICC(2,1)] (lower boundary of the 95% confidence interval is 0.83) and 0.96 [ICC(2,3)] (lower boundary of the 95% confidence interval is 0.94), indicating the reliability of a single reader's scores and the mean of all three readers' scores, respectively. CONCLUSION: This PLM method offers a novel means for systematically evaluating collagen organization in repair cartilage. We propose that it be used to supplement current gold standard histological scoring systems for a more complete assessment of repair tissue quality.

Temporal and spatial modulation of chondrogenic foci in subchondral microdrill holes by chitosan-glycerol phosphate/blood implants.

OBJECTIVE: Subchondral drilling initiates a cartilage repair response involving formation of chondrogenic foci in the subchondral compartment. The purpose of this study was to structurally characterize these sites of chondrogenesis and to investigate the effects of chitosan-glycerol phosphate (GP)/blood implants on their formation. METHOD: Thirty-two New Zealand White rabbits received bilateral cartilage defects bearing four subchondral drill holes. One knee per rabbit was treated by solidifying a chitosan-GP/blood implant over the defect. After 1-56 days of repair, chondrogenic foci were characterized by histostaining and immunostaining. Collagen fiber orientation was characterized by polarized light microscopy. RESULTS: Glycosaminoglycan and collagen type II were present throughout the foci while the upper zone expressed collagen type I and the lower zone collagen type X. Large chondrogenic foci had a stratified structure with flatter cells closer to the articular surface, and round or hypertrophic chondrocytes deeper in the drill holes that showed signs of calcification after 3 weeks of repair in control defects. Markers for pre-hypertrophic chondrocytes (Patched) and for proliferation (Ki-67) were detected within foci. Some cells displayed a columnar arrangement where collagen was vertically oriented. For treated defects, chondrogenic foci appeared 1-3 weeks later, foci were nascent and mature rather than resorbing, and foci developed closer to the articular surface. CONCLUSIONS: Chondrogenic foci bear some similarities to growth cartilage and can give rise to a repair tissue that has similar zonal stratification as articular cartilage. The temporal and spatial formation of chondrogenic foci can be modulated by cartilage repair therapies.