Clinical performance of bonded partial lithium disilicate restorations: The influence of preparation characteristics on survival and success.

OBJECTIVES: The aim of this study was to investigate the influence of preparation characteristics on the survival, success, and clinical performance of partial indirect lithium disilicate restorations with immediate dentin sealing. METHODS: This retrospective clinical study evaluated partial indirect lithium disilicate restorations placed in conjunction with Immediate Dentin Sealing (IDS) in (pre)molar teeth between March 2018 and May 2021. The restorations were luted using pre-heated composite. The study focused on survival, success, and clinical performance, which was evaluated using the modified United States Public Health Service (USPHS) criteria. Results were analyzed using the Kaplan-Meier estimates, log-rank tests, and Fisher exact tests. RESULTS: Partial indirect lithium disilicate restorations (N = 454) were evaluated in 214 patients. The mean evaluation time was 37 months, with a cumulative survival rate of 99.2 % and a cumulative success rate of 97.6 %. Fourteen failures occurred, with endodontic pathology as the predominant failure mode, followed by secondary caries, debonding, and tooth fracture. No statistically significant influence of the preparation variables on survival and success was observed (p > .05). The short-term clinical performance was clinically acceptable in > 90 % of the evaluations. CONCLUSIONS: This retrospective study on partial indirect lithium disilicate restorations in conjunction with IDS demonstrates survival and success rates of 99.2 and 96.7 % over a mean evaluation period of 37 months. A marked influence of the studied preparation characteristics on the survival, success and clinical performance of lithium disilicate partial restorations could not be demonstrated. Partial lithium disilicate restorations exhibit good clinical performance in >90 % of the cases. CLINICAL SIGNIFICANCE: The results of this study suggest that preparation characteristics had no significant impact on the survival, success, and clinical performance of partial lithium disilicate restorations in conjunction with IDS. Results show good clinical performance and high survival and success rates, regardless of preparation characteristics.

Adhesion of resin cement to dentin: effects of adhesive promoters, immediate dentin sealing strategies, and surface conditioning.

PURPOSE: This study evaluated the shear bond strength (SBS) of resin cement to dentin after applying two adhesive (A) systems with a combination of four different immediate dentin sealing (IDS) strategies, and two surface conditioning (SC) methods. MATERIAL AND METHODS: Human third molars (n = 140) were collected and randomly split (n = 70 each) between the two A systems (Clearfil SE Bond; Kuraray [AC] and Optibond FL; Kerr [AO]). The A groups were further divided into four IDS strategies (2 x one adhesive layer (IDS-1L); 2 x two adhesive layers (IDS-2L); 2 x one adhesive layer and one flowable layer (IDS-F); 2 x no adhesive layer (delayed dentin sealing [DDS]). Finally, each strategy group was categorized into one of the two SC methods (only pumice [SC-P] or pumice and silica coating [SC-PS]), except the DDS group, where only SC-P was used. This resulted in 14 groups of 10 specimens each. The occlusal coronal third was removed from each molar crown with a diamond saw (Isomet 1000), and IDS was applied, followed by temporary restorations. These were removed after 2 weeks of water storage, and the IDS surfaces were subsequently conditioned. The standard adhesive procedure (Syntac Primer and Adhesive, Heliobond; Ivoclar Vivadent) was executed, followed by the application of a resin cement (Variolink II; Ivoclar Vivadent) and photopolymerization. All specimens were subjected to thermocyclic aging (10,000 cycles, 5°C to 55°C). Shear force was applied to the adhesive interface in a universal testing machine (1 mm/min). Fracture types and locations after loading were classified. The data were analyzed using analysis of variance (ANOVA) and independent samples t tests. RESULTS: AO groups exhibited higher mean SBS values (14.4 ± 6.43) than AC groups (12.85 ± 4.97) (P = 0.03). ANOVA showed the main effect of the applications on the SBS in the different groups (P = 0.00). Both DDS groups showed significantly lower SBS values compared with all the IDS groups (IDS-1L, IDS-2L, IDS-F). No significant differences in SBS results were found between the IDS groups (P = 0.43) and between the SC methods (P = 0.76). Dentin-cement interface failures diminished with the application of IDS. CONCLUSION: IDS improves the SBS compared with DDS. No significant differences were found between the tested conditioning methods.

Loss of Accuracy of Torque Wrenches Due to Clinical Use and Cleaning Procedure: Short Communication.

PURPOSE: The aim of this study was to investigate the way intensive use and multiple cleanings of torque wrenches may interfere with accurary over time. MATERIALS AND METHODS: Three different brands (one spring-style and two friction-style types) were tested at baseline and after enduring mechanical testing (1,000 cycles) and cleaning in a thermal disinfector (150 cycles). Torque wrenches were tested at a predetermined value of 30 Ncm at given intervals, and true values were registered by means of a digital torque gauge. RESULTS: All measured values varied between 28.3 Ncm and 31.1 Ncm. Only the spring-style torque wrench revealed values that differed significantly from baseline after both mechanical testing (P < .001) and cleaning (P < .05). CONCLUSION: The spring-style torque wrench produced values that changed significantly after multiple mechanical and multiple cleaning cycles. However, the differences were small and the measured values from all tested specimens were close to the predetermined value of 30 Ncm.