Investigation of use of hydrophilic/hydrophobic NADESs for selective extraction of As(III) and Sb(III) ions in vegetable samples: Air assisted liquid phase microextraction and chemometric optimization.

In this paper, a green, cost-effective sample preparation method based on air assisted liquid phase microextraction (AA-LPME) was developed for the simultaneous extraction of As(III) and Sb(III) ions from vegetable samples using hydrophilic/hydrophobic natural deep eutectic solvents (NADESs). Central composite design was used for the optimization of extraction factors including NADES volume, extraction cycle, pH, and curcumin concentration. Limits of detection for As(III) and Sb(III) were 1.5 ng L-1 and 0.06 ng L-1, respectively. Working ranges for As(III) and Sb(III) were 0.2-300 ng L-1 (coefficient of determination (R2 = 0.9978) and 5-400 ng L-1 (R2 = 0.9996), respectively. Relative standard deviations for As(III) and Sb(III) were 2.2-2.8% and 2.9-3.2%, respectively. Enrichment factor of the method was 184 for As(III) and 172 for Sb(III). The accuracy and precision of the AA-NADES-LPME method were investigated by intraday/interday studies and standard reference material analysis, respectively. Finally, the AA-NADES-LPME method was successfully applied to microwave digested vegetable samples using the standard addition approach and acceptable recoveries were achieved.

An air-assisted dispersive liquid phase microextraction method based on a hydrophobic magnetic deep eutectic solvent for the extraction and preconcentration of melamine from milk and milk-based products.

In the current research, a fast and sustainable air-assisted hydrophobic magnetic deep eutectic solvent-based dispersive liquid phase microextraction followed by UV-Vis spectrophotometry measurements was optimized for the extraction and determination of melamine in milk and milk-based products. The central composite design was applied for the optimization of factors affecting the recovery of melamine. Quantitative extraction of melamine was achieved using hydrophobic magnetic deep eutectic solvents prepared from a mixture of octanoic acid, aliquat-336, and cobalt(II) chloride. The optimum conditions for extraction were found as follows: 6 extraction cycles, pH 8.2, extraction solvent volume 260 µL, and acetone volume 125 µL.Interestingly, a centrifugation step was not required to achieve phase separation. Under the optimum conditions, melamine was determined in the linear range of 3-600 ng mL-1, the limit of detection (3Sblank/m) of 0.9 ng mL-1, and the enrichment factor of 144. The validation of the method was investigated by the analysis of reference materials. Consequently, the method was successfully applied for the analysis of melamine residues in milk and milk-based products.

Solar light driven degradation of textile dye contaminants for wastewater treatment - studies of novel polycationic selenide photocatalyst and process optimization by response surface methodology desirability factor.

The unplanned anthropogenic activities and raced industrial revolution detrimentally causes serious threat to terrestrial and aquatic life. A high discharge of wastewater from industries using dyes affects living organisms and the environment. This paper presents studies on polycationic selenides (PCS) synthesized by hydrothermal methods for photocatalytic degradation of dyes. The synthesized PCS were confirmed by various characterization techniques such as FTIR, SEM, EDX, UV/Vis, and XRD. The FTIR spectra revealed characteristic band at 843, 548 cm-1, and 417 cm-1 due to the M - Se stretching and intrinsic stretching vibrations, respectively. The optical bandgap of polycationic selenide lies in the visible light region (2.36 eV). The SEM images showed that PCS has a spherical shape with an average crystallite size of 29.23 nm calculated from XRD data using Scherer's equation. The PCS has a point of zero charge (PZC) at pH 7. The efficiency of synthesized PCS photocatalyst was confirmed in terms of its activity towards Eosin (EY) and Crystal violet (CV) dyes mineralization. The photocatalytic degradation for EY and CV dyes at optimum conditions was 99.47% and 99.31% and followed second order reactions kinetics with 1.4314 and 0.551 rate constant, respectively. The polynomial quadratic model is the best-fitted response surface methodology (RSM) model having a maximum desirability factors value and significant terms, with R2 (0.9994) and adj R2 values (1.0).

Ultrasound-Assisted Dispersive Liquid-Liquid Microextraction Using Deep Eutectic Solvents (DESs) for Neutral Red Dye Spectrophotometric Determination.

Deep eutectic solvents (DES), which have low toxicity and are low cost, biodegradable, and easily synthesized, were used for the extraction of neutral red (NR) dye before its spectrophotometric analysis. DES, containing choline chloride as a hydrogen bond acceptor and phenol as a hydrogen bond donor with a molar ratio of 1:2, was used for the extraction of NR dye from aqueous media. The possible interaction of different DESs with NR was studied using density functional theory (DFT) calculations. Experimentally, a UV-visible spectrophotometer was used for the quantitative analysis. The most important parameters affecting method performance, such as pH, extraction temperature, DES type, its volume, THF volume, sonication time, and centrifugation time, were optimized. The developed method provides exceptional sensitivity in terms of LOD and LOQ, which were 2.2 and 7.3 µg/L respectively. The relative standard deviation was 1.35−1.5% (n = 10), and the pre-concentration factor was 40. The method was found to be linear in the range of 2−300 µg/L (R2 = 0.9967). The method was successfully used for the determination of NR in wastewater samples. Finally, the DES-based method presents operational simplicity, high sensitivity, and rapid determination (<5 min) compared with other analytical procedures.

Theoretical designing of selenium heterocyclic non-fullerene acceptors with enhanced power conversion efficiency for organic solar cells: a DFT/TD-DFT-based prediction and understanding.

In this study, we have designed and explored a new series of non-fullerene acceptors for possible applications in organic solar cells. We have designed four molecules named as APH1 to APH4 after end-capped modification of recently synthesized Y6-Se-4Cl molecule. Density functional theory and time dependent-density functional theory have been employed for computing geometric and photovoltaic parameters of the designed molecules. Designed molecules have displayed high values of fill factor and FF%. Further, high mobility of electrons and holes between metal electrodes are also noted for designed molecules. Good values of open circuit voltage enhance the power conversion efficiency in the APH1-APH4. Frontier molecular orbitals analysis and excitation energy values suggested easy transportation of charges between molecular orbitals. Moreover, red-shifting in the absorption spectrum with high oscillating strength is also noted in APH1 to APH4 as compared to reference molecules. Results of different opto-electronic and photovoltaic parameters recommended that APH1 to APH4 are effective contributors for the development of high performance organic solar cells.