RESUMEN
The configuration of implant-supported prostheses is considered to influence the magnitude of stress concentrations, affecting their survival rate. The purpose of this study is to determine, through strain gauge measurements during load application, the dispersion and magnitude of strain concentrations in different implant-supported prosthesis designs. All designs matched those commonly used in posterior partially edentulous states. Three implants were inserted into an epoxy resin model (PLM-4B Vishay Measurements Group Inc., Raleigh, NC, USA), allowing for the delivery of three- and four-unit crowns in different cemented configurations. Loads were applied at vertical and oblique directions over the cast crowns in six different configurations representing various posterior partially edentulous restorations. The readings from the strain gauges adhered to the implant necks' presented data on implant strain. Prostheses including cantilevers showed the highest strain among the three-unit prostheses within the prosthetic complex, and three single units showed the least (8133 µs vs. 201 µs, respectively). Angulated load application also had a role in amplifying the strains recorded, resulting in total strains of between 3.5 and 20 times higher than during vertical loading in all configurations. It can be concluded that the configuration of implant-fixed partial prosthesis changes the loads engaging the restoration, the implant, and, probably, the supporting bone.
RESUMEN
Objectives To evaluate and compare bacterial growth on zirconia versus titanium healing caps. Material and methods S. sanguinis (Ss) and F. nucleatum (Fn) were grown on titanium and zirconia healing caps that were fixed to the cover of a 96-well microtiter plate. A drop (10 µL) of bacterial suspension was placed on each healing cap and allowed to dry for 1h at 37°C. After this time, the cover was replaced on the plate such that the caps were completely immersed in fresh liquid medium. Each plate contained only one bacterial strain, with 2 control groups. Bacterial growth was monitored over 18h by following the optical density at 650nm. A one-way ANOVA comparison test was used for statistical analysis. Scanning electron microscope (SEM) images of healing caps of each material were taken after a 48h incubation with Ss or Fn to assess bacterial attachment and with no bacteria as control. Results Ss growth was similar in both types of healing cap with no significant differences between these groups and the control (P=0.990). However, there was significantly less growth of Fn on the zirconia caps than on the titanium samples (P<0.0001) or the control (P<0.0001). SEM imaging revealed obvious differences in the surface characteristics of the titanium and zirconia caps. The number of bacteria attached to the rough apical area was particularly high. Conclusions The use of zirconia healing caps may reduce the growth of some bacterial species compared to that seen on titanium healing caps.
RESUMEN
OBJECTIVE: A re-pneumatization phenomenon was recorded in sinuses grafted with different materials. The specific aims of this paper were to assess the dental implant survival rate and the behavior of marginal and apical bone remodeling around dental implants placed following sinus augmentation. MATERIALS AND METHODS: A retrospective study was conducted on consecutive patients treated in two surgical centers. Different surgical techniques were adopted for sinus augmentation: simultaneous or delayed dental implant insertion with bovine bone-material augmentation or autologous bone grafting (chin and iliac crest). Survival rates were recorded for the overall number of implants (patients of group A). Apical and marginal bone levels (ABL and MBL, respectively) were radiographically measured, and statistical analysis was performed in implants of a subgroup of patients (group B). RESULTS: A total of 282 dental implants were positioned. Recorded cumulative survival rates (CSRs) were 95.6% and 100% for autogenous and bovine bone material, respectively, while CSRs at 2-year follow-up for immediate and delayed procedures were 99.3% and 96.5%. For the subgroup B, 57 sinus augmentation procedures were performed in 39 patients, with the positioning of 154 implants. Generally, the apical- and marginal-bone resorption of the bovine bone-material group was less than that of the autogenous group. The differences between the ABL values of the bovine bone-material and iliac-crest groups were statistically significant at 1 year, whereas this significance disappeared at the 2-year follow-up; tests showed that a statistical difference was recorded in the bovine bone-material group between the 1- and 2-year follow-ups. With regard to MBL comparisons between simultaneous and delayed implantation, the differences maintained their significance at the 2-year follow-up also. CONCLUSIONS: Differences regarding apical bone alteration between autogenous bone from the iliac crest and bovine bone material at the 1- and 2-year follow-ups, as well as in the bovine bone-material group between the 1- and 2-year follow-ups, attested to slower but more prolonged physiologic bone remodeling in the bovine-graft-material group than in the autogenous-bone group. The MBL analysis showed that remodeling in the delayed implant group demonstrated a greater resorption in the cervical portion than was seen in the simultaneous implant group.